Added transceiver type, speed capability and board types
in HSI, are utilizing to display the accurate link
information in ethtool.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update parsing of route dump request to enable kernel side filtering.
Allow filtering results by protocol (e.g., which routing daemon installed
the route), route type (e.g., unicast), table id and nexthop device. These
amount to the low hanging fruit, yet a huge improvement, for dumping
routes.
ip_valid_fib_dump_req is called with RTNL held, so __dev_get_by_index can
be used to look up the device index without taking a reference. From
there filter->dev is only used during dump loops with the lock still held.
Set NLM_F_DUMP_FILTERED in the answer_flags so the user knows the results
have been filtered should no entries be returned.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement kernel side filtering of routes by egress device index and
table id. If the table id is given in the filter, lookup table and
call mr_table_dump directly for it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move per-table loops from mr_rtm_dumproute to mr_table_dump and export
mr_table_dump for dumps by specific table id.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement kernel side filtering of routes by table id, egress device index,
protocol and route type. If the table id is given in the filter, lookup the
table and call fib_table_dump directly for it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add struct fib_dump_filter for options on limiting which routes are
returned in a dump request. The current list is table id, protocol,
route type, rtm_flags and nexthop device index. struct net is needed
to lookup the net_device from the index.
Declare the filter for each route dump handler and plumb the new
arguments from dump handlers to ip_valid_fib_dump_req.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With dump filtering we need a way to ensure the NLM_F_DUMP_FILTERED
flag is set on a message back to the user if the data returned is
influenced by some input attributes. Normally this can be done as
messages are added to the skb, but if the filter results in no data
being returned, the user could be confused as to why.
This patch adds answer_flags to the netlink_callback allowing dump
handlers to set the NLM_F_DUMP_FILTERED at a minimum in the
NLMSG_DONE message ensuring the flag gets back to the user.
The netlink_callback space is initialized to 0 via a memset in
__netlink_dump_start, so init of the new answer_flags is covered.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-10-16
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Convert BPF sockmap and kTLS to both use a new sk_msg API and enable
sk_msg BPF integration for the latter, from Daniel and John.
2) Enable BPF syscall side to indicate for maps that they do not support
a map lookup operation as opposed to just missing key, from Prashant.
3) Add bpftool map create command which after map creation pins the
map into bpf fs for further processing, from Jakub.
4) Add bpftool support for attaching programs to maps allowing sock_map
and sock_hash to be used from bpftool, from John.
5) Improve syscall BPF map update/delete path for map-in-map types to
wait a RCU grace period for pending references to complete, from Daniel.
6) Couple of follow-up fixes for the BPF socket lookup to get it
enabled also when IPv6 is compiled as a module, from Joe.
7) Fix a generic-XDP bug to handle the case when the Ethernet header
was mangled and thus update skb's protocol and data, from Jesper.
8) Add a missing BTF header length check between header copies from
user space, from Wenwen.
9) Minor fixups in libbpf to use __u32 instead u32 types and include
proper perf_event.h uapi header instead of perf internal one, from Yonghong.
10) Allow to pass user-defined flags through EXTRA_CFLAGS and EXTRA_LDFLAGS
to bpftool's build, from Jiri.
11) BPF kselftest tweaks to add LWTUNNEL to config fragment and to install
with_addr.sh script from flow dissector selftest, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_pacing_rate has beed introduced as a u32 field in 2013,
effectively limiting per flow pacing to 34Gbit.
We believe it is time to allow TCP to pace high speed flows
on 64bit hosts, as we now can reach 100Gbit on one TCP flow.
This patch adds no cost for 32bit kernels.
The tcpi_pacing_rate and tcpi_max_pacing_rate were already
exported as 64bit, so iproute2/ss command require no changes.
Unfortunately the SO_MAX_PACING_RATE socket option will stay
32bit and we will need to add a new option to let applications
control high pacing rates.
