Jonathan writes:
1st set of IIO new device support, features and cleanup for 5.17
Includes some fixes that were either late breaking, low priority or
complex enough to not be good to rush in late in the cycle.
Tree rebased today to fix up some trivial issues + pull in a fix that
was previously on the fixes-togreg branch. Vast majority have been
in linux-next for some time now.
New device support
* adi,ad7293
- New driver and bindings for this Power Amplifier drain current
controller. A complex device with various related monitoring functions.
* adi,ad75513R
- New driver and bindings for this combined ADC and DAC device.
- A few follow up fixes.
* adi,admv8818
- New driver (and type) for this 2-18GHz filter device. Includes
bindings and ABI documentation to allow clk_notifier based auto
adjustment of the filters in appropriate applications.
* liteon,ltr501
- Support for the ltr303. ID and chip specific info table.
* xilinx,ams
- New generic firmware function fwnode_iomap() as used in this driver.
- New driver and bindings for this ADC and on-chip sensors as found
in various Xilinx devices.
Core
* Introduced IIO_VAL_INT_64 which uses val and val2 in IIO callbacks to
form a 64 bit integer when higher precision needed.
* Allow IIO_ENUM_AVAILABLE to be used with different shared values.
* Fix a long term issue with scheduling whilst atomic when iio_trig_poll()
is called but no trigger consumers are actually enabled and hence the
trigger may be reenabled from the interrupt handler. Seen in the wild
on the tsc2046.
* Mark iio_device_type const.
* buffer: Use a separate index variable to simplify code.
* buffer-dma: Clear out unused struct iio_buffer_block
* buffer-dmaengine: Switch to cheaper round_down() as power of 2 values.
Tests/tools
* format_value
- Check against NULL returns from allocations in tests.
- Add IIO_VAL_INT_64 test case.
* event_monitor
- Flush the output after event to given more consistent latency
when tool output piped to other programs.
Driver Features
* axp20x
- Add support for NTC thermistor channel and document TS pin binding.
* arm,scmi
- Add reading of raw channel values (using IIO_VAL_INT_64)
* liteon,ltr501
- Add proximity-near-level support and dt-binding.
Tree wide cleanup
* Remove no-op trigger ops from multiple drivers.
* Stop using dev_get_drvdata() on the iio_dev->dev in various drivers
and then stop assigning it to allow this to be used for other purposes.
We can always get to the indio_dev using dev_to_iio_dev() which is
a container_of() based approach. Also cleanup up some related unnecessary
convoluted cases.
- atmel,at91-sam5d2
- nxp,imx7d
- meas,ms5611
- st,st_sensors
* Where available (or easy to introduce) use the scan_type.* values
in place of a second copy for read_raw and similar paths.
- adi,ad7266
- bosch,bma220
- fsl,mac3110
- fsl,mma7455
- fsl,mpl3115
- kionix,kcjk-1013
- sensortek,stk8ba50
- sensortek,stk8312
- ti,adc12138
- ti,ads1015
- vti,sca3000
- xilinx,xadc-core
* Switch drives over to generic firmware properties including appropriate
header changes to avoid including of.h
- Various DACs had false CONFIG_OF dependencies.
- dpot-dac
- envelope-detector
- adi,ad5755
- adi,ad5758
- capella,cm3605
- maxim,max9611
- microchip,mcp41010
- microchip,mcp3911
- ti,adc12138
* Trivial clang warning fixes for W=1 warnings.
Driver specific cleanup and minor fixes
* adi,ad7606
- Comment fixes.
* ams,ad3935
- Drop pointless cast to the same type.
* atmel,at91-sama5d2
- Fix wrong cast of iio_dev->dev to platform_device that happened to
be harmless.
* fsl,mma7660
- Stop i2c remove() function returning an error code. Part of a rework
to eventually stop returning anything from these.
* fsl,mma8452
- Use correct type for local irqreturn_t.
* nxp,imx8mq
- Maintainer email address update.
* nxp,lpc18xx_adc
- Ensure clk_prepare_enable() called before clk_get_rate().
- Switch of.h for mod_devicetable.h to reflect no of specific functions,
just the id table.
* renesas,rzg2l
- Drop a dev_err() that just duplicates error printed in platform_get_irq()
* sgx,vz89x
- Drop pointless cast.
* st,lsm6dsx
- Make it possible to disable the sensorhub from DT to avoid a corner
case where the address of a slave device many be accidentally modified.
* st,stm32-adc
- Stop leaking an of_node in an error path.
* st,stmp2
- Avoid wrong sized type for bit field which could result in
over-reading (harmless). Precursor to enabling -Warray-bounds.
* ti,adc081c
- Put back some ACPI support for non standards compliant ADC081C
ID because it is known to be in the wild on some Aaeon boards.
* ti,ads8688
- Cleanup redundant local ret variable assignment.
