Saeed Mahameed says:
====================
mlx5-next-2020-12-02
Low level mlx5 updates required by both netdev and rdma trees:
net/mlx5: Treat host PF vport as other (non eswitch manager) vport
net/mlx5: Enable host PF HCA after eswitch is initialized
net/mlx5: Rename peer_pf to host_pf
net/mlx5: Make API mlx5_core_is_ecpf accept const pointer
net/mlx5: Export steering related functions
net/mlx5: Expose other function ifc bits
net/mlx5: Expose IP-in-IP TX and RX capability bits
net/mlx5: Update the hardware interface definition for vhca state
net/mlx5: Update the list of the PCI supported devices
net/mlx5: Avoid exposing driver internal command helpers
net/mlx5: Add ts_cqe_to_dest_cqn related bits
net/mlx5: Add misc4 to mlx5_ifc_fte_match_param_bits
net/mlx5: Check dr mask size against mlx5_match_param size
net/mlx5: Add sampler destination type
net/mlx5: Add sample offload hardware bits and structures
====================
Link: https://lore.kernel.org/r/20201203011010.213440-1-saeedm@nvidia.com
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
At lest the revision 3.3.0 of the bosch m_can IP core specifies that valid
register values for "Nominal Time segment after sample point (NTSEG2)" are from
1 to 127. As the hardware uses a value of one more than the programmed value,
mean tseg2_min is 2.
This patch fixes the tseg2_min value accordingly.
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Mario Huettel <mario.huettel@gmx.net>
Acked-by: Sriram Dash <sriram.dash@samsung.com>
Link: https://lore.kernel.org/r/20201124190751.3972238-1-mkl@pengutronix.de
Fixes: b03cfc5bb0 ("can: m_can: Enable M_CAN version dependent initialization")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The threaded IRQ handler is used for the tcan4x5x driver only. The IRQ pin of
the tcan4x5x controller is active low, so better not use IRQF_TRIGGER_FALLING
when requesting the IRQ. As this can result in missing interrupts.
Further, if the device tree specified the interrupt as "IRQ_TYPE_LEVEL_LOW",
unloading and reloading of the driver results in the following error during
ifup:
| irq: type mismatch, failed to map hwirq-31 for gpio@20a8000!
| tcan4x5x spi1.1: m_can device registered (irq=0, version=32)
| tcan4x5x spi1.1 can2: TCAN4X5X successfully initialized.
| tcan4x5x spi1.1 can2: failed to request interrupt
This patch fixes the problem by removing the IRQF_TRIGGER_FALLING from the
request_threaded_irq().
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Sriram Dash <sriram.dash@samsung.com>
Cc: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/20201127093548.509253-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When eswitch manager is running on ECPF, host PF should be treated
as non eswitch manager port, similar to other VF vports.
Fail to do so, results in firmware treating PF's vport as ECPF
vport for eswitch ACL tables.
Non zero check to figure out if a given vport is other vport or not
is not sufficient becase PF vport number = 0 on ECPF.
Hence, create esw acl tables with an attribute of other vport.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently ECPF enables external host PF too early in the initialization
sequence for Ethernet links when ECPF is eswitch manager.
Due to this, when external host PF driver is loaded, host PF's HCA CAP has
inner_ip_version supported by NIC RX flow table.
This capability is later updated by firmware after ECPF driver enables
ENCAP/DECAP as eswitch manager.
This results into a timing race condition, where CREATE_TIR command
fails with a below syndrome on host PF.
mlx5_cmd_check:775:(pid 510): CREATE_TIR(0x900) op_mod(0x0) failed,
status bad parameter(0x3), syndrome (0x562b00)
Hence, enable the external host PF after necessary eswitch and per vport
initialization is completed.
Continue to enable host PF when eswitch manager capability is off for a
ECPF.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Export
mlx5_create_flow_table()
mlx5_create_flow_group()
mlx5_destroy_flow_group().
These symbols are required by the VDPA implementation to create rules
that consume VDPA specific traffic.
We do not deal with putting the prototypes in a header file since they
already exist in include/linux/mlx5/fs.h.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
mlx5 command init and cleanup routines are internal to mlx5_core driver.
