Convert phy drivers to report the link partner advertised modes using
a linkmode bitmap. This allows them to report the higher speeds which
don't fit in a u32.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both states aren't used. Most likely they result from an idea that
never materialized. So remove them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently drivers can register to receive TC block bind/unbind callbacks
by implementing the setup_tc ndo in any of their given netdevs. However,
drivers may also be interested in binds to higher level devices (e.g.
tunnel drivers) to potentially offload filters applied to them.
Introduce indirect block devs which allows drivers to register callbacks
for block binds on other devices. The callback is triggered when the
device is bound to a block, allowing the driver to register for rules
applied to that block using already available functions.
Freeing an indirect block callback will trigger an unbind event (if
necessary) to direct the driver to remove any offloaded rules and unreg
any block rule callbacks. It is the responsibility of the implementing
driver to clean any registered indirect block callbacks before exiting,
if the block it still active at such a time.
Allow registering an indirect block dev callback for a device that is
already bound to a block. In this case (if it is an ingress block),
register and also trigger the callback meaning that any already installed
rules can be replayed to the calling driver.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add macros for PHYID matching to be used in PHY driver configs.
By using these macros some boilerplate code can be avoided.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using phy_mac_interrupt() the irq number is set to
PHY_IGNORE_INTERRUPT, therefore phy_interrupt_is_valid() returns false.
As a result phy_change() effectively just calls phy_trigger_machine()
when called from phy_mac_interrupt() via phy_change_work(). So we can
call phy_trigger_machine() from phy_mac_interrupt() directly and
remove some now unneeded code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
State PHY_CHANGELINK isn't needed here, we can call the state machine
directly. We just have to remove the check for phy_polling_mode() to
make this work also in interrupt mode. Removing this check doesn't
cause any overhead because when not polling the state machine is
called only if required by some event.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that flag PHY_HAS_INTERRUPT has been replaced with a check for
callbacks config_intr and ack_interrupt, we can remove setting this
flag from all driver configs.
Last but not least remove flag PHY_HAS_INTERRUPT completely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we now have no users of sa11x0_dma_filter_fn() in the tree, we can
unexport this function, and remove the now unused header file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently BPF verifier allows narrow loads for a context field only with
offset zero. E.g. if there is a __u32 field then only the following
loads are permitted:
* off=0, size=1 (narrow);
* off=0, size=2 (narrow);
* off=0, size=4 (full).
On the other hand LLVM can generate a load with offset different than
zero that make sense from program logic point of view, but verifier
doesn't accept it.
E.g. tools/testing/selftests/bpf/sendmsg4_prog.c has code:
#define DST_IP4 0xC0A801FEU /* 192.168.1.254 */
...
if ((ctx->user_ip4 >> 24) == (bpf_htonl(DST_IP4) >> 24) &&
where ctx is struct bpf_sock_addr.
Some versions of LLVM can produce the following byte code for it:
8: 71 12 07 00 00 00 00 00 r2 = *(u8 *)(r1 + 7)
9: 67 02 00 00 18 00 00 00 r2 <<= 24
10: 18 03 00 00 00 00 00 fe 00 00 00 00 00 00 00 00 r3 = 4261412864 ll
12: 5d 32 07 00 00 00 00 00 if r2 != r3 goto +7 <LBB0_6>
where `*(u8 *)(r1 + 7)` means narrow load for ctx->user_ip4 with size=1
and offset=3 (7 - sizeof(ctx->user_family) = 3). This load is currently
rejected by verifier.
Verifier code that rejects such loads is in bpf_ctx_narrow_access_ok()
what means any is_valid_access implementation, that uses the function,
works this way, e.g. bpf_skb_is_valid_access() for __sk_buff or
sock_addr_is_valid_access() for bpf_sock_addr.
The patch makes such loads supported. Offset can be in [0; size_default)
but has to be multiple of load size. E.g. for __u32 field the following
loads are supported now:
* off=0, size=1 (narrow);
* off=1, size=1 (narrow);
* off=2, size=1 (narrow);
* off=3, size=1 (narrow);
* off=0, size=2 (narrow);
* off=2, size=2 (narrow);
* off=0, size=4 (full).