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 1787144 10.246.9.76:49992 10.246.9.77:36741
timer:(on,003ms,0) ino:91863 sk:2 <->
skmem:(r0,rb540000,t66440,tb2363904,f605944,w1822984,o0,bl0,d0)
ts sack bbr wscale:8,8 rto:201 rtt:0.057/0.006 mss:1448
rcvmss:536 advmss:1448
cwnd:138 ssthresh:178 bytes_acked:256699822585 segs_out:177279177
segs_in:3916318 data_segs_out:177279175
bbr:(bw:31276.8Mbps,mrtt:0,pacing_gain:1.25,cwnd_gain:2)
send 28045.5Mbps lastrcv:73333
pacing_rate 38705.0Mbps delivery_rate 22997.6Mbps
busy:73333ms unacked:135 retrans:0/157 rcv_space:14480
notsent:2085120 minrtt:0.013
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In EDT design, I made the mistake of using tcp_wstamp_ns
to store the last tcp_clock_ns() sample and to store the
pacing virtual timer.
This causes major regressions at high speed flows.
Introduce tcp_clock_cache to store last tcp_clock_ns().
This is needed because some arches have slow high-resolution
kernel time service.
tcp_wstamp_ns is only updated when a packet is sent.
Note that we can remove tcp_mstamp in the future since
tcp_mstamp is essentially tcp_clock_cache/1000, so the
apparent socket size increase is temporary.
Fixes: 9799ccb0e9 ("tcp: add tcp_wstamp_ns socket field")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new command (NCSI_CMD_SEND_CMD) is added to allow user space application
to send NC-SI command to the network card.
Also, add a new attribute (NCSI_ATTR_DATA) for transferring request and response.
The work flow is as below.
Request:
User space application
-> Netlink interface (msg)
-> new Netlink handler - ncsi_send_cmd_nl()
-> ncsi_xmit_cmd()
Response:
Response received - ncsi_rcv_rsp()
-> internal response handler - ncsi_rsp_handler_xxx()
-> ncsi_rsp_handler_netlink()
-> ncsi_send_netlink_rsp ()
-> Netlink interface (msg)
-> user space application
Command timeout - ncsi_request_timeout()
-> ncsi_send_netlink_timeout ()
-> Netlink interface (msg with zero data length)
-> user space application
Error:
Error detected
-> ncsi_send_netlink_err ()
-> Netlink interface (err msg)
-> user space application
Signed-off-by: Justin Lee <justin.lee1@dell.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5e-updates-2018-10-10
IPoIB netlink support and mlx5e pre-allocated netdevice initialization
IP link was broken due to the changes in IPoIB for the rdma_netdev
support after commit cd565b4b51
("IB/IPoIB: Support acceleration options callbacks").
This patchset fixes IPoIB pkey creation and removal using rtnetlink by
adding support in both IPoIB ULP layer and mlx5 layer:
From Jason and Denis:
1) Introduces changes in the RDMA netdev code in order to
allow allocation of the netdev to be done by the rtnl netdev code.
2) Reworks IPoIB initialization to use the two step rdma_netdev
creation.
From Feras and Saeed, mlx5e netdev layer refactoring to allow accepting
pre-allocated netdevs:
3) Adds support to initialize/cleanup netdevs that are not created
by mlx5 driver.
4) Change mlx5e netdevice layer to accept the pre-allocated netdevice
queue number.
5) Initialize mlx5e generic structures in one place to be used for all
netdevs types NIC/representors/IPoIB (both mlx5 allocated and
pre-allocted).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
DEC FDDIcontroller 700 (DEFZA) uses a Tx/Rx queue pair to communicate
SMT frames with adapter's firmware. Any SMT frame received from the RMC
via the Rx queue is queued back by the driver to the SMT Rx queue for
the firmware to process. Similarly the firmware uses the SMT Tx queue
to supply the driver with SMT frames which are queued back to the Tx
queue for the RMC to send to the ring.
When a network tap is attached to an FDDI interface handled by `defza'
any incoming SMT frames captured are queued to our usual processing of
network data received, which in turn delivers them to any listening
taps.
However the outgoing SMT frames produced by the firmware bypass our
network protocol stack and are therefore not delivered to taps. This in
turn means that taps are missing a part of network traffic sent by the
adapter, which may make it more difficult to track down network problems
or do general traffic analysis.
Call `dev_queue_xmit_nit' then in the SMT Tx path, having checked that
a network tap is attached, with a newly-created `dev_nit_active' helper
wrapping the usual condition used in the transmit path.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the DEC FDDIcontroller 700 (DEFZA), Digital Equipment
Corporation's first-generation FDDI network interface adapter, made for
TURBOchannel and based on a discrete version of what eventually became
Motorola's widely used CAMEL chipset.