* ti,ina2xx-adc
- Use helper macro kthread_run() to replace some boilerplate.
- Avoid double reference counting.
- Drop pointless cast.
* xilinx,xadc
- Make the IRQ optional as not always wired to the host system.
* tag 'iio-for-5.17a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (103 commits)
iio: adc: ti-adc081c: Partial revert of removal of ACPI IDs
iio:addac:ad74413r: Fix uninitialized ret in a path that won't be hit.
MAINTAINERS: Add maintainer for xilinx-ams
dt-bindings: iio: adc: Add Xilinx AMS binding documentation
iio: adc: Add Xilinx AMS driver
device property: Add fwnode_iomap()
iio:accel:kxcjk-1013: Mark struct __maybe_unused to avoid warning.
iio:accel:bmc150: Mark structure __maybe_unused as only needed with for pm ops.
iio:dummy: Drop set but unused variable len.
iio:magn:ak8975: Suppress clang W=1 warning about pointer to enum conversion.
iio:imu:inv_mpu6050: Suppress clang W=1 warning about pointer to enum conversion.
iio:imu:inv_icm42600: Suppress clang W=1 warning about pointer to enum conversion.
iio:dac:mcp4725: Suppress clang W=1 warning about pointer to enum conversion.
iio:amplifiers:hmc425a: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:ti-ads1015: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:rcar: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:ina2xx-adc: Suppress clang W=1 warning about pointer to enum conversion.
iio:accel:bma180: Suppress clang W=1 warning about pointer to enum conversion.
drivers:iio:dac: Add AD3552R driver support
dt-bindings: iio: dac: Add adi,ad3552r.yaml
...
Probably a cut and paste error, but the binding header used in the
example is for the wrong device and nothing from it is used.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Reviewed-by: Rob Herring <robh@kernel.org>
The AD74412R and AD74413R are quad-channel, software configurable,
input/output solutions for building and process control applications.
They contain functionality for analog output, analog input, digital input,
resistance temperature detector, and thermocouple measurements integrated
into a single chip solution with an SPI interface.
The devices feature a 16-bit ADC and four configurable 13-bit DACs to
provide four configurable input/output channels and a suite of diagnostic
functions.
The AD74413R differentiates itself from the AD74412R by being
HART-compatible.
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211205114045.173612-3-cosmin.tanislav@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull MFD updates from Lee Jones:
"Removed Drivers:
- Remove support for TI TPS80031/TPS80032 PMICs
New Device Support:
- Add support for Magnetic Reader to TI AM335x
- Add support for DA9063_EA to Dialog DA9063
- Add support for SC2730 PMIC to Spreadtrum SC27xx
- Add support for MacBookPro16,2 ICL-N UART Intel LPSS PCI
- Add support for lots of new PMICS in QCom SPMI PMIC
- Add support for ADC to Diolan DLN2
New Functionality:
- Add support for Power Off to Rockchip RK817
Fix-ups:
- Simplify Regmap passing to child devices in hi6421-spmi-pmic
- SPDX licensing updates in ti_am335x_tscadc
- Improve error handling in ti_am335x_tscadc
- Expedite clock search in ti_am335x_tscadc
- Generic simplifications in ti_am335x_tscadc
- Use generic macros/defines in ti_am335x_tscadc
- Remove unused code in ti_am335x_tscadc, cros_ec_dev
- Convert to GPIOD in wcd934x
- Add namespacing in ti_am335x_tscadc
- Restrict compilation to relevant arches in intel_pmt
- Provide better description/documentation in exynos_lpass
- Add SPI device ID table in altera-a10sr, motorola-cpcap,
sprd-sc27xx-spi
- Change IRQ handling in qcom-pm8xxx
- Split out I2C and SPI code in arizona
- Explicitly include used headers in altera-a10sr
- Convert sysfs show() function to in sysfs_emit
- Standardise *_exit() and *_remove() return values in mc13xxx,
stmpe, tps65912
- Trivial (style/spelling/whitespace) fixups in ti_am335x_tscadc,
qcom-spmi-pmic, max77686-private
- Device Tree fix-ups in ti,am3359-tscadc, samsung,s2mps11,
samsung,s2mpa01, samsung,s5m8767, brcm,misc, brcm,cru, syscon,
qcom,tcsr, xylon,logicvc, max77686, x-powers,ac100,
x-powers,axp152, x-powers,axp209-gpio, syscon, qcom,spmi-pmic
Bug Fixes:
- Balance refcounting (get/put) in ti_am335x_tscadc, mfd-core
- Fix IRQ trigger type in sec-irq, max77693, max14577
- Repair off-by-one in altera-sysmgr
- Add explicit 'select MFD_CORE' to MFD_SIMPLE_MFD_I2C"
* tag 'mfd-next-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (95 commits)
mfd: simple-mfd-i2c: Select MFD_CORE to fix build error
mfd: tps80031: Remove driver
mfd: max77686: Correct tab-based alignment of register addresses
mfd: wcd934x: Replace legacy gpio interface for gpiod
dt-bindings: mfd: qcom: pm8xxx: Add pm8018 compatible
mfd: dln2: Add cell for initializing DLN2 ADC
mfd: qcom-spmi-pmic: Add missing PMICs supported by socinfo
mfd: qcom-spmi-pmic: Document ten more PMICs in the binding
mfd: qcom-spmi-pmic: Sort compatibles in the driver
mfd: qcom-spmi-pmic: Sort the compatibles in the binding
mfd: janz-cmoio: Replace snprintf in show functions with sysfs_emit
mfd: altera-a10sr: Include linux/module.h
mfd: tps65912: Make tps65912_device_exit() return void
mfd: stmpe: Make stmpe_remove() return void
mfd: mc13xxx: Make mc13xxx_common_exit() return void
dt-bindings: mfd: syscon: Add samsung,exynosautov9-sysreg compatible
mfd: altera-sysmgr: Fix a mistake caused by resource_size conversion
dt-bindings: gpio: Convert X-Powers AXP209 GPIO binding to a schema
dt-bindings: mfd: syscon: Add rk3368 QoS register compatible
mfd: arizona: Split of_match table into I2C and SPI versions
...