Reported-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The kernel functions to prepare verifier and translate for offloaded
program retrieve "offload" from "prog", and "netdev" from "offload".
Then both "prog" and "netdev" are passed to the callbacks.
Simplify this by letting the drivers retrieve the net device themselves
from the offload object attached to prog - if they need it at all. There
is currently no need to pass the netdev as an argument to those
functions.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Function bpf_prog_offload_verifier_prep(), called from the kernel BPF
verifier to run a driver-specific callback for preparing for the
verification step for offloaded programs, takes a pointer to a struct
bpf_verifier_env object. However, no driver callback needs the whole
structure at this time: the two drivers supporting this, nfp and
netdevsim, only need a pointer to the struct bpf_prog instance held by
env.
Update the callback accordingly, on kernel side and in these two
drivers.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
As part of the transition from ndo_bpf() to callbacks attached to struct
bpf_offload_dev for some of the eBPF offload operations, move the
functions related to program destruction to the struct and remove the
subcommand that was used to call them through the NDO.
Remove function __bpf_offload_ndo(), which is no longer used.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
As part of the transition from ndo_bpf() to callbacks attached to struct
bpf_offload_dev for some of the eBPF offload operations, move the
functions related to code translation to the struct and remove the
subcommand that was used to call them through the NDO.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In a way similar to the change previously brought to the verify_insn
hook and to the finalize callback, switch to the newly added ops in
struct bpf_prog_offload for calling the functions used to prepare driver
verifiers.
Since the dev_ops pointer in struct bpf_prog_offload is no longer used
by any callback, we can now remove it from struct bpf_prog_offload.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
We intend to remove the dev_ops in struct bpf_prog_offload, and to only
keep the ops in struct bpf_offload_dev instead, which is accessible from
more locations for passing function pointers.
But dev_ops is used for calling the verify_insn hook. Switch to the
newly added ops in struct bpf_prog_offload instead.
To avoid table lookups for each eBPF instruction to verify, we remember
the offdev attached to a netdev and modify bpf_offload_find_netdev() to
avoid performing more than once a lookup for a given offload object.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
For passing device functions for offloaded eBPF programs, there used to
be no place where to store the pointer without making the non-offloaded
programs pay a memory price.
As a consequence, three functions were called with ndo_bpf() through
specific commands. Now that we have struct bpf_offload_dev, and since
none of those operations rely on RTNL, we can turn these three commands
into hooks inside the struct bpf_prog_offload_ops, and pass them as part
of bpf_offload_dev_create().
This commit effectively passes a pointer to the struct to
bpf_offload_dev_create(). We temporarily have two struct
bpf_prog_offload_ops instances, one under offdev->ops and one under
offload->dev_ops. The next patches will make the transition towards the
former, so that offload->dev_ops can be removed, and callbacks relying
on ndo_bpf() added to offdev->ops as well.
While at it, rename "nfp_bpf_analyzer_ops" as "nfp_bpf_dev_ops" (and
similarly for netdevsim).
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull drm fixes from Dave Airlie:
"drm: i915, amdgpu, sun4i, exynos and etnaviv fixes:
- amdgpu has some display fixes, KFD ioctl fixes and a Vega20 bios
interaction fix.
- sun4i has some NULL checks added
- i915 has a 32-bit system fix, LPE audio oops, and HDMI2.0 clock
fixes.
