Prior to LLVM 15.0.0, LLVM's integrated assembler would incorrectly
byte-swap NOP when compiling for big-endian, and the resulting series of
bytes happened to match the encoding of FNMADD S21, S30, S0, S0.
This went unnoticed until commit:
34f66c4c4d ("arm64: Use a positive cpucap for FP/SIMD")
Prior to that commit, the kernel would always enable the use of FPSIMD
early in boot when __cpu_setup() initialized CPACR_EL1, and so usage of
FNMADD within the kernel was not detected, but could result in the
corruption of user or kernel FPSIMD state.
After that commit, the instructions happen to trap during boot prior to
FPSIMD being detected and enabled, e.g.
| Unhandled 64-bit el1h sync exception on CPU0, ESR 0x000000001fe00000 -- ASIMD
| CPU: 0 PID: 0 Comm: swapper Not tainted 6.6.0-rc3-00013-g34f66c4c4d55 #1
| Hardware name: linux,dummy-virt (DT)
| pstate: 400000c9 (nZcv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
| pc : __pi_strcmp+0x1c/0x150
| lr : populate_properties+0xe4/0x254
| sp : ffffd014173d3ad0
| x29: ffffd014173d3af0 x28: fffffbfffddffcb8 x27: 0000000000000000
| x26: 0000000000000058 x25: fffffbfffddfe054 x24: 0000000000000008
| x23: fffffbfffddfe000 x22: fffffbfffddfe000 x21: fffffbfffddfe044
| x20: ffffd014173d3b70 x19: 0000000000000001 x18: 0000000000000005
| x17: 0000000000000010 x16: 0000000000000000 x15: 00000000413e7000
| x14: 0000000000000000 x13: 0000000000001bcc x12: 0000000000000000
| x11: 00000000d00dfeed x10: ffffd414193f2cd0 x9 : 0000000000000000
| x8 : 0101010101010101 x7 : ffffffffffffffc0 x6 : 0000000000000000
| x5 : 0000000000000000 x4 : 0101010101010101 x3 : 000000000000002a
| x2 : 0000000000000001 x1 : ffffd014171f2988 x0 : fffffbfffddffcb8
| Kernel panic - not syncing: Unhandled exception
| CPU: 0 PID: 0 Comm: swapper Not tainted 6.6.0-rc3-00013-g34f66c4c4d55 #1
| Hardware name: linux,dummy-virt (DT)
| Call trace:
| dump_backtrace+0xec/0x108
| show_stack+0x18/0x2c
| dump_stack_lvl+0x50/0x68
| dump_stack+0x18/0x24
| panic+0x13c/0x340
| el1t_64_irq_handler+0x0/0x1c
| el1_abort+0x0/0x5c
| el1h_64_sync+0x64/0x68
| __pi_strcmp+0x1c/0x150
| unflatten_dt_nodes+0x1e8/0x2d8
| __unflatten_device_tree+0x5c/0x15c
| unflatten_device_tree+0x38/0x50
| setup_arch+0x164/0x1e0
| start_kernel+0x64/0x38c
| __primary_switched+0xbc/0xc4
Restrict CONFIG_CPU_BIG_ENDIAN to a known good assembler, which is
either GNU as or LLVM's IAS 15.0.0 and newer, which contains the linked
commit.
Closes: https://github.com/ClangBuiltLinux/linux/issues/1948
Link: 1379b15099
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Cc: stable@vger.kernel.org
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20231025-disable-arm64-be-ias-b4-llvm-15-v1-1-b25263ed8b23@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit d2b310b023 ("ARM: debug: Use generic 8250 debug_ll for omap2 and
omap3/4/5 common uarts") adds address definitions of DEBUG_UART_PHYS for
OMAP2, OMAP3, OMAP4 and OMAP5 in ./arch/arm/Kconfig.debug.
These definitions depend on DEBUG_OMAP{2,3,4,5}UART{1,2}; however, only
DEBUG_OMAP2UART{1,2} are defined in ./arch/arm/Kconfig.debug, and
DEBUG_OMAP{3,4,5}UART{1,2} are not defined. Hence, the script
./scripts/checkkconfigsymbols.py warns here on non-existing symbols.
Simply reuse the config DEBUG_OMAP2UART{1,2}; there is no need to define
separate config symbols for OMAP{3,4,5}. So, just delete the dead
references to DEBUG_OMAP{3,4,5}UART{1,2}.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20231025112136.3445-1-lukas.bulwahn@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Renesas fixes for v6.6 (take three)
- Sort out a few Kconfig dependency issues for the rich set of RISC-V
non-coherent DMA support.
