Pull ARM SoC driver updates from Arnd Bergmann:
"Nothing surprising in the SoC specific drivers, with the usual
updates:
- Added or improved SoC driver support for Tegra234, Exynos4121,
RK3588, as well as multiple Mediatek and Qualcomm chips
- SCMI firmware gains support for multiple SMC/HVC transport and
version 3.2 of the protocol
- Cleanups amd minor changes for the reset controller, memory
controller, firmware and sram drivers
- Minor changes to amd/xilinx, samsung, tegra, nxp, ti, qualcomm,
amlogic and renesas SoC specific drivers"
* tag 'soc-drivers-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (118 commits)
dt-bindings: interrupt-controller: Convert Amlogic Meson GPIO interrupt controller binding
MAINTAINERS: add PHY-related files to Amlogic SoC file list
drivers: meson: secure-pwrc: always enable DMA domain
tee: optee: Use kmemdup() to replace kmalloc + memcpy
soc: qcom: geni-se: Do not bother about enable/disable of interrupts in secondary sequencer
dt-bindings: sram: qcom,imem: document qdu1000
soc: qcom: icc-bwmon: Fix MSM8998 count unit
dt-bindings: soc: qcom,rpmh-rsc: Require power-domains
soc: qcom: socinfo: Add Soc ID for IPQ5300
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5300
soc: qcom: Fix a IS_ERR() vs NULL bug in probe
soc: qcom: socinfo: Add support for new fields in revision 19
soc: qcom: socinfo: Add support for new fields in revision 18
dt-bindings: firmware: scm: Add compatible for SDX75
soc: qcom: mdt_loader: Fix split image detection
dt-bindings: memory-controllers: drop unneeded quotes
soc: rockchip: dtpm: use C99 array init syntax
firmware: tegra: bpmp: Add support for DRAM MRQ GSCs
soc/tegra: pmc: Use devm_clk_notifier_register()
soc/tegra: pmc: Simplify debugfs initialization
...
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for
each SoC vendor, following the same scheme that is used on arm64, mips
and riscv. This has been discussed for many years, but so far we never
did this as there was a plan to move the files out of the kernel
entirely, which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along with
their device drivers.
- The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the
time.
- Amlogic C3 is a Cortex-A35 based smart IP camera chip
- Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
- Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
- Qualcomm SDX75 is the latest generation modem chip that is used as
a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
- Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
Xuantie C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those
included there are 39 new board files, but only five more 32-bit this
time, probably a new low:
- Marantec Maveo board based on dhcor imx6ull module
- Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
- Epson Moverio BT-200 AR glasses based on TI OMAP4
- PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
- ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than we had
in the recent releases:
- Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.
- NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234
- Qualcomm gains support for 6 reference boards on various members of
their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
of the various reference platforms for their new chips.
- Rockchips support for several newer boards: Indiedroid Nova
(rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
Fastrhino R66S/R68S (rk3568)
- TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
Verdin family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
- continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
- support for devicetree overlays on at91, bcm283x
- significant additions to existing SoC support on mediatek,
qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
STM32MP1
As usual, a lot more detail is available in the individual merge
commits"
* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
ARM: mvebu: fix unit address on armada-390-db flash
ARM: dts: Move .dts files to vendor sub-directories
kbuild: Support flat DTBs install
ARM: dts: Add .dts files missing from the build
ARM: dts: allwinner: Use quoted #include
ARM: dts: lan966x: kontron-d10: add PHY interrupts
ARM: dts: lan966x: kontron-d10: fix SPI CS
ARM: dts: lan966x: kontron-d10: fix board reset
ARM: dts: at91: Enable device-tree overlay support for AT91 boards
arm: dts: Enable device-tree overlay support for AT91 boards
arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
ARM: dts: at91: use generic name for shutdown controller
ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
dt-bindings: firmware: brcm,kona-smc: convert to YAML
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
...