- Exynos has a 3 regression fixes (one frame counter, fbdev missing,
dsi->panel check)
- Etnaviv has a single fencing fix for GPU recovery"
* tag 'drm-fixes-2018-11-11' of git://anongit.freedesktop.org/drm/drm: (39 commits)
drm/amd/amdgpu/dm: Fix dm_dp_create_fake_mst_encoder()
drm/amd/display: Drop reusing drm connector for MST
drm/amd/display: Cleanup MST non-atomic code workaround
drm/amd/powerplay: always use fast UCLK switching when UCLK DPM enabled
drm/amd/powerplay: set a default fclk/gfxclk ratio
drm/amdgpu/display/dce11: only enable FBC when selected
drm/amdgpu/display/dm: handle FBC dc feature parameter
drm/amdgpu/display/dc: add FBC to dc_config
drm/amdgpu: add DC feature mask module parameter
drm/amdgpu/display: check if fbc is available in set_static_screen_control (v2)
drm/amdgpu/vega20: add CLK base offset
drm/amd/display: Stop leaking planes
drm/amd/display: Fix misleading buffer information
Revert "drm/amd/display: set backlight level limit to 1"
drm/amd: Update atom_smu_info_v3_3 structure
drm/i915: Fix ilk+ watermarks when disabling pipes
drm/sun4i: tcon: prevent tcon->panel dereference if NULL
drm/sun4i: tcon: fix check of tcon->panel null pointer
drm/i915: Don't oops during modeset shutdown after lpe audio deinit
drm/i915: Mark pin flags as u64
...
Just replace it with a field of the same name in struct ide_req.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The phy core provides a handy phy_speed_to_str() helper, so use that
instead of doing our own formatting of the different known link speeds.
To do this, increase PHY_LED_TRIGGER_SPEED_SUFFIX_SIZE to 11 so we can fit
'Unsupported' if necessary.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a heritage from the very early days of phylib member interrupts is
defined as u32 even though it's just a flag whether interrupts are
enabled. So we can change it to a bitfield member. In addition change
the code dealing with this member in a way that it's clear we're
dealing with a bool value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a driver provides gettimex64(), use it in the PTP_SYS_OFFSET ioctl
and POSIX clock's gettime() instead of gettime64(). Drivers should
provide only one of the functions.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP_SYS_OFFSET ioctl, which can be used to measure the offset
between a PHC and the system clock, includes the total time that the
driver needs to read the PHC timestamp.
This typically involves reading of multiple PCI registers (sometimes in
multiple iterations) and the register that contains the lowest bits of
the timestamp is not read in the middle between the two readings of the
system clock. This asymmetry causes the measured offset to have a
significant error.
Introduce a new ioctl, driver function, and helper functions, which
allow the reading of the lowest register to be isolated from the other
readings in order to reduce the asymmetry. The ioctl returns three
timestamps for each measurement:
- system time right before reading the lowest bits of the PHC timestamp
- PHC time
- system time immediately after reading the lowest bits of the PHC
timestamp
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the last use of the old BLKPREP_* values, which get converted
to BLK_STS_* later anyway.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace the old BLKPREP_* values with the BLK_STS_ ones that they are
converted to later anyway.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The return value is just used as a binary yes/no decision, so switch
it to a bool instead of the old BLKPREP_* values returned as an int.
Also clean up a few related comments.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull Ceph fixes from Ilya Dryomov:
"Two CephFS fixes (copy_file_range and quota) and a small feature bit
cleanup"
* tag 'ceph-for-4.20-rc2' of https://github.com/ceph/ceph-client:
libceph: assume argonaut on the server side
ceph: quota: fix null pointer dereference in quota check
ceph: add destination file data sync before doing any remote copy
We have introduced some battery properties to present the OCV table
temperatures and OCV capacity table values. Thus this patch add OCV
temperature and OCV table for battery information, as well as providing
some helper functions to use the OCV capacity table for users.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Pull overlay validation checks from Frank Rowand:
"Add checks to (1) overlay apply process and (2) memory freeing
triggered by overlay release. The checks are intended to detect
possible memory leaks and invalid overlays.
The checks revealed bugs in existing code. Fixed the bugs.
While fixing bugs, noted other issues, which are fixed in
separate patches."
Signed-off-by: Rob Herring <robh@kernel.org>
There are no users of of_pdt_build_more since 2012, so remove it.
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
No users of this type anywhere in the tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the static inline function uart_handle_break() in serial_core.h we
dereference port->cons. That gives an error unless console.h is also
included.