* tag 'renesas-fixes-for-v6.6-tag3' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
soc: renesas: ARCH_R9A07G043 depends on !RISCV_ISA_ZICBOM
riscv: only select DMA_DIRECT_REMAP from RISCV_ISA_ZICBOM and ERRATA_THEAD_PBMT
riscv: RISCV_NONSTANDARD_CACHE_OPS shouldn't depend on RISCV_DMA_NONCOHERENT
Link: https://lore.kernel.org/r/cover.1698312384.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
commit ef8dd01538 ("genirq/msi: Make interrupt allocation less
convoluted"), reworked the code so that the x86 specific quirk for affinity
setting of non-maskable PCI/MSI interrupts is not longer activated if
necessary.
This could be solved by restoring the original logic in the core MSI code,
but after a deeper analysis it turned out that the quirk flag is not
required at all.
The quirk is only required when the PCI/MSI device cannot mask the MSI
interrupts, which in turn also prevents reservation mode from being enabled
for the affected interrupt.
This allows ot remove the NOMASK quirk bit completely as msi_set_affinity()
can instead check whether reservation mode is enabled for the interrupt,
which gives exactly the same answer.
Even in the momentary non-existing case that the reservation mode would be
not set for a maskable MSI interrupt this would not cause any harm as it
just would cause msi_set_affinity() to go needlessly through the
functionaly equivalent slow path, which works perfectly fine with maskable
interrupts as well.
Rework msi_set_affinity() to query the reservation mode and remove all
NOMASK quirk logic from the core code.
[ tglx: Massaged changelog ]
Fixes: ef8dd01538 ("genirq/msi: Make interrupt allocation less convoluted")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231026032036.2462428-1-den@valinux.co.jp
One new board the Turing RK1 system on module.
Support for DFI (DDR performance monitoring) for rk3588, rk3568 and an
enable-fix for rk3399 as well as some small fixups for the RGB30 handheld
(non-existent uart and better vpll frequency).
* tag 'v6.7-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add Turing RK1 SoM support
dt-bindings: arm: rockchip: Add Turing RK1
dt-bindings: vendor-prefixes: add turing
arm64: dts: rockchip: Add DFI to rk3588s
arm64: dts: rockchip: Add DFI to rk356x
arm64: dts: rockchip: Always enable DFI on rk3399
arm64: dts: rockchip: Remove UART2 from RGB30
arm64: dts: rockchip: Update VPLL Frequency for RGB30
Link: https://lore.kernel.org/r/2777623.BEx9A2HvPv@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
TI K3 device-tree updates for v6.7 - part 2
Second round of few DT updates for K3 platforms. These have been in
linux-next for a few days without issues. Most of the additions is for
newer AM62P SoC dtsi bringing support on par with rest of AM62x family.
New features:
AM62P SoCs:
Support for wide range of peripherals such as eMMC/SD,
CPSW Ethernet, OSPI, etc similar to AM62
J721s2/J784s4/AM69 SoCs:
Display support via DP and HDMI interfaces and associated SerDes support
AM654 EVM/IDK:
ICSSG/PRU based industrial Ethernet support
* tag 'ti-k3-dt-for-v6.7-part2' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
arm64: dts: ti: k3-am654-idk: Add ICSSG Ethernet ports
arm64: dts: ti: k3-am654-icssg2: add ICSSG2 Ethernet support
arm64: dts: ti: k3-am65-main: Add ICSSG IEP nodes
arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM
arm64: dts: ti: k3-am62p: Add nodes for more IPs
arm64: dts: ti: k3-am69-sk: Add DP and HDMI support
arm64: dts: ti: k3-j784s4-evm: Enable DisplayPort-0
arm64: dts: ti: k3-j784s4-main: Add DSS and DP-bridge node
arm64: dts: ti: k3-j784s4-main: Add WIZ and SERDES PHY nodes
arm64: dts: ti: k3-j784s4-main: Add system controller and SERDES lane mux
Link: https://lore.kernel.org/r/35a3c4c9-5c1b-4891-9ea2-e3f648a9afe0@ti.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM-based SoCs changes for 6.7,
please pull the following:
- Rafal makes a number of updates to the BCM5301X (Northstar) SoCs DTS
to set MAC addresses for D-LInk DIR-885L, Asus, RT-AC87U, he
relicenses parts of the DTSI to GPL 2.0+ / MIT, and finally fixes a
number of Ethernet switch ports properties to enable/disable ports
adequately.