Pull devicetree updates from Rob Herring:
"Bindings:
- Add some missing type definitions to properties
- Drop unneeded quotes and use absolute paths in bindings
- Remove redundant "binding" or "schema" in binding titles
- Add bindings for Ralink SoCs interrupt controller, QCA2066
Bluetooth, infineon,irps5401, new NXP i.MX GPT variants, shineworld
lh133k MIPI SPI panel, Socionext Synquacer platforms, RK3588 PCIe,
ST M95640 EEPROM, and FSL DCP crypto variants, and Arm Cortex-R52
DT core:
- Improve the reserved-memory range allocation to maximize contiguous
space
- Use device_set_node() helper in place of open coding"
* tag 'devicetree-for-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (40 commits)
dt-bindings: interrupt-controller: add Ralink SoCs interrupt controller
dt-bindings: PCI: dwc: rockchip: Update for RK3588
dt-bindings: auxdisplay: holtek: Add missing type for "linux,no-autorepeat"
dt-bindings: input: mediatek,pmic-keys: Fix typo in "linux,keycodes" property name
dt-bindings: pwm: drop unneeded quotes
dt-bindings: crypto: drop unneeded quotes
dt-bindings: arm: socionext: add Synquacer platforms
dt-bindings: connector: usb: allow a single HS port
dt-bindings: bus: ti-sysc: fix typo
of: reserved_mem: Use stable allocation order
of: reserved_mem: Try to keep range allocations contiguous
dt-bindings: arm: drop unneeded quotes and use absolute /schemas path
dt-bindings: firmware: arm,scmi: drop unneeded quotes and use absolute /schemas path
dt-bindings: dvfs: drop unneeded quotes
dt-bindings: gpu: drop unneeded quotes
dt-bindings: i3c: silvaco,i3c-master: drop unneeded quotes
dt-bindings: rockchip: grf: drop unneeded quotes
dt-bindings: spmi: mtk,spmi-mtk-pmif: drop unneeded quotes
dt-bindings: Remove last usage of "binding" or "schema" in titles
dt-bindings: display: panel: mipi-dbi-spi: add spi-3wire property
...
Trogdor devices use firmware backed by TF-A instead of Qualcomm's
normal TZ. On TF-A we end up mapping memory as cacheable. Specifically,
you can see in Trogdor's TF-A code [1] in qti_sip_mem_assign() that we
call qti_mmap_add_dynamic_region() with MT_RO_DATA. This translates
down to MT_MEMORY instead of MT_NON_CACHEABLE or MT_DEVICE.
Let's allow devices like trogdor to be described properly by allowing
"dma-coherent" in the SCM node.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230616081440.v2.1.Ie79b5f0ed45739695c9970df121e11d724909157@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Arm SCMI updates for v6.5
Couple of main additions :-
1. Support for multiple SMC/HVC transports for SCMI:
Some platforms need to support multiple SCMI instances within
a platform(more commonly in a VM). The same SMC/HVC FID is used with
all the instances. The platform or the hypervisor needs a way to
distinguish among SMC/HVC calls made from different instances.
This change adds support for passing shmem channel address as the
parameters in the SMC/HVC call. The address is split into 4KB-page
and offset for simiplicity.
2. Addition od SCMI v3.2 explicit powercap enable/disable support:
SCMI v3.2 specification introduces support to disable powercapping
as a whole on the desired zones.
This change adds the needed support to the core SCMI powercap protocol,
exposing enable/disable protocol operations and then wiring up the new
operartions in the related powercap framework helpers.