Hence, avoid exporting them and move their definition to mlx5_core
driver's internal file mlx5_core.h
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This is to allow passing misc4 match param from userspace when
function like ib_flow_matcher_create is called.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The flow sampler object is a new destination type. Add a new member
for the flow destination.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This patch add a check to the mcp251xfd_probe() function to bail out and give
the user a proper error message if no IRQ is specified. Otherwise the driver
will probe just fine but ifup will fail with a meaningless "RTNETLINK answers:
Invalid argument" error message.
Link: https://lore.kernel.org/r/20201123113522.3820052-1-mkl@pengutronix.de
Reported-by: Niels Petter <petter@ka-long.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The firmware on the original USB2CAN by Geschwister Schneider Technologie
Entwicklungs- und Vertriebs UG exchanges all data between the host and the
device in host byte order. This is done with the struct
gs_host_config::byte_order member, which is sent first to indicate the desired
byte order.
The widely used open source firmware candleLight doesn't support this feature
and exchanges the data in little endian byte order. This breaks if a device
with candleLight firmware is used on big endianess systems.
To fix this problem, all u32 (but not the struct gs_host_frame::echo_id, which
is a transparent cookie) are converted to __le32.
Cc: Maximilian Schneider <max@schneidersoft.net>
Cc: Hubert Denkmair <hubert@denkmair.de>
Reported-by: Michael Rausch <mr@netadair.de>
Link: https://lore.kernel.org/r/b58aace7-61f3-6df7-c6df-69fee2c66906@netadair.de
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/r/20201120103818.3386964-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The tc-taprio base time indicates the beginning of the tc-taprio
schedule, which is cyclic by definition (where the length of the cycle
in nanoseconds is called the cycle time). The base time is a 64-bit PTP
time in the TAI domain.
Logically, the base-time should be a future time. But that imposes some
restrictions to user space, which has to retrieve the current PTP time
from the NIC first, then calculate a base time that will still be larger
than the base time by the time the kernel driver programs this value
into the hardware. Actually ensuring that the programmed base time is in
the future is still a problem even if the kernel alone deals with this.
Luckily, the enetc hardware already advances a base-time that is in the
past into a congruent time in the immediate future, according to the
same formula that can be found in the software implementation of taprio
(in taprio_get_start_time):
/* Schedule the start time for the beginning of the next
* cycle.
*/
n = div64_s64(ktime_sub_ns(now, base), cycle);
*start = ktime_add_ns(base, (n + 1) * cycle);
There's only one problem: the driver doesn't let the hardware do that.
It interferes with the base-time passed from user space, by special-casing
the situation when the base-time is zero, and replaces that with the
current PTP time. This changes the intended effective base-time of the
schedule, which will in the end have a different phase offset than if
the base-time of 0.000000000 was to be advanced by an integer multiple
of the cycle-time.
Fixes: 34c6adf197 ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201124220259.3027991-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Based on the discussion with Sukadev Bhattiprolu and Dany Madden,
we believe that checking adapter->resetting bit is preferred
since RESETTING state flag is not as strict as resetting bit.
RESETTING state flag is removed since it is verbose now.
Fixes: 7d7195a026 ("ibmvnic: Do not process device remove during device reset")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch fixes two lines in which the rx_offset received by the device
wasn't taken into account:
- prefetch function:
In our driver the copied data would reside in
rx_info->page + rx_headroom + rx_offset
so the prefetch function is changed accordingly.
- setting page_offset to zero for descriptors > 1:
for every descriptor but the first, the rx_offset is zero. Hence
the page_offset value should be set to rx_headroom.
The previous implementation changed the value of rx_info after
the descriptor was added to the SKB (essentially providing wrong
page offset).
Fixes: 68f236df93 ("net: ena: add support for the rx offset feature")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ENA driver uses the readless mechanism, which uses DMA, to find
out what the DMA mask is supposed to be.
If DMA is used without setting the dma_mask first, it causes the
Intel IOMMU driver to think that ENA is a 32-bit device and therefore
disables IOMMU passthrough permanently.
This patch sets the dma_mask to be ENA_MAX_PHYS_ADDR_SIZE_BITS=48
before readless initialization in
ena_device_init()->ena_com_mmio_reg_read_request_init(),
which is large enough to workaround the intel_iommu issue.
