tcan4552 and tcan4553 do not have wake or state pins, so they are
currently not compatible with the generic driver. The generic driver
uses tcan4x5x_disable_state() and tcan4x5x_disable_wake() if the gpios
are not defined. These functions use register bits that are not
available in tcan4552/4553.
This patch adds support by introducing version information to reflect if
the chip has wake and state pins. Also the version is now checked.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20230728141923.162477-6-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Rename the rx_offload_get_echo_skb() function to
can_rx_offload_get_echo_skb_queue_timestamp(), since it inserts the
echo skb into the rx-offload queue sorted by timestamp.
This is a preparation for adding
can_rx_offload_get_echo_skb_queue_tail(), which adds the echo skb to
the end of the queue. This is intended for devices that do not support
timestamps.
Link: https://lore.kernel.org/all/20230718-gs_usb-rx-offload-v2-1-716e542d14d5@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In gs_usb_disconnect(), all channels are destroyed first, then all
anchored RX URBs (parent->rx_submitted) are disposed with
usb_kill_anchored_urbs().
The call to usb_kill_anchored_urbs() is not needed, as
gs_destroy_candev() of the last active channel already disposes the RX
URBS.
Remove not needed call to usb_kill_anchored_urbs() from
gs_usb_disconnect().
Link: https://lore.kernel.org/all/20230718-gs_usb-cleanups-v1-11-c3b9154ec605@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In gs_destroy_candev(), the netdev is unregistered first, then all
anchored TX URBs (dev->tx_submitted) are disposed with
usb_kill_anchored_urbs().
The call to usb_kill_anchored_urbs() is not needed, as
unregister_candev() calls gs_can_close(), which already disposes the
TX URBS.
Remove not needed call to usb_kill_anchored_urbs() from
gs_destroy_candev().
Link: https://lore.kernel.org/all/20230718-gs_usb-cleanups-v1-10-c3b9154ec605@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the USB device is unplugged, gs_can_close() (which implements the
struct net_device_ops::ndo_stop callback) is called. In this function
an attempt is made to shut down the USB device with a USB control
message. For disconnected devices this will fail and a warning message
is printed.
Silence the driver by removing the printout of the error message if
the reset command fails.
Link: https://lore.kernel.org/all/20230718-gs_usb-cleanups-v1-9-c3b9154ec605@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/all/20230724211841.805053-1-robh@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After an initial link up the CAN device is in ERROR-ACTIVE mode. Due
to a missing CAN_STATE_STOPPED in gs_can_close() it doesn't change to
STOPPED after a link down:
| ip link set dev can0 up
| ip link set dev can0 down
| ip --details link show can0
| 13: can0: <NOARP,ECHO> mtu 16 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 10
| link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
| can state ERROR-ACTIVE restart-ms 1000
Add missing assignment of CAN_STATE_STOPPED in gs_can_close().
Cc: stable@vger.kernel.org
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20230718-gs_usb-fix-can-state-v1-1-f19738ae2c23@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde says:
====================
pull-request: can-next 2023-07-19
The first 2 patches are by Judith Mendez, target the m_can driver and
add hrtimer based polling support for TI AM62x SoCs, where the
interrupt of the MCU domain's m_can cores is not routed to the Cortex
A53 core.
A patch by Rob Herring converts the grcan driver to use the correct DT
include files.
Michal Simek and Srinivas Neeli add support for optional reset control
to the xilinx_can driver.
The next 2 patches are by Jimmy Assarsson and add support for new
Kvaser pciefd to the kvaser_pciefd driver.
Mao Zhu's patch for the ucan driver removes a repeated word from a
comment.
* tag 'linux-can-next-for-6.6-20230719' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: ucan: Remove repeated word
can: kvaser_pciefd: Add support for new Kvaser pciefd devices
can: kvaser_pciefd: Move hardware specific constants and functions into a driver_data struct
can: Explicitly include correct DT includes
can: xilinx_can: Add support for controller reset
dt-bindings: can: xilinx_can: Add reset description
can: m_can: Add hrtimer to generate software interrupt
dt-bindings: net: can: Remove interrupt properties for MCAN
====================
Link: https://lore.kernel.org/r/20230719072348.525039-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/all/20230714174757.4060748-1-robh@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The mcp251xfd controller needs an idle bus to enter 'Normal CAN 2.0
mode' or . The maximum length of a CAN frame is 736 bits (64 data
bytes, CAN-FD, EFF mode, worst case bit stuffing and interframe
spacing). For low bit rates like 10 kbit/s the arbitrarily chosen
MCP251XFD_POLL_TIMEOUT_US of 1 ms is too small.