* tag 'arm-soc/for-6.7/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Set switch ports for Linksys EA9200
ARM: dts: BCM5301X: Set fixed-link for extra Netgear R8000 CPU ports
ARM: dts: BCM5301X: Explicitly disable unused switch CPU ports
ARM: dts: BCM5301X: Relicense Vivek's code to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Relicense Felix's code to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Set MAC address for Asus RT-AC87U
ARM: dts: BCM5301X: Set MACs for D-Link DIR-885L
Link: https://lore.kernel.org/r/20231024155927.977263-1-florian.fainelli@broadcom.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Samsung DTS ARM changes for v6.7, part two
Two minor improvements for Midas boards (Exynos4412, e.g. Samsung Galaxy S3):
1. Correct the middle hardware key to emit KEY_OK instead of KEY_MENU,
because there is already separate touchkey providing KEY_MENU and
both label and node name suggests this should be KEY_OK.
2. Use defines for other key input constants.
* tag 'samsung-dt-6.7-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: samsung: exynos4412-midas: use Linux event codes for input keys
ARM: dts: samsung: exynos4412-midas: fix key-ok event code
Link: https://lore.kernel.org/r/20231024132615.65609-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The superhyway bus driver was only referenced on SH4-202, which is now gone,
so remove it all as well.
I could find no trace of anything ever calling superhyway_register_driver(),
not in the git history but also not on the web, so I assume this has never
served any purpose on mainline kernels.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/20230914155523.3839811-3-arnd@kernel.org
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
This reverts the following commits:
commit 53313ed25b ("dt-bindings: marvell: Add Marvell MV88E6060 DSA schema")
commit 0f35369b4e ("dt-bindings: marvell: Rewrite MV88E6xxx in schema")
commit 605a5f5d40 ("ARM64: dts: marvell: Fix some common switch mistakes")
commit bfedd84236 ("ARM: dts: nxp: Fix some common switch mistakes")
commit 2b83557a58 ("ARM: dts: marvell: Fix some common switch mistakes")
commit ddae07ce9b ("dt-bindings: net: mvusb: Fix up DSA example")
commit b5ef61718a ("dt-bindings: net: dsa: Require ports or ethernet-ports")
As repoted by Vladimir, it breaks boot on the Turris MOX board.
Link: https://lore.kernel.org/all/20231025093632.fb2qdtunzaznd73z@skbuf/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kernel-internal prototypes, references to current_thread_info()
and code hidden behind a CONFIG_HEXAGON_ARCH_VERSION switch are
certainly not usable in userspace, so this should not reside
in a uapi header. Move the code into an internal version of
ptrace.h instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
If the cmma no-dat feature is available the kernel page tables are walked
to identify and mark all pages which are used for address translation (all
region, segment, and page tables). In a subsequent loop all other pages are
marked as "no-dat" pages with the ESSA instruction.
This information is visible to the hypervisor, so that the hypervisor can
optimize purging of guest TLB entries. All pages used for swapper_pg_dir
and invalid_pg_dir are incorrectly marked as no-dat, which in turn can
result in incorrect guest TLB flushes.
Fix this by marking those pages correctly as being used for DAT.
Cc: <stable@vger.kernel.org>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
If the cmma no-dat feature is available the kernel page tables are walked
to identify and mark all pages which are used for address translation (all
region, segment, and page tables). In a subsequent loop all other pages are
marked as "no-dat" pages with the ESSA instruction.
This information is visible to the hypervisor, so that the hypervisor can
optimize purging of guest TLB entries. The initial loop however is
incorrect: only the first three of the four pages which belong to segment
and region tables will be marked as being used for DAT. The last page is
incorrectly marked as no-dat.
This can result in incorrect guest TLB flushes.
Fix this by simply marking all four pages.
Cc: <stable@vger.kernel.org>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Function paicrypt_event_init() initializes the PMU device driver
specific details for an event. It is called once per event creation.
The function paicrypt_event_init() is not necessarily executed on
that CPU the event will be used for.
When an event is activated, function paicrypt_start() is used to
start the event on that CPU.
