Jeff Johnson says:
==================
ath.git update for v6.17-rc5
Fix a long-standing issue with ath11k dropping group data packets
during GTK rekey, and fix an omission in the ath12k multi-link EMLSR
support introduced in v6.16.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During GTK rekey, mac80211 issues a clear key (if the old key exists)
followed by an install key operation in the same context. This causes
ath11k to send two WMI commands in quick succession: one to clear the
old key and another to install the new key in the same slot.
Under certain conditions—especially under high load or time sensitive
scenarios, firmware may process these commands asynchronously in a way
that firmware assumes the key is cleared whereas hardware has a valid key.
This inconsistency between hardware and firmware leads to group addressed
packet drops. Only setting the same key again can restore a valid key in
firmware and allow packets to be transmitted.
This issue remained latent because the host's clear key commands were
not effective in firmware until commit 436a4e8865 ("ath11k: clear the
keys properly via DISABLE_KEY"). That commit enabled the host to
explicitly clear group keys, which inadvertently exposed the race.
To mitigate this, restrict group key clearing across all modes (AP, STA,
MESH). During rekey, the new key can simply be set on top of the previous
one, avoiding the need for a clear followed by a set.
However, in AP mode specifically, permit group key clearing when no
stations are associated. This exception supports transitions from secure
modes (e.g., WPA2/WPA3) to open mode, during which all associated peers
are removed and the group key is cleared as part of the transition.
Add a per-BSS station counter to track the presence of stations during
set key operations. Also add a reset_group_keys flag to track the key
re-installation state and avoid repeated installation of the same key
when the number of connected stations transitions to non-zero within a
rekey period.
Additionally, for AP and Mesh modes, when the first station associates,
reinstall the same group key that was last set. This ensures that the
firmware recovers from any race that may have occurred during a previous
key clear when no stations were associated.
This change ensures that key clearing is permitted only when no clients
are connected, avoiding packet loss while enabling dynamic security mode
transitions.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.9.0.1-02146-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Reported-by: Steffen Moser <lists@steffen-moser.de>
Closes: https://lore.kernel.org/linux-wireless/c6366409-9928-4dd7-bf7b-ba7fcf20eabf@steffen-moser.de
Fixes: 436a4e8865 ("ath11k: clear the keys properly via DISABLE_KEY")
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250810170018.1124014-1-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, when updating EMLSR capabilities of a multi-link (ML) station,
only the EMLSR parameters (e.g., padding delay, transition delay, and
timeout) are sent to firmware. However, firmware also requires the
EMLSR support flag to be set in the MLO flags of the peer assoc WMI
command to properly handle EML operating mode notification frames.
Set the ATH12K_WMI_FLAG_MLO_EMLSR_SUPPORT flag in the peer assoc WMI
command when the ML station is EMLSR-capable, so that the firmware can
respond to EHT EML action frames from associated stations.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: 4bcf9525bc ("wifi: ath12k: update EMLSR capabilities of ML Station")
Signed-off-by: Ramya Gnanasekar <ramya.gnanasekar@oss.qualcomm.com>
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250801104920.3326352-1-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Miri Korenblit says:
====================
a few fixes, mainly of the cfg rework.
====================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The adapter->chan_stats[] array is initialized in
mwifiex_init_channel_scan_gap() with vmalloc(), which doesn't zero out
memory. The array is filled in mwifiex_update_chan_statistics()
and then the user can query the data in mwifiex_cfg80211_dump_survey().
There are two potential issues here. What if the user calls
mwifiex_cfg80211_dump_survey() before the data has been filled in.
Also the mwifiex_update_chan_statistics() function doesn't necessarily
initialize the whole array. Since the array was not initialized at
the start that could result in an information leak.
Also this array is pretty small. It's a maximum of 900 bytes so it's
more appropriate to use kcalloc() instead vmalloc().
Cc: stable@vger.kernel.org
Fixes: bf35443314 ("mwifiex: channel statistics support for mwifiex")
Suggested-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/20250815023055.477719-1-rongqianfeng@vivo.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since stations are recreated from scratch, all lists that wcids are added
to must be cleared before calling ieee80211_restart_hw.
Set wcid->sta = 0 for each wcid entry in order to ensure that they are
not added again before they are ready.
