The bracketing for the interrupts property in the device tree
example is incorrect. Fix it.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Update VIC and Host1x bindings for changes in Tegra234.
Namely,
- New compatible strings
- Sharded syncpoint interrupts
- Optional reset.
Also, fix the order of descriptions for VM/hypervisor
register apertures -- while the reg-names specification
was correct, the descriptions for these were switched.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This code works, but technically it uses "num_in_bus_fmts" before it
has been initialized so it leads to static checker warnings and probably
KMEMsan warnings at run time. Initialize the variable to zero to
silence the warning.
Fixes: f32df58acc ("drm/bridge: Add the necessary bits to support bus format negotiation")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/YrrIs3hoGcPVmXc5@kili
Allwinner display drivers are split roughly into two generations. The
first generation was found on early 32-bit ARM SoCs and contains DE1.0
and a custom HDMI controller. Clarify that these options only apply to
a specific list of SoCs, and limit selecting them to 32-bit ARM, to
avoid confusion.
The second generation, found in A83T and newer SoCs (both 32-bit and
64-bit), contains a DE2.0 and a DesignWare HDMI controller. Since this
is the most widely-used generation, enable it by default. The previous
default condition (MACH_SUN8I) was limited to 32-bit SoCs. Also enable
the DSI controller by default, which is found on 64-bit SoCs as well.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220702193250.52959-1-samuel@sholland.org
The current code tries to handle the case where CONFIG_PM isn't selected
by first calling our runtime_resume implementation and then properly
report the power state to the runtime_pm core.
This allows to have a functionning device even if pm_runtime_get_*
functions are nops.
However, the device power state if CONFIG_PM is enabled is
RPM_SUSPENDED, and thus our vc4_hdmi_write() and vc4_hdmi_read() calls
in the runtime_pm hooks will now report a warning since the device might
not be properly powered.
Even more so, we need CONFIG_PM enabled since the previous RaspberryPi
have a power domain that needs to be powered up for the HDMI controller
to be usable.
The previous patch has created a dependency on CONFIG_PM, now we can
just assume it's there and only call pm_runtime_resume_and_get() to make
sure our device is powered in bind.
Link: https://lore.kernel.org/r/20220629123510.1915022-39-maxime@cerno.tech
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Pull NVMe fixes from Christoph:
"nvme fixes for Linux 5.19
- another bogus identifier quirk (Keith Busch)
- use struct group in the tracer to avoid a gcc warning (Keith Busch)"
* tag 'nvme-5.19-2022-07-07' of git://git.infradead.org/nvme:
nvme: use struct group for generic command dwords
nvme-pci: phison e16 has bogus namespace ids
This patch ensures that the clock notifier is unregistered
when driver probe is returning error.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: Satish Nagireddy <satish.nagireddy@getcruise.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
nouveau_bo_init() is backed by ttm_bo_init() and ferries its return code
back to the caller. On failures, ttm will call nouveau_bo_del_ttm() and
free the memory.Thus, when nouveau_bo_init() returns an error, the gem
object has already been released. Then the call to nouveau_bo_ref() will
use the freed "nvbo->bo" and lead to a use-after-free bug.
We should delete the call to nouveau_bo_ref() to avoid the use-after-free.
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 019cbd4a4f ("drm/nouveau: Initialize GEM object before TTM object")
Cc: Thierry Reding <treding@nvidia.com>
Cc: <stable@vger.kernel.org> # v5.4+
Link: https://patchwork.freedesktop.org/patch/msgid/20220705132546.2247677-1-niejianglei2021@163.com
Pull a devfreq fix for 5.19-rc6 from Chanwoo Choi:
"- Fix exynos-bus NULL pointer dereference by correctly using the local
generated freq_table to output the debug values instead of using the
profile freq_table that is not used in the driver."