The per CPU data structure struct paicrypt_map has a pointer to
the event which is active for a particular CPU. This pointer is
set in function paicrypt_start() to point to the currently installed
event. There is no need to also set this pointer in function
paicrypt_event_init() where is might be assigned to the wrong CPU.
Therefore remove this assignment in paicrypt_event_init().
Acked-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Event count value is initialized and set to zero in function
paicrypt_start(). This function is called once per CPU when an
event is started on that CPU. This leads to event count value
being set to zero as many times as there are online CPUs.
This is not necessary. The event count value is bound to the event
and it is sufficient to initialize the event counter once at
event creation time. This is done when the event structure
is dynamicly allocated with __GFP_ZERO flag. This sets
member count to zero.
Acked-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Use define PERF_ATTACH_TASK bit in event->attach_state to determine
system wide invocation or per task invocation in event initialization.
This bit is set in common code and before calling PMU device driver
specific event initialization.
It is set once and never changes. It is save to use and also in
sync with other PMU specific code.
No functional change.
Acked-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
If the cmma no-dat feature is available all pages that are not used for
dynamic address translation are marked as "no-dat" with the ESSA
instruction. This information is visible to the hypervisor, so that the
hypervisor can optimize purging of guest TLB entries. This also means that
pages which are used for dynamic address translation must not be marked as
"no-dat", since the hypervisor may then incorrectly not purge guest TLB
entries.
Region, segment, and page tables allocated within the gmap code are
incorrectly marked as "no-dat", since an explicit call to
arch_set_page_dat() is missing, which would remove the "no-dat" mark.
In order to fix this add a new gmap_alloc_crst() function which should
be used to allocate region and segment tables, and which also calls
arch_set_page_dat().
Also add the arch_set_page_dat() call to page_table_alloc_pgste().
Cc: <stable@vger.kernel.org>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Fix some errors in the Marvell MV88E6xxx switch descriptions:
- The top node had no address size or cells.
- switch0@0 is not OK, should be ethernet-switch@0.
- ports should be ethernet-ports
- port@0 should be ethernet-port@0
- PHYs should be named ethernet-phy@
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some errors in the Marvell MV88E6xxx switch descriptions:
- switch0@0 is not OK, should be ethernet-switch@0
- ports should be ethernet-ports
- port should be ethernet-port
- phy should be ethernet-phy
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some errors in the Marvell MV88E6xxx switch descriptions:
- The top node had no address size or cells.
- switch0@0 is not OK, should be ethernet-switch@0.
- The ports node should be named ethernet-ports
- The ethernet-ports node should have port@0 etc children, no
plural "ports" in the children.
- Ports should be named ethernet-port@0 etc
- PHYs should be named ethernet-phy@0 etc
This serves as an example of fixes needed for introducing a
schema for the bindings, but the patch can simply be applied.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit 9fee28baa6 ("powerpc: implement the new page table range
API") we added set_ptes to powerpc architecture. The implementation
included calling arch_enter/leave_lazy_mmu() calls.
The patch removes the usage of arch_enter/leave_lazy_mmu() because
set_pte is not supposed to be used when updating a pte entry. Powerpc
architecture uses this rule to skip the expensive tlb invalidate which
is not needed when you are setting up the pte for the first time. See
commit 56eecdb912 ("mm: Use ptep/pmdp_set_numa() for updating
_PAGE_NUMA bit") for more details
The patch also makes sure we are not using the interface to update a
valid/present pte entry by adding VM_WARN_ON check all the ptes we
are setting up. Furthermore, we add a comment to set_pte_filter to
clarify it can only update folio-related flags and cannot filter
pfn specific details in pte filtering.
Removal of arch_enter/leave_lazy_mmu() also will avoid nesting of
these functions that are not supported. For ex:
remap_pte_range()
-> arch_enter_lazy_mmu()
-> set_ptes()
-> arch_enter_lazy_mmu()
-> arch_leave_lazy_mmu()
-> arch_leave_lazy_mmu()
Fixes: 9fee28baa6 ("powerpc: implement the new page table range API")
Signed-off-by: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20231024143604.16749-1-aneesh.kumar@linux.ibm.com
Since below commit, address mapping for vmemmap has changed for Radix
MMU, where address mapping is stored in kernel page table itself,
instead of earlier used 'vmemmap_list'.
commit 368a0590d9 ("powerpc/book3s64/vmemmap: switch radix to use
a different vmemmap handling function")
Hence with upstream kernel, in case of Radix MMU, makedumpfile fails
to do address translation for vmemmap addresses, as it depended on
vmemmap_list, which can now be empty.