Fixes: 8a55712d12 ("wifi: mt76: mt7915: enable full system reset support")
Link: https://patch.msgid.link/20250827085352.51636-4-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Non-station wcid entries must not be passed to the rx functions.
In case of the global wcid entry, it could even lead to corruption in the wcid
array due to pointer being casted to struct mt7996_sta_link using container_of.
Fixes: 7464b12b7d ("wifi: mt76: mt7996: rework mt7996_rx_get_wcid to support MLO")
Link: https://patch.msgid.link/20250827085352.51636-3-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When a wcid can't be found, link_sta can be stale from a previous batch.
The code currently assumes that if link_sta is set, wcid is also non-zero.
Fix wcid NULL pointer dereference by resetting link_sta when a wcid entry
can't be found.
Fixes: 62da647a2b ("wifi: mt76: mt7996: Add MLO support to mt7996_tx_check_aggr()")
Link: https://patch.msgid.link/20250827085352.51636-1-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When station mode, don't disconnect when we get
channel switch from AP to DFS channel. Most APs
send CSA request after pass background CAC. In other
case we should disconnect after detect beacon miss.
Without patch when we get CSA to DFS channel get:
"kernel: wlo1: preparing for channel switch failed, disconnecting"
Fixes: 8aa2f59260 ("wifi: mt76: mt7921: introduce CSA support")
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Link: https://patch.msgid.link/20250716165443.28354-1-janusz.dziedzic@gmail.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A new warning in clang [1] points out a couple of places where a hdr
variable is not initialized then passed along to skb_put_data().
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:1894:21: warning: variable 'hdr' is uninitialized when passed as a const pointer argument here [-Wuninitialized-const-pointer]
1894 | skb_put_data(skb, &hdr, sizeof(hdr));
| ^~~
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:3386:21: warning: variable 'hdr' is uninitialized when passed as a const pointer argument here [-Wuninitialized-const-pointer]
3386 | skb_put_data(skb, &hdr, sizeof(hdr));
| ^~~
Zero initialize these headers as done in other places in the driver when
there is nothing stored in the header.
Cc: stable@vger.kernel.org
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Link: 00dacf8c22 [1]
Closes: https://github.com/ClangBuiltLinux/linux/issues/2104
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patch.msgid.link/20250715-mt7996-fix-uninit-const-pointer-v1-1-b5d8d11d7b78@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The brcmf_btcoex_detach() only shuts down the btcoex timer, if the
flag timer_on is false. However, the brcmf_btcoex_timerfunc(), which
runs as timer handler, sets timer_on to false. This creates critical
race conditions:
1.If brcmf_btcoex_detach() is called while brcmf_btcoex_timerfunc()
is executing, it may observe timer_on as false and skip the call to
timer_shutdown_sync().
2.The brcmf_btcoex_timerfunc() may then reschedule the brcmf_btcoex_info
worker after the cancel_work_sync() has been executed, resulting in
use-after-free bugs.
The use-after-free bugs occur in two distinct scenarios, depending on
the timing of when the brcmf_btcoex_info struct is freed relative to
the execution of its worker thread.
Scenario 1: Freed before the worker is scheduled
The brcmf_btcoex_info is deallocated before the worker is scheduled.
A race condition can occur when schedule_work(&bt_local->work) is
called after the target memory has been freed. The sequence of events
is detailed below:
CPU0 | CPU1
brcmf_btcoex_detach | brcmf_btcoex_timerfunc
| bt_local->timer_on = false;
if (cfg->btcoex->timer_on) |
... |
cancel_work_sync(); |
... |
kfree(cfg->btcoex); // FREE |
| schedule_work(&bt_local->work); // USE
Scenario 2: Freed after the worker is scheduled
The brcmf_btcoex_info is freed after the worker has been scheduled
but before or during its execution. In this case, statements within
the brcmf_btcoex_handler() — such as the container_of macro and
subsequent dereferences of the brcmf_btcoex_info object will cause
a use-after-free access. The following timeline illustrates this
scenario:
CPU0 | CPU1
brcmf_btcoex_detach | brcmf_btcoex_timerfunc
| bt_local->timer_on = false;
if (cfg->btcoex->timer_on) |
... |
cancel_work_sync(); |
... | schedule_work(); // Reschedule
|
kfree(cfg->btcoex); // FREE | brcmf_btcoex_handler() // Worker
/* | btci = container_of(....); // USE
The kfree() above could | ...
also occur at any point | btci-> // USE
during the worker's execution|
*/ |
To resolve the race conditions, drop the conditional check and call
timer_shutdown_sync() directly. It can deactivate the timer reliably,
regardless of its current state. Once stopped, the timer_on state is
then set to false.