* tag 'scmi-updates-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
powercap: arm_scmi: Add support for disabling powercaps on a zone
firmware: arm_scmi: Add Powercap protocol enable support
firmware: arm_scmi: Refactor the internal powercap get/set helpers
firmware: arm_scmi: Augment SMC/HVC to allow optional parameters
dt-bindings: firmware: arm,scmi: support for parameter in smc/hvc call
Link: https://lore.kernel.org/r/20230612121017.4108104-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 6.5, please pull the following:
- Krzysztof adds missing cache properties for the BCM63xx DSL routers
- Rafal relicenses a number of the BCM5301X DTS files to the GPL 2.0+ / MIT license,
and he fixes a number of Device Tree nodes warnings, adds MAC address
for all Luxul routers and adds Netgear R8000 Wi-Fi regulatory
information to the DTS
- Stanislav updates the "BCM mobile" SoCs DTS files to fix various
warnings
- Aurelien enables the BCM283x DTS files to be built with relocation
information to make them usable with DT overlays
- Christian fixes the Meraki DTS to have correct NAND ECC properties,
correct partition numbers and fixed-link node(s) properties
* tag 'arm-soc/for-6.5/devicetree' of https://github.com/Broadcom/stblinux: (33 commits)
ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
dt-bindings: firmware: brcm,kona-smc: convert to YAML
ARM: dts: BCM5301X: Add Netgear R8000 WiFi regulator mappings
dt-bindings: net: wireless: brcm,bcm4329-fmac: allow generic properties
dt-bindings: net: wireless: brcm,bcm4329-fmac: add BCM4366 binding
ARM: dts: BCM5301X: fix duplex-full => full-duplex
ARM: dts: BCM5301X: MR32: remove partition index numbers
ARM: dts: BCM5301X: MR26: MR32: remove bogus nand-ecc-algo property
dt-bindings: power: reset: bcm21664-resetmgr: convert to YAML
ARM: dts: bcm21664-garnet: use node labels
ARM: dts: bcm11351/21664: add UART, I2C node labels
ARM: dts: bcm-mobile: move status properties to the end of nodes
ARM: dts: bcm21664/23550: use CCU compatibles directly
ARM: dts: bcm-mobile: change "" includes to <> where applicable
ARM: dts: BCM5301X: Describe switch ports in the main DTS
ARM: dts: BCM5301X: Relicense Christian's code to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Drop invalid properties from Meraki MR32 keys
ARM: dts: BCM5301X: Drop invalid #usb-cells
dt-bindings: arm: bcm: Add bindings for Buffalo WZR-1166DHP(2)
ARM: dts: BCM5301X: Use updated "spi-gpio" binding properties
...
Link: https://lore.kernel.org/r/20230619134920.3384844-1-florian.fainelli@broadcom.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arm SCMI updates for v6.4
The main and only new addition this time around is the support for
unidirectional mailbox channels. SCMI communicates between the agent
and the platform using one bidirectional 'a2p' channel used by the agent
to send SCMI commands and synchronously receive the related replies, and
an optional 'p2a' unidirectional channel used to asynchronously receive
delayed responses and notifications emitted from the platform.
In order to support platforms that support only unidirectional mailbox
hardware channels, the existing bindings are extended to support the
same. Both bidirectional and unidirectional channels support for the
SCMI mailbox can coexist. The correct and effective combination of
defined 'mboxes' and 'shmem' descriptors determines the type of the
mailbox channel.
This also contains a fix for the transfers allocation on Rx channel
especially when the base protocol doesn't use Rx channel while some
of the protocols can have dedicated Rx channels.
* tag 'scmi-updates-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Add support for unidirectional mailbox channels
dt-bindings: firmware: arm,scmi: Support mailboxes unidirectional channels
firmware: arm_scmi: Fix xfers allocation on Rx channel
firmware: arm_scmi: Use the bitmap API to allocate bitmaps
firmware: arm_scmi: Fix device node validation for mailbox transport
firmware: arm_scmi: Fix raw coexistence mode behaviour on failure path
firmware: arm_scmi: Remove duplicate include header inclusion
firmware: arm_scmi: Return a literal instead of a variable
firmware: arm_scmi: Clean up a return statement in scmi_probe
Link: https://lore.kernel.org/r/20230417145743.1904318-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
SCMI defines two kinds of communication channels between the agent and the
platform: one bidirectional 'a2p' channel used by the agent to send SCMI
commands and synchronously receive the related replies, and an optional
'p2a' unidirectional channel used to asynchronously receive delayed
responses and notifications emitted from the platform.
When configuring an SCMI transport based on mailboxes, the current binding
supports only mailboxes providing bidirectional channels: in such a case
one mailbox channel can be easily assigned to each SCMI channel as above
described.
In case, instead, to have to deal with mailboxes providing only distinct
unidirectional channels, it becomes necessary to extend the binding in
order to be able to bind 2 distinct unidirectional mailbox channels to the
same SCMI 'a2p' channel.