The CAMEL chipset is present for example in the DEC FDDIcontroller
TURBOchannel, EISA and PCI adapters (DEFTA/DEFEA/DEFPA) that we support
with the `defxx' driver, however the host bus interface logic and the
firmware API are different in the DEFZA and hence a separate driver is
required.
There isn't much to say about the driver except that it works, but there
is one peculiarity to mention. The adapter implements two Tx/Rx queue
pairs.
Of these one pair is the usual network Tx/Rx queue pair, in this case
used by the adapter to exchange frames with the ring, via the RMC (Ring
Memory Controller) chip. The Tx queue is handled directly by the RMC
chip and resides in onboard packet memory. The Rx queue is maintained
via DMA in host memory by adapter's firmware copying received data
stored by the RMC in onboard packet memory.
The other pair is used to communicate SMT frames with adapter's
firmware. Any SMT frame received from the RMC via the Rx queue must be
queued back by the driver to the SMT Rx queue for the firmware to
process. Similarly the firmware uses the SMT Tx queue to supply the
driver with SMT frames that must be queued back to the Tx queue for the
RMC to send to the ring.
This solution was chosen because the designers ran out of PCB space and
could not squeeze in more logic onto the board that would be required to
handle this SMT frame traffic without the need to involve the driver, as
with the later DEFTA/DEFEA/DEFPA adapters.
Finally the driver does some Frame Control byte decoding, so to avoid
magic numbers some macros are added to <linux/if_fddi.h>.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a more complete fix than d71019b54b ("net: core: Fix build
with CONFIG_IPV6=m"), so that IPv6 sockets may be looked up if the IPv6
module is loaded (not just if it's compiled in).
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This work adds BPF sk_msg verdict program support to kTLS
allowing BPF and kTLS to be combined together. Previously kTLS
and sk_msg verdict programs were mutually exclusive in the
ULP layer which created challenges for the orchestrator when
trying to apply TCP based policy, for example. To resolve this,
leveraging the work from previous patches that consolidates
the use of sk_msg, we can finally enable BPF sk_msg verdict
programs so they continue to run after the kTLS socket is
created. No change in behavior when kTLS is not used in
combination with BPF, the kselftest suite for kTLS also runs
successfully.
Joint work with Daniel.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Instead of re-implementing poll routine use the poll callback to
trigger read from kTLS, we reuse the stream_memory_read callback
which is simpler and achieves the same. This helps to align sockmap
and kTLS so we can more easily embed BPF in kTLS.
Joint work with Daniel.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Convert kTLS over to make use of sk_msg interface for plaintext and
encrypted scattergather data, so it reuses all the sk_msg helpers
and data structure which later on in a second step enables to glue
this to BPF.
This also allows to remove quite a bit of open coded helpers which
are covered by the sk_msg API. Recent changes in kTLs 80ece6a03a
("tls: Remove redundant vars from tls record structure") and
4e6d47206c ("tls: Add support for inplace records encryption")
changed the data path handling a bit; while we've kept the latter
optimization intact, we had to undo the former change to better
fit the sk_msg model, hence the sg_aead_in and sg_aead_out have
been brought back and are linked into the sk_msg sgs. Now the kTLS
record contains a msg_plaintext and msg_encrypted sk_msg each.
In the original code, the zerocopy_from_iter() has been used out
of TX but also RX path. For the strparser skb-based RX path,
we've left the zerocopy_from_iter() in decrypt_internal() mostly
untouched, meaning it has been moved into tls_setup_from_iter()
with charging logic removed (as not used from RX). Given RX path
is not based on sk_msg objects, we haven't pursued setting up a
dummy sk_msg to call into sk_msg_zerocopy_from_iter(), but it
could be an option to prusue in a later step.
Joint work with John.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add a generic sk_msg layer, and convert current sockmap and later
kTLS over to make use of it. While sk_buff handles network packet
representation from netdevice up to socket, sk_msg handles data
representation from application to socket layer.
This means that sk_msg framework spans across ULP users in the
kernel, and enables features such as introspection or filtering
of data with the help of BPF programs that operate on this data
structure.
