Pull devicetree fixes from Rob Herring:
- Two fixes due to DT node name changes on Arm, Ltd. boards
- Treewide rename of Ingenic CGU headers
- Update ST email addresses
- Remove Netlogic DT bindings
- Dropping few more cases of redundant 'maxItems' in schemas
- Convert toshiba,tc358767 bridge binding to schema
* tag 'devicetree-fixes-for-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: watchdog: sunxi: fix error in schema
bindings: media: venus: Drop redundant maxItems for power-domain-names
dt-bindings: Remove Netlogic bindings
clk: versatile: clk-icst: Ensure clock names are unique
of: Support using 'mask' in making device bus id
dt-bindings: treewide: Update @st.com email address to @foss.st.com
dt-bindings: media: Update maintainers for st,stm32-hwspinlock.yaml
dt-bindings: media: Update maintainers for st,stm32-cec.yaml
dt-bindings: mfd: timers: Update maintainers for st,stm32-timers
dt-bindings: timer: Update maintainers for st,stm32-timer
dt-bindings: i2c: imx: hardware do not restrict clock-frequency to only 100 and 400 kHz
dt-bindings: display: bridge: Convert toshiba,tc358767.txt to yaml
dt-bindings: Rename Ingenic CGU headers to ingenic,*.h
Both hardware and driver can communicate DDC over i2c bus.
Fixes warnings as:
arch/arm/boot/dts/tegra20-paz00.dt.yaml: panel: 'ddc-i2c-bus' does not match any of the regexes: 'pinctrl-[0-9]+'
From schema: /home/runner/work/linux/linux/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
Signed-off-by: David Heidelberg <david@ixit.cz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210927214503.36012-1-david@ixit.cz
This tablet display is unique and hence must be added to documentation.
Unfortunately, it's real make and number is not known due to obscure and
missing documentation and lack of writing on the display assembly
itself.
So the natural alternative that came to mind is to name the panel after
the device that contained it (an Android tablet). Hopefully that isn't
an issue.
I can confirm that the parameters that I've obtained are correct since
they came from a dump of the original Android OS.
Signed-off-by: Nikola Pavlica <pavlica.nikola@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211002202905.509437-2-pavlica.nikola@gmail.com
eDP panels generally contain almost everything needed to control them
in their EDID. This comes from their DP heritage were a computer needs
to be able to properly control pretty much any DP display that's
plugged into it.
The one big issue with eDP panels and the reason that we need a panel
driver for them is that the power sequencing can be different per
panel.
While it is true that eDP panel sequencing can be arbitrarily complex,
in practice it turns out that many eDP panels are compatible with just
some slightly different delays. See the contents of the bindings file
introduced in this patch for some details.
The fact that eDP panels are 99% probable and that the power
sequencing (especially power up) can be compatible between many panels
means that there's a constant desire to plug multiple different panels
into the same board. This could be for second sourcing purposes or to
support multiple SKUs (maybe a 11" and a 13", for instance).
As discussed [1], it should be OK to support this by adding two
properties to the device tree to specify the delays needed for
powering up the panel the first time. We'll create a new "edp-panel"
bindings file and define the two delays that might need to be
specified. NOTE: in the vast majority of the cases (HPD is hooked up
and isn't glitchy or is debounced) even these delays aren't needed.
[1] https://lore.kernel.org/r/CAD=FV=VZYOMPwQZzWdhJGh5cjJWw_EcM-wQVEivZ-bdGXjPrEQ@mail.gmail.com
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.1.I1116e79d34035338a45c1fc7cdd14a097909c8e0@changeid
Required bump from v5.13-rc3 to v5.14-rc3, and to pick up sysfb compilation fixes.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
drm-misc-next for v5.15-rc1:
UAPI Changes:
- Remove sysfs stats for dma-buf attachments, as it causes a performance regression.
Previous merge is not in a rc kernel yet, so no userspace regression possible.
Cross-subsystem Changes:
- Sanitize user input in kyro's viewport ioctl.
- Use refcount_t in fb_info->count
- Assorted fixes to dma-buf.
- Extend x86 efifb handling to all archs.
- Fix neofb divide by 0.
- Document corpro,gm7123 bridge dt bindings.
Core Changes:
- Slightly rework drm master handling.
- Cleanup vgaarb handling.
- Assorted fixes.
