The length information for available buffer space for CCA
replies is covered with two fields in the T6 header prepended
on each CCA reply: fromcardlen1 and fromcardlen2. The sum of
these both values must not exceed the AP bus limit for this
card (24KB for CEX8, 12KB CEX7 and older) minus the always
present headers.
The current code adjusted the fromcardlen2 value in case
of exceeding the AP bus limit when there was a non-zero
value given from userspace. Some tests now showed that this
was the wrong assumption. Instead the userspace value given for
this field should always be trusted and if the sum of the
two fields exceeds the AP bus limit for this card the first
field fromcardlen1 should be adjusted instead.
So now the calculation is done with this new insight in mind.
Also some additional checks for overflow have been introduced
and some comments to provide some documentation for future
maintainers of this complicated calculation code.
Furthermore the 128 bytes of fix overhead which is used
in the current code is not correct. Investigations showed
that for a reply always the same two header structs are
prepended before a possible payload. So this is also fixed
with this patch.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Remove ZCRYPT_MULTIDEVNODES kernel config option and make
the dependent code always build.
The last years showed, that this option is enabled on all distros
and exploited by some features (for example CEX plugin for kubernetes).
So remove this choice as it was never used to switch off the multiple
devices support for the zcrypt device driver.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
All kind of administrative requests should not been retried. Some card
firmware detects this and assumes a replay attack. This patch checks
on failure if the low level functions indicate a retry (EAGAIN) and
checks for the ADMIN flag set on the request message. If this both
are true, the response code for this message is changed to EIO to make
sure the zcrypt API layer does not attempt to retry the request. As of
now the ADMIN flag is set for a request message when
- for EP11 the field 'flags' of the EP11 CPRB struct has the leftmost
bit set.
- for CCA when the CPRB minor version is 'T3', 'T5', 'T6' or 'T7'.
Please note that the do-not-retry only applies to a request
which has been sent to the card (= has been successfully enqueued) but
the reply indicates some kind of failure and by default it would be
replied. It is totally fine to retry a request if a previous attempt
to enqueue the msg into the firmware queue had some kind of failure
and thus the card has never seen this request.
Reported-by: Frank Uhlig <Frank.Uhlig1@ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
This patch removes most of the debug code which
is build in when CONFIG_ZCRYPT_DEBUG is enabled.
There is no real exploiter for this code any more and
at least one ioctl fails with this code enabled.
The CONFIG_ZCRYPT_DEBUG kernel config option still
makes sense as some debug sysfs entries can get
enabled with this and maybe long term a new better
designed debug and error injection way will get
introduced.
This patch only removes code surrounded by the named
kernel config option. This option should by default
always be off anyway. The structs and defines removed
by the patch have been used only by code surrounded
by a CONFIG_ZCRYPT_DEBUG ifdef and thus can be removed
also.
In the end this patch removes all the failure-injection
possibilities which had been available when the kernel
had been build with CONFIG_ZCRYPT_DEBUG. It has never
been used that much and was too unflexible anyway.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
zcrypt_unlocked_ioctl() allocates 256k with kzalloc() which is likely to
fail if memory is fragmented. To avoid that use kvmalloc_array() instead,
like it is done at several other places for the same reason.
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Add support for a new 'non CCA clear key token' with these
ECC clear keys supported:
- ECC P256
- ECC P384
- ECC P521
- ECC ED25519
- ECC ED448
This makes it possible to derive a protected key from this
ECC clear key input via PKEY_KBLOB2PROTK3 ioctl. As of now
the only way to derive protected keys from these clear key
tokens is via PCKMO instruction. For AES keys an alternate
path via creating a secure key from the clear key and then
derive a protected key from the secure key exists. This
alternate path is not implemented for ECC keys as it would
require to rearrange and maybe recalculate the clear key
material for input to derive an CCA or EP11 ECC secure key.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
This is an internal rework of the pkey code to not use the
struct pkey_protkey internal any more. This struct has a hard
coded protected key buffer with MAXPROTKEYSIZE = 64 bytes.
