The commit 3416609363 ("tuntap: use common code for virtio_net_hdr
and skb GSO conversion") replaced the tun code for header manipulation
with the generic helpers. While doing so, it implictly moved the
skb_partial_csum_set() invocation after eth_type_trans(), which
invalidate the current gso start/offset values.
Fix it by moving the helper invocation before the mac pulling.
Fixes: 3416609363 ("tuntap: use common code for virtio_net_hdr and skb GSO conversion")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 multicast and link-local addresses require special handling by the
VRF driver:
1. Rather than using the VRF device index and full FIB lookups,
packets to/from these addresses should use direct FIB lookups based on
the VRF device table.
2. fail sends/receives on a VRF device to/from a multicast address
(e.g, make ping6 ff02::1%<vrf> fail)
3. move the setting of the flow oif to the first dst lookup and revert
the change in icmpv6_echo_reply made in ca254490c8 ("net: Add VRF
support to IPv6 stack"). Linklocal/mcast addresses require use of the
skb->dev.
With this change connections into and out of a VRF enslaved device work
for multicast and link-local addresses work (icmp, tcp, and udp)
e.g.,
1. packets into VM with VRF config:
ping6 -c3 fe80::e0:f9ff:fe1c:b974%br1
ping6 -c3 ff02::1%br1
ssh -6 fe80::e0:f9ff:fe1c:b974%br1
2. packets going out a VRF enslaved device:
ping6 -c3 fe80::18f8:83ff:fe4b:7a2e%eth1
ping6 -c3 ff02::1%eth1
ssh -6 root@fe80::18f8:83ff:fe4b:7a2e%eth1
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow drivers to pass flow arg to functions where the arg is not const
and allow the driver to make updates as needed (eg., setting oif).
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DT support to the Cirrus Logic CS89x0 driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the patchset about adding support of ACPI (commit id is 6343488)
being applied, HNS does not depend on OF. It depends on OF or ACPI, so
the Kconfig file needs to be updated.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user may change the speed. Use it to replace the default one.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move calling set_speed() from open() to rtl_hw_phy_work_func_t().
Then, we would set the default speed only for first initialization
or after resuming.
Besides, the set_speed() could handle the flag of PHY_RESET which
would be set in rtl_ops.hw_phy_cfg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the settings of PHY to a work queue and schedule it after
rtl_ops.init().
There are some reasons for this. First, the settings are only
needed for the first time initialization or after the power
down occurs.
Second, the settings are independent with the others.
Last, the settings may take more time than the others. Leave
they in probe() or open() may delay the following flows.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some cards do not support autoneg. The current code does not prevent the
user from enabling autoneg with ethtool on such cards, causing confusion.
Firmware provides the autoneg capability information and we just need to
store it in the support_auto_speeds field in bnxt_link_info struct.
The ethtool set_settings() call will check this field before proceeding
with autoneg.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add bnxt_gro_func_5731x() to handle GRO packets for this chip. The
completion structures used in the new chip have new data to help determine
the header offsets. The offsets can be off by 4 if the packet is an
internal loopback packet (e.g. from one VF to another VF). Some additional
logic is added to adjust the offsets if it is a loopback packet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer chips require different logic to handle GRO packets. So refactor
the code so that we can call different functions depending on the chip.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define all the supported chip numbers and chip categories. Store the
chip_num returned by firmware. If the call to get the version and chip
number fails, we should abort.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NPAR type is read from bnxt_hwrm_func_qcfg. Do not allow changing link
parameters if in NPAR mode sinc ethe port is shared among multiple
partitions. The link parameters are set up by firmware.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VF driver gets this event, the VF configuration has changed (such
as default VLAN). The VF driver will initiate a silent reset to pick up
the new configuration.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a default VLAN is added to the VF, the VF driver needs to reset to
pick up the default VLAN ID. We can use the same tx timeout reset logic
to do that, without the debug output. This new function, with the
silent parameter to suppress debug output will now serve both purposes.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF can setup a default VLAN for a VF. The default VLAN tag is
automatically inserted and stripped without the knowledge of the
stack running on the VF. The VF driver needs to know that default
VLAN is enabled as VLAN acceleration on the RX side is no longer
supported. Call netdev_update_features() to fix up the VLAN features
as necessary. Also, VLAN strip mode must be enabled to strip out
the default VLAN tag.