This error hasn't shown up till now because everyone who has defined
SUPPORT_SYSRQ has also included console.h, but it's a bit ugly to make
this requirement. Let's make the include explicit.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now serial drivers process sysrq keys deep in their character
receiving code. This means that they've already grabbed their
port->lock spinlock. This can end up getting in the way if we've go
to do serial stuff (especially kgdb) in response to the sysrq.
Serial drivers have various hacks in them to handle this. Looking at
'8250_port.c' you can see that the console_write() skips locking if
we're in the sysrq handler. Looking at 'msm_serial.c' you can see
that the port lock is dropped around uart_handle_sysrq_char().
It turns out that these hacks aren't exactly perfect. If you have
lockdep turned on and use something like the 8250_port hack you'll get
a splat that looks like:
WARNING: possible circular locking dependency detected
[...] is trying to acquire lock:
... (console_owner){-.-.}, at: console_unlock+0x2e0/0x5e4
but task is already holding lock:
... (&port_lock_key){-.-.}, at: serial8250_handle_irq+0x30/0xe4
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&port_lock_key){-.-.}:
_raw_spin_lock_irqsave+0x58/0x70
serial8250_console_write+0xa8/0x250
univ8250_console_write+0x40/0x4c
console_unlock+0x528/0x5e4
register_console+0x2c4/0x3b0
uart_add_one_port+0x350/0x478
serial8250_register_8250_port+0x350/0x3a8
dw8250_probe+0x67c/0x754
platform_drv_probe+0x58/0xa4
really_probe+0x150/0x294
driver_probe_device+0xac/0xe8
__driver_attach+0x98/0xd0
bus_for_each_dev+0x84/0xc8
driver_attach+0x2c/0x34
bus_add_driver+0xf0/0x1ec
driver_register+0xb4/0x100
__platform_driver_register+0x60/0x6c
dw8250_platform_driver_init+0x20/0x28
...
-> #0 (console_owner){-.-.}:
lock_acquire+0x1e8/0x214
console_unlock+0x35c/0x5e4
vprintk_emit+0x230/0x274
vprintk_default+0x7c/0x84
vprintk_func+0x190/0x1bc
printk+0x80/0xa0
__handle_sysrq+0x104/0x21c
handle_sysrq+0x30/0x3c
serial8250_read_char+0x15c/0x18c
serial8250_rx_chars+0x34/0x74
serial8250_handle_irq+0x9c/0xe4
dw8250_handle_irq+0x98/0xcc
serial8250_interrupt+0x50/0xe8
...
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&port_lock_key);
lock(console_owner);
lock(&port_lock_key);
lock(console_owner);
*** DEADLOCK ***
The hack used in 'msm_serial.c' doesn't cause the above splats but it
seems a bit ugly to unlock / lock our spinlock deep in our irq
handler.
It seems like we could defer processing the sysrq until the end of the
interrupt handler right after we've unlocked the port. With this
scheme if a whole batch of sysrq characters comes in one irq then we
won't handle them all, but that seems like it should be a fine
compromise.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This happened while running in qemu-system-aarch64, the AMBA PL011 UART
driver when enabling CONFIG_DEBUG_TEST_DRIVER_REMOVE.
arch_initcall(pl011_init) came before subsys_initcall(default_bdi_init),
devtmpfs' handle_remove() crashes because the reference count is a NULL
pointer only because wb->bdi hasn't been initialized yet.
Rework so that wb_put have an extra check if wb->bdi before decrement
wb->refcnt and also add a WARN_ON_ONCE to get a warning if it happens again
in other drivers.
Fixes: 52ebea749a ("writeback: make backing_dev_info host cgroup-specific bdi_writebacks")
Co-developed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current CAN framework can't guarantee proper/chronological order
of RX and TX-ECHO messages. To make this possible, drivers should use
this functions instead of can_get_echo_skb().