* tag 'devfreq-fixes-for-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux:
PM / devfreq: exynos-bus: Fix NULL pointer dereference
Pull LoongArch fixes from Huacai Chen:
"A fix for tinyconfig build error, a fix for section mismatch warning,
and two cleanups of obsolete code"
* tag 'loongarch-fixes-5.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: Fix section mismatch warning
LoongArch: Fix build errors for tinyconfig
LoongArch: Remove obsolete mentions of vcsr
LoongArch: Drop these obsolete selects in Kconfig
Pull networking fixes from Paolo Abeni:
"Including fixes from bpf, netfilter, can, and bluetooth.
Current release - regressions:
- bluetooth: fix deadlock on hci_power_on_sync
Previous releases - regressions:
- sched: act_police: allow 'continue' action offload
- eth: usbnet: fix memory leak in error case
- eth: ibmvnic: properly dispose of all skbs during a failover
Previous releases - always broken:
- bpf:
- fix insufficient bounds propagation from
adjust_scalar_min_max_vals
- clear page contiguity bit when unmapping pool
- netfilter: nft_set_pipapo: release elements in clone from
abort path
- mptcp: netlink: issue MP_PRIO signals from userspace PMs
- can:
- rcar_canfd: fix data transmission failed on R-Car V3U
- gs_usb: gs_usb_open/close(): fix memory leak
Misc:
- add Wenjia as SMC maintainer"
* tag 'net-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (57 commits)
wireguard: Kconfig: select CRYPTO_CHACHA_S390
crypto: s390 - do not depend on CRYPTO_HW for SIMD implementations
wireguard: selftests: use microvm on x86
wireguard: selftests: always call kernel makefile
wireguard: selftests: use virt machine on m68k
wireguard: selftests: set fake real time in init
r8169: fix accessing unset transport header
net: rose: fix UAF bug caused by rose_t0timer_expiry
usbnet: fix memory leak in error case
Revert "tls: rx: move counting TlsDecryptErrors for sync"
mptcp: update MIB_RMSUBFLOW in cmd_sf_destroy
mptcp: fix local endpoint accounting
selftests: mptcp: userspace PM support for MP_PRIO signals
mptcp: netlink: issue MP_PRIO signals from userspace PMs
mptcp: Acquire the subflow socket lock before modifying MP_PRIO flags
mptcp: Avoid acquiring PM lock for subflow priority changes
mptcp: fix locking in mptcp_nl_cmd_sf_destroy()
net/mlx5e: Fix matchall police parameters validation
net/sched: act_police: allow 'continue' action offload
net: lan966x: hardcode the number of external ports
...
Pull pin control fixes from Linus Walleij:
- Tag Intel pin control as supported in MAINTAINERS
- Fix a NULL pointer exception in the Aspeed driver
- Correct some NAND functions in the Sunxi A83T driver
- Use the right offset for some Sunxi pins
- Fix a zero base offset in the Freescale (NXP) i.MX93
- Fix the IRQ support in the STM32 driver
* tag 'pinctrl-v5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: stm32: fix optional IRQ support to gpios
pinctrl: imx: Add the zero base flag for imx93
pinctrl: sunxi: sunxi_pconf_set: use correct offset
pinctrl: sunxi: a83t: Fix NAND function name for some pins
pinctrl: aspeed: Fix potential NULL dereference in aspeed_pinmux_set_mux()
MAINTAINERS: Update Intel pin control to Supported
These are indeed "should not happen" situations, but it turns out recent
changes made the 'task_is_stopped_or_trace()' case trigger (fix for that
exists, is pending more testing), and the BUG_ON() makes it
unnecessarily hard to actually debug for no good reason.
It's been that way for a long time, but let's make it clear: BUG_ON() is
not good for debugging, and should never be used in situations where you
could just say "this shouldn't happen, but we can continue".
