This patch adds the support of hardware compatibiltiy layer to the
HNS3 VF Driver. This layer implements various {set|get} operations
over MAC address for a virtual port, RSS related configuration,
fetches the link status info from PF, does various VLAN related
configuration over the virtual port, queries the statistics from
the hardware etc.
This layer can directly interact with hardware through the
IMP(Integrated Mangement Processor) interface or can use mailbox
to interact with the PF driver.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of the mailbox to the VF driver. The
mailbox shall be used as an interface to communicate with the
PF driver for various purposes like {set|get} MAC related
operations, reset, link status etc. The mailbox supports both
synchronous and asynchronous command send to PF driver.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of command interface for communication with
the IMP(Integrated Management Processor) for HNS3 Virtual Function
Driver.
Each VF has support of CQP(Command Queue Pair) ring interface.
Each CQP consis of send queue CSQ and receive queue CRQ.
There are various commands a VF may support, like to query frimware
version, TQP management, statistics, interrupt related, mailbox etc.
This also contains code to initialize the command queue, manage the
command queue descriptors and Rx/Tx protocol with the command processor
in the form of various commands/results and acknowledgements.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MT7530 can treat each port as either VLAN-unaware port or VLAN-aware port
through the implementation of port matrix mode or port security mode on
the ingress port, respectively. On one hand, Each port has been acting as
the VLAN-unaware one whenever the device is created in the initial or
certain port joins or leaves into/from the bridge at the runtime. On the
other hand, the patch just filling the required callbacks for VLAN
operations is achieved via extending the port to be into port security
mode when the port is configured as VLAN-aware port. Which mode can make
the port be able to recognize VID from incoming packets and look up VLAN
table to validate and judge which port it should be going to. And the
range for VID from 1 to 4094 is valid for the hardware.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify lan9303_indirect_phy_wait_for_completion()
and lan9303_switch_wait_for_completion() by using a new function
lan9303_read_wait()
Changes v1 -> v2:
- param 'mask' type u32
- removed param 'value' (will probably never be used)
- add newline before return
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the transmit queue is known full, then don't keep aggregating
data. And the cp_partial flag which indicates that the current
aggregation buffer is full can be folded in to avoid more
conditionals.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is only ever a single instance of network device object
referencing the internal rndis object. Therefore the open_cnt atomic
is not necessary.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netvsc_receive_callback function was using RCU to find the
appropriate underlying netvsc_device. Since calling function already
had that pointer, this was unnecessary.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller (netvsc_receive) already has the net device pointer,
and should just pass that to functions rather than the hyperv device.
This eliminates several impossible error paths in the process.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When skb can not be allocated, update ethtool statisitics
rather than rx_dropped which is intended for netif_receive.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to what PHYLIB already does, make sure that
PHY_INTERFACE_MODE_MOCA is reported as PORT_BNC.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink_get_fixed_state() currently consults an optional "link_gpio"
GPIO descriptor, expand this mechanism to allow specifying a custom
callback. This is necessary to support out of band link notifcation
(e.g: from an interrupt within a MMIO register).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some subsystems like DSA may be trying to connect to a PHY through OF first,
and then attempt a connect using a local MDIO bus, remove the error message:
"unable to find PHY node" so we can let MAC drivers whether to print it or not.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We may not always be able to resolve a correct phy_interface_t value before
actually connecting to the PHY device, when that happens, just have
phylink_connect_phy() utilize what the PHY device/driver provided.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to let subsystems like DSA fully utilize PHYLINK, we need to be able
to communicate phy_device::flags from of_phy_{connect,attach} even when using
PHYLINK APIs.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not correct to return NULL when that is actually an error and
function returns errors in any other wrong case. In the same time,
the cpsw driver and davinci emac doesn't check error case while
creating channel and it can miss actual error. Also remove WARNs
replacing them on dev_err msgs.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for ethtool get_module_info() and get_module_eeprom()
callbacks that will dump necessary information for a SFP.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_napi_del is called implicitely by free_netdev, therefore we
don't have to do it explicitely.
When the probe error path is reached, the net_device isn't
registered yet. Therefore reordering the call to netif_napi_del
shouldn't cause any issues.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify probe error path and remove callback by using device-managed
functions.
rtl_disable_msi isn't needed any longer because the release callback
of pcim_enable_device does this implicitely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an option to configure the mux id, aggregation and commad feature
for existing rmnet devices. Implement the changelink netlink
operation for this.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an option to configure the rmnet aggregation and command features
on device creation. This is achieved by using the vlan flags option.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to send and receive packets over ethernet.
An example of usage is testing the data path on UML. This can be
achieved by setting up two UML instances in multicast mode and
associating rmnet over the UML ethernet device.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon de-multiplexing data from one real dev, the packets can be sent
to an unique rmnet device for a given mux id.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiplexing is always enabled when transmiting from a rmnet device,
so remove the redundant egress macros. De-multiplexing is always
enabled when receiving packets from a rmnet device, so remove those
ingress macros.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the success and consumed entries were actually in use.