Otherwise during polling for the CAN controller to enter 'Normal CAN
2.0 mode' the timeout limit is exceeded and the configuration fails
with:
| $ ip link set dev can1 up type can bitrate 10000
| [ 731.911072] mcp251xfd spi2.1 can1: Controller failed to enter mode CAN 2.0 Mode (6) and stays in Configuration Mode (4) (con=0x068b0760, osc=0x00000468).
| [ 731.927192] mcp251xfd spi2.1 can1: CRC read error at address 0x0e0c (length=4, data=00 00 00 00, CRC=0x0000) retrying.
| [ 731.938101] A link change request failed with some changes committed already. Interface can1 may have been left with an inconsistent configuration, please check.
| RTNETLINK answers: Connection timed out
Make MCP251XFD_POLL_TIMEOUT_US timeout calculation dynamic. Use
maximum of 1ms and bit time of 1 full 64 data bytes CAN-FD frame in
EFF mode, worst case bit stuffing and interframe spacing at the
current bit rate.
For easier backporting define the macro MCP251XFD_FRAME_LEN_MAX_BITS
that holds the max frame length in bits, which is 736. This can be
replaced by can_frame_bits(true, true, true, true, CANFD_MAX_DLEN) in
a cleanup patch later.
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20230717-mcp251xfd-fix-increase-poll-timeout-v5-1-06600f34c684@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Introduce timer polling method to MCAN since some SoCs may not
have M_CAN interrupt routed to A53 Linux and do not have
interrupt property in device tree M_CAN node.
On AM62x SoC, MCANs on MCU domain do not have hardware interrupt
routed to A53 Linux, instead they will use timer polling method.
Add an hrtimer to MCAN class device. Each MCAN will have its own
hrtimer instantiated if there is no hardware interrupt found in
device tree M_CAN node. The timer will generate a software
interrupt every 1 ms. In hrtimer callback, we check if there is
a transaction pending by reading a register, then process by
calling the isr if there is.
Tested-by: Hiago De Franco <hiago.franco@toradex.com> # Toradex Verdin AM62
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/all/20230707204714.62964-3-jm@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the gs_usb device driver is unloaded (or unbound) before the
interface is shut down, the USB stack first calls the struct
usb_driver::disconnect and then the struct net_device_ops::ndo_stop
callback.
In gs_usb_disconnect() all pending bulk URBs are killed, i.e. no more
RX'ed CAN frames are send from the USB device to the host. Later in
gs_can_close() a reset control message is send to each CAN channel to
remove the controller from the CAN bus. In this race window the USB
device can still receive CAN frames from the bus and internally queue
them to be send to the host.
At least in the current version of the candlelight firmware, the queue
of received CAN frames is not emptied during the reset command. After
loading (or binding) the gs_usb driver, new URBs are submitted during
the struct net_device_ops::ndo_open callback and the candlelight
firmware starts sending its already queued CAN frames to the host.
However, this scenario was not considered when implementing the
hardware timestamp function. The cycle counter/time counter
infrastructure is set up (gs_usb_timestamp_init()) after the USBs are
submitted, resulting in a NULL pointer dereference if
timecounter_cyc2time() (via the call chain:
gs_usb_receive_bulk_callback() -> gs_usb_set_timestamp() ->
gs_usb_skb_set_timestamp()) is called too early.
Move the gs_usb_timestamp_init() function before the URBs are
submitted to fix this problem.
For a comprehensive solution, we need to consider gs_usb devices with
more than 1 channel. The cycle counter/time counter infrastructure is
setup per channel, but the RX URBs are per device. Once gs_can_open()
of _a_ channel has been called, and URBs have been submitted, the
gs_usb_receive_bulk_callback() can be called for _all_ available
channels, even for channels that are not running, yet. As cycle
counter/time counter has not set up, this will again lead to a NULL
pointer dereference.
Convert the cycle counter/time counter from a "per channel" to a "per
device" functionality. Also set it up, before submitting any URBs to
the device.
Further in gs_usb_receive_bulk_callback(), don't process any URBs for
not started CAN channels, only resubmit the URB.
Fixes: 45dfa45f52 ("can: gs_usb: add RX and TX hardware timestamp support")
Closes: https://github.com/candle-usb/candleLight_fw/issues/137#issuecomment-1623532076
Cc: stable@vger.kernel.org
Cc: John Whittington <git@jbrengineering.co.uk>
Link: https://lore.kernel.org/all/20230716-gs_usb-fix-time-stamp-counter-v1-2-9017cefcd9d5@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The gs_usb driver handles USB devices with more than 1 CAN channel.
The RX path for all channels share the same bulk endpoint (the
transmitted bulk data encodes the channel number). These per-device
resources are allocated and submitted by the first opened channel.
During this allocation, the resources are either released immediately
in case of a failure or the URBs are anchored. All anchored URBs are
finally killed with gs_usb_disconnect().
Currently, gs_can_open() returns with an error if the allocation of a
URB or a buffer fails. However, if usb_submit_urb() fails, the driver
continues with the URBs submitted so far, even if no URBs were
successfully submitted.
Treat every error as fatal and free all allocated resources
immediately.
Switch to goto-style error handling, to prepare the driver for more
per-device resource allocation.
Cc: stable@vger.kernel.org
Cc: John Whittington <git@jbrengineering.co.uk>
Link: https://lore.kernel.org/all/20230716-gs_usb-fix-time-stamp-counter-v1-1-9017cefcd9d5@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