Only allow VF default VLAN to be set if the firmware spec is >= 1.2.1.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the enic driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit e858fae2b0 ("virtio_net: use common code for virtio_net_hdr
and skb GSO conversion") replaced the tun code for header manipulation
with the generic helpers. While doing so, it implictly moved the
skb_partial_csum_set() invocation after eth_type_trans(), which
invalidate the current gso start/offset values.
Fix it by moving the helper invocation before the mac pulling.
Fixes: e858fae2b0 ("virtio_net: use common code for virtio_net_hdr and
skb GSO conversion")
Reported-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since msleep is based on jiffies the PHY reset could take longer
than expected. So use msleep for values greater than 20 msec otherwise
usleep_range.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iProc based SoCs supports the integrated mdio multiplexer which
has the bus selection as well as mdio transaction generation logic
inside.
This multiplexer has child buses for PCIe, SATA, USB and ETH. These
buses could be internal or external to SOC where PHYs are attached.
These buses could use C-45 or C-22 mdio transaction.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An integrated multiplexer uses same address space for
"muxed bus selection" and "generation of mdio transaction"
hence its good to register parent bus from mux driver.
Hence added a mechanism where mux driver could register a
parent bus and pass it down to framework via mdio_mux_init api.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
For the next cycle, we have the following:
* the biggest change is Michał's work on integrating FQ/codel
with the mac80211 internal software queues
* cfg80211 connect result gets clarified for the
"no connection at all" case
* advertisement of per-interface type capabilities, in case
they differ (which makes a lot of sense for some capabilities)
* most of the nl80211 & hwsim unprivileged namespace operation
changes
* human-readable VHT capabilities in debugfs
* some other cleanups, like spelling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace open coded conversion between virtio_net_hdr to skb GSO info with
virtio_net_hdr_{from,to}_skb
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace open coded conversion between virtio_net_hdr to skb GSO info with
virtio_net_hdr_{from,to}_skb
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace open coded conversion between virtio_net_hdr to skb GSO info with
virtio_net_hdr_{from,to}_skb
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Intel (former Lantiq) XWAY 11G and 22E PHYs.
These PHYs are also named PEF 7061, PEF 7071, PEF 7072.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/sched/act_police.c
net/sched/sch_drr.c
net/sched/sch_hfsc.c
net/sched/sch_prio.c
net/sched/sch_red.c
net/sched/sch_tbf.c
In net-next the drop methods of the packet schedulers got removed, so
the bug fixes to them in 'net' are irrelevant.
A packet action unload crash fix conflicts with the addition of the
new firstuse timestamp.
Signed-off-by: David S. Miller <davem@davemloft.net>
The device emulation may send segCnt of 1 for LRO packets.
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: Jin Heo <heoj@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_workqueue replaces deprecated create_workqueue().
A dedicated workqueue has been used since the workqueue
mlxsw_wq is used for FDB notif. processing with workitems that are
involved in normal device operation && because it's a network device
which can be depended upon during memory reclaim.
Workitems &trans->timeout_dw and &mlxsw_sp->fdb_notify.dw,
map to mlxsw_sp_fdb_notify_work (processes FDB notifications from the
underlying device and resolves the netdev to which the entry points to
and notifies the bridge using the switchdev notifier) and
mlxsw_emad_trans_timeout_work (provides async EMAD register access)
respectively. They require forward progress under memory pressure and
hence, WQ_MEM_RECLAIM has been set.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_workqueue replaces deprecated create_workqueue().
A dedicated workqueue has been used since the workitem viz
(&lio->txq_status_wq.wk.work which maps to octnet_poll_check_txq_status)
is involved in a brief poll routine for checking transmit queue status
and is an intergral part of normal device operation.
WQ_MEM_RECLAIM has been set to guarantee forward progress under memory
pressure, which is a requirement here.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary.
flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4 RSS is limited to spread incoming packets to a power of two number
of queues.