Latter becomes in particular useful for kTLS where data encryption
is deferred into the kernel, and as such enabling the kernel to
perform L7 introspection and policy based on BPF for TLS connections
where the record is being encrypted after BPF has run and came to
a verdict. In order to get there, first step is to transform open
coding of scatter-gather list handling into a common core framework
that subsystems can use.
The code itself has been split and refactored into three bigger
pieces: i) the generic sk_msg API which deals with managing the
scatter gather ring, providing helpers for walking and mangling,
transferring application data from user space into it, and preparing
it for BPF pre/post-processing, ii) the plain sock map itself
where sockets can be attached to or detached from; these bits
are independent of i) which can now be used also without sock
map, and iii) the integration with plain TCP as one protocol
to be used for processing L7 application data (later this could
e.g. also be extended to other protocols like UDP). The semantics
are the same with the old sock map code and therefore no change
of user facing behavior or APIs. While pursuing this work it
also helped finding a number of bugs in the old sockmap code
that we've fixed already in earlier commits. The test_sockmap
kselftest suite passes through fine as well.
Joint work with John.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In order to prepare sockmap logic to be used in combination with kTLS
we need to detangle it from ULP, and further split it in later commits
into a generic API.
Joint work with John.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have BUILD_BUG_ON_ZERO() which I just hadn't found
before, so we should use it here instead of open-coding another
implementation thereof.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
Highlights:
* merge net-next, so I can finish the hwsim workqueue removal
* fix TXQ NULL pointer issue that was reported multiple times
* minstrel cleanups from Felix
* simplify lib80211 code by not using skcipher, note that this
will conflict with the crypto tree (and this new code here
should be used)
* use new netlink policy validation in nl80211
* fix up SAE (part of WPA3) in client-mode
* FTM responder support in the stack
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an option to have per-port vlan stats instead of the
default global stats. The option can be set only when there are no port
vlans in the bridge since we need to allocate the stats if it is set
when vlans are being added to ports (and respectively free them
when being deleted). Also bump RTNL_MAX_TYPE as the bridge is the
largest user of options. The current stats design allows us to add
these without any changes to the fast-path, it all comes down to
the per-vlan stats pointer which, if this option is enabled, will
be allocated for each port vlan instead of using the global bridge-wide
one.
CC: bridge@lists.linux-foundation.org
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link's carrier goes down it could be a sign of the port changing
networks. If the new network has overlapping addresses with the old one,
then the kernel will continue trying to use neighbor entries established
based on the old network until the entries finally age out - meaning a
potentially long delay with communications not working.
This patch evicts neighbor entries on carrier down with the exception of
those marked permanent. Permanent entries are managed by userspace (either
an admin or a routing daemon such as FRR).
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another difference between IPv4 and IPv6 is the generation of RTM_DELROUTE
notifications when a device is taken down (admin down) or deleted. IPv4
does not generate a message for routes evicted by the down or delete;
IPv6 does. A NOS at scale really needs to avoid these messages and have
IPv4 and IPv6 behave similarly, relying on userspace to handle link
notifications and evict the routes.
At this point existing user behavior needs to be preserved. Since
notifications are a global action (not per app) the only way to preserve
existing behavior and allow the messages to be skipped is to add a new
sysctl (net/ipv6/route/skip_notify_on_dev_down) which can be set to
disable the notificatioons.
IPv6 route code already supports the option to skip the message (it is
used for multipath routes for example). Besides the new sysctl we need
to pass the skip_notify setting through the generic fib6_clean and
fib6_walk functions to fib6_clean_node and to set skip_notify on calls
to __ip_del_rt for the addrconf_ifdown path.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd writes:
"ARM: SoC fixes for 4.19
Two last minute bugfixes, both for NXP platforms:
* The Layerscape 'qbman' infrastructure suffers from probe ordering
bugs in some configurations, a two-patch series adds a hotfix for
this. 4.20 will have a longer set of patches to rework it.
* The old imx53-qsb board regressed in 4.19 after the addition
of cpufreq support, adding a set of explicit operating points
fixes this."
* tag 'armsoc-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
soc: fsl: qman_portals: defer probe after qman's probe
soc: fsl: qbman: add APIs to retrieve the probing status
ARM: dts: imx53-qsb: disable 1.2GHz OPP
Current mac80211 has provision to update tx status through
ieee80211_tx_status() and ieee80211_tx_status_ext(). But
drivers like ath10k updates the tx status from the skb except
txrate, txrate will be updated from a different path, peer stats.