Driver Changes:
- Add support for ws2401 panel.
- Assorted fixes to stm, ast, bochs.
- Demidlayer ingenic irq.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2d0d2fe8-01fc-e216-c3fd-38db9e69944e@linux.intel.com
drm-misc-next for v5.15:
UAPI Changes:
Cross-subsystem Changes:
- udmabuf: Add support for mapping hugepages
- Add dma-buf stats to sysfs.
- Assorted fixes to fbdev/omap2.
- dma-buf: Document DMA_BUF_IOCTL_SYNC
- Improve dma-buf non-dynamic exporter expectations better.
- Add module parameters for dma-buf size and list limit.
- Add HDMI codec support to vc4, to replace vc4's own codec.
- Document dma-buf implicit fencing rules.
- dma_resv_test_signaled test_all handling.
Core Changes:
- Extract i915's eDP backlight code into DRM helpers.
- Assorted docbook updates.
- Rework drm_dp_aux documentation.
- Add support for the DP aux bus.
- Shrink dma-fence-chain slightly.
- Add alloc/free helpers for dma-fence-chain.
- Assorted fixes to TTM., drm/of, bridge
- drm_gem_plane_helper_prepare/cleanup_fb is now the default for gem drivers.
- Small fix for scheduler completion.
- Remove use of drm_device.irq_enabled.
- Print the driver name to dmesg when registering framebuffer.
- Export drm/gem's shadow plane handling, and use it in vkms.
- Assorted small fixes.
Driver Changes:
- Add eDP backlight to nouveau.
- Assorted fixes and cleanups to nouveau, panfrost, vmwgfx, anx7625,
amdgpu, gma500, radeon, mgag200, vgem, vc4, vkms, omapdrm.
- Add support for Samsung DB7430, Samsung ATNA33XC20, EDT ETMV570G2DHU,
EDT ETM0350G0DH6, Innolux EJ030NA panels.
- Fix some simple pannels missing bus_format and connector types.
- Add mks-guest-stats instrumentation support to vmwgfx.
- Merge i915-ttm topic branch.
- Make s6e63m0 panel use Mipi-DBI helpers.
- Add detect() supoprt for AST.
- Use interrupts for hotplug on vc4.
- vmwgfx is now moved to drm-misc-next, as sroland is no longer a maintainer for now.
- vmwgfx now uses copies of vmware's internal device headers.
- Slowly convert ti-sn65dsi83 over to atomic.
- Rework amdgpu dma-resv handling.
- Fix virtio fencing for planes.
- Ensure amdgpu can always evict to SYSTEM.
- Many drivers fixed for implicit fencing rules.
- Set default prepare/cleanup fb for tiny, vram and simple helpers too.
- Rework panfrost gpu reset and related serialization.
- Update VKMS todo list.
- Make bochs a tiny gpu driver, and use vram helper.
- Use linux irq interfaces instead of drm_irq in some drivers.
- Add support for Raspberry Pi Pico to GUD.
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Fri 16 Jul 2021 21:06:04 AEST
# gpg: using RSA key B97BD6A80CAC4981091AE547FE558C72A67013C3
# gpg: Good signature from "Maarten Lankhorst <maarten.lankhorst@linux.intel.com>" [expired]
# gpg: aka "Maarten Lankhorst <maarten@debian.org>" [expired]
# gpg: aka "Maarten Lankhorst <maarten.lankhorst@canonical.com>" [expired]
# gpg: Note: This key has expired!
# Primary key fingerprint: B97B D6A8 0CAC 4981 091A E547 FE55 8C72 A670 13C3
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/444811c3-cbec-e9d5-9a6b-9632eda7962a@linux.intel.com
Pull devicetree updates from Rob Herring:
- Refine reserved memory nomap handling
- Merge some PCI and non-PCI address handling implementations
- Simplify of_address.h header ifdefs
- Improve printk handling of some 64-bit types
- Convert adi,adv7511, Arm ccree, Arm SCMI, Arm SCU, Arm TWD timer, Arm
VIC, arm,sbsa-gwdt, Arm/Amlogic SCPI, Aspeed I2C, Broadcom iProc PWM,
linaro,optee-tz, MDIO GPIO, Mediatek RNG, MTD physmap, NXP
pcf8563/pcf85263/pcf85363, Renesas TPU, renesas,emev2-smu,
renesas,r9a06g032-sysctrl, sysc-rmobile, Tegra20 EMC, TI AM56 PCI, TI
OMAP mailbox, TI SCI bindings, virtio-mmio, Zynq FPGA, and ZynqMP RTC
to DT schema
- Convert mux and mux controller bindings to schema. This includes MDIO
IIO, and I2C muxes.