Use WARN_ON_ONCE() instead to make sure it gets logged, and then just
continue running. Instead of making the system basically unusuable
because you crashed the machine while potentially holding some very core
locks (eg this function is commonly called while holding 'tasklist_lock'
for writing).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit fd27de58b0ad ("dt-bindings: display: tegra: Convert to json-schema")
converts nvidia,tegra20-host1x.txt to yaml, but missed to adjust its
references in MAINTAINERS.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a
broken reference.
Repair these file references in NVIDIA TEGRA DRM and VIDEO DRIVER.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Convert the Tegra host1x controller bindings from the free-form text
format to json-schema.
This also adds the missing display-hub DT bindings that were not
previously documented.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tue, Jun 28, 2022 at 04:28:58PM +0800, Pengfei Xu wrote:
> # ./ftracetest
> === Ftrace unit tests ===
> [1] Basic trace file check [PASS]
> [2] Basic test for tracers [PASS]
> [3] Basic trace clock test [PASS]
> [4] Basic event tracing check [PASS]
> [5] Change the ringbuffer size [PASS]
> [6] Snapshot and tracing setting [PASS]
> [7] trace_pipe and trace_marker [PASS]
> [8] Test ftrace direct functions against tracers [UNRESOLVED]
> [9] Test ftrace direct functions against kprobes [UNRESOLVED]
> [10] Generic dynamic event - add/remove eprobe events [FAIL]
> [11] Generic dynamic event - add/remove kprobe events
>
> It 100% reproduced in step 11 and then missing ENDBR BUG generated:
> "
> [ 9332.752836] mmiotrace: enabled CPU7.
> [ 9332.788612] mmiotrace: disabled.
> [ 9337.103426] traps: Missing ENDBR: syscall_regfunc+0x0/0xb0
It turns out that while syscall_regfunc() does have an ENDBR when
generated, it gets sealed by objtool's .ibt_endbr_seal list.
Since the only text references to this function:
$ git grep syscall_regfunc
include/linux/tracepoint.h:extern int syscall_regfunc(void);
include/trace/events/syscalls.h: syscall_regfunc, syscall_unregfunc
include/trace/events/syscalls.h: syscall_regfunc, syscall_unregfunc
kernel/tracepoint.c:int syscall_regfunc(void)
appear in the __tracepoint section which is excluded by objtool.
Fixes: 3c6f9f77e6 ("objtool: Rework ibt and extricate from stack validation")
Reported-by: Pengfei Xu <pengfei.xu@intel.com
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/Yrrepdaow4F5kqG0@hirez.programming.kicks-ass.net
cec_unregister_adapter() assumes that the underlying adapter ops are
callable. For example, if the CEC adapter currently has a valid physical
address, then the unregistration procedure will invalidate the physical
address by setting it to f.f.f.f. Whence the following kernel oops
observed after removing the adv7511 module:
Unable to handle kernel execution of user memory at virtual address 0000000000000000
Internal error: Oops: 86000004 [#1] PREEMPT_RT SMP
Call trace:
0x0
adv7511_cec_adap_log_addr+0x1ac/0x1c8 [adv7511]
cec_adap_unconfigure+0x44/0x90 [cec]
__cec_s_phys_addr.part.0+0x68/0x230 [cec]
__cec_s_phys_addr+0x40/0x50 [cec]
cec_unregister_adapter+0xb4/0x118 [cec]
adv7511_remove+0x60/0x90 [adv7511]
i2c_device_remove+0x34/0xe0
device_release_driver_internal+0x114/0x1f0
driver_detach+0x54/0xe0
bus_remove_driver+0x60/0xd8
driver_unregister+0x34/0x60
i2c_del_driver+0x2c/0x68
adv7511_exit+0x1c/0x67c [adv7511]
__arm64_sys_delete_module+0x154/0x288
invoke_syscall+0x48/0x100
el0_svc_common.constprop.0+0x48/0xe8
do_el0_svc+0x28/0x88
el0_svc+0x1c/0x50
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x15c/0x160
Code: bad PC value
---[ end trace 0000000000000000 ]---
Protect against this scenario by unregistering i2c_cec after
unregistering the CEC adapter. Duly disable the CEC clock afterwards
too.