Using ieee80211_tx_status_ext() in two different paths
(one for the stats, one for the tx rate) would duplicate
the stats instead.
To avoid this stats duplication, ieee80211_tx_rate_update()
is implemented.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
[minor commit message editing, use initializers in code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for drivers to report the total number of MPDUs received
and the number of MPDUs received with an FCS error from a specific
peer. These counters will be incremented only when the TA of the
frame matches the MAC address of the peer irrespective of FCS
error.
It should be noted that the TA field in the frame might be corrupted
when there is an FCS error and TA matching logic would fail in such
cases. Hence, FCS error counter might not be fully accurate, but it can
provide help in detecting bad RX links in significant number of cases.
This FCS error counter without full accuracy can be used, e.g., to
trigger a kick-out of a connected client with a bad link in AP mode to
force such a client to roam to another AP.
Signed-off-by: Ankita Bajaj <bankita@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Linus writes:
"GPIO fix for the v4.19 series:
- Fix up the interrupt parent for the irqdomains."
* tag 'gpio-v4.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Assign gpio_irq_chip::parents to non-stack pointer
New bss param ftm_responder is used to notify the driver to
enable fine timing request (FTM) responder role in AP mode.
Plumb the new cfg80211 API for FTM responder statistics through to
the driver API in mac80211.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Dmitry writes:
"Input updates for v4.19-rc7
- we added a few scheduling points into various input interfaces to
ensure that large writes will not cause RCU stalls
- fixed configuring PS/2 keyboards as wakeup devices on newer
platforms
- added a new Xbox gamepad ID."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: uinput - add a schedule point in uinput_inject_events()
Input: evdev - add a schedule point in evdev_write()
Input: mousedev - add a schedule point in mousedev_write()
Input: i8042 - enable keyboard wakeups by default when s2idle is used
Input: xpad - add support for Xbox1 PDP Camo series gamepad
Stephen writes:
"A couple of warning fixes:
Two fixes from Peter Oberparleiter <oberpar@linux.ibm.com>:
Commit 6b7dca401c ("tracing: Allow gcov profiling on only ftrace subsystem")
uncovered linker problems when using gcov kernel profiling on some
architectures. These problems were likely introduced earlier, and are
possibly related to compiler changes."
* tag 'next-fixes-20181012' of git://git.kernel.org/pub/scm/linux/kernel/git/sfr/next-fixes:
vmlinux.lds.h: Fix linker warnings about orphan .LPBX sections
vmlinux.lds.h: Fix incomplete .text.exit discards
David writes:
"Networking
1) RXRPC receive path fixes from David Howells.
2) Re-export __skb_recv_udp(), from Jiri Kosina.
3) Fix refcounting in u32 classificer, from Al Viro.
4) Userspace netlink ABI fixes from Eugene Syromiatnikov.
5) Don't double iounmap on rmmod in ena driver, from Arthur
Kiyanovski.
6) Fix devlink string attribute handling, we must pull a copy into a
kernel buffer if the lifetime extends past the netlink request.
From Moshe Shemesh.
7) Fix hangs in RDS, from Ka-Cheong Poon.
8) Fix recursive locking lockdep warnings in tipc, from Ying Xue.
9) Clear RX irq correctly in socionext, from Ilias Apalodimas.
10) bcm_sf2 fixes from Florian Fainelli."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
net: dsa: bcm_sf2: Call setup during switch resume
net: dsa: bcm_sf2: Fix unbind ordering
net: phy: sfp: remove sfp_mutex's definition
r8169: set RX_MULTI_EN bit in RxConfig for 8168F-family chips
net: socionext: clear rx irq correctly
net/mlx4_core: Fix warnings during boot on driverinit param set failures
tipc: eliminate possible recursive locking detected by LOCKDEP
selftests: udpgso_bench.sh explicitly requires bash
selftests: rtnetlink.sh explicitly requires bash.
qmi_wwan: Added support for Gemalto's Cinterion ALASxx WWAN interface
tipc: queue socket protocol error messages into socket receive buffer
tipc: set link tolerance correctly in broadcast link
net: ipv4: don't let PMTU updates increase route MTU
net: ipv4: update fnhe_pmtu when first hop's MTU changes
net/ipv6: stop leaking percpu memory in fib6 info
rds: RDS (tcp) hangs on sendto() to unresponding address
net: make skb_partial_csum_set() more robust against overflows
devlink: Add helper function for safely copy string param
devlink: Fix param cmode driverinit for string type
devlink: Fix param set handling for string type
...