- Add Arm PL031 RTC binding schema
- Add vendor prefixes for StarFive Technology Co. Ltd. and Insignal Ltd
- Fix some stale doc references
- Remove stale property-units.txt. Superseded by schema in dt-schema
repo.
- Fixes for 'unevaluatedProperties' handling (enabled with experimental
json-schema support)
- Drop redundant usage of minItems and maxItems across the tree
- Update some examples to use bindings with a schema
* tag 'devicetree-for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (83 commits)
dt-bindings: Fix 'unevaluatedProperties' errors in DT graph users
dt-bindings: display: renesas,du: Fix 'ports' reference
dt-bindings: media: adv7180: Add missing video-interfaces.yaml reference
dt-bindings: crypto: ccree: Convert to json-schema
dt-bindings: fpga: zynq: convert bindings to YAML
dt-bindings: rtc: zynqmp: convert bindings to YAML
dt-bindings: interrupt-controller: Convert ARM VIC to json-schema
of: of_reserved_mem: mark nomap memory instead of removing
of: of_reserved_mem: only call memblock_free for normal reserved memory
dt-bindings: Drop redundant minItems/maxItems
dt-bindings: spmi: Correct 'reg' schema
of: reserved-memory: Add stub for RESERVEDMEM_OF_DECLARE()
dt-bindings: clk: vc5: Fix example
dt-bindings: timer: renesas,tmu: add r8a779a0 TMU support
dt-bindings: drm: bridge: adi,adv7511.txt: convert to yaml
dt-bindings: PCI: ti,am65: Convert PCIe host/endpoint mode dt-bindings to YAML
of: Remove superfluous casts when printing u64 values
of: Fix truncation of memory sizes on 32-bit platforms
dt-bindings: rtc: nxp,pcf8563: Absorb pcf85263/pcf85363 bindings
dt-bindings: pwm: Use examples with documented/matching schema
...
The HPD (Hot Plug Detect) signal is present in many (probably even
"most") eDP panels. For eDP, this signal isn't actually used for
detecting hot-plugs of the panel but is more akin to a "panel ready"
signal. After you provide power to the panel, panel timing diagrams
typically say that you should wait for HPD to be asserted (or wait a
fixed amount of time) before talking to the panel.
The panel-simple bindings describes many eDP panels and many of these
panels provide the HPD signal. We should add the HPD-related
properties to the panel-simple bindings. The HPD properties are
actually defined in panel-common.yaml, so adding them here just
documents that they are OK for panels handled by the panel-simple
bindings.
NOTE: whether or not we'd include HPD properties in the panel node is
more a property of the board design than the panel itself. For most
boards using these eDP panels everything "magically" works without
specifying any HPD properties and that's been why we haven't needed to
allow the HPD properties earlier. On these boards the HPD signal goes
directly to a dedicated "HPD" input to the eDP controller and this
connection doesn't need to be described in the device tree. The only
time the HPD properties are needed in the device tree are if HPD is
hooked up to a GPIO or if HPD is normally on the panel but isn't used
on a given board. That means that if we don't allow the HPD properties
in panel-simple then one could argue that we've got to boot all eDP
panels (or at least all those that someone could conceivably put on a
system where HPD goes to a GPIO or isn't hooked up) from panel-simple.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210611101711.v10.1.Ieb731d23680db4700cc41fe51ccc73ba0b785fb7@changeid
Pull MIPS updates from Thomas Bogendoerfer:
- removed get_fs/set_fs
- removed broken/unmaintained MIPS KVM trap and emulate support
- added support for Loongson-2K1000
- fixes and cleanups
* tag 'mips_5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (107 commits)
MIPS: BCM63XX: Use BUG_ON instead of condition followed by BUG.