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch factors out all non sending parts of can_get_echo_skb() into
a seperate function __can_get_echo_skb(), so that it can be re-used in
an upcoming patch.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pull s390 fixes from Martin Schwidefsky:
- A fix for the pgtable_bytes misaccounting on s390. The patch changes
common code part in regard to page table folding and adds extra
checks to mm_[inc|dec]_nr_[pmds|puds].
- Add FORCE for all build targets using if_changed
- Use non-loadable phdr for the .vmlinux.info section to avoid a
segment overlap that confuses kexec
- Cleanup the attribute definition for the diagnostic sampling
- Increase stack size for CONFIG_KASAN=y builds
- Export __node_distance to fix a build error
- Correct return code of a PMU event init function
- An update for the default configs
* tag 's390-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/perf: Change CPUM_CF return code in event init function
s390: update defconfigs
s390/mm: Fix ERROR: "__node_distance" undefined!
s390/kasan: increase instrumented stack size to 64k
s390/cpum_sf: Rework attribute definition for diagnostic sampling
s390/mm: fix mis-accounting of pgtable_bytes
mm: add mm_pxd_folded checks to pgtable_bytes accounting functions
mm: introduce mm_[p4d|pud|pmd]_folded
mm: make the __PAGETABLE_PxD_FOLDED defines non-empty
s390: avoid vmlinux segments overlap
s390/vdso: add missing FORCE to build targets
s390/decompressor: add missing FORCE to build targets
This adds inexact lists per destination network, stored in a search tree.
Inexact lookups now return two 'candidate lists', the 'any' policies
('any' destionations), and a list of policies that share same
daddr/prefix.
Next patch will add a second search tree for 'saddr:any' policies
so we can avoid placing those on the 'any:any' list too.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
At this time inexact policies are all searched in-order until the first
match is found. After removal of the flow cache, this resolution has
to be performed for every packetm resulting in major slowdown when
number of inexact policies is high.
This adds infrastructure to later sort inexact policies into a tree.
This only introduces a single class: any:any.
Next patch will add a search tree to pre-sort policies that
have a fixed daddr/prefixlen, so in this patch the any:any class
will still be used for all policies.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Switch packet-path lookups for inexact policies to rhashtable.
In this initial version, we now no longer need to search policies with
non-matching address family and type.
Next patch will add the if_id as well so lookups from the xfrm interface
driver only need to search inexact policies for that device.
Future patches will augment the hlist in each rhash bucket with a tree
and pre-sort policies according to daddr/prefix.
A single rhashtable is used. In order to avoid a full rhashtable walk on
netns exit, the bins get placed on a pernet list, i.e. we add almost no
cost for network namespaces that had no xfrm policies.
The inexact lists are kept in place, and policies are added to both the
per-rhash-inexact list and a pernet one.
The latter is needed for the control plane to handle migrate -- these
requests do not consider the if_id, so if we'd remove the inexact_list
now we would have to search all hash buckets and then figure
out which matching policy candidate is the most recent one -- this appears
a bit harder than just keeping the 'old' inexact list for this purpose.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
When peering is in userspace, some implementations may want to control
which peers are accepted based on RSSI in addition to the information
elements being sent today. Add signal level so that info is available
to clients.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When userspace is controlling mesh routing, it may have better
knowledge about whether a mesh STA is connected to a mesh
gate than the kernel mpath table. Add dot11MeshConnectedToMeshGate
to the mesh config so that such applications can explicitly
signal that a mesh STA is connected to a gate, which will then
be advertised in the beacon.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Capture the current state of gate connectivity from the mesh
formation field in mesh config whenever we receive a beacon,
and report that via GET_STATION. This allows applications
doing mesh peering in userspace to make peering decisions
based on peers' current upstream connectivity.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, like in the rsi driver hardware scan offload, there
may be scenarios in which hardware scan might not be available or
desirable.
Allow drivers to cope with this by letting them fall back to software
scan by returning the special value 1 from the hardware scan method.
Requested-by: Sushant Kumar Mishra <sushant2k1513@gmail.com>
Requested-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