However, with support for ECC protected key, this limit is
too short and thus this patch reworks all the internal code
to use the triple u8 *protkey, u32 protkeylen, u32 protkeytype
instead. So the ioctl which still has to deal with this struct
coming from userspace and/or provided to userspace invoke all
the internal functions now with the triple instead of passing
a pointer to struct pkey_protkey.
Also the struct pkey_clrkey has been internally replaced in
a similar way. This struct also has a hard coded clear key
buffer of MAXCLRKEYSIZE = 32 bytes and thus is not usable with
e.g. ECC clear key material.
This is a transparent rework for userspace applications using
the pkey API. The internal kernel API used by the PAES crypto
ciphers has been adapted to this change to make it possible
to provide ECC protected keys via this interface in the future.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
This patch introduces reverse x-mas trees for all
local variables on all the functions in pkey.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Key blobs for the IOCTLs PKEY_KBLOB2PROTK[23] may contain clear key
material. Zeroize the copies of these keys in kernel memory after
creating the protected key.
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Pull s390 updates from Vasily Gorbik:
- Add support for stackleak feature. Also allow specifying
architecture-specific stackleak poison function to enable faster
implementation. On s390, the mvc-based implementation helps decrease
typical overhead from a factor of 3 to just 25%
- Convert all assembler files to use SYM* style macros, deprecating the
ENTRY() macro and other annotations. Select ARCH_USE_SYM_ANNOTATIONS
- Improve KASLR to also randomize module and special amode31 code base
load addresses
- Rework decompressor memory tracking to support memory holes and
improve error handling
- Add support for protected virtualization AP binding
- Add support for set_direct_map() calls
- Implement set_memory_rox() and noexec module_alloc()
- Remove obsolete overriding of mem*() functions for KASAN
- Rework kexec/kdump to avoid using nodat_stack to call purgatory
- Convert the rest of the s390 code to use flexible-array member
instead of a zero-length array
- Clean up uaccess inline asm
- Enable ARCH_HAS_MEMBARRIER_SYNC_CORE
- Convert to using CONFIG_FUNCTION_ALIGNMENT and enable
DEBUG_FORCE_FUNCTION_ALIGN_64B
- Resolve last_break in userspace fault reports
- Simplify one-level sysctl registration
- Clean up branch prediction handling
- Rework CPU counter facility to retrieve available counter sets just
once
- Other various small fixes and improvements all over the code
* tag 's390-6.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (118 commits)
s390/stackleak: provide fast __stackleak_poison() implementation
stackleak: allow to specify arch specific stackleak poison function
s390: select ARCH_USE_SYM_ANNOTATIONS
s390/mm: use VM_FLUSH_RESET_PERMS in module_alloc()
s390: wire up memfd_secret system call
s390/mm: enable ARCH_HAS_SET_DIRECT_MAP
s390/mm: use BIT macro to generate SET_MEMORY bit masks
s390/relocate_kernel: adjust indentation
s390/relocate_kernel: use SYM* macros instead of ENTRY(), etc.
s390/entry: use SYM* macros instead of ENTRY(), etc.
s390/purgatory: use SYM* macros instead of ENTRY(), etc.
s390/kprobes: use SYM* macros instead of ENTRY(), etc.
s390/reipl: use SYM* macros instead of ENTRY(), etc.
s390/head64: use SYM* macros instead of ENTRY(), etc.
s390/earlypgm: use SYM* macros instead of ENTRY(), etc.
s390/mcount: use SYM* macros instead of ENTRY(), etc.
s390/crc32le: use SYM* macros instead of ENTRY(), etc.
s390/crc32be: use SYM* macros instead of ENTRY(), etc.
s390/crypto,chacha: use SYM* macros instead of ENTRY(), etc.
s390/amode31: use SYM* macros instead of ENTRY(), etc.
...
Review and rework all the zero length array occurrences
within structs to flexible array fields or comment if
not used at all. However, some struct fields are there
for documentation purpose or to have correct sizeof()
evaluation of a struct and thus should not get deleted.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The preparation of the key data struct for a CCA RSA ME
operation had some improvement to skip leading zeros
in the key's exponent. However, all supported CCA cards
nowadays support leading zeros in key tokens.