Fixes: 61730d4dff ("brcmfmac: support critical protocol API for DHCP")
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://patch.msgid.link/20250822050839.4413-1-duoming@zju.edu.cn
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Compile-testing this driver on Arm platforms shows a link failure
when the CRC functions are not part of the kernel:
x86_64-linux-ld: drivers/net/wireless/ralink/rt2x00/rt2800lib.o: in function `rt2800_check_firmware':
rt2800lib.c:(.text+0x20e5): undefined reference to `crc_ccitt'
Move the select statement to the correct Kconfig symbol to match
the call site.
Fixes: 311b05e235 ("wifi: rt2x00: add COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://patch.msgid.link/20250731075837.1969136-1-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Wrap datapath globals into net_aligned_data, to avoid false sharing
- Preserve MSG_ZEROCOPY in forwarding (e.g. out of a container)
- Add SO_INQ and SCM_INQ support to AF_UNIX
- Add SIOCINQ support to AF_VSOCK
- Add TCP_MAXSEG sockopt to MPTCP
- Add IPv6 force_forwarding sysctl to enable forwarding per interface
- Make TCP validation of whether packet fully fits in the receive
window and the rcv_buf more strict. With increased use of HW
aggregation a single "packet" can be multiple 100s of kB
- Add MSG_MORE flag to optimize large TCP transmissions via sockmap,
improves latency up to 33% for sockmap users
- Convert TCP send queue handling from tasklet to BH workque
- Improve BPF iteration over TCP sockets to see each socket exactly
once
- Remove obsolete and unused TCP RFC3517/RFC6675 loss recovery code
- Support enabling kernel threads for NAPI processing on per-NAPI
instance basis rather than a whole device. Fully stop the kernel
NAPI thread when threaded NAPI gets disabled. Previously thread
would stick around until ifdown due to tricky synchronization
- Allow multicast routing to take effect on locally-generated packets
- Add output interface argument for End.X in segment routing
- MCTP: add support for gateway routing, improve bind() handling
- Don't require rtnl_lock when fetching an IPv6 neighbor over Netlink
- Add a new neighbor flag ("extern_valid"), which cedes refresh
responsibilities to userspace. This is needed for EVPN multi-homing
where a neighbor entry for a multi-homed host needs to be synced
across all the VTEPs among which the host is multi-homed
- Support NUD_PERMANENT for proxy neighbor entries
- Add a new queuing discipline for IETF RFC9332 DualQ Coupled AQM
- Add sequence numbers to netconsole messages. Unregister
netconsole's console when all net targets are removed. Code
refactoring. Add a number of selftests
- Align IPSec inbound SA lookup to RFC 4301. Only SPI and protocol
should be used for an inbound SA lookup
- Support inspecting ref_tracker state via DebugFS
- Don't force bonding advertisement frames tx to ~333 ms boundaries.
Add broadcast_neighbor option to send ARP/ND on all bonded links
- Allow providing upcall pid for the 'execute' command in openvswitch
- Remove DCCP support from Netfilter's conntrack
- Disallow multiple packet duplications in the queuing layer
- Prevent use of deprecated iptables code on PREEMPT_RT
Driver API:
- Support RSS and hashing configuration over ethtool Netlink
- Add dedicated ethtool callbacks for getting and setting hashing
fields
- Add support for power budget evaluation strategy in PSE /
Power-over-Ethernet. Generate Netlink events for overcurrent etc
- Support DPLL phase offset monitoring across all device inputs.