An uniformly distibuted traffic would be split on queues 0 to N-1, N
being a power of two, each queue having a 1/N weight.
If number of RX queues is not a power of two, upper RX queues do not
receive traffic.
ethtool -x is lying, because it pretends some queues have higher weight.
Before patch:
lpaa24:~# ethtool -L eth1 rx 24
lpaa24:~# ethtool -x eth1
RX flow hash indirection table for eth1 with 24 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 10 11 12 13 14 15
16: 0 1 2 3 4 5 6 7
RSS hash key:
e0:7c:3a:89:07:55:b6:58:69:cc:f4:e5:24:62:e3:25:88:6c:42:5b:d2:cb:9a:d2:e0:06:e1:dc:f9:09:a1:89:0f:a0:30:43:73:6f:0c:b6
If this information was correct, user space tools could expect queues 0
to 7 to receive twice more traffic than queues 8 to 15
After patch :
lpaa24:~# ethtool -L eth1 rx 24
lpaa24:~# ethtool -x eth1
RX flow hash indirection table for eth1 with 24 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 10 11 12 13 14 15
RSS hash key:
da:7b:09:60:f1:ac:67:b4:d0:72:d4:ec:a2:e5:80:0a:ad:50:22:1a:f8:f9:66:54:5f:22:45:c3:88:f4:57:82:c1:c1:90:ed:70:cb:40:ce
lpaa24:~# ethtool -X eth1 equal 8
lpaa24:~# ethtool -x eth1
RX flow hash indirection table for eth1 with 24 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 0 1 2 3 4 5 6 7
RSS hash key:
da:7b:09:60:f1:ac:67:b4:d0:72:d4:ec:a2:e5:80:0a:ad:50:22:1a:f8:f9:66:54:5f:22:45:c3:88:f4:57:82:c1:c1:90:ed:70:cb:40:ce
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac4_set_umac_addr() takes a struct mac_device_info as
the first parameter, but is being passed a ioaddr instead from
dwmac4_set_filter(). Fix the warning/bug by changing the first
parameter.
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c:159:46: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c:159:46: expected struct mac_device_info *hw
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c:159:46: got void [noderef] <asn:2>*ioaddr
Note, only compile tested this as do not have any
hardware with it in.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace netdev_alloc_skb_ip_align() with napi_alloc_skb() which can save
several CPU cycles by avoiding having to disable and re-enable IRQs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a few netdev statistics to report transmitted and received bytes and
packets and a few obvious errors.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the statistics from the BGMAC's builtin MAC and return them to
user-space using the standard ethtool helpers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing different helpers to be utilized against
network devices created by the bgmac driver, make sure that we bind the
net_device with core->dev.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Kellermann reported a kernel crash with 4.5.0 when IPv6 is
disabled at boot using the kernel option ipv6.disable=1. Using
current net-next with the boot option:
$ ip link add red type vrf table 1001
Generates:
[12210.919584] BUG: unable to handle kernel NULL pointer dereference at 0000000000000748
[12210.921341] IP: [<ffffffff814b30e3>] fib6_get_table+0x2c/0x5a
[12210.922537] PGD b79e3067 PUD bb32b067 PMD 0
[12210.923479] Oops: 0000 [#1] SMP
[12210.924001] Modules linked in: ipvlan 8021q garp mrp stp llc
[12210.925130] CPU: 3 PID: 1177 Comm: ip Not tainted 4.7.0-rc1+ #235
[12210.926168] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[12210.928065] task: ffff8800b9ac4640 ti: ffff8800bacac000 task.ti: ffff8800bacac000
[12210.929328] RIP: 0010:[<ffffffff814b30e3>] [<ffffffff814b30e3>] fib6_get_table+0x2c/0x5a
[12210.930697] RSP: 0018:ffff8800bacaf888 EFLAGS: 00010202
[12210.931563] RAX: 0000000000000748 RBX: ffffffff81a9e280 RCX: ffff8800b9ac4e28
[12210.932688] RDX: 00000000000000e9 RSI: 0000000000000002 RDI: 0000000000000286
[12210.933820] RBP: ffff8800bacaf898 R08: ffff8800b9ac4df0 R09: 000000000052001b
[12210.934941] R10: 00000000657c0000 R11: 000000000000c649 R12: 00000000000003e9
[12210.936032] R13: 00000000000003e9 R14: ffff8800bace7800 R15: ffff8800bb3ec000
[12210.937103] FS: 00007faa1766c700(0000) GS:ffff88013ac00000(0000) knlGS:0000000000000000
[12210.938321] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[12210.939166] CR2: 0000000000000748 CR3: 00000000b79d6000 CR4: 00000000000406e0