Bidirectional and unidirectional channels support for the SCMI mailbox
transport can coexist by carefully considering the effective combination
of defined 'mboxes' and 'shmem' descriptors.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230404115026.2828149-2-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, there are lots of minor driver changes across SoC platforms
from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
These usually add support for additional chip variations in existing
drivers, but also add features or bugfixes.
The SCMI firmware subsystem gains a unified raw userspace interface
through debugfs, which can be used for validation purposes.
Newly added drivers include:
- New power management drivers for StarFive JH7110, Allwinner D1 and
Renesas RZ/V2M
- A driver for Qualcomm battery and power supply status
- A SoC device driver for identifying Nuvoton WPCM450 chips
- A regulator coupler driver for Mediatek MT81xxv"
* tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
power: supply: Introduce Qualcomm PMIC GLINK power supply
soc: apple: rtkit: Do not copy the reg state structure to the stack
soc: sunxi: SUN20I_PPU should depend on PM
memory: renesas-rpc-if: Remove redundant division of dummy
soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
MAINTAINERS: Update qcom CPR maintainer entry
dt-bindings: firmware: document Qualcomm SM8550 SCM
dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
soc: qcom: socinfo: Add support for new field in revision 17
soc: qcom: smd-rpm: Add IPQ9574 compatible
soc: qcom: pmic_glink: remove redundant calculation of svid
soc: qcom: stats: Populate all subsystem debugfs files
dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
soc: qcom: pmic_glink: Introduce altmode support
...
More Qualcomm driver updates for 6.3
The qcom_scm.h file is moved into firmware/qcom, to avoid having any
Qualcomm-specific files directly in include/linux.
Support for PMIC GLINK is introduced, which on newer Qualcomm platforms
provides an interface to the firmware implementing battery management
and USB Type-C handling. Together with the base driver comes the custom
altmode support driver.
SMD RPM gains support for IPQ9574, and socinfo is extended with support
for revision 17 of the information format and soc_id for IPQ5332 and
IPQ8064 are added.
The qcom_stats is changes not to fail when not all parts are
initialized.
* tag 'qcom-drivers-for-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
MAINTAINERS: Update qcom CPR maintainer entry
dt-bindings: firmware: document Qualcomm SM8550 SCM
dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
soc: qcom: socinfo: Add support for new field in revision 17
soc: qcom: smd-rpm: Add IPQ9574 compatible
soc: qcom: pmic_glink: remove redundant calculation of svid
soc: qcom: stats: Populate all subsystem debugfs files
dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
soc: qcom: pmic_glink: Introduce altmode support
soc: qcom: pmic_glink: Introduce base PMIC GLINK driver
dt-bindings: soc: qcom: Introduce PMIC GLINK binding
soc: qcom: dcc: Drop driver for now
Link: https://lore.kernel.org/r/20230210182242.2023901-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm driver updates for v6.3
This introduces a new driver for the Data Capture and Compare block,
which provides a mechanism for capturing hardware state (access MMIO
registers) either upon request of triggered automatically e.g. upon a
watchdog bite, for post mortem analysis.
The remote filesystem memory share driver gains support for having its
memory bound to more than a single VMID.
The SCM driver gains the minimal support needed to support a new
mechanism where secure world can put calls on hold and later request
them to be retried.
Support for the new SA8775P platform is added to rpmhpd, QDU1000 is
added to the SCM driver and a long list of platforms are added to the
socinfo driver. Support for socinfo data revision 16 is also introduced.
Lastly a driver to program the ramp controller in MSM8976 is introduced.