So for simplifying the CCA key preparing code, this
patch simply removes this optimization code.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
There was some ancient code which padded the results of
a clear key ME or CRT operation with some PKCS 1.2 header.
According to the comment this was only needed by crypto
cards older than the CEX2. These cards are not supported
any more and so this patch removes this obscure result
padding code.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
We need the fixes in here for testing, as well as the driver core
changes for documentation updates to build on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device release callback function invoked to release the matrix device
uses the dev_get_drvdata(device *dev) function to retrieve the
pointer to the vfio_matrix_dev object in order to free its storage. The
problem is, this object is not stored as drvdata with the device; since the
kfree function will accept a NULL pointer, the memory for the
vfio_matrix_dev object is never freed.
Since the device being released is contained within the vfio_matrix_dev
object, the container_of macro will be used to retrieve its pointer.
Fixes: 1fde573413 ("s390: vfio-ap: base implementation of VFIO AP device driver")
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Link: https://lore.kernel.org/r/20230320150447.34557-1-akrowiak@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Review and extend the low level AP code to be able to
deal with asynchronous reported errors on APQNs.
The hypervisor and the SE guest may be confronted with
an asynchronously reported error at return of an AP
instruction. So all places where AP instructions are
called need review and may eventually need extensions.
However, not all places need rework. As together with
the AP status and the enabled asynch bit there is always
a response code set. The asynch error reporting comes
with new response codes which may be simple handled in
the default case of a switch statement.
The idea behind this patch is to report asynch errors
as -EPERM (read this as "Operation not permitted") which
reflects the fact that only a rapq (with F bit enabled)
is a valid AP instruction when an asynch error is flagged.
The AP queue state machine functions return
AP_SM_WAIT_NONE when a asynch error is detected to reflect
the fact, that the state machine can't do anything with
such an error as long as the queue is reset.
Unfortunately the ap bus scan function needed some
update as the ap_queue_info() now needs to return
3 states: 1 if an APQN exists and info is available,
-1 if it is assumed an APQN does not exist and the new
return value 0 without any info values filled. This 0
returncode is handled as "there is an APQN but we currently
don't know any more hw info about this, so please use
your previous info and try again later".
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Implementation of the new functions for SE AP support:
bind, unbind and associate. There are two new sysfs
attributes for this:
/sys/devices/ap/cardxx/xx.yyyy/se_bind
/sys/devices/ap/cardxx/xx.yyyy/se_associate
Writing a 1 into the se_bind attribute triggers the
SE AP bind for this AP queue, writing a 0 into does
an unbind - that's a reset (RAPQ) with the F bit enabled.
The se_associate attribute needs an integer value in
range 0...2^16-1 written in. This is the index into a
secrets table feed into the ultravisor. For more details
please see the Architecture documents.
These both new ap queue attributes are only visible
inside a SE guest with SB (Secure Binding) available.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
For some events the ap bus needs to poll. For example
when an AP queue is reset until the reset is through.
Also when no interrupt support is available (e.g. zVM)
there is a need to poll until all requests have been
processed and all replies have been delivered.
Polling is done with a high resolution timer by default
run with a rate of 4kHz (LPAR) or 666Hz (zVM guest).
For some events (wait for reset complete, wait for irq
enabled complete) this is a much too high poll rate
which triggers a lot of TAPQ invocations.
This patch introduces the possibility for the state
machine functions to return a new wait enum
AP_SM_WAIT_LOW_TIMEOUT which gives a hint to the
ap_wait() function to eventually set up the timer
with a more relaxed timeout value of 25Hz.