Enabling both CONFIG_LD_DEAD_CODE_DATA_ELIMINATION=y and
CONFIG_GCOV_PROFILE_ALL=y results in linker warnings:
warning: orphan section `.data..LPBX1' being placed in
section `.data..LPBX1'.
LD_DEAD_CODE_DATA_ELIMINATION adds compiler flag -fdata-sections. This
option causes GCC to create separate data sections for data objects,
including those generated by GCC internally for gcov profiling. The
names of these objects start with a dot (.LPBX0, .LPBX1), resulting in
section names starting with 'data..'.
As section names starting with 'data..' are used for specific purposes
in the Linux kernel, the linker script does not automatically include
them in the output data section, resulting in the "orphan section"
linker warnings.
Fix this by specifically including sections named "data..LPBX*" in the
data section.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Enabling CONFIG_GCOV_PROFILE_ALL=y causes linker errors on ARM:
`.text.exit' referenced in section `.ARM.exidx.text.exit':
defined in discarded section `.text.exit'
`.text.exit' referenced in section `.fini_array.00100':
defined in discarded section `.text.exit'
And related errors on NDS32:
`.text.exit' referenced in section `.dtors.65435':
defined in discarded section `.text.exit'
The gcov compiler flags cause certain compiler versions to generate
additional destructor-related sections that are not yet handled by the
linker script, resulting in references between discarded and
non-discarded sections.
Since destructors are not used in the Linux kernel, fix this by
discarding these additional sections.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Greentime Hu <green.hu@gmail.com>
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tejun writes:
"cgroup fixes for v4.19-rc7
One cgroup2 threaded mode fix for v4.19-rc7. While threaded mode
isn't used widely (yet) and the bug requires somewhat convoluted
sequence of operations, it causes a userland visible malfunction -
EINVAL on a valid attempt to enable threaded mode. This pull request
contains the fix"
* 'for-4.19-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: Fix dom_cgrp propagation when enabling threaded mode
Since commit 5aad1de5ea ("ipv4: use separate genid for next hop
exceptions"), exceptions get deprecated separately from cached
routes. In particular, administrative changes don't clear PMTU anymore.
As Stefano described in commit e9fa1495d7 ("ipv6: Reflect MTU changes
on PMTU of exceptions for MTU-less routes"), the PMTU discovered before
the local MTU change can become stale:
- if the local MTU is now lower than the PMTU, that PMTU is now
incorrect
- if the local MTU was the lowest value in the path, and is increased,
we might discover a higher PMTU
Similarly to what commit e9fa1495d7 did for IPv6, update PMTU in those
cases.
If the exception was locked, the discovered PMTU was smaller than the
minimal accepted PMTU. In that case, if the new local MTU is smaller
than the current PMTU, let PMTU discovery figure out if locking of the
exception is still needed.
To do this, we need to know the old link MTU in the NETDEV_CHANGEMTU
notifier. By the time the notifier is called, dev->mtu has been
changed. This patch adds the old MTU as additional information in the
notifier structure, and a new call_netdevice_notifiers_u32() function.
Fixes: 5aad1de5ea ("ipv4: use separate genid for next hop exceptions")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells says:
====================
rxrpc: Fix packet reception code
Here are a set of patches that prepares for and fix problems in rxrpc's
package reception code. There serious problems are:
(A) There's a window between binding the socket and setting the data_ready
hook in which packets can find their way into the UDP socket's receive
queues.
(B) The skb_recv_udp() will return an error (and clear the error state) if
there was an error on the Tx side. rxrpc doesn't handle this.
(C) The rxrpc data_ready handler doesn't fully drain the UDP receive
queue.
(D) The rxrpc data_ready handler assumes it is called in a non-reentrant
state.
The second patch fixes (A) - (C); the third patch renders (B) and (C)
non-issues by using the recap_rcv hook instead of data_ready - and the
final patch fixes (D). That last is the most complex.