* tag 'qcom-drivers-for-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (33 commits)
firmware: qcom: scm: Add wait-queue handling logic
dt-bindings: firmware: qcom,scm: Add optional interrupt
Revert "dt-bindings: power: rpmpd: Add SM4250 support"
Revert "soc: qcom: rpmpd: Add SM4250 support"
soc: qcom: socinfo: Add a bunch of older SoCs
dt-bindings: arm: qcom,ids: Add a bunch of older SoCs
dt-bindings: arm: qcom,ids: Add QRD board ID
soc: qcom: socinfo: Fix soc_id order
dt-bindings: soc: qcom: smd-rpm: Exclude MSM8936 from glink-channels
dt-bindings: firmware: qcom: scm: Separate VMIDs from header to bindings
soc: qcom: rmtfs: Optionally map RMTFS to more VMs
dt-bindings: reserved-memory: rmtfs: Make qcom,vmid an array
dt-bindings: firmware: scm: Add QDU1000/QRU1000 compatible
dt-bindings: firmware: qcom,scm: narrow clocks and interconnects
dt-bindings: firmware: qcom,scm: document MSM8226 clocks
soc: qcom: ramp_controller: Make things static
soc: qcom: rmphpd: add power domains for sa8775p
dt-bindings: power: qcom,rpmpd: document sa8775p
PM: AVS: qcom-cpr: Fix an error handling path in cpr_probe()
soc: qcom: dcc: rewrite description of dcc sysfs files
...
Link: https://lore.kernel.org/r/20230126163008.3676950-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The SCMI protocol child nodes are missing any constraints on unknown
properties. Specifically, either 'unevaluatedProperties' or
'additionalProperties' is needed. The current structure with a regex
match for all child nodes doesn't work for this purpose, so let's move
the common properties '$defs' entry which each specific protocol node
can reference and set 'unevaluatedProperties: false'.
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20230124222023.316089-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Pull gpio updates from Bartosz Golaszewski:
"We have a single new driver, support for a bunch of new models,
improvements in drivers and core gpiolib code as well device-tree
bindings changes.
Summary:
New driver:
- IMX System Controller Unit GPIOs
GPIO core:
- add fdinfo output for the GPIO character device file descriptors
(allows user-space to determine which processes own which GPIO
lines)
- improvements to OF GPIO code
- new quirk for Asus UM325UAZ in gpiolib-acpi
- new quirk for Freescale SPI in gpiolib-of
Driver improvements:
- add a new macro that reduces the amount of boilerplate code in ISA
drivers and use it in relevant drivers
- support two new models in gpio-pca953x
- support new model in gpio-f7188x
- convert more drivers to use immutable irq chips
- other minor tweaks
Device-tree bindings:
- add DT bindings for gpio-imx-scu
- convert Xilinx GPIO bindings to YAML
- reference the properties from the SPI peripheral device-tree
bindings instead of providing custom ones in the GPIO controller
document
- add parsing of GPIO hog nodes to the DT bindings for gpio-mpfs-gpio
- relax the node name requirements in gpio-stmpe
- add new models for gpio-rcar and gpio-pxa95xx
- add a new vendor prefix: Diodes (for Diodes, Inc.)
Misc:
- pulled in the immutable branch from the x86 platform drivers tree
including support for a new simatic board that depends on GPIO
changes"
* tag 'gpio-updates-for-v6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (36 commits)
gpio: tc3589x: Make irqchip immutable
gpiolib: cdev: add fdinfo output for line request file descriptors
gpio: twl4030: Reorder functions which allows to drop a forward declaraion
gpiolib: fix OOB access in quirk callbacks
gpiolib: of: factor out conversion from OF flags
gpiolib: rework quirk handling in of_find_gpio()
gpiolib: of: make Freescale SPI quirk similar to all others
gpiolib: of: do not ignore requested index when applying quirks
gpio: ws16c48: Ensure number of irq matches number of base
gpio: 104-idio-16: Ensure number of irq matches number of base
gpio: 104-idi-48: Ensure number of irq matches number of base
gpio: 104-dio-48e: Ensure number of irq matches number of base
counter: 104-quad-8: Ensure number of irq matches number of base
isa: Introduce the module_isa_driver_with_irq helper macro
gpio: pca953x: Add support for PCAL6534
gpio: pca953x: Swap if statements to save later complexity
gpio: pca953x: Fix pca953x_gpio_set_pull_up_down()
dt-bindings: gpio: pca95xx: add entry for pcal6534 and PI4IOE5V6534Q
dt-bindings: vendor-prefixes: add Diodes
gpio: mt7621: Switch to use platform_get_irq() function
...