Support providing clock reference and SYNC over separate DPLL
inputs
- Support traffic classes in devlink rate API for bandwidth
management
- Remove rtnl_lock dependency from UDP tunnel port configuration
Device drivers:
- Add a new Broadcom driver for 800G Ethernet (bnge)
- Add a standalone driver for Microchip ZL3073x DPLL
- Remove IBM's NETIUCV device driver
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support zero-copy Tx of DMABUF memory
- take page size into account for page pool recycling rings
- Intel (100G, ice, idpf):
- idpf: XDP and AF_XDP support preparations
- idpf: add flow steering
- add link_down_events statistic
- clean up the TSPLL code
- preparations for live VM migration
- nVidia/Mellanox:
- support zero-copy Rx/Tx interfaces (DMABUF and io_uring)
- optimize context memory usage for matchers
- expose serial numbers in devlink info
- support PCIe congestion metrics
- Meta (fbnic):
- add 25G, 50G, and 100G link modes to phylink
- support dumping FW logs
- Marvell/Cavium:
- support for CN20K generation of the Octeon chips
- Amazon:
- add HW clock (without timestamping, just hypervisor time access)
- Ethernet virtual:
- VirtIO net:
- support segmentation of UDP-tunnel-encapsulated packets
- Google (gve):
- support packet timestamping and clock synchronization
- Microsoft vNIC:
- add handler for device-originated servicing events
- allow dynamic MSI-X vector allocation
- support Tx bandwidth clamping
- Ethernet NICs consumer, and embedded:
- AMD:
- amd-xgbe: hardware timestamping and PTP clock support
- Broadcom integrated MACs (bcmgenet, bcmasp):
- use napi_complete_done() return value to support NAPI polling
- add support for re-starting auto-negotiation
- Broadcom switches (b53):
- support BCM5325 switches
- add bcm63xx EPHY power control
- Synopsys (stmmac):
- lots of code refactoring and cleanups
- TI:
- icssg-prueth: read firmware-names from device tree
- icssg: PRP offload support
- Microchip:
- lan78xx: convert to PHYLINK for improved PHY and MAC management
- ksz: add KSZ8463 switch support
- Intel:
- support similar queue priority scheme in multi-queue and
time-sensitive networking (taprio)
- support packet pre-emption in both
- RealTek (r8169):
- enable EEE at 5Gbps on RTL8126
- Airoha:
- add PPPoE offload support
- MDIO bus controller for Airoha AN7583
- Ethernet PHYs:
- support for the IPQ5018 internal GE PHY
- micrel KSZ9477 switch-integrated PHYs:
- add MDI/MDI-X control support
- add RX error counters
- add cable test support
- add Signal Quality Indicator (SQI) reporting
- dp83tg720: improve reset handling and reduce link recovery time
- support bcm54811 (and its MII-Lite interface type)
- air_en8811h: support resume/suspend
- support PHY counters for QCA807x and QCA808x
- support WoL for QCA807x
- CAN drivers:
- rcar_canfd: support for Transceiver Delay Compensation
- kvaser: report FW versions via devlink dev info
- WiFi:
- extended regulatory info support (6 GHz)
- add statistics and beacon monitor for Multi-Link Operation (MLO)
- support S1G aggregation, improve S1G support
- add Radio Measurement action fields
- support per-radio RTS threshold
- some work around how FIPS affects wifi, which was wrong (RC4 is
used by TKIP, not only WEP)
- improvements for unsolicited probe response handling
- WiFi drivers:
- RealTek (rtw88):
- IBSS mode for SDIO devices
- RealTek (rtw89):
- BT coexistence for MLO/WiFi7
- concurrent station + P2P support
- support for USB devices RTL8851BU/RTL8852BU
- Intel (iwlwifi):
- use embedded PNVM in (to be released) FW images to fix
compatibility issues
- many cleanups (unused FW APIs, PCIe code, WoWLAN)
- some FIPS interoperability
- MediaTek (mt76):
- firmware recovery improvements
- more MLO work
- Qualcomm/Atheros (ath12k):
- fix scan on multi-radio devices
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- Broadcom (brcm80211):
- support SDIO 43751 device
- Bluetooth:
- hci_event: add support for handling LE BIG Sync Lost event
- ISO: add socket option to report packet seqnum via CMSG
- ISO: support SCM_TIMESTAMPING for ISO TS
- Bluetooth drivers:
- intel_pcie: support Function Level Reset
- nxpuart: add support for 4M baudrate
- nxpuart: implement powerup sequence, reset, FW dump, and FW loading"
* tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1742 commits)
dpll: zl3073x: Fix build failure
selftests: bpf: fix legacy netfilter options
ipv6: annotate data-races around rt->fib6_nsiblings
ipv6: fix possible infinite loop in fib6_info_uses_dev()
ipv6: prevent infinite loop in rt6_nlmsg_size()
ipv6: add a retry logic in net6_rt_notify()
vrf: Drop existing dst reference in vrf_ip6_input_dst
net/sched: taprio: align entry index attr validation with mqprio
net: fsl_pq_mdio: use dev_err_probe
selftests: rtnetlink.sh: remove esp4_offload after test
vsock: remove unnecessary null check in vsock_getname()
igb: xsk: solve negative overflow of nb_pkts in zerocopy mode
stmmac: xsk: fix negative overflow of budget in zerocopy mode
dt-bindings: ieee802154: Convert at86rf230.txt yaml format
net: dsa: microchip: Disable PTP function of KSZ8463
net: dsa: microchip: Setup fiber ports for KSZ8463
net: dsa: microchip: Write switch MAC address differently for KSZ8463
net: dsa: microchip: Use different registers for KSZ8463
net: dsa: microchip: Add KSZ8463 switch support to KSZ DSA driver
dt-bindings: net: dsa: microchip: Add KSZ8463 switch support
...