Fixes: 3b1b975003 ("drm: adv7511/33: add HDMI CEC support")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220612144854.2223873-3-alvin@pqrs.dk
Fix a kernel NULL pointer dereference reported by gpio kselftests.
linereq_free() can be called as part of the cleanup of a failed request,
at which time the desc for a line may not have been determined, so it
is unsafe to dereference without a check.
Add a check prior to dereferencing the line desc.
Fixes: 2068339a6c ("gpiolib: cdev: Add hardware timestamp clock type")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
init_numa_memory() is annotated __init and not used by any module,
thus don't export it.
Remove not needed EXPORT_SYMBOL for init_numa_memory() to fix the
following section mismatch warning:
MODPOST vmlinux.symvers
WARNING: modpost: vmlinux.o(___ksymtab+init_numa_memory+0x0): Section mismatch in reference
from the variable __ksymtab_init_numa_memory to the function .init.text:init_numa_memory()
The symbol init_numa_memory is exported and annotated __init
Fix this by removing the __init annotation of init_numa_memory or drop the export.
This is build on Linux 5.19-rc4.
Fixes: d4b6f1562a ("LoongArch: Add Non-Uniform Memory Access (NUMA) support")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Building loongarch:tinyconfig fails with the following error.
./arch/loongarch/include/asm/page.h: In function 'pfn_valid':
./arch/loongarch/include/asm/page.h:42:32: error: 'PHYS_OFFSET' undeclared
Add the missing include file and fix succeeding vdso errors.
Fixes: 09cfefb7fa ("LoongArch: Add memory management")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
The `vcsr` only exists in the old hardware design, it isn't used in any
shipped hardware from Loongson-3A5000 on. Both scalar FP and LSX/LASX
instructions use the `fcsr` as their control and status registers now.
For example, the RM control bit in fcsr0 is shared by FP, LSX and LASX
instructions.
Particularly, fcsr16 to fcsr31 are reserved for LSX/LASX now, access to
these registers has no visible effect if LSX/LASX is enabled, and will
cause SXD/ASXD exceptions if LSX/LASX is not enabled.
So, mentions of vcsr are obsolete in the first place (it was just used
for debugging), let's remove them.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Qi Hu <huqi@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Commit fa96b57c14 ("LoongArch: Add build infrastructure") adds the new
file arch/loongarch/Kconfig.
As the work on LoongArch was probably quite some time under development,
various config symbols have changed and disappeared from the time of
initial writing of the Kconfig file and its inclusion in the repository.
The following four commits:
commit c126a53c27 ("arch: remove GENERIC_FIND_FIRST_BIT entirely")
commit 140c8180eb ("arch: remove HAVE_COPY_THREAD_TLS")
commit aca52c3983 ("mm: remove CONFIG_HAVE_MEMBLOCK")
commit 3f08a302f5 ("mm: remove CONFIG_HAVE_MEMBLOCK_NODE_MAP option")
remove the mentioned config symbol, and enable the intended setup by
default without configuration.
Drop these obsolete selects in loongarch's Kconfig.
Reviewed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Use the fbcon_info_from_console() wrapper which was added to kernel
v5.19 with commit 409d6c95f9 ("fbcon: Introduce wrapper for console->fb_info lookup").
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Verify that the fbdev or drm driver correctly adjusted the virtual
screen sizes. On failure report the failing driver and reject the screen
size change.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org # v5.4+
We need to prevent that users configure a screen size which is smaller than the
currently selected font size. Otherwise rendering chars on the screen will
access memory outside the graphics memory region.
This patch adds a new function fbcon_modechange_possible() which
implements this check and which later may be extended with other checks
if necessary. The new function is called from the FBIOPUT_VSCREENINFO
ioctl handler in fbmem.c, which will return -EINVAL if userspace asked
for a too small screen size.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org # v5.4+
Prevent that users set a font size which is bigger than the physical screen.