Use standard error codes instead.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The values were not computed correctly. There are no significant
visible impact, though.
The intended size of RX buffer is 16 MB, and the default slot size is 1728.
So, NETVSC_DEFAULT_RX should be 16*1024*1024 / 1728 = 9709.
The intended size of TX buffer is 1 MB, and the slot size is 6144.
So, NETVSC_DEFAULT_TX should be 1024*1024 / 6144 = 170.
The patch puts the formula directly into the macro, and moves them to
hyperv_net.h, together with related macros.
Fixes: 5023a6db73 ("netvsc: increase default receive buffer size")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The max should be 31 MB on host with NVSP version > 2.
On legacy hosts (NVSP version <=2) only 15 MB receive buffer is allowed,
otherwise the buffer request will be rejected by the host, resulting
vNIC not coming up.
The NVSP version is only available after negotiation. So, we add the
limit checking for legacy hosts in netvsc_init_buf().
Fixes: 5023a6db73 ("netvsc: increase default receive buffer size")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs (for example the SMSC LAN8710/LAN8720) doesn't allow turning
the refclk on and off again during operation (according to their
datasheet). Nonetheless exactly this behaviour was introduced for power
saving reasons by commit e8fcfcd568 ("net: fec: optimize the clock management to save power").
Therefore add support for the phy_reset_after_clk_enable function from
phylib to mitigate this issue.
Generally speaking this issue is only relevant if the ref clk for the
PHY is generated by the SoC and therefore the PHY is configured to
"REF_CLK In Mode". In our specific case (PCB) this problem does occur at
about every 10th to 50th POR of an LAN8710 connected to an i.MX6SOLO
SoC. The typical symptom of this problem is a "swinging" ethernet link.
Similar issues were reported by users of the NXP forum:
https://community.nxp.com/thread/389902https://community.nxp.com/message/309354
With this patch applied the issue didn't occur for at least a few
hundret PORs of our board.
Fixes: e8fcfcd568 ("net: fec: optimize the clock management to save power")
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs need the refclk to be a continuous clock. Therefore they don't
allow turning it off and on again during operation. Nonetheless such a
clock switching is performed by some ETH drivers (namely FEC [1]) for
power saving reasons. An example for an affected PHY is the
SMSC/Microchip LAN8720 in "REF_CLK In Mode".
In order to provide a uniform method to overcome this problem this patch
adds a new phy_driver flag (PHY_RST_AFTER_CLK_EN) and corresponding
function phy_reset_after_clk_enable() to the phylib. These should be
used to trigger reset of the PHY after the refclk is switched on again.
[1] commit e8fcfcd568 ("net: fec: optimize the clock management to save power")
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs need a minimum time after the reset gpio was asserted and/or
deasserted. To ensure we meet these timing requirements add two new
optional devicetree parameters for the phy: reset-delay-us and
reset-post-delay-us.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch aligning values in the ethtool get_coalesce function.
This patch do not modify in anyway the driver's behaviour.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx/Tx ring sizes can be adjusted thanks to ethtool given specific
network needs. This commit splits the default ring size from its max
value to allow ethtool to vary the parameters in both ways.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check to only free the TSO header buffer when its
allocation previously succeeded.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the requested dump level parameter to big-endian at the start of
nfp_net_dump_calculate_size() and nfp_net_dump_populate_buffer(), then
compare and assign it directly where needed in the traversal and prolog
code. This decreases the total number of conversions used.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port matching is selected by default on every rule so remove check for it
and delete 'else' side of the statement. Remove nfp_flower_meta_one as now
it will not feature in the code. Rename nfp_flower_meta_two given that one
has been removed.
'Additional metadata' if statement can never be true so remove it as well.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the matching of mac/mpls as a default selection. These are not
necessarily set by a TC rule (unlike the port). Previously a mac/mpls
field would exist in every match and be masked out if not used. This patch
has no impact on functionality but removes unnessary memory assignment in
the match cmsg.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets that don't have dest mac as the mac of the master device should
not be entertained by the IPvlan rx-handler. This is mostly true as the
packet path mostly takes care of that, except when the master device is
a virtual device. As demonstrated in the following case -
ip netns add ns1
ip link add ve1 type veth peer name ve2
ip link add link ve2 name iv1 type ipvlan mode l2
ip link set dev iv1 netns ns1
ip link set ve1 up
ip link set ve2 up
ip -n ns1 link set iv1 up
ip addr add 192.168.10.1/24 dev ve1
ip -n ns1 addr 192.168.10.2/24 dev iv1
ping -c2 192.168.10.2
<Works!>
ip neigh show dev ve1
ip neigh show 192.168.10.2 lladdr <random> dev ve1
ping -c2 192.168.10.2
<Still works! Wrong!!>
This patch adds that missing check in the IPvlan rx-handler.