Pull driver core updates from Danilo Krummrich:
"debugfs:
- Remove unneeded debugfs_file_{get,put}() instances
- Remove last remnants of debugfs_real_fops()
- Allow storing non-const void * in struct debugfs_inode_info::aux
sysfs:
- Switch back to attribute_group::bin_attrs (treewide)
- Switch back to bin_attribute::read()/write() (treewide)
- Constify internal references to 'struct bin_attribute'
Support cache-ids for device-tree systems:
- Add arch hook arch_compact_of_hwid()
- Use arch_compact_of_hwid() to compact MPIDR values on arm64
Rust:
- Device:
- Introduce CoreInternal device context (for bus internal methods)
- Provide generic drvdata accessors for bus devices
- Provide Driver::unbind() callbacks
- Use the infrastructure above for auxiliary, PCI and platform
- Implement Device::as_bound()
- Rename Device::as_ref() to Device::from_raw() (treewide)
- Implement fwnode and device property abstractions
- Implement example usage in the Rust platform sample driver
- Devres:
- Remove the inner reference count (Arc) and use pin-init instead
- Replace Devres::new_foreign_owned() with devres::register()
- Require T to be Send in Devres<T>
- Initialize the data kept inside a Devres last
- Provide an accessor for the Devres associated Device
- Device ID:
- Add support for ACPI device IDs and driver match tables
- Split up generic device ID infrastructure
- Use generic device ID infrastructure in net::phy
- DMA:
- Implement the dma::Device trait
- Add DMA mask accessors to dma::Device
- Implement dma::Device for PCI and platform devices
- Use DMA masks from the DMA sample module
- I/O:
- Implement abstraction for resource regions (struct resource)
- Implement resource-based ioremap() abstractions
- Provide platform device accessors for I/O (remap) requests
- Misc:
- Support fallible PinInit types in Revocable
- Implement Wrapper<T> for Opaque<T>
- Merge pin-init blanket dependencies (for Devres)
Misc:
- Fix OF node leak in auxiliary_device_create()
- Use util macros in device property iterators
- Improve kobject sample code
- Add device_link_test() for testing device link flags
- Fix typo in Documentation/ABI/testing/sysfs-kernel-address_bits
- Hint to prefer container_of_const() over container_of()"
* tag 'driver-core-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core: (84 commits)
rust: io: fix broken intra-doc links to `platform::Device`
rust: io: fix broken intra-doc link to missing `flags` module
rust: io: mem: enable IoRequest doc-tests
rust: platform: add resource accessors
rust: io: mem: add a generic iomem abstraction
rust: io: add resource abstraction
rust: samples: dma: set DMA mask
rust: platform: implement the `dma::Device` trait
rust: pci: implement the `dma::Device` trait
rust: dma: add DMA addressing capabilities
rust: dma: implement `dma::Device` trait
rust: net::phy Change module_phy_driver macro to use module_device_table macro
rust: net::phy represent DeviceId as transparent wrapper over mdio_device_id
rust: device_id: split out index support into a separate trait
device: rust: rename Device::as_ref() to Device::from_raw()
arm64: cacheinfo: Provide helper to compress MPIDR value into u32
cacheinfo: Add arch hook to compress CPU h/w id into 32 bits for cache-id
cacheinfo: Set cache 'id' based on DT data
container_of: Document container_of() is not to be used in new code
driver core: auxiliary bus: fix OF node leak
...