MIPS: select ARCH_KEEP_MEMBLOCK unconditionally
mips: Do not include hi and lo in clobber list for R6
MIPS:DTS:Correct the license for Loongson-2K
MIPS:DTS:Fix label name and interrupt number of ohci for Loongson-2K
MIPS: Avoid handcoded DIVU in `__div64_32' altogether
lib/math/test_div64: Correct the spelling of "dividend"
lib/math/test_div64: Fix error message formatting
mips/bootinfo:correct some comments of fw_arg
MIPS: Avoid DIVU in `__div64_32' is result would be zero
MIPS: Reinstate platform `__div64_32' handler
div64: Correct inline documentation for `do_div'
lib/math: Add a `do_div' test module
MIPS: Makefile: Replace -pg with CC_FLAGS_FTRACE
MIPS: pci-legacy: revert "use generic pci_enable_resources"
MIPS: Loongson64: Add kexec/kdump support
MIPS: pci-legacy: use generic pci_enable_resources
MIPS: pci-legacy: remove busn_resource field
MIPS: pci-legacy: remove redundant info messages
MIPS: pci-legacy: stop using of_pci_range_to_resource
...
Pull devicetree updates from Rob Herring:
- Refactor powerpc and arm64 kexec DT handling to common code. This
enables IMA on arm64.
- Add kbuild support for applying DT overlays at build time. The first
user are the DT unittests.
- Fix kerneldoc formatting and W=1 warnings in drivers/of/
- Fix handling 64-bit flag on PCI resources
- Bump dtschema version required to v2021.2.1
- Enable undocumented compatible checks for dtbs_check. This allows
tracking of missing binding schemas.
- DT docs improvements. Regroup the DT docs and add the example schema
and DT kernel ABI docs to the doc build.
- Convert Broadcom Bluetooth and video-mux bindings to schema
- Add QCom sm8250 Venus video codec binding schema
- Add vendor prefixes for AESOP, YIC System Co., Ltd, and Siliconfile
Technologies Inc.
- Cleanup of DT schema type references on common properties and
standard unit properties
* tag 'devicetree-for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (64 commits)
powerpc: If kexec_build_elf_info() fails return immediately from elf64_load()
powerpc: Free fdt on error in elf64_load()
of: overlay: Fix kerneldoc warning in of_overlay_remove()
of: linux/of.h: fix kernel-doc warnings
of/pci: Add IORESOURCE_MEM_64 to resource flags for 64-bit memory addresses
dt-bindings: bcm4329-fmac: add optional brcm,ccode-map
docs: dt: update writing-schema.rst references
dt-bindings: media: venus: Add sm8250 dt schema
of: base: Fix spelling issue with function param 'prop'
docs: dt: Add DT API documentation
of: Add missing 'Return' section in kerneldoc comments
of: Fix kerneldoc output formatting
docs: dt: Group DT docs into relevant sub-sections
docs: dt: Make 'Devicetree' wording more consistent
docs: dt: writing-schema: Include the example schema in the doc build
docs: dt: writing-schema: Remove spurious indentation
dt-bindings: Fix reference in submitting-patches.rst to the DT ABI doc
dt-bindings: ddr: Add optional manufacturer and revision ID to LPDDR3
dt-bindings: media: video-interfaces: Drop the example
devicetree: bindings: clock: Minor typo fix in the file armada3700-tbg-clock.txt
...
Noralf needs some patches in 5.12-rc3, and we've been delaying the 5.12
merge due to the swap issue so it looks like a good time.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The NT39016 panel is a fun beast, even though the documentation states
that the CS line is active-low, it will work just fine if the CS line is
configured as active-high, but it won't work if the CS line is forced
low or forced high.
Since it did actually work with the spi-cs-high property, this is not a
bugfix, but we should nonetheless remove that property from the example
to match the documentation.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Pull devicetree updates from Rob Herring:
- Sync dtc to upstream version v1.6.0-51-g183df9e9c2b9 and build host
fdtoverlay
- Add kbuild support to build DT overlays (%.dtbo)
- Drop NULLifying match table in of_match_device().
In preparation for this, there are several driver cleanups to use
(of_)?device_get_match_data().