Jonathan writes:
2nd set of IIO new driver, cleanups and features for the 5.16 cycle
New device support
* adrf6780 microwave upconverter.
- New driver for this interesting device including bindings.
Features
* lite-on ltr501
- Add dt-bindings including vendor ID and of_device_id table.
- Add regulator support.
* sensiron,scd4x
- Add reporting of channel scale.
Cleanups including fixes for things in this cycle
* Tree wide: Another set of dev_err_probe() introductions to reduce
noise in logs when deferred probing is needed and provide more debug
info. Devices included this time:
- amlogic,meson_saradc
- capella,cm3605
- fsl,imx7d
- maxim,max1118
- maxim,max1241
- nxp,lpc18xx
- qcom,pm8xxxx-xoadc
- rockchip,saradc
- sharp,gp2ap002
- sterricson,ab8500
- ti,ads7950
* core - iio:buffer
- Fix a path where a ret value is not intialized.
* channel-mux
- Add support to mux core subsystem for a settling delay and use
it in the iio-channel-mux driver.
- Fix a few dt binding warnings.
* nxp,lpc18xx
- Convert to devm_ functions for all of probe and drop remove()
* st,lsm6dsx
- Suppress a warning due to lack of handling of an enum *_MAX entry
that is just there to get the size.
* st,stm32-adc
- Add generic channel binding, deprecating the old approach.
- Add nvmem support to get calibration data for the vrefint channel and
use it to perform such calibration.
- Add a binding for sample-time to the generic channel description as it
can be per channel.
* ti,adc128s052
- Use devm_ managed functions and drop remove()
* vti,sca3000
- Use sign_extend32() rather than opencoding.
* xilinx,xadc
- Drop irq field from state structure as now just used in probe.
* tag 'iio-for-5.16b' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (36 commits)
dt-bindings: iio: frequency: add adrf6780 doc
iio: frequency: adrf6780: add support for ADRF6780
iio: chemical: scd4x: Add a scale for the co2 concentration reading
dt-bindings: iio: io-channel-mux: allow duplicate channel, labels
dt-bindings: iio: io-channel-mux: add optional #io-channel-cells
iio: adc: adc128s052: Simplify adc128_probe()
iio: multiplexer: iio-mux: Support settle-time-us property
dt-bindings: iio: io-channel-mux: Add property for settle time
mux: add support for delay after muxing
iio: adc: stm32-adc: use generic binding for sample-time
iio: adc: stm32-adc: add vrefint calibration support
iio: adc: stm32-adc: add support of internal channels
iio: adc: stm32-adc: add support of generic channels binding
iio: adc: stm32-adc: split channel init into several routines
dt-bindings: iio: stm32-adc: add nvmem support for vrefint internal channel
dt-bindings: iio: stm32-adc: add generic channel binding
iio: accel: sca3000: Use sign_extend32() instead of opencoding sign extension.
iio: xilinx-xadc: Remove `irq` field from state struct
iio: imu: st_lsm6dsx: Avoid potential array overflow in st_lsm6dsx_set_odr()
iio: light: gp2ap002: Make use of the helper function dev_err_probe()
...
Jonathan writes:
First set of IIO fixes for the 5.16 cycle
As these are very late in the 5.15 cycle and non are particularly urgent,
they can wait for the merge window.
Key element in this set is Yang Yingliang has identified a number of
issues in error paths introduced recently when we added multiple
buffer support.