DMA mask is set again to the correct value after it's received from the
device after readless is initialized.
The patch also changes the driver to use dma_set_mask_and_coherent()
function instead of the two pci_set_dma_mask() and
pci_set_consistent_dma_mask() ones. Both methods achieve the same
effect.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Mike Cui <mikecui@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After request id is checked in validate_rx_req_id() its value is still
used in the line
rx_ring->free_ids[next_to_clean] =
rx_ring->ena_bufs[i].req_id;
even if it was found to be out-of-bound for the array free_ids.
The patch moves the request id to an earlier stage in the napi routine and
makes sure its value isn't used if it's found out-of-bounds.
Fixes: 30623e1ed1 ("net: ena: avoid memory access violation by validating req_id properly")
Signed-off-by: Ido Segev <idose@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dpaa2 driver depends on devlink, so it should select
NET_DEVLINK in order to fix compile errors, such as:
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.o: in function `dpaa2_eth_rx_err':
dpaa2-eth.c:(.text+0x3cec): undefined reference to `devlink_trap_report'
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth-devlink.o: in function `dpaa2_eth_dl_info_get':
dpaa2-eth-devlink.c:(.text+0x160): undefined reference to `devlink_info_driver_name_put'
Fixes: ceeb03ad8e ("dpaa2-eth: add basic devlink support")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20201123163553.1666476-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When performing IPv6 forwarding, there is an expectation that SKBs
will have some headroom. When forwarding a packet from the aquantia
driver, this does not always happen, triggering a kernel warning.
aq_ring.c has this code (edited slightly for brevity):
if (buff->is_eop && buff->len <= AQ_CFG_RX_FRAME_MAX - AQ_SKB_ALIGN) {
skb = build_skb(aq_buf_vaddr(&buff->rxdata), AQ_CFG_RX_FRAME_MAX);
} else {
skb = napi_alloc_skb(napi, AQ_CFG_RX_HDR_SIZE);
There is a significant difference between the SKB produced by these
2 code paths. When napi_alloc_skb creates an SKB, there is a certain
amount of headroom reserved. However, this is not done in the
build_skb codepath.
As the hardware buffer that build_skb is built around does not
handle the presence of the SKB header, this code path is being
removed and the napi_alloc_skb path will always be used. This code
path does have to copy the packet header into the SKB, but it adds
the packet data as a frag.
Fixes: 018423e90b ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Lincoln Ramsay <lincoln.ramsay@opengear.com>
Link: https://lore.kernel.org/r/MWHPR1001MB23184F3EAFA413E0D1910EC9E8FC0@MWHPR1001MB2318.namprd10.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Prevent VFs from resetting when PF driver is being unloaded:
- introduce new pf state: __I40E_VF_RESETS_DISABLED;
- check if pf state has __I40E_VF_RESETS_DISABLED state set,
if so, disable any further VFLR event notifications;
- when i40e_remove (rmmod i40e) is called, disable any resets on
the VFs;
Previously if there were bare-metal VFs passing traffic and PF
driver was removed, there was a possibility of VFs triggering a Tx
timeout right before iavf_remove. This was causing iavf_close to
not be called because there is a check in the beginning of iavf_remove
that bails out early if adapter->state < IAVF_DOWN_PENDING. This
makes it so some resources do not get cleaned up.
Fixes: 6a9ddb36ee ("i40e: disable IOV before freeing resources")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20201120180640.3654474-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kalle Valo says:
====================
wireless-drivers fixes for v5.10
First set of fixes for v5.10. One fix for iwlwifi kernel panic, others
less notable.
rtw88
* fix a bogus test found by clang
iwlwifi
* fix long memory reads causing soft lockup warnings
* fix kernel panic during Channel Switch Announcement (CSA)
* other smaller fixes
MAINTAINERS
* email address updates
* tag 'wireless-drivers-2020-11-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers:
iwlwifi: mvm: fix kernel panic in case of assert during CSA
iwlwifi: pcie: set LTR to avoid completion timeout
iwlwifi: mvm: write queue_sync_state only for sync
iwlwifi: mvm: properly cancel a session protection for P2P
iwlwifi: mvm: use the HOT_SPOT_CMD to cancel an AUX ROC
iwlwifi: sta: set max HE max A-MPDU according to HE capa
MAINTAINERS: update maintainers list for Cypress
MAINTAINERS: update Yan-Hsuan's email address
iwlwifi: pcie: limit memory read spin time
rtw88: fix fw_fifo_addr check
====================
Link: https://lore.kernel.org/r/20201123161037.C11D1C43460@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sometimes it takes longer than 5 seconds (watchdog timeout) to complete
failover, migration, and other resets. In stead of scheduling another
timeout reset, we wait for the current one to complete.
