Add functions to access the maximum size we can read/write using
regmap_raw_read/write().
This helps drivers that need to know how much they can write with the
raw functions without problems. There are some devices (e.g. bmc150)
that have fifos as registers which need to be read in specific chunks
otherwise samples are dropped.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are some buses which have a limit on the maximum number of bytes
that can be send/received. An example for this is
I2C_FUNC_SMBUS_I2C_BLOCK which does not support any reads/writes of more
than 32 bytes. The regmap_bulk operations should still be able to
utilize the full 32 bytes in this case.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
By default (subject to the sysctl settings), IPv6 sockets listen also for
IPv4 traffic. Vxlan is not prepared for that and expects IPv6 header in
packets received through an IPv6 socket.
In addition, it's currently not possible to have both IPv4 and IPv6 vxlan
tunnel on the same port (unless bindv6only sysctl is enabled), as it's not
possible to create and bind both IPv4 and IPv6 vxlan interfaces and there's
no way to specify both IPv4 and IPv6 remote/group IP addresses.
Set IPV6_V6ONLY on vxlan sockets to fix both of these issues. This is not
done globally in udp_tunnel, as l2tp and tipc seems to work okay when
receiving IPv4 packets on IPv6 socket and people may rely on this behavior.
The other tunnels (geneve and fou) do not support IPv6.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's currently nothing preventing directing packets with IPv6
encapsulation data to IPv4 tunnels (and vice versa). If this happens,
IPv6 addresses are incorrectly interpreted as IPv4 ones.
Track whether the given ip_tunnel_key contains IPv4 or IPv6 data. Store this
in ip_tunnel_info. Reject packets at appropriate places if they are supposed
to be encapsulated into an incompatible protocol.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mode field holds a single bit of information only (whether the
ip_tunnel_info struct is for rx or tx). Change the mode field to bit flags.
This allows more mode flags to be added.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit c05cdb1b86 ("netlink: allow large data transfers from
user-space"), the kernel may fail to allocate the necessary room for the
acknowledgment message back to userspace. This patch introduces a new
socket option that trims off the payload of the original netlink message.
The netlink message header is still included, so the user can guess from
the sequence number what is the message that has triggered the
acknowledgment.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The expectation is that the legacy / non-standard pmem discovery method
(e820 type-12) will only ever be used to describe small quantities of
persistent memory. Larger capacities will be described via the ACPI
NFIT. When "allocate struct page from pmem" support is added this default
policy can be overridden by assigning a legacy pmem namespace to a pfn
device, however this would be only be necessary if a platform used the
legacy mechanism to define a very large range.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds the value of the CNP opcode to the existing list of enumerated
opcodes in ib_pack.h
Add common OPA header definitions for driver
build:
- opa_port_info.h
- opa_smi.h
- hfi1_user.h
Additionally, ib_mad.h, has additional definitions
that are common to ib_drivers including:
- trap support
- cca support
The qib driver has the duplication removed in favor
those in ib_mad.h
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: John, Jubin <jubin.john@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The mlx5 driver exposes device capability IB_DEVICE_LOCAL_DMA_LKEY
but does not set the the device local_dma_lkey. This breaks
rpcrdma drivers.
Query and set this lkey when creating the device resources.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The governor dummies for the !CONFIG_PM_GENERIC_DOMAINS case are
unusable, as a governors is always referred to by taking its address,
which you can't do with a literal NULL pointer.
I.e.
pm_genpd_init(genpd, &simple_qos_governor, false);
fails to compile with:
error: lvalue required as unary '&' operand
Hence just remove the governor dummies.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next tree.
In sum, patches to address fallout from the previous round plus updates from
the IPVS folks via Simon Horman, they are:
1) Add a new scheduler to IPVS: The weighted overflow scheduling algorithm
directs network connections to the server with the highest weight that is
currently available and overflows to the next when active connections exceed
the node's weight. From Raducu Deaconu.
2) Fix locking ordering in IPVS, always take rtnl_lock in first place. Patch
from Julian Anastasov.
3) Allow to indicate the MTU to the IPVS in-kernel state sync daemon. From
Julian Anastasov.
4) Enhance multicast configuration for the IPVS state sync daemon. Also from
Julian.
5) Resolve sparse warnings in the nf_dup modules.
6) Fix a linking problem when CONFIG_NF_DUP_IPV6 is not set.
7) Add ICMP codes 5 and 6 to IPv6 REJECT target, they are more informative
subsets of code 1. From Andreas Herz.