This patch also includes a slight rework of the sysfs
functions parsing the timer related stuff: Use of
kstrtobool and kstrtoul instead of sscanf.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Extent the ap inline functions ap_rapq() (calls PQAP(RAPQ))
and ap_zapq() (calls PQAP(ZAPQ)) with a new parameter to
enable the new architectured F bit which forces an
unassociate and/or unbind on a secure execution associated
and/or bound queue.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
With SE SB (Secure Binding) some currently unused and thus always
zero bits in the TAPQ GR2 result are now used to show the binding
state of a queue. So to check if a card has changed the comparing
base is exactly this GR2 value shown as 'ap_function' in sysfs
(/sys/devices/ap/cardxx/ap_functions). Now there is some queue
specific info in this info and so a new mask TAPQ_CARD_FUNC_CMP_MASK
is used to filter out only the relevant bits for card compare.
For the same reason now the function bits (including exactly this
bind/associate information) need to be exposed to user space now.
So tools like lszcrypt can evaluate binding/association state on a
queue base. So here comes a new sysfs attribute
/sys/devices/ap/cardxx/xx.yyyy/ap_functions
This sysfs attribute is similar to the already existing
ap_functions attribute at ap card level. It shows the
upper 32 bits of GR2 from an invocation of TAPQ for this
AP queue.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
This patch introduces a new struct ap_tapq_gr2 which covers
the response in GR2 on TAPQ invocation. This makes it much
easier and less error-prone for the calling functions to
access the right field without shifting and masking.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Introduce a new AP bus sysfs attribute /sys/bus/ap/features
which shows the features from the QCI information.
Currently these feature bits are evaluated:
- QCI S bit is shown as 'APSC'
- QCI N bit is shown as 'APXA'
- QCI C bit is shown as 'QACT'
- QCI R bit is shown as 'RC8A'
- QCI B bit is shown as 'APSB'
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
This patch introduces an update to the ap_config_info
struct which is filled with the QCI subfunction. There
is a new bit apsb (short 'B') showing if the AP secure
bind facility is available. The patch also includes a
simple function ap_sb_available() wrapping this bit test.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The inline ap_dqap function does not return the number of
bytes actually written into the message buffer. The calling
code inspects the AP message header to figure out what kind
of AP message has been received and pulls the length
information from this header. This processing may not work
correctly in cases where only a fragment of the reply is
received.
With this patch the ap_dqap inline function now returns
the number of actually written bytes in the *length parameter.
So the calling function has a chance to compare the number of
received bytes against what the AP message header length
field states. This is especially useful in cases where a
message could only get partially received.
The low level reply processing functions needed some rework
to be able to catch this new length information and compare
it the right way. The rework also deals with some situations
where until now the reply length was not correctly calculated
and/or set.
All this has been heavily tested as the modifications on
the reply length information may affect crypto load.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Since s390 kernel build does not support 32 bit build any
more there is no difference between long and long long.
So this patch reworks all occurrences of psmid (a 64 bit
value) to use unsigned long now.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Pull more s390 updates from Heiko Carstens:
- Add empty command line parameter handling stubs to kernel for all
command line parameters which are handled in the decompressor. This
avoids invalid "Unknown kernel command line parameters" messages from
the kernel, and also avoids that these will be incorrectly passed to
user space. This caused already confusion, therefore add the empty
stubs
- Add missing phys_to_virt() handling to machine check handler
- Introduce and use a union to be used for zcrypt inline assemblies.
