Pull SoC update from Arnd Bergmann:
"Convert ep93xx to devicetree
This concludes a long journey towards replacing the old board files
with devictree description on the Cirrus Logic EP93xx platform.
Nikita Shubin has been working on this for a long time, for details
see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/"
* tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
dt-bindings: gpio: ep9301: Add missing "#interrupt-cells" to examples
MAINTAINERS: Update EP93XX ARM ARCHITECTURE maintainer
soc: ep93xx: drop reference to removed EP93XX_SOC_COMMON config
net: cirrus: use u8 for addr to calm down sparse
dmaengine: cirrus: use snprintf() to calm down gcc 13.3.0
dmaengine: ep93xx: Fix a NULL vs IS_ERR() check in probe()
pinctrl: ep93xx: Fix raster pins typo
spi: ep93xx: update kerneldoc comments for ep93xx_spi
clk: ep93xx: Fix off by one in ep93xx_div_recalc_rate()
clk: ep93xx: add module license
dmaengine: cirrus: remove platform code
ASoC: cirrus: edb93xx: Delete driver
ARM: ep93xx: soc: drop defines
ARM: ep93xx: delete all boardfiles
ata: pata_ep93xx: remove legacy pinctrl use
pwm: ep93xx: drop legacy pinctrl
ARM: ep93xx: DT for the Cirrus ep93xx SoC platforms
ARM: dts: ep93xx: Add EDB9302 DT
ARM: dts: ep93xx: add ts7250 board
ARM: dts: add Cirrus EP93XX SoC .dtsi
...
Pull char / misc driver updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystem changes
for 6.12-rc1.
Lots of changes in here, primarily dominated by the usual IIO driver
updates and additions, but there are also small driver subsystem
updates all over the place. Included in here are:
- lots and lots of new IIO drivers and updates to existing ones
- interconnect subsystem updates and new drivers
- nvmem subsystem updates and new drivers
- mhi driver updates
- power supply subsystem updates
- kobj_type const work for many different small subsystems
- comedi driver fix
- coresight subsystem and driver updates
- fpga subsystem improvements
- slimbus fixups
- binder new feature addition for "frozen" notifications
- lots and lots of other small driver updates and cleanups
All of these have been in linux-next for a long time with no reported
problems"
* tag 'char-misc-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (354 commits)
greybus: gb-beagleplay: Add firmware upload API
arm64: dts: ti: k3-am625-beagleplay: Add bootloader-backdoor-gpios to cc1352p7
dt-bindings: net: ti,cc1352p7: Add bootloader-backdoor-gpios
MAINTAINERS: Update path for U-Boot environment variables YAML
nvmem: layouts: add U-Boot env layout
comedi: ni_routing: tools: Check when the file could not be opened
ocxl: Remove the unused declarations in headr file
hpet: Fix the wrong format specifier
uio: Constify struct kobj_type
cxl: Constify struct kobj_type
binder: modify the comment for binder_proc_unlock
iio: adc: axp20x_adc: add support for AXP717 ADC
dt-bindings: iio: adc: Add AXP717 compatible
iio: adc: axp20x_adc: Add adc_en1 and adc_en2 to axp_data
w1: ds2482: Drop explicit initialization of struct i2c_device_id::driver_data to 0
tools: iio: rm .*.cmd when make clean
iio: adc: standardize on formatting for id match tables
iio: proximity: aw96103: Add support for aw96103/aw96105 proximity sensor
bus: mhi: host: pci_generic: Enable EDL trigger for Foxconn modems
bus: mhi: host: pci_generic: Update EDL firmware path for Foxconn modems
...