8) Revert the jumpstack size calculation from mark_source_chains due to chain
depth miscalculations, from Florian Westphal.
9) Calm down more sparse warning around the Netfilter tree, again from Florian
Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
generalize FETCH_FUNC_NAME(memory, string) into
strncpy_from_unsafe() and fix sparse warnings that were
present in original implementation.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inetpeer caches based on address only, so duplicate IP addresses within
a namespace return the same cached entry. Enhance the ipv4 address key
to contain both the IPv4 address and VRF device index.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the inetpeer_addr_base union to inetpeer_addr and drop
inetpeer_addr_base.
Both the a6 and in6_addr overlays are not needed; drop the __be32 version
and rename in6 to a6 for consistency with ipv4. Add a new u32 array to
the union which removes the need for the typecast in the compare function
and the use of a consistent arg for both ipv4 and ipv6 addresses which
makes the compare function more readable.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_metrics and inetpeer both have functions to compare inetpeer
addresses. Consolidate into 1 version.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use inetpeer set,get helpers in tcp_metrics rather than peeking into
the inetpeer_addr struct.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The range of addresses between 224.0.0.0 and 224.0.0.255 inclusive, is
reserved for the use of routing protocols and other low-level topology
discovery or maintenance protocols, such as gateway discovery and
group membership reporting. Multicast routers should not forward any
multicast datagram with destination addresses in this range,
regardless of its TTL.
Currently, IGMP reports are generated for this reserved range of
addresses even though a router will ignore this information since it
has no purpose. However, the presence of reserved group addresses in
an IGMP membership report uses up network bandwidth and can also
obscure addresses of interest when inspecting membership reports using
packet inspection or debug messages.
Although the RFCs for the various version of IGMP (e.g.RFC 3376 for
v3) do not specify that the reserved addresses be excluded from
membership reports, it should do no harm in doing so. In particular
there should be no adverse effect in any IGMP snooping functionality
since 224.0.0.x is specifically excluded as per RFC 4541 (IGMP and MLD
Snooping Switches Considerations) section 2.1.2. Data Forwarding
Rules:
2) Packets with a destination IP (DIP) address in the 224.0.0.X
range which are not IGMP must be forwarded on all ports.
IGMP reports for local multicast groups can now be optionally
inhibited by means of a system control variable (by setting the value
to zero) e.g.:
echo 0 > /proc/sys/net/ipv4/igmp_link_local_mcast_reports
To retain backwards compatibility the previous behaviour is retained
by default on system boot or reverted by setting the value back to
non-zero e.g.:
echo 1 > /proc/sys/net/ipv4/igmp_link_local_mcast_reports
Signed-off-by: Philip Downey <pdowney@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a ->handler and a ->handler_data field to struct scsi_device and kill
this indirection. Also move struct scsi_device_handler to scsi_dh.h so that
changes to it don't require rebuilding every SCSI LLDD.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Add a single list of devices that need non-ALUA device handlers to the core
scsi_dh code so that we can autoload the modules for them at probe time.
While this is a little ugly in terms of architecture it actually
significantly simplifies the code in addition to the new autoloading
functionality.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Stop building scsi_dh as a separate module and integrate it fully into the
core SCSI code with explicit callouts at bus scan time. For now the
callouts are placed at the same point as the old bus notifiers were called,
but in the future we will be able to look at ALUA INQUIRY data earlier on.
Note that this also means that the device handler modules need to be loaded
by the time we scan the bus. The next patches will add support for
autoloading device handlers at bus scan time to make sure they are always
loaded if they are enabled in the kernel config.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This way we can reused the same code any attachment method, not just those
requested from dm-mpath.
[jejb: fixup checkpatch error]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
While allowing dm-mpath to attach device handlers is a functionality we need
for backwards compatibility reason there is no reason to reference count
them and detach them if dm-mpath stops using the device for some reason.
If the device handler works for the given device it can just stay attached,
and we can take the retain_hw_handler codepath.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
A number of functions and structures in the sound subsystem had incomplete
and/or obsolete DocBook comments, leading to warnings when the docs were
built. Correct those comments so that we can enjoy our audio in the
absence of warning noise.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
cpuidle_device::safe_state_index need to be initialized before
use, it should be the same as cpuidle_driver::safe_state_index.
We tackled this issue by removing the safe_state_index from the
cpuidle_device structure and use the one in the cpuidle_driver
structure instead.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On the board n090401 (Seagate NAS 4-Bay), the LED mode mapping (GPIO
values to LED mode) is different from the one used on other boards
supported by the leds-ns2 driver.