- Drop pointless wrappers from DT struct device API
- Convert USB binding schemas to use graph schema and remove old plain
text graph binding doc
- Convert spi-nor and v3d GPU bindings to DT schema
- Tree wide schema fixes for if/then schemas, array size constraints,
and undocumented compatible strings in examples
- Handle 'no-map' correctly for already reserved memblock regions
* tag 'devicetree-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
driver core: platform: Drop of_device_node_put() wrapper
of: Remove of_dev_{get,put}()
dt-bindings: usb: Change descibe to describe in usbmisc-imx.txt
dt-bindings: can: rcar_canfd: Group tuples in pin control properties
dt-bindings: power: renesas,apmu: Group tuples in cpus properties
dt-bindings: mtd: spi-nor: Convert to DT schema format
dt-bindings: Use portable sort for version cmp
dt-bindings: ethernet-controller: fix fixed-link specification
dt-bindings: irqchip: Add node name to PRUSS INTC
dt-bindings: interconnect: Fix the expected number of cells
dt-bindings: Fix errors in 'if' schemas
dt-bindings: iommu: renesas,ipmmu-vmsa: Make 'power-domains' conditionally required
dt-bindings: Fix undocumented compatible strings in examples
kbuild: Add support to build overlays (%.dtbo)
scripts: dtc: Remove the unused fdtdump.c file
scripts: dtc: Build fdtoverlay tool
scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9
scripts: dtc: Fetch fdtoverlay.c from external DTC project
dt-bindings: thermal: sun8i: Fix misplaced schema keyword in compatible strings
dt-bindings: iio: dac: Fix AD5686 references
...
This fixes the following problems with the s6e63m0 display
bindings:
- When used on the DSI bus, the panel is listed directly as
a subnode on the DSI host so the "port" node is not
compulsory. Remove "port" from required properties.
- The panel contains its own backlight control, so reference
the backlight common properties and list default-brightness
and max-brightness as supported but optional properties.
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210101114522.1981838-1-linus.walleij@linaro.org
drm-misc-next for v5.12:
UAPI Changes:
- Not necessarily one, but we document that userspace needs to force probe connectors.
Cross-subsystem Changes:
- Require FB_ATY_CT for aty on sparc64.
- video: Fix documentation, and a few compiler warnings.
- Add devicetree bindings for DP connectors.
- dma-buf: Update kernel-doc, and add might_lock for resv objects in begin/end_cpu_access.
Core Changes:
- ttm: Warn when releasing a pinned bo.
- ttm: Cleanup bo size handling.
- cma-helper: Remove prime infix, and implement mmap as GEM CMA functions.
- Split drm_prime_sg_to_page_addr_arrays into 2 functions.
- Add a new api to install irq using devm.
- Update panel kerneldoc to inline style.
- Add DP support to drm/bridge.
- Assorted small fixes to ttm, fb-helper, scheduler.
- Add atomic_commit_setup function callback.
- Automatically use the atomic gamma_set, instead of forcing drivers to declare the default atomic version.
- Allow using degamma for legacy gamma if gamma is not available.
- Clarify that primary/cursor planes are not tied to 1 crtc (depending on possible_crtcs).
- ttm: Cleanup the lru handler.
Driver Changes:
- Add pm support to ingenic.
- Assorted small fixes in radeon, via, rockchip, omap2fb, kmb, gma500, nouveau, virtio, hisilicon, ingenic, s6e63m0 panel, ast, udlfb.
- Add BOE NV110WTM-N61, ys57pss36bh5gq, Khadas TS050 panels.
- Stop using pages with drm_prime_sg_to_page_addr_arrays, and switch all callers to use ttm_sg_tt_init.
- Cleanup compiler and docbook warnings in a lot of fbdev devices.
- Use the drmm_vram_helper in hisilicon.
- Add support for BCM2711 DSI1 in vc4.
- Add support for 8-bit delta RGB panels to ingenic.
- Add documentation on how to test vkms.
- Convert vc4 to atomic helpers.
- Use degamma instead of gamma table in omap, to add support for CTM and color encoding/range properties.
- Rework omap DSI code, and merge all omapdrm modules now that the last omap panel is now a drm panel.
- More refactoring of omap dsi code.
- Enable 10/12 bpc outputs in vc4.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/78381a4f-45fd-aed4-174a-94ba051edd37@linux.intel.com
So far, this panel seems to be compatible with "lg,lb070wv8", on other
hand it is better to set this compatible in the devicetree. So, let's
add it for now only to the dt-binding documentation to fix the
checkpatch warnings.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some EDT compatibles are already supported by the driver but will fail
on checkpatch script. Fix it by syncing dt-bindings documentation with the
driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