The preparatory patches are:
(1) Fix some places that are doing things in the wrong net namespace.
(2) Stop taking the rcu read lock as it's held by the IP input routine in
the call chain.
(3) Only end the Tx phase if *we* rotated the final packet out of the Tx
buffer.
(4) Don't assume that the call state won't change after dropping the
call_state lock.
(5) Only take receive window and MTU suze parameters from an ACK packet if
it's the latest ACK packet.
(6) Record connection-level abort information correctly.
(7) Fix a trace line.
And then there are three main patches - note that these are mixed in with
the preparatory patches somewhat:
(1) Fix the setup window (A), skb_recv_udp() error check (B) and packet
drainage (C).
(2) Switch to using the encap_rcv instead of data_ready to cut out the
effects of the UDP read queues and get the packets delivered directly.
(3) Add more locking into the various packet input paths to defend against
re-entrance (D).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_route_table_template is exported but there are no users outside
of route.c. Make it static.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPoIB netlink support was broken by the below commit since integrating
the rdma_netdev support relies on an allocation flow for netdevs that
was controlled by the ipoib driver while netdev's rtnl_newlink
implementation assumes that the netdev will be allocated by netlink.
Such situation leads to crash in __ipoib_device_add, once trying to
reuse netlink device.
This patch fixes the kernel oops for both mlx4 and mlx5
devices triggered by the following command:
Fixes: cd565b4b51 ("IB/IPoIB: Support acceleration options callbacks")
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
netdev has several interfaces that expect to call alloc_netdev_mqs from
the core code, with the driver only providing the arguments. This is
incompatible with the rdma_netdev interface that returns the netdev
directly.
Thus re-organize the API used by ipoib so that the verbs core code calls
alloc_netdev_mqs for the driver. This is done by allowing the drivers to
provide the allocation parameters via a 'get_params' callback and then
initializing an allocated netdev as a second step.
Fixes: cd565b4b51 ("IB/IPoIB: Support acceleration options callbacks")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Devlink string param buffer is allocated at the size of
DEVLINK_PARAM_MAX_STRING_VALUE. Add helper function which makes sure
this size is not exceeded.
Renamed DEVLINK_PARAM_MAX_STRING_VALUE to
__DEVLINK_PARAM_MAX_STRING_VALUE to emphasize that it should be used by
devlink only. The driver should use the helper function instead to
verify it doesn't exceed the allowed length.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case devlink param type is string, it needs to copy the string value
it got from the input to devlink_param_value.
Fixes: e3b7ca18ad ("devlink: Add param set command")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gpiochip_set_cascaded_irqchip() is passed 'parent_irq' as an argument
and then the address of that argument is assigned to the gpio chips
gpio_irq_chip 'parents' pointer shortly thereafter. This can't ever
work, because we've just assigned some stack address to a pointer that
we plan to dereference later in gpiochip_irq_map(). I ran into this
issue with the KASAN report below when gpiochip_irq_map() tried to setup
the parent irq with a total junk pointer for the 'parents' array.