This makes sure that only a register wide member of the union is
passed as input and output parameter to inline assemblies, while
usual C code uses other members of the union to access bit fields of
it
- Add and use a READ_ONCE_ALIGNED_128() macro, which can be used to
atomically read a 128-bit value from memory. This replaces the
(mis-)use of the 128-bit cmpxchg operation to do the same in cpum_sf
code. Currently gcc does not generate the used lpq instruction if
__READ_ONCE() is used for aligned 128-bit accesses, therefore use
this s390 specific helper
- Simplify machine check handler code if a task needs to be killed
because of e.g. register corruption due to a machine malfunction
- Perform CPU reset to clear pending interrupts and TLB entries on an
already stopped target CPU before delegating work to it
- Generate arch/s390/boot/vmlinux.map link map for the decompressor,
when CONFIG_VMLINUX_MAP is enabled for debugging purposes
- Fix segment type handling for dcssblk devices. It incorrectly always
returned type "READ/WRITE" even for read-only segements, which can
result in a kernel panic if somebody tries to write to a read-only
device
- Sort config S390 select list again
- Fix two kprobe reenter bugs revealed by a recently added kprobe kunit
test
* tag 's390-6.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/kprobes: fix current_kprobe never cleared after kprobes reenter
s390/kprobes: fix irq mask clobbering on kprobe reenter from post_handler
s390/Kconfig: sort config S390 select list again
s390/extmem: return correct segment type in __segment_load()
s390/decompressor: add link map saving
s390/smp: perform cpu reset before delegating work to target cpu
s390/mcck: cleanup user process termination path
s390/cpum_sf: use READ_ONCE_ALIGNED_128() instead of 128-bit cmpxchg
s390/rwonce: add READ_ONCE_ALIGNED_128() macro
s390/ap,zcrypt,vfio: introduce and use ap_queue_status_reg union
s390/nmi: fix virtual-physical address confusion
s390/setup: do not complain about parameters handled in decompressor
Introduce a new ap queue status register wrapper union to access register
wide values. So the inline assembler only sees register wide values but the
surrounding code may use a more structured view of the same value and a
reader of the code (and the compiler) gets a clear understanding about the
mapping between fields and register values.
All the changes to access the ap queue status are local to the inline
functions within ap.h. However, the struct ap_qirq_ctrl has been replaces
by a union for same reason and this needed slight adaptions in the calling
code.
Suggested-by: Halil Pasic <pasic@linux.ibm.com>
Suggested-by: Andreas Arnez <arnez@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
The NIB is architecturally invalid if the address designates a
storage location that is not installed or if it is zero.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Reported-by: Janosch Frank <frankja@linux.ibm.com>
Fixes: ec89b55e3b ("s390: ap: implement PAPQ AQIC interception in kernel")
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Some response codes returned from the queue reset function are not being
handled correctly; this patch fixes them:
1. Response code 3, AP queue deconfigured: Deconfiguring an AP adapter
resets all of its queues, so this is handled by indicating the reset
verification completed successfully.
2. For all response codes other than 0 (normal reset completion), 2
(queue reset in progress) and 3 (AP deconfigured), the -EIO error will
be returned from the vfio_ap_mdev_reset_queue() function. In all cases,
all fields of the status word other than the response code will be
set to zero, so it makes no sense to check status bits.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Link: https://lore.kernel.org/r/20230118203111.529766-6-akrowiak@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The vfio_ap_mdev_reset_queue() function does not check the status
response code returned form the PQAP(TAPQ) function when verifying the
queue's status; consequently, there is no way of knowing whether
verification failed because the wait time was exceeded, or because the
PQAP(TAPQ) failed.
This patch adds a function to check the status response code from the
PQAP(TAPQ) instruction and logs an appropriate message if it fails.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Link: https://lore.kernel.org/r/20230118203111.529766-3-akrowiak@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Pull VFIO updates from Alex Williamson:
- Replace deprecated git://github.com link in MAINTAINERS (Palmer
Dabbelt)
- Simplify vfio/mlx5 with module_pci_driver() helper (Shang XiaoJing)
- Drop unnecessary buffer from ACPI call (Rafael Mendonca)