Pull ARM DT updates from Arnd Bergmann:
"As usual, the bulk of the changes for the SoC tree are devicetree file
updates, and most of these changes are for 64-bit embedded machines.
As before, there are a ton of style cleanups, and additional hardware
support for existing machines.
Looking only at the new SoC, the notable additions are:
- A whole family of Broadcom broadband SoCs, both 32-bit and 64-bit:
BCM63178, BCM63158, BCM4912, BCM6858, BCM6878, BCM6846, BCM63146,
BCM6856, BCM6855, BCM6756, BCM63148, and BCM6813. Each SoC comes
with a corresponding reference board.
- The new NXP i.MX93 SoC, the follow-up to the popular i.MX6 and
i.MX8 embedded SoCs, now using Cortex-A55 cores and the Ethos-U65
NPU.
- Qualcomm Snapdragon 8cx Gen3 (SC8280XP), the current high end of
Arm based Laptop SoCs, and its automotive cousin, the SA8540P. The
SC8280XP is used in the Lenovo Thinkpad X13s laptop that also gets
added here in addition to the reference boards.
- Allwinner H616, a newer version of the H6 SoC, targeted at
Set-top-box applications. It comes with dts files for the Orange Pi
zero2 single-board computer and the X96 Mate set-top-box
- Marvell Prestera 98DX2530 (AlleyCat5), a network switch chip in the
Armada SoC family based on the Cortex-A55 core.
New machines based on previously supported SoCs include:
- Several new machines on NXP i.MX platforms: multiple Toradex
Colibri boards using the "Iris" and "Ixora" carriers, DH
electronics i.MX8M Plus DHCOM and PDK2, TQ-Systems TQMa8MPQL, and
phytech phyBOARD-Polis-i.MX8MM.
- Google Chameleon v3 FPGA board based on Intel Arria10 and Stratix
10 Software Virtual platform, both in the SoCFPGA platform.
- Two new wireless devices based on Broadcom SoCs: The Asus GT-AX6000
Router and the Cisco Meraki MR26 access point
- Improved Chromebook support for both the Mediatek and Qualcomm SoC
families brought added machines: Acer Chromebook 514 (MT8192), Acer
Chromebook Spin 513 (MT8195) and a couple of SC7180 based machines
including the Lenovo IdeaPad Chromebook Duet 3.
- Xiaomi Mi Mix2s, LG G7 and LG V35 are mobile phones based on
Qualcomm SDM845, while Mi 5s Plus is based on MSM8996.
- Finally, there are a few development board on other chips: PCB8309
(Microchip lan966x), Radxa Rock Pi S (Rockchips RK3308) DH DRC
Compact (ST STM32MP1) and Inforce IFC6560 (Qualcomm SDM660)"
* tag 'arm-dt-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (829 commits)
dt-bindings: soc: bcm: use absolute path to other schema
dt-bindings: soc: bcm: drop quotes when not needed
dt-bindings: soc: microchip: use absolute path to other schema
dt-bindings: soc: microchip: drop quotes when not needed
ARM: dts: lan966x: keep lan966 entries alphabetically sorted
ARM: dts: lan966x: add support for pcb8309
dt-bindings: arm: at91: add lan966 pcb8309 board
ARM: dts: lan966x: Enable network driver on pcb8291
ARM: dts: lan966x: Disable can0 on pcb8291
ARM: dts: lan966x: Add gpio-restart
dt-bindings: arm: aspeed: add Aspeed Evaluation boards
arm64: dts: qcom: Add support for Xiaomi Mi Mix2s
dt-bindings: arm: qcom: Add Xiaomi Mi Mix2s bindings
dt-bindings: arm: qcom: Document lg,judyln and lg,judyp devices
dt-bindings: arm: qcom: add missing SM6350 board compatibles
dt-bindings: arm: qcom: add missing SM6125 board compatibles
dt-bindings: arm: qcom: add missing SDM845 board compatibles
dt-bindings: arm: qcom: add missing SDM636 board compatibles
dt-bindings: arm: qcom: add missing SDM630 board compatibles
dt-bindings: arm: qcom: add missing QCS404 board compatibles
...