Suggested-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 61d3e1d9bc ("ibmvnic: Remove netdev notify for failover resets")
excluded the failover case for notify call because it said
netdev_notify_peers() can cause network traffic to stall or halt.
Current testing does not show network traffic stall
or halt because of the notify call for failover event.
netdev_notify_peers may be used when a device wants to inform the
rest of the network about some sort of a reconfiguration
such as failover or migration.
It is unnecessary to call that in other events like
FATAL, NON_FATAL, CHANGE_PARAM, and TIMEOUT resets
since in those scenarios the hardware does not change.
If the driver must do a hard reset, it is necessary to notify peers.
Fixes: 61d3e1d9bc ("ibmvnic: Remove netdev notify for failover resets")
Suggested-by: Brian King <brking@linux.vnet.ibm.com>
Suggested-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When netdev_notify_peers was substituted in
commit 986103e792 ("net/ibmvnic: Fix RTNL deadlock during device reset"),
call_netdevice_notifiers(NETDEV_RESEND_IGMP, dev) was missed.
Fix it now.
Fixes: 986103e792 ("net/ibmvnic: Fix RTNL deadlock during device reset")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tun only checks the file O_NONBLOCK flag, but it should also be checking
the iocb IOCB_NOWAIT flag. Any fops using ->read/write_iter() should check
both, otherwise it breaks users that correctly expect O_NONBLOCK semantics
if IOCB_NOWAIT is set.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/e9451860-96cc-c7c7-47b8-fe42cadd5f4c@kernel.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Starting with iOS 14 released in September 2020, connectivity using the
personal hotspot USB tethering function of iOS devices is broken.
Communication between the host and the device (for example ICMP traffic
or DNS resolution using the DNS service running in the device itself)
works fine, but communication to endpoints further away doesn't work.
Investigation on the matter shows that no UDP and ICMP traffic from the
tethered host is reaching the Internet at all. For TCP traffic there are
exchanges between tethered host and server but packets are modified in
transit leading to impossible communication.
After some trials Matti Vuorela discovered that reducing the URB buffer
size by two bytes restored the previous behavior. While a better
solution might exist to fix the issue, since the protocol is not
publicly documented and considering the small size of the fix, let's do
that.
Tested-by: Matti Vuorela <matti.vuorela@bitfactor.fi>
Signed-off-by: Yves-Alexis Perez <corsac@corsac.net>
Link: https://lore.kernel.org/linux-usb/CAAn0qaXmysJ9vx3ZEMkViv_B19ju-_ExN8Yn_uSefxpjS6g4Lw@mail.gmail.com/
Link: https://github.com/libimobiledevice/libimobiledevice/issues/1038
Link: https://lore.kernel.org/r/20201119172439.94988-1-corsac@corsac.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 9d2e5e9eeb ("cxgb4/ch_ktls: decrypted bit is not enough")
whenever CONFIG_TLS=m and CONFIG_CHELSIO_T4=y, the following build
failure occurs:
ld: drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.o: in function
`cxgb_select_queue':
cxgb4_main.c:(.text+0x2dac): undefined reference to `tls_validate_xmit_skb'
Fix this by ensuring that if TLS is set to be a module, CHELSIO_T4 will
also be compiled as a module. As otherwise the cxgb4 driver will not be
able to access TLS' symbols.
Fixes: 9d2e5e9eeb ("cxgb4/ch_ktls: decrypted bit is not enough")
Signed-off-by: Tom Seewald <tseewald@gmail.com>
Link: https://lore.kernel.org/r/20201120192528.615-1-tseewald@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
pull-request: can 2020-11-18
Jimmy Assarsson provides two patches for the kvaser_pciefd and kvaser_usb
drivers, where the can_bittiming_const are fixed.