- Correct latent missing include issue in iova-bitmap and fix support
for unaligned bitmaps. Follow-up with better fix through refactor
(Joao Martins)
- Rework ccw mdev driver to split private data from parent structure,
better aligning with the mdev lifecycle and allowing us to remove a
temporary workaround (Eric Farman)
- Add an interface to get an estimated migration data size for a
device, allowing userspace to make informed decisions, ex. more
accurately predicting VM downtime (Yishai Hadas)
- Fix minor typo in vfio/mlx5 array declaration (Yishai Hadas)
- Simplify module and Kconfig through consolidating SPAPR/EEH code and
config options and folding virqfd module into main vfio module (Jason
Gunthorpe)
- Fix error path from device_register() across all vfio mdev and sample
drivers (Alex Williamson)
- Define migration pre-copy interface and implement for vfio/mlx5
devices, allowing portions of the device state to be saved while the
device continues operation, towards reducing the stop-copy state size
(Jason Gunthorpe, Yishai Hadas, Shay Drory)
- Implement pre-copy for hisi_acc devices (Shameer Kolothum)
- Fixes to mdpy mdev driver remove path and error path on probe (Shang
XiaoJing)
- vfio/mlx5 fixes for incorrect return after copy_to_user() fault and
incorrect buffer freeing (Dan Carpenter)
* tag 'vfio-v6.2-rc1' of https://github.com/awilliam/linux-vfio: (42 commits)
vfio/mlx5: error pointer dereference in error handling
vfio/mlx5: fix error code in mlx5vf_precopy_ioctl()
samples: vfio-mdev: Fix missing pci_disable_device() in mdpy_fb_probe()
hisi_acc_vfio_pci: Enable PRE_COPY flag
hisi_acc_vfio_pci: Move the dev compatibility tests for early check
hisi_acc_vfio_pci: Introduce support for PRE_COPY state transitions
hisi_acc_vfio_pci: Add support for precopy IOCTL
vfio/mlx5: Enable MIGRATION_PRE_COPY flag
vfio/mlx5: Fallback to STOP_COPY upon specific PRE_COPY error
vfio/mlx5: Introduce multiple loads
vfio/mlx5: Consider temporary end of stream as part of PRE_COPY
vfio/mlx5: Introduce vfio precopy ioctl implementation
vfio/mlx5: Introduce SW headers for migration states
vfio/mlx5: Introduce device transitions of PRE_COPY
vfio/mlx5: Refactor to use queue based data chunks
vfio/mlx5: Refactor migration file state
vfio/mlx5: Refactor MKEY usage
vfio/mlx5: Refactor PD usage
vfio/mlx5: Enforce a single SAVE command at a time
vfio: Extend the device migration protocol with PRE_COPY
...
Pull kvm updates from Paolo Bonzini:
"ARM64:
- Enable the per-vcpu dirty-ring tracking mechanism, together with an
option to keep the good old dirty log around for pages that are
dirtied by something other than a vcpu.
- Switch to the relaxed parallel fault handling, using RCU to delay
page table reclaim and giving better performance under load.
- Relax the MTE ABI, allowing a VMM to use the MAP_SHARED mapping
option, which multi-process VMMs such as crosvm rely on (see merge
commit 382b5b87a9: "Fix a number of issues with MTE, such as
races on the tags being initialised vs the PG_mte_tagged flag as
well as the lack of support for VM_SHARED when KVM is involved.
Patches from Catalin Marinas and Peter Collingbourne").
- Merge the pKVM shadow vcpu state tracking that allows the
hypervisor to have its own view of a vcpu, keeping that state
private.
- Add support for the PMUv3p5 architecture revision, bringing support
for 64bit counters on systems that support it, and fix the
no-quite-compliant CHAIN-ed counter support for the machines that
actually exist out there.
- Fix a handful of minor issues around 52bit VA/PA support (64kB
pages only) as a prefix of the oncoming support for 4kB and 16kB
pages.
- Pick a small set of documentation and spelling fixes, because no
good merge window would be complete without those.
s390:
- Second batch of the lazy destroy patches
- First batch of KVM changes for kernel virtual != physical address
support
- Removal of a unused function
x86:
- Allow compiling out SMM support
- Cleanup and documentation of SMM state save area format
- Preserve interrupt shadow in SMM state save area
- Respond to generic signals during slow page faults
- Fixes and optimizations for the non-executable huge page errata
fix.
- Reprogram all performance counters on PMU filter change
- Cleanups to Hyper-V emulation and tests
- Process Hyper-V TLB flushes from a nested guest (i.e. from a L2
guest running on top of a L1 Hyper-V hypervisor)
- Advertise several new Intel features
- x86 Xen-for-KVM:
- Allow the Xen runstate information to cross a page boundary
- Allow XEN_RUNSTATE_UPDATE flag behaviour to be configured
- Add support for 32-bit guests in SCHEDOP_poll
- Notable x86 fixes and cleanups:
- One-off fixes for various emulation flows (SGX, VMXON, NRIPS=0).