BUG: KASAN: stack-out-of-bounds in gpiochip_irq_map+0x228/0x248
Read of size 4 at addr ffffffc0dde472e0 by task swapper/0/1
CPU: 7 PID: 1 Comm: swapper/0 Not tainted 4.14.72 #34
Call trace:
[<ffffff9008093638>] dump_backtrace+0x0/0x718
[<ffffff9008093da4>] show_stack+0x20/0x2c
[<ffffff90096b9224>] __dump_stack+0x20/0x28
[<ffffff90096b91c8>] dump_stack+0x80/0xbc
[<ffffff900845a350>] print_address_description+0x70/0x238
[<ffffff900845a8e4>] kasan_report+0x1cc/0x260
[<ffffff900845aa14>] __asan_report_load4_noabort+0x2c/0x38
[<ffffff900897e098>] gpiochip_irq_map+0x228/0x248
[<ffffff900820cc08>] irq_domain_associate+0x114/0x2ec
[<ffffff900820d13c>] irq_create_mapping+0x120/0x234
[<ffffff900820da78>] irq_create_fwspec_mapping+0x4c8/0x88c
[<ffffff900820e2d8>] irq_create_of_mapping+0x180/0x210
[<ffffff900917114c>] of_irq_get+0x138/0x198
[<ffffff9008dc70ac>] spi_drv_probe+0x94/0x178
[<ffffff9008ca5168>] driver_probe_device+0x51c/0x824
[<ffffff9008ca6538>] __device_attach_driver+0x148/0x20c
[<ffffff9008ca14cc>] bus_for_each_drv+0x120/0x188
[<ffffff9008ca570c>] __device_attach+0x19c/0x2dc
[<ffffff9008ca586c>] device_initial_probe+0x20/0x2c
[<ffffff9008ca18bc>] bus_probe_device+0x80/0x154
[<ffffff9008c9b9b4>] device_add+0x9b8/0xbdc
[<ffffff9008dc7640>] spi_add_device+0x1b8/0x380
[<ffffff9008dcbaf0>] spi_register_controller+0x111c/0x1378
[<ffffff9008dd6b10>] spi_geni_probe+0x4dc/0x6f8
[<ffffff9008cab058>] platform_drv_probe+0xdc/0x130
[<ffffff9008ca5168>] driver_probe_device+0x51c/0x824
[<ffffff9008ca59cc>] __driver_attach+0x100/0x194
[<ffffff9008ca0ea8>] bus_for_each_dev+0x104/0x16c
[<ffffff9008ca58c0>] driver_attach+0x48/0x54
[<ffffff9008ca1edc>] bus_add_driver+0x274/0x498
[<ffffff9008ca8448>] driver_register+0x1ac/0x230
[<ffffff9008caaf6c>] __platform_driver_register+0xcc/0xdc
[<ffffff9009c4b33c>] spi_geni_driver_init+0x1c/0x24
[<ffffff9008084cb8>] do_one_initcall+0x240/0x3dc
[<ffffff9009c017d0>] kernel_init_freeable+0x378/0x468
[<ffffff90096e8240>] kernel_init+0x14/0x110
[<ffffff9008086fcc>] ret_from_fork+0x10/0x18
The buggy address belongs to the page:
page:ffffffbf037791c0 count:0 mapcount:0 mapping: (null) index:0x0
flags: 0x4000000000000000()
raw: 4000000000000000 0000000000000000 0000000000000000 00000000ffffffff
raw: ffffffbf037791e0 ffffffbf037791e0 0000000000000000 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffffffc0dde47180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffffc0dde47200: f1 f1 f1 f1 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f2 f2
>ffffffc0dde47280: f2 f2 00 00 00 00 00 00 00 00 00 00 f3 f3 f3 f3
^
ffffffc0dde47300: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffffc0dde47380: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Let's leave around one unsigned int in the gpio_irq_chip struct for the
single parent irq case and repoint the 'parents' array at it. This way
code is left mostly intact to setup parents and we waste an extra few
bytes per structure of which there should be only a handful in a system.
Cc: Evan Green <evgreen@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Fixes: e0d8972898 ("gpio: Implement tighter IRQ chip integration")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2018-10-08
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) sk_lookup_[tcp|udp] and sk_release helpers from Joe Stringer which allow
BPF programs to perform lookups for sockets in a network namespace. This would
allow programs to determine early on in processing whether the stack is
expecting to receive the packet, and perform some action (eg drop,
forward somewhere) based on this information.
2) per-cpu cgroup local storage from Roman Gushchin.
Per-cpu cgroup local storage is very similar to simple cgroup storage
except all the data is per-cpu. The main goal of per-cpu variant is to
implement super fast counters (e.g. packet counters), which don't require
neither lookups, neither atomic operations in a fast path.
The example of these hybrid counters is in selftests/bpf/netcnt_prog.c
3) allow HW offload of programs with BPF-to-BPF function calls from Quentin Monnet
4) support more than 64-byte key/value in HW offloaded BPF maps from Jakub Kicinski
5) rename of libbpf interfaces from Andrey Ignatov.
libbpf is maturing as a library and should follow good practices in
library design and implementation to play well with other libraries.
This patch set brings consistent naming convention to global symbols.
6) relicense libbpf as LGPL-2.1 OR BSD-2-Clause from Alexei Starovoitov
to let Apache2 projects use libbpf
7) various AF_XDP fixes from Björn and Magnus
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