Qualcomm driver updates for v5.20
This introduces a new driver that requests interconnect bandwidth based
on throughput measurements of the bwmon hardware blocks found associated
with, among other things, the CPU subsystem on many Qualcomm platforms.
It introduces support for the SCM wrapper driver to vote for
interconnect bandwidth for operations that needs bandwidth to the crypto
engine. This ensures both performance and guards against issues caused
by lacking votes for this path.
The socinfo driver gains knowledge about the SC7180P SoC.
It contains a range of fixes for spelling mistakes, refcount leaks in
various drivers and removes some redundant code from the apr remove
path.
The SCM DT bindings are updated to declare support for QCS404, SM6125
and SDX65.
The command db driver has a strncpy() converted to strscpy_pad() and
then back again with proper documentation to why this was the right API.
* tag 'qcom-drivers-for-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: icc-bwmon: Add bandwidth monitoring driver
dt-bindings: interconnect: qcom,msm8998-cpu-bwmon: add BWMON device
soc/qcom: Make QCOM_RPMPD select PM_GENERIC_DOMAINS/_OF
soc: qcom: aoss: Fix refcount leak in qmp_cooling_devices_register
soc: qcom: llcc: Fix syntax errors in comments
soc: qcom: ocmem: Fix refcount leak in of_get_ocmem
dt-bindings: soc: qcom,wcnss: remove unneeded ref for names
firmware: qcom_scm: Add bw voting support to the SCM interface
dt-bindings: firmware: qcom-scm: Add interconnects property
soc: qcom: cmd-db: replace strscpy_pad() with strncpy()
dt-bindings: firmware: scm: Add compatible for SDX65
dt-bindings: arm: qcom: switch maintainer to Bjorn
soc: qcom: rpmhpd: fix typos in comment
soc: qcom: correct kerneldoc
soc: qcom: cmd-db: replace strncpy() with strscpy_pad()
firmware: qcom_scm-legacy: correct kerneldoc
dt-bindings: firmware: document Qualcomm QCS404 and SM6125 SCM
soc: qcom: apr: Drop redundant check in .remove()
firmware: qcom_scm: drop unexpected word "the"
soc: qcom: socinfo: Add an ID for sc7180P
Link: https://lore.kernel.org/r/20220712021830.1271398-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In order to replace the fsl,scu txt file from bindings/arm/freescale,
we need to split it between the right subsystems. This patch adds the
fsl,scu.yaml in the firmware bindings folder. This one is only for
the main SCU node. The old txt file will be removed only after all
the child nodes have been properly switch to yaml.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull devicetree updates from Rob Herring:
- Add Krzysztof Kozlowski as co-maintainer for DT bindings providing
much needed help.
- DT schema validation now takes DTB files as input rather than
intermediate YAML files. This decouples the validation from the
source level syntax information. There's a bunch of schema fixes as a
result of switching to DTB based validation which exposed some errors
and incomplete schemas and examples.
- Kbuild improvements to explicitly warn users running 'make
dt_binding_check' on missing yamllint
- Expand DT_SCHEMA_FILES kbuild variable to take just a partial
filename or path instead of the full path to 1 file.
- Convert various bindings to schema format: mscc,vsc7514-switch,
multiple GNSS bindings, ahci-platform, i2c-at91, multiple UFS
bindings, cortina,gemini-sata-bridge, cortina,gemini-ethernet, Atmel
SHA, Atmel TDES, Atmel AES, armv7m-systick, Samsung Exynos display
subsystem, nuvoton,npcm7xx-timer, samsung,s3c2410-i2c, zynqmp_dma,
msm/mdp4, rda,8810pl-uart
- New schemas for u-boot environment variable partition, TI clksel
- New compatible strings for Renesas RZ/V2L SoC
- Vendor prefixes for Xen, HPE, deprecated Synopsys, deprecated
HiSilicon
- Add/fix schemas for QEMU Arm 'virt' machine
- Drop unused of_alias_get_alias_list() function
- Add a script to check DT unittest EXPECT message output. Pass
messages also now print by default at PR_INFO level to help test
automation.