With this patch the hardcoded mapping is removed from leds-ns2. Now,
it must be defined either in the platform data (if an old-fashion board
setup file is used) or in the DT node. In order to allow the later, this
patch also introduces a modes-map property for the leds-ns2 DT binding.
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This way users can attach noqueue just like any other qdisc using tc
without having to mess with tx_queue_len first.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Client sends a SETATTR request after OPEN for updating attributes.
For create file with S_ISGID is set, the S_ISGID in SETATTR will be
ignored at nfs server as chmod of no PERMISSION.
v3, same as v2.
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Create file with attributs as NFS4_CREATE_EXCLUSIVE4_1 mode
depends on suppattr_exclcreat attribut.
v3, same as v2.
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
v4.1/v4.2 have define attributes at word2, nfs client also support
security label now.
v3, same as v2.
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Given that a write-back (WB) mapping plus non-temporal stores is
expected to be the most efficient way to access PMEM, update the
definition of ARCH_HAS_PMEM_API to imply arch support for
WB-mapped-PMEM. This is needed as a pre-requisite for adding PMEM to
the direct map and mapping it with struct page.
The above clarification for X86_64 means that memcpy_to_pmem() is
permitted to use the non-temporal arch_memcpy_to_pmem() rather than
needlessly fall back to default_memcpy_to_pmem() when the pcommit
instruction is not available. When arch_memcpy_to_pmem() is not
guaranteed to flush writes out of cache, i.e. on older X86_32
implementations where non-temporal stores may just dirty cache,
ARCH_HAS_PMEM_API is simply disabled.
The default fall back for persistent memory handling remains. Namely,
map it with the WT (write-through) cache-type and hope for the best.
arch_has_pmem_api() is updated to only indicate whether the arch
provides the proper helpers to meet the minimum "writes are visible
outside the cache hierarchy after memcpy_to_pmem() + wmb_pmem()". Code
that cares whether wmb_pmem() actually flushes writes to pmem must now
call arch_has_wmb_pmem() directly.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
[hch: set ARCH_HAS_PMEM_API=n on x86_32]
Reviewed-by: Christoph Hellwig <hch@lst.de>
[toshi: x86_32 compile fixes]
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This behaves like devm_memremap except that it ensures we have page
structures available that can back the region.
Signed-off-by: Christoph Hellwig <hch@lst.de>
[djbw: catch attempts to remap RAM, drop flags]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
While pmem is usable as a block device or via DAX mappings to userspace
there are several usage scenarios that can not target pmem due to its
lack of struct page coverage. In preparation for "hot plugging" pmem
into the vmemmap add ZONE_DEVICE as a new zone to tag these pages
separately from the ones that are subject to standard page allocations.
Importantly "device memory" can be removed at will by userspace
unbinding the driver of the device.
Having a separate zone prevents allocation and otherwise marks these
pages that are distinct from typical uniform memory. Device memory has
different lifetime and performance characteristics than RAM. However,
since we have run out of ZONES_SHIFT bits this functionality currently
depends on sacrificing ZONE_DMA.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Jerome Glisse <j.glisse@gmail.com>
[hch: various simplifications in the arch interface]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Three architectures already define these, and we'll need them genericly
soon.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
None of the implementations currently use it. The common
bdev_direct_access() entry point handles all the size checks before
calling ->direct_access().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When CONFIG_OPENVSWITCH is set, and CONFIG_NETFILTER is not set, the
openvswitch IPv6 fragmentation handling cannot refer to ipv6_ops because
it isn't defined. Add a dummy version to avoid #ifdefs in source files.
Fixes: 7f8a436 "openvswitch: Add conntrack action"
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add this helper so code can easily figure out if netdev is openswitch.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add this helper so code can easily figure out if netdev is a bridge.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add info that is passed along with NETDEV_CHANGEUPPER event.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
geneve_core module handles send and receive functionality.
This way OVS could use the Geneve API. Now with use of
tunnel meatadata mode OVS can directly use Geneve netdevice.
So there is no need for separate module for Geneve. Following
patch consolidates Geneve protocol processing in single module.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch create new tunnel flag which enable
tunnel metadata collection on given device. These devices
can be used by tunnel metadata based routing or by OVS.
Geneve Consolidation patch get rid of collect_md_tun to
simplify tunnel lookup further.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce function udp_tun_rx_dst() to initialize tunnel dst on
receive path.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