[12210.940278] Stack:
[12210.940603] ffff8800bb3ec000 ffffffff81a9e280 ffff8800bacaf8c8 ffffffff814b3135
[12210.941818] ffff8800bb3ec000 ffffffff81a9e280 ffffffff81a9e280 ffff8800bace7800
[12210.943040] ffff8800bacaf8f0 ffffffff81397c88 ffff8800bb3ec000 ffffffff81a9e280
[12210.944288] Call Trace:
[12210.944688] [<ffffffff814b3135>] fib6_new_table+0x24/0x8a
[12210.945516] [<ffffffff81397c88>] vrf_dev_init+0xd4/0x162
[12210.946328] [<ffffffff814091e1>] register_netdevice+0x100/0x396
[12210.947209] [<ffffffff8139823d>] vrf_newlink+0x40/0xb3
[12210.948001] [<ffffffff814187f0>] rtnl_newlink+0x5d3/0x6d5
...
The problem above is due to the fact that the fib hash table is not
allocated when IPv6 is disabled at boot.
As for the VRF driver it should not do any IPv6 initializations if IPv6
is disabled, so it needs to know if IPv6 is disabled at boot. The disable
parameter is private to the IPv6 module, so provide an accessor for
modules to determine if IPv6 was disabled at boot time.
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I am not sure mlx4_en_netpoll() is doing anything useful right now.
mlx4 has different NAPI structures for RX and TX, and netpoll only wants
to drain TX queues.
Lets schedule NAPI polls on TX, not RX.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuration VLANs on B53 devices by implementing the
port VLAN add/del/dump functions. We currently default to a behavior
which is equivalent to having VLAN filtering turned on, where all VLANs
not programmed into the VLAN port-based vector will be discarded on
ingress.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for HW bridging by tying the ports together in the same port
VLAN mask when they belong to the same bridge, and isolating them to be
alone with the CPU port when they are not.
Propagate STP states from the bridge layer to the switch's HW mapping
when requested.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for FDB add/delete/dump using the ARL read/write logic and
the ARL search logic for faster dumps. The code is made flexible enough
it could support devices with a different register layout like BCM5325
and BCM5365 which have fewer number of entries or pack values into a
single 64 bits register.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM7445 STB chip has an issued in its revision D0 which was
previously worked around in drivers/net/dsa/bcm_sf2.c where we may
end-up double programming the integrated BCM7445 switch (bcm_sf2) and an
external Broadcom switch such as BCM53125, since these are mostly
register compatible.
Add a small quirk which just defers probing until we are sitting on the
slave DSA MDIO bus, which will allow us to intercept reads/writes and
funnel them through the SF2 internal MDIO master (which happens to
disconnect its pseudo PHY).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Broadcom's BCM53xx switch family, also known
as RoboSwitch. Some of these switches are ubiquituous, found in home
routers, Wi-Fi routers, DSL and cable modem gateways and other
networking related products.
This drivers adds the library driver (b53_common.c) as well as a few bus
glue drivers for MDIO, SPI, Switch Register Access Block (SRAB) and
memory-mapped I/O into a SoC's address space (Broadcom BCM63xx/33xx).
Basic operations are supported to bring the Layer 1/2 up and running,
but not much more at this point, subsequent patches add the remaining
features.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring VLANs on the Broadcom Starfigther2 switch.
This is all done through the bridge vlan facility just like other DSA
drivers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the definitions for the VLAN registers that we are going to
manipulate in subsequent patches.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-order the bcm_sf2_sw_setup() function so that it is at the far end of
the driver to avoid any kind of forward declarations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function to fast age something that is controlled by the
caller: port, VLAN. We will use this to implement a VLAN fast age
operation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