The next patch is by me and fixes an erroneous flexcan_transceiver_enable()
during bus-off recovery in the flexcan driver.
Jarkko Nikula's patch for the m_can driver fixes the IRQ handler to only
process the interrupts if the device is not suspended.
* tag 'linux-can-fixes-for-5.10-20201118' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: m_can: process interrupt only when not runtime suspended
can: flexcan: flexcan_chip_start(): fix erroneous flexcan_transceiver_enable() during bus-off recovery
can: kvaser_usb: kvaser_usb_hydra: Fix KCAN bittiming limits
can: kvaser_pciefd: Fix KCAN bittiming limits
====================
Link: https://lore.kernel.org/r/20201118160414.2731659-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Slave function read the following capabilities from the wrong offset:
1. log_mc_entry_sz
2. fs_log_entry_sz
3. log_mc_hash_sz
Fix that by adjusting these capabilities offset to match firmware
layout.
Due to the wrong offset read, the following issues might occur:
1+2. Negative value reported at max_mcast_qp_attach.
3. Driver to init FW with multicast hash size of zero.
Fixes: a40ded6043 ("net/mlx4_core: Add masking for a few queries on HCA caps")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20201118081922.553-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Saeed Mahameed says:
====================
mlx5 fixes 2020-11-17
This series introduces some fixes to mlx5 driver.
* tag 'mlx5-fixes-2020-11-17' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: fix error return code in mlx5e_tc_nic_init()
net/mlx5: E-Switch, Fail mlx5_esw_modify_vport_rate if qos disabled
net/mlx5: Disable QoS when min_rates on all VFs are zero
net/mlx5: Clear bw_share upon VF disable
net/mlx5: Add handling of port type in rule deletion
net/mlx5e: Fix check if netdev is bond slave
net/mlx5e: Fix IPsec packet drop by mlx5e_tc_update_skb
net/mlx5e: Set IPsec WAs only in IP's non checksum partial case.
net/mlx5e: Fix refcount leak on kTLS RX resync
====================
Link: https://lore.kernel.org/r/20201117195702.386113-1-saeedm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the switch is hardware reset, it reads the contents of the
EEPROM. This can contain instructions for programming values into
registers and to perform waits between such programming. Reading the
EEPROM can take longer than the 100ms mv88e6xxx_hardware_reset() waits
after deasserting the reset GPIO. So poll the EEPROM done bit to
ensure it is complete.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ruslan Sushko <rus@sushko.dev>
Link: https://lore.kernel.org/r/20201116164301.977661-1-rus@sushko.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver sends Ethernet Management Datagram (EMAD) packets to the
device for configuration purposes and waits for up to 200ms for a reply.
A request is retried up to 5 times.
When the system is under heavy load, replies are not always processed in
time and EMAD transactions fail.
Make the process more robust to such delays by using exponential
backoff. First wait for up to 200ms, then retransmit and wait for up to
400ms and so on.
Fixes: caf7297e7a ("mlxsw: core: Introduce support for asynchronous EMAD register access")
Reported-by: Denis Yulevich <denisyu@nvidia.com>
Tested-by: Denis Yulevich <denisyu@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit cited below moved firmware flashing functionality from
mlxsw_spectrum to mlxsw_core, but did not adjust the Kconfig
dependencies. This makes it possible to have mlxsw_core as built-in and
mlxfw as a module. The mlxfw code is therefore not reachable from
mlxsw_core and firmware flashing fails:
# devlink dev flash pci/0000:01:00.0 file mellanox/mlxsw_spectrum-13.2008.1310.mfa2
devlink answers: Operation not supported
Fix by having mlxsw_core select mlxfw.
Fixes: b79cb787ac ("mlxsw: Move fw flashing code into core.c")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reported-by: Vadim Pasternak <vadimp@nvidia.com>
Tested-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Avoid processing bogus interrupt statuses when the HW is runtime suspended and
the M_CAN_IR register read may get all bits 1's. Handler can be called if the
interrupt request is shared with other peripherals or at the end of free_irq().
Therefore check the runtime suspended status before processing.
Fixes: cdf8259d65 ("can: m_can: Add PM Support")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20200915134715.696303-1-jarkko.nikula@linux.intel.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