It's unlikely this may happen (because screens are usually much larger than the
fonts and each font char is limited to 32x32 pixels), but it may happen on
smaller screens/LCD displays.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org # v4.14+
Jason A. Donenfeld says:
====================
wireguard patches for 5.19-rc6
1) A few small fixups to the selftests, per usual. Of particular note is
a fix for a test flake that occurred on especially fast systems that
boot in less than a second.
2) An addition during this cycle of some s390 crypto interacted with the
way wireguard selects dependencies, resulting in linker errors
reported by the kernel test robot. So Vladis sent in a patch for
that, which also required a small preparatory fix moving some Kconfig
symbols around.
====================
Link: https://lore.kernel.org/r/20220707003157.526645-1-Jason@zx2c4.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Various accelerated software implementation Kconfig values for S390 were
mistakenly placed into drivers/crypto/Kconfig, even though they're
mainly just SIMD code and live in arch/s390/crypto/ like usual. This
gives them the very unusual dependency on CRYPTO_HW, which leads to
problems elsewhere.
This patch fixes the issue by moving the Kconfig values for non-hardware
drivers into the usual place in crypto/Kconfig.
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This makes for faster tests, faster compile time, and allows us to ditch
ACPI finally.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These selftests are used for much more extensive changes than just the
wireguard source files. So always call the kernel's build file, which
will do something or nothing after checking the whole tree, per usual.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Not all platforms have an RTC, and rather than trying to force one into
each, it's much easier to just set a fixed time. This is necessary
because WireGuard's latest handshakes parameter is returned in wallclock
time, and if the system time isn't set, and the system is really fast,
then this returns 0, which trips the test.
Turning this on requires setting CONFIG_COMPAT_32BIT_TIME=y, as musl
doesn't support settimeofday without it.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are UAF bugs caused by rose_t0timer_expiry(). The
root cause is that del_timer() could not stop the timer
handler that is running and there is no synchronization.
One of the race conditions is shown below:
(thread 1) | (thread 2)
| rose_device_event
| rose_rt_device_down
| rose_remove_neigh
rose_t0timer_expiry | rose_stop_t0timer(rose_neigh)
... | del_timer(&neigh->t0timer)
| kfree(rose_neigh) //[1]FREE
neigh->dce_mode //[2]USE |
The rose_neigh is deallocated in position [1] and use in
position [2].
The crash trace triggered by POC is like below:
BUG: KASAN: use-after-free in expire_timers+0x144/0x320
Write of size 8 at addr ffff888009b19658 by task swapper/0/0
...
Call Trace:
<IRQ>
dump_stack_lvl+0xbf/0xee
print_address_description+0x7b/0x440
print_report+0x101/0x230
? expire_timers+0x144/0x320
kasan_report+0xed/0x120
? expire_timers+0x144/0x320
expire_timers+0x144/0x320
__run_timers+0x3ff/0x4d0
run_timer_softirq+0x41/0x80
__do_softirq+0x233/0x544
...
This patch changes rose_stop_ftimer() and rose_stop_t0timer()
in rose_remove_neigh() to del_timer_sync() in order that the
timer handler could be finished before the resources such as
rose_neigh and so on are deallocated. As a result, the UAF
bugs could be mitigated.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220705125610.77971-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To avoid preventing the display from coming up before the rootfs is
mounted, without resorting to packing fw in the initrd, the GPU has
this limbo state where the device is probed, but we aren't ready to
start sending commands to it. This is particularly problematic for
a6xx, since the GMU (which requires fw to be loaded) is the one that
is controlling the power/clk/icc votes.
So defer enabling runpm until we are ready to call gpu->hw_init(),
as that is a point where we know we have all the needed fw and are
ready to start sending commands to the coproc's.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/489337/
Link: https://lore.kernel.org/r/20220613182036.2567963-1-robdclark@gmail.com