Prepare for adding an enum type for NAPI threaded states by adding
netif_threaded_enable API. De-export the existing netif_set_threaded API
and only use it internally. Update existing drivers to use
netif_threaded_enable instead of the de-exported netif_set_threaded.
Note that dev_set_threaded used by mt76 debugfs file is unchanged.
Signed-off-by: Samiullah Khawaja <skhawaja@google.com>
Link: https://patch.msgid.link/20250723013031.2911384-3-skhawaja@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Johannes Berg says:
====================
Another wireless update:
- rtw89:
- STA+P2P concurrency
- support for USB devices RTL8851BU/RTL8852BU
- ath9k: OF support
- ath12k:
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- iwlwifi: some FIPS interoperability
- brcm80211: support SDIO 43751 device
- rt2x00: better DT/OF support
- cfg80211/mac80211:
- improved S1G support
- beacon monitor for MLO
* tag 'wireless-next-2025-07-24' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (199 commits)
ssb: use new GPIO line value setter callbacks for the second GPIO chip
wifi: Fix typos
wifi: brcmsmac: Use str_true_false() helper
wifi: brcmfmac: fix EXTSAE WPA3 connection failure due to AUTH TX failure
wifi: brcm80211: Remove yet more unused functions
wifi: brcm80211: Remove more unused functions
wifi: brcm80211: Remove unused functions
wifi: iwlwifi: Revert "wifi: iwlwifi: remove support of several iwl_ppag_table_cmd versions"
wifi: iwlwifi: check validity of the FW API range
wifi: iwlwifi: don't export symbols that we shouldn't
wifi: iwlwifi: mld: use spec link id and not FW link id
wifi: iwlwifi: mld: decode EOF bit for AMPDUs
wifi: iwlwifi: Remove support for rx OMI bandwidth reduction
wifi: iwlwifi: stop supporting iwl_omi_send_status_notif ver 1
wifi: iwlwifi: remove SC2F firmware support
wifi: iwlwifi: mvm: Remove NAN support
wifi: iwlwifi: mld: avoid outdated reorder buffer head_sn
wifi: iwlwifi: mvm: avoid outdated reorder buffer head_sn
wifi: iwlwifi: disable certain features for fips_enabled
wifi: iwlwifi: mld: support channel survey collection for ACS scans
...
====================
Link: https://patch.msgid.link/20250724100349.21564-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Miri Korenblit says:
====================
iwlwifi feature, notably
- disable features in fips
- remove RX OMI feature code
- A few fixes and cleanups
====================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For WPA3-SAE Connection in EXTSAE mode, the userspace daemon is allowed to
generate the SAE Auth frames. The driver uses the "mgmt_frame" FW IOVAR to
transmit this MGMT frame.
Before sending the IOVAR, the Driver is incorrectly treating the channel
number read from the FW as a frequency value and again attempts to convert
this into a channel number using ieee80211_frequency_to_channel().
This added an invalid channel number as part of the IOVAR request to the FW
And some FW which strictly expects a valid channel would return BAD_CHAN
error, while failing to transmit the driver requested SAE Auth MGMT frame.
Fix this in the CYW vendor specific MGMT TX cfg80211 ops handler, by not
treating the channel number read from the FW as frequency value and skip
the attempt to convert it again into a channel number.
Also fix this in the generic MGMT TX cfg80211 ops handler.
Fixes: c2ff8cad64 ("brcm80211: make mgmt_tx in brcmfmac accept a NULL channel")
Fixes: 66f909308a ("wifi: brcmfmac: cyw: support external SAE authentication in station mode")
Signed-off-by: Ting-Ying Li <tingying.li@cypress.com>
Signed-off-by: Gokul Sivakumar <gokulkumar.sivakumar@infineon.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>>
Link: https://patch.msgid.link/20250723105918.5229-1-gokulkumar.sivakumar@infineon.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