Other fixes:
* adi,ad5662
- Fix handling of i2c_master_send() return value.
* adi,ad5766
- Fix a wrong dt-property name that indicated wrong units and
did not mach the bindings.
- Associated 'fix' of the bindings example to have a possible scale.
* st,pressure-spi
- Add some missing entries to the spi_device_id table to ensure
auto-loading works.
* ti,tsc2046
- Fix a backwards comparison leading to a false dev_warn
* tag 'iio-fixes-for-5.16a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: buffer: Fix memory leak in iio_buffers_alloc_sysfs_and_mask()
iio: adc: tsc2046: fix scan interval warning
iio: core: fix double free in iio_device_unregister_sysfs()
iio: core: check return value when calling dev_set_name()
iio: buffer: Fix memory leak in iio_buffer_register_legacy_sysfs_groups()
iio: buffer: Fix double-free in iio_buffers_alloc_sysfs_and_mask()
iio: buffer: Fix memory leak in __iio_buffer_alloc_sysfs_and_mask()
iio: buffer: check return value of kstrdup_const()
iio: dac: ad5446: Fix ad5622_write() return value
Documentation:devicetree:bindings:iio:dac: Fix val
drivers: iio: dac: ad5766: Fix dt property name
iio: st_pressure_spi: Add missing entries SPI to device ID table
This is needed since an empty channel label is used to indicate an
unused channel, and there can be more that one of those.
Fixes the following problem reported by dtbs_check:
envelope-detector-mux: channels: ['', '', 'sync-1', 'in', 'out', 'sync-2', 'sys-reg', 'ana-reg'] has non-unique elements
arch/arm/boot/dts/at91-tse850-3.dt.yaml
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Needed for in-kernel use of the child channels of the mux.
Fixes problems like this, reported by dtbs_check:
adc0mux: '#io-channel-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dt.yaml
Suggested-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jonathan writes:
2nd set of new IIO device support and cleanups for the 5.15 cycle.
A small pull request to pick up a few new drivers and some cleanup
and fix patches.
New device support
* ad5110 non-volatile digital potentiometer
- New driver
* renesas rzl/gl2 12-bit / 8 channel ADC block
- New driver and bindings
Minor or late breaking fixes and cleanups
* ltc2983
- Fix a false assumption of initial interrupt during probe().
* hp03
- Use devm_* to simplify probe and allow the remove function to be dropped.
* rockchip_saradc
- Use a regulator notifier to reduce overheads of querying the scale.
* tag 'iio-for-5.15b' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: Add driver for Renesas RZ/G2L A/D converter
dt-bindings: iio: adc: Add binding documentation for Renesas RZ/G2L A/D converter
iio: pressure: hp03: update device probe to register with devm functions
iio: adc: rockchip_saradc: add voltage notifier so get referenced voltage once at probe
iio: ltc2983: fix device probe
iio: potentiometer: Add driver support for AD5110
dt-bindings: iio: potentiometer: Add AD5110 in trivial-devices
BMC156 is very smilar to BMC150, but it has only one accelerometer
interrupt pin. It would make sense if only INT1 was exposed but someone
at Bosch decided to only have an INT2 pin.
In this case, it does not make sense if the first interrupt pin is
treated as INT1 (since that pin does not exist). Add a note to the
bindings that the first interrupt pin is treated as INT2 for BMC156.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210802155657.102766-3-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The original bindings was listing the length of the interrupts as either
1 or 2, depending on the setup. This is also what is enforced by the top
level schema.
However, that is further constrained with an if clause that require
exactly two interrupts, even though it might not make sense on those
devices or in some setups.
Let's remove the clause entirely.
Cc: Denis Ciocca <denis.ciocca@st.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Fixes: 0cd7114580 ("iio: st-sensors: Update ST Sensor bindings")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210721140424.725744-16-maxime@cerno.tech
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In Linux the bma180 and bmc150-accel driver cover fairly similar chips
from Bosch (just with minor register differences). For the DT schema,
this does not make any difference: They both represent I2C/SPI devices,
have one or two interrupts plus a vdd/vddio-supply.
This means there is no need to duplicate the schema, we can just
document the compatibles for both drivers in a single DT schema.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210614163150.7774-4-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Bosch accelerometers similar to BMA255 are initially configured to
emit an active-high interrupt signal. This is currently not re-configured
in the bmc150-accel driver so the interrupt should most certainly be
IRQ_TYPE_EDGE_RISING (or potentially IRQ_TYPE_LEVEL_HIGH).
(Unless there is some kind of inverter installed on the board...)
At the moment the bmc150-accel driver forcefully requests the IRQ
using IRQF_TRIGGER_RISING, which means that the IRQ type is currently
ignored in all existing device trees.
Fixes: 6259551cf1 ("iio: accel: bmc150-accel: Add DT bindings")
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210614163150.7774-2-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