* tag 'devicetree-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (96 commits)
dt-bindings: kbuild: Make DT_SCHEMA_LINT a recursive variable
dt-bindings: nvmem: add U-Boot environment variables binding
dt-bindings: ufs: qcom: Add SM6350 compatible string
dt-bindings: dmaengine: sifive,fu540-c000: include generic schema
dt-bindings: gpio: pca95xx: drop useless consumer example
Revert "of: base: Introduce of_alias_get_alias_list() to check alias IDs"
dt-bindings: virtio,mmio: Allow setting devices 'dma-coherent'
dt-bindings: gnss: Add two more chips
dt-bindings: gnss: Rewrite sirfstar binding in YAML
dt-bindings: gnss: Modify u-blox to use common bindings
dt-bindings: gnss: Rewrite common bindings in YAML
dt-bindings: ata: ahci-platform: Add rk3568-dwc-ahci compatible
dt-bindings: ata: ahci-platform: Add power-domains property
dt-bindings: ata: ahci-platform: Convert DT bindings to yaml
dt-bindings: kbuild: Use DTB files for validation
dt-bindings: kbuild: Pass DT_SCHEMA_FILES to dt-validate
dt-bindings: Add QEMU virt machine compatible
dt-bindings: arm: Convert QEMU fw-cfg to DT schema
dt-bindings: i2c: at91: Add SAMA7G5 compatible strings list
dt-bindings: i2c: convert i2c-at91 to json-schema
...
SCMI protocols in the platform can optionally signal to the OSPM agent
the expected execution latency for a specific resource/operation pair.
Introduce an SCMI system wide optional property to describe a global time
threshold which can be configured on a per-platform base to determine the
opportunity, or not, for an SCMI command advertised to have a higher
latency than the threshold, to be considered for atomic operations:
high-latency SCMI synchronous commands should be preferably issued in the
usual non-atomic mode.
Link: https://lore.kernel.org/r/20220217131234.50328-5-cristian.marussi@arm.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Arm SCMI firmware interface updates for v5.17
Couple of main additions:
- Support for OPTEE based SCMI transport to enable using SCMI service
provided by OPTEE on some platforms
- Support for atomic SCMI transports which enables few SCMI transactions
to be completed in atomic context. This involves other refactoring work
associated with it. It also marks SMC and OPTEE as atomic transport as
the commands are completed once the return
Other changes involves some trace and log enhancements and a miscellaneous
bug fix.
* tag 'scmi-updates-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Add new parameter to mark_txdone
firmware: arm_scmi: Add atomic mode support to smc transport
firmware: arm_scmi: Add support for atomic transports
firmware: arm_scmi: Make optee support sync_cmds_completed_on_ret
firmware: arm_scmi: Make smc support sync_cmds_completed_on_ret
firmware: arm_scmi: Add sync_cmds_completed_on_ret transport flag
firmware: arm_scmi: Make smc transport use common completions
firmware: arm_scmi: Add configurable polling mode for transports
firmware: arm_scmi: Use new trace event scmi_xfer_response_wait
include: trace: Add new scmi_xfer_response_wait event
firmware: arm_scmi: Refactor message response path
firmware: arm_scmi: Set polling timeout to max_rx_timeout_ms
firmware: arm_scmi: Perform earlier cinfo lookup call in do_xfer
firmware: arm_scmi: optee: Drop the support for the OPTEE shared dynamic buffer
firmware: arm_scmi: optee: Fix missing mutex_init()
firmware: arm_scmi: Make virtio Version_1 compliance optional
firmware: arm_scmi: Add optee transport
dt-bindings: arm: Add OP-TEE transport for SCMI
firmware: arm_scmi: Review some virtio log messages
The 'phandle-array' type is a bit ambiguous. It can be either just an
array of phandles or an array of phandles plus args. Many schemas for
phandle-array properties aren't clear in the schema which case applies
though the description usually describes it.
The array of phandles case boils down to needing:
items:
maxItems: 1
The phandle plus args cases should typically take this form:
items:
- items:
- description: A phandle
- description: 1st arg cell
- description: 2nd arg cell
With this change, some examples need updating so that the bracketing of
property values matches the schema.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220119015038.2433585-1-robh@kernel.org