While fixing the address translation in makedumpfile, it was identified
that currently makedumpfile cannot distinguish between Hash MMU and
Radix MMU, unless VMLINUX is passed with -x flag to makedumpfile. And
hence fails to assign offsets and shifts correctly (such as in L4 to
PGDIR offset calculation in makedumpfile).
For getting the MMU, makedumpfile uses `cur_cpu_spec.mmu_features`.
Add `cur_cpu_spec` symbol and offset of `mmu_features` in the `cpu_spec`
struct, to VMCOREINFO, so that makedumpfile can assign the offsets
correctly, without needing a VMLINUX.
Also, even along with `cur_cpu_spec->mmu_features` makedumpfile has to
depend on the 'MMU_FTR_TYPE_RADIX' flag in mmu_features, implying kernel
developers need to be cautious of changes to 'MMU_FTR_*' defines.
A more stable approach was suggested in the below thread by contributors:
https://lore.kernel.org/linuxppc-dev/20230920105706.853626-1-adityag@linux.ibm.com/
The suggestion was to add whether 'RADIX_MMU' is enabled in vmcoreinfo
This patch also implements the suggestion, by adding 'RADIX_MMU' in
vmcoreinfo, which makedumpfile can use to get whether the crashed system
had RADIX MMU (in which case 'NUMBER(RADIX_MMU)=1') or not (in which
case 'NUMBER(RADIX_MMU)=0')
Fixes: 368a0590d9 ("powerpc/book3s64/vmemmap: switch radix to use a different vmemmap handling function")
Reported-by: Sachin Sant <sachinp@linux.ibm.com>
Signed-off-by: Aditya Gupta <adityag@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20231023072612.50874-1-adityag@linux.ibm.com
This reverts commit 7135b921b3.
I applied this commit prematurely while there was still discussion
ongoing. Revert it so the final patch can be applied cleanly.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
KVM does not yet support userspace modifying PMCR_EL0.N (With
the previous patch, KVM ignores what is written by userspace).
Add support userspace limiting PMCR_EL0.N.
Disallow userspace to set PMCR_EL0.N to a value that is greater
than the host value as KVM doesn't support more event counters
than what the host HW implements. Also, make this register
immutable after the VM has started running. To maintain the
existing expectations, instead of returning an error, KVM
returns a success for these two cases.
Finally, ignore writes to read-only bits that are cleared on
vCPU reset, and RES{0,1} bits (including writable bits that
KVM doesn't support yet), as those bits shouldn't be modified
(at least with the current KVM).
Co-developed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
Link: https://lore.kernel.org/r/20231020214053.2144305-8-rananta@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
For unimplemented counters, the registers PM{C,I}NTEN{SET,CLR}
and PMOVS{SET,CLR} are expected to have the corresponding bits RAZ.
Hence to ensure correct KVM's PMU emulation, mask out the RES0 bits.
Defer this work to the point that userspace can no longer change the
number of advertised PMCs.
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20231020214053.2144305-7-rananta@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
For unimplemented counters, the bits in PM{C,I}NTEN{SET,CLR} and
PMOVS{SET,CLR} registers are expected to RAZ. To honor this,
explicitly implement the {get,set}_user functions for these
registers to mask out unimplemented counters for userspace reads
and writes.
Co-developed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
Link: https://lore.kernel.org/r/20231020214053.2144305-6-rananta@google.com
[Oliver: drop unnecessary locking]
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
The number of PMU event counters is indicated in PMCR_EL0.N.
For a vCPU with PMUv3 configured, the value is set to the same
value as the current PE on every vCPU reset. Unless the vCPU is
pinned to PEs that has the PMU associated to the guest from the
initial vCPU reset, the value might be different from the PMU's
PMCR_EL0.N on heterogeneous PMU systems.
Fix this by setting the vCPU's PMCR_EL0.N to the PMU's PMCR_EL0.N
value. Track the PMCR_EL0.N per guest, as only one PMU can be set
for the guest (PMCR_EL0.N must be the same for all vCPUs of the
guest), and it is convenient for updating the value.
To achieve this, the patch introduces a helper,
kvm_arm_pmu_get_max_counters(), that reads the maximum number of
counters from the arm_pmu associated to the VM. Make the function
global as upcoming patches will be interested to know the value
while setting the PMCR.N of the guest from userspace.