Reported-by: Amit Sikka <amit.sikka@ericsson.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most callers of rhashtable_walk_start don't care about a resize event
which is indicated by a return value of -EAGAIN. So calls to
rhashtable_walk_start are wrapped wih code to ignore -EAGAIN. Something
like this is common:
ret = rhashtable_walk_start(rhiter);
if (ret && ret != -EAGAIN)
goto out;
Since zero and -EAGAIN are the only possible return values from the
function this check is pointless. The condition never evaluates to true.
This patch changes rhashtable_walk_start to return void. This simplifies
code for the callers that ignore -EAGAIN. For the few cases where the
caller cares about the resize event, particularly where the table can be
walked in mulitple parts for netlink or seq file dump, the function
rhashtable_walk_start_check has been added that returns -EAGAIN on a
resize event.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) CAN fixes from Martin Kelly (cancel URBs properly in all the CAN usb
drivers).
2) Revert returning -EEXIST from __dev_alloc_name() as this propagates
to userspace and broke some apps. From Johannes Berg.
3) Fix conn memory leaks and crashes in TIPC, from Jon Malloc and Cong
Wang.
4) Gianfar MAC can't do EEE so don't advertise it by default, from
Claudiu Manoil.
5) Relax strict netlink attribute validation, but emit a warning. From
David Ahern.
6) Fix regression in checksum offload of thunderx driver, from Florian
Westphal.
7) Fix UAPI bpf issues on s390, from Hendrik Brueckner.
8) New card support in iwlwifi, from Ihab Zhaika.
9) BBR congestion control bug fixes from Neal Cardwell.
10) Fix port stats in nfp driver, from Pieter Jansen van Vuuren.
11) Fix leaks in qualcomm rmnet, from Subash Abhinov Kasiviswanathan.
12) Fix DMA API handling in sh_eth driver, from Thomas Petazzoni.
13) Fix spurious netpoll warnings in bnxt_en, from Calvin Owens.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
net: mvpp2: fix the RSS table entry offset
tcp: evaluate packet losses upon RTT change
tcp: fix off-by-one bug in RACK
tcp: always evaluate losses in RACK upon undo
tcp: correctly test congestion state in RACK
bnxt_en: Fix sources of spurious netpoll warnings
tcp_bbr: reset long-term bandwidth sampling on loss recovery undo
tcp_bbr: reset full pipe detection on loss recovery undo
tcp_bbr: record "full bw reached" decision in new full_bw_reached bit
sfc: pass valid pointers from efx_enqueue_unwind
gianfar: Disable EEE autoneg by default
tcp: invalidate rate samples during SACK reneging
can: peak/pcie_fd: fix potential bug in restarting tx queue
can: usb_8dev: cancel urb on -EPIPE and -EPROTO
can: kvaser_usb: cancel urb on -EPIPE and -EPROTO
can: esd_usb2: cancel urb on -EPIPE and -EPROTO
can: ems_usb: cancel urb on -EPIPE and -EPROTO
can: mcba_usb: cancel urb on -EPROTO
usbnet: fix alignment for frames with no ethernet header
tcp: use current time in tcp_rcv_space_adjust()
...
Pull virtio bugfixes from Michael Tsirkin:
"A couple of minor bugfixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_net: fix return value check in receive_mergeable()
virtio_mmio: add cleanup for virtio_mmio_remove
virtio_mmio: add cleanup for virtio_mmio_probe
Marc Kleine-Budde says:
====================
pull-request: can 2017-12-08
this is a pull request of 6 patches for net/master.
Martin Kelly provides 5 patches for various USB based CAN drivers, that
properly cancel the URBs on adapter unplug, so that the driver doesn't
end up in an endless loop. Stephane Grosjean provides a patch to restart
the tx queue if zero length packages are transmitted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers fixes for 4.15
Second set of fixes for 4.15. This time a lot of iwlwifi patches and
two brcmfmac patches. Most important here are the MIC and IVC fixes
for iwlwifi to unbreak 9000 series.
iwlwifi
* fix rate-scaling to not start lowest possible rate
* fix the TX queue hang detection for AP/GO modes
* fix the TX queue hang timeout in monitor interfaces
* fix packet injection
* remove a wrong error message when dumping PCI registers
* fix race condition with RF-kill
* tell mac80211 when the MIC has been stripped (9000 series)
* tell mac80211 when the IVC has been stripped (9000 series)
* add 2 new PCI IDs, one for 9000 and one for 22000
* fix a queue hang due during a P2P Remain-on-Channel operation
brcmfmac
* fix a race which sometimes caused a crash during sdio unbind
* fix a kernel-doc related build error
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