- Reinstate IBPB on emulated VM-Exit that was incorrectly dropped
a few years back when eliminating unnecessary barriers when
switching between vmcs01 and vmcs02.
- Clean up vmread_error_trampoline() to make it more obvious that
params must be passed on the stack, even for x86-64.
- Let userspace set all supported bits in MSR_IA32_FEAT_CTL
irrespective of the current guest CPUID.
- Fudge around a race with TSC refinement that results in KVM
incorrectly thinking a guest needs TSC scaling when running on a
CPU with a constant TSC, but no hardware-enumerated TSC
frequency.
- Advertise (on AMD) that the SMM_CTL MSR is not supported
- Remove unnecessary exports
Generic:
- Support for responding to signals during page faults; introduces
new FOLL_INTERRUPTIBLE flag that was reviewed by mm folks
Selftests:
- Fix an inverted check in the access tracking perf test, and restore
support for asserting that there aren't too many idle pages when
running on bare metal.
- Fix build errors that occur in certain setups (unsure exactly what
is unique about the problematic setup) due to glibc overriding
static_assert() to a variant that requires a custom message.
- Introduce actual atomics for clear/set_bit() in selftests
- Add support for pinning vCPUs in dirty_log_perf_test.
- Rename the so called "perf_util" framework to "memstress".
- Add a lightweight psuedo RNG for guest use, and use it to randomize
the access pattern and write vs. read percentage in the memstress
tests.
- Add a common ucall implementation; code dedup and pre-work for
running SEV (and beyond) guests in selftests.
- Provide a common constructor and arch hook, which will eventually
be used by x86 to automatically select the right hypercall (AMD vs.
Intel).
- A bunch of added/enabled/fixed selftests for ARM64, covering
memslots, breakpoints, stage-2 faults and access tracking.
- x86-specific selftest changes:
- Clean up x86's page table management.
- Clean up and enhance the "smaller maxphyaddr" test, and add a
related test to cover generic emulation failure.
- Clean up the nEPT support checks.
- Add X86_PROPERTY_* framework to retrieve multi-bit CPUID values.
- Fix an ordering issue in the AMX test introduced by recent
conversions to use kvm_cpu_has(), and harden the code to guard
against similar bugs in the future. Anything that tiggers
caching of KVM's supported CPUID, kvm_cpu_has() in this case,
effectively hides opt-in XSAVE features if the caching occurs
before the test opts in via prctl().
Documentation:
- Remove deleted ioctls from documentation
- Clean up the docs for the x86 MSR filter.
- Various fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (361 commits)
KVM: x86: Add proper ReST tables for userspace MSR exits/flags
KVM: selftests: Allocate ucall pool from MEM_REGION_DATA
KVM: arm64: selftests: Align VA space allocator with TTBR0
KVM: arm64: Fix benign bug with incorrect use of VA_BITS
KVM: arm64: PMU: Fix period computation for 64bit counters with 32bit overflow
KVM: x86: Advertise that the SMM_CTL MSR is not supported
KVM: x86: remove unnecessary exports
KVM: selftests: Fix spelling mistake "probabalistic" -> "probabilistic"
tools: KVM: selftests: Convert clear/set_bit() to actual atomics
tools: Drop "atomic_" prefix from atomic test_and_set_bit()
tools: Drop conflicting non-atomic test_and_{clear,set}_bit() helpers
KVM: selftests: Use non-atomic clear/set bit helpers in KVM tests
perf tools: Use dedicated non-atomic clear/set bit helpers
tools: Take @bit as an "unsigned long" in {clear,set}_bit() helpers
KVM: arm64: selftests: Enable single-step without a "full" ucall()
KVM: x86: fix APICv/x2AVIC disabled when vm reboot by itself
KVM: Remove stale comment about KVM_REQ_UNHALT
KVM: Add missing arch for KVM_CREATE_DEVICE and KVM_{SET,GET}_DEVICE_ATTR
KVM: Reference to kvm_userspace_memory_region in doc and comments
KVM: Delete all references to removed KVM_SET_MEMORY_ALIAS ioctl
...