KVM does not yet support userspace modifying PMCR_EL0.N.
The following patch will add support for that.
Reviewed-by: Sebastian Ott <sebott@redhat.com>
Co-developed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
Link: https://lore.kernel.org/r/20231020214053.2144305-5-rananta@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Add a helper to read a vCPU's PMCR_EL0, and use it whenever KVM
reads a vCPU's PMCR_EL0.
Currently, the PMCR_EL0 value is tracked per vCPU. The following
patches will make (only) PMCR_EL0.N track per guest. Having the
new helper will be useful to combine the PMCR_EL0.N field
(tracked per guest) and the other fields (tracked per vCPU)
to provide the value of PMCR_EL0.
No functional change intended.
Reviewed-by: Sebastian Ott <sebott@redhat.com>
Signed-off-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20231020214053.2144305-4-rananta@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Future changes to KVM's sysreg emulation will rely on having a valid PMU
instance to determine the number of implemented counters (PMCR_EL0.N).
This is earlier than when userspace is expected to modify the vPMU
device attributes, where the default is selected today.
Select the default PMU when handling KVM_ARM_VCPU_INIT such that it is
available in time for sysreg emulation.
Reviewed-by: Sebastian Ott <sebott@redhat.com>
Co-developed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
Link: https://lore.kernel.org/r/20231020214053.2144305-3-rananta@google.com
[Oliver: rewrite changelog]
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Pull misc fixes from Andrew Morton:
"20 hotfixes. 12 are cc:stable and the remainder address post-6.5
issues or aren't considered necessary for earlier kernel versions"
* tag 'mm-hotfixes-stable-2023-10-24-09-40' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
maple_tree: add GFP_KERNEL to allocations in mas_expected_entries()
selftests/mm: include mman header to access MREMAP_DONTUNMAP identifier
mailmap: correct email aliasing for Oleksij Rempel
mailmap: map Bartosz's old address to the current one
mm/damon/sysfs: check DAMOS regions update progress from before_terminate()
MAINTAINERS: Ondrej has moved
kasan: disable kasan_non_canonical_hook() for HW tags
kasan: print the original fault addr when access invalid shadow
hugetlbfs: close race between MADV_DONTNEED and page fault
hugetlbfs: extend hugetlb_vma_lock to private VMAs
hugetlbfs: clear resv_map pointer if mmap fails
mm: zswap: fix pool refcount bug around shrink_worker()
mm/migrate: fix do_pages_move for compat pointers
riscv: fix set_huge_pte_at() for NAPOT mappings when a swap entry is set
riscv: handle VM_FAULT_[HWPOISON|HWPOISON_LARGE] faults instead of panicking
mmap: fix error paths with dup_anon_vma()
mmap: fix vma_iterator in error path of vma_merge()
mm: fix vm_brk_flags() to not bail out while holding lock
mm/mempolicy: fix set_mempolicy_home_node() previous VMA pointer
mm/page_alloc: correct start page when guard page debug is enabled
Suzuki noticed that KVM's PMU emulation is oblivious to the NSU and NSK
event filter bits. On systems that have EL3 these bits modify the
filter behavior in non-secure EL0 and EL1, respectively. Even though the
kernel doesn't use these bits, it is entirely possible some other guest
OS does. Additionally, it would appear that these and the M bit are
required by the architecture if EL3 is implemented.
Allow the EL3 event filter bits to be set if EL3 is advertised in the
guest's ID register. Implement the behavior of NSU and NSK according to
the pseudocode, and entirely ignore the M bit for perf event creation.
Reported-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20231019185618.3442949-3-oliver.upton@linux.dev
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
The NSH bit, which filters event counting at EL2, is required by the
architecture if an implementation has EL2. Even though KVM doesn't
support nested virt yet, it makes no effort to hide the existence of EL2
from the ID registers. Userspace can, however, change the value of PFR0
to hide EL2. Align KVM's sysreg emulation with the architecture and make
NSH RES0 if EL2 isn't advertised. Keep in mind the bit is ignored when
constructing the backing perf event.
While at it, build the event type mask using explicit field definitions
instead of relying on ARMV8_PMU_EVTYPE_MASK. KVM probably should've been
doing this in the first place, as it avoids changes to the
aforementioned mask affecting sysreg emulation.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20231019185618.3442949-2-oliver.upton@linux.dev
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