Pull input updates from Dmitry Torokhov:
- support for PixArt PS/2 touchpad
- updates to tsc2004/5, usbtouchscreen, and zforce_ts drivers
- support for GPIO-only mode for ADP55888 controller
- support for touch keys in Zinitix driver
- support for querying density of Synaptics sensors
- sysfs interface for Goodex "Berlin" devices to read and write touch
IC registers
- more quirks to i8042 to handle various Tuxedo laptops
- a number of drivers have been converted to using "guard" notation
when acquiring various locks, as well as using other cleanup
functions to simplify releasing of resources (with more drivers to
follow)
- evdev will limit amount of data that can be written into an evdev
instance at a given time to 4096 bytes (170 input events) to avoid
holding evdev->mutex for too long and starving other users
- Spitz has been converted to use software nodes/properties to describe
its matrix keypad and GPIO-connected LEDs
- msc5000_ts, msc_touchkey and keypad-nomadik-ske drivers have been
removed since noone in mainline have been using them
- other assorted cleanups and fixes
* tag 'input-for-v6.12-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (98 commits)
ARM: spitz: fix compile error when matrix keypad driver is enabled
Input: hynitron_cstxxx - drop explicit initialization of struct i2c_device_id::driver_data to 0
Input: adp5588-keys - fix check on return code
Input: Convert comma to semicolon
Input: i8042 - add TUXEDO Stellaris 15 Slim Gen6 AMD to i8042 quirk table
Input: i8042 - add another board name for TUXEDO Stellaris Gen5 AMD line
Input: tegra-kbc - use of_property_read_variable_u32_array() and of_property_present()
Input: ps2-gpio - use IRQF_NO_AUTOEN flag in request_irq()
Input: ims-pcu - fix calling interruptible mutex
Input: zforce_ts - switch to using asynchronous probing
Input: zforce_ts - remove assert/deassert wrappers
Input: zforce_ts - do not hardcode interrupt level
Input: zforce_ts - switch to using devm_regulator_get_enable()
Input: zforce_ts - stop treating VDD regulator as optional
Input: zforce_ts - make zforce_idtable constant
Input: zforce_ts - use dev_err_probe() where appropriate
Input: zforce_ts - do not ignore errors when acquiring regulator
Input: zforce_ts - make parsing of contacts less confusing
Input: zforce_ts - switch to using get_unaligned_le16
Input: zforce_ts - use guard notation when acquiring mutexes
...
Pull dmaengine updates from Vinod Koul:
"Unusually, more new driver and device support than updates. Couple of
new device support, AMD, Rcar, Intel and New drivers in Freescale,
Loonsoon, AMD and LPC32XX with DT conversion and mode updates etc.
New support:
- Support for AMD Versal Gen 2 DMA IP
- Rcar RZ/G3S SoC dma controller
- Support for Intel Diamond Rapids and Granite Rapids-D dma controllers
- Support for Freescale ls1021a-qdma controller
- New driver for Loongson-1 APB DMA
- New driver for AMD QDMA
- Pl08x in LPC32XX router dma driver
Updates:
- Support for dpdma cyclic dma mode
- XML conversion for marvell xor dma bindings
- Dma clocks documentation for imx dma"
* tag 'dmaengine-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (24 commits)
dmaengine: loongson1-apb-dma: Fix the build warning caused by the size of pdev_irqname
dmaengine: Fix spelling mistakes
dmaengine: Add dma router for pl08x in LPC32XX SoC
dmaengine: fsl-edma: add edma src ID check at request channel
dmaengine: fsl-edma: change to guard(mutex) within fsl_edma3_xlate()
dmaengine: avoid non-constant format string
dmaengine: imx-dma: Remove i.MX21 support
dt-bindings: dma: fsl,imx-dma: Document the DMA clocks
dmaengine: Loongson1: Add Loongson-1 APB DMA driver
dt-bindings: dma: Add Loongson-1 APB DMA
dmaengine: zynqmp_dma: Add support for AMD Versal Gen 2 DMA IP
dt-bindings: dmaengine: zynqmp_dma: Add a new compatible string
dmaengine: idxd: Add new DSA and IAA device IDs for Diamond Rapids platform
dmaengine: idxd: Add a new DSA device ID for Granite Rapids-D platform
dmaengine: ti: k3-udma: Remove unused declarations
dmaengine: amd: qdma: Add AMD QDMA driver
dmaengine: xilinx: dpdma: Add support for cyclic dma mode
dma: ipu: Remove include/linux/dma/ipu-dma.h
dt-bindings: dma: fsl-mxs-dma: Add compatible string "fsl,imx8qxp-dma-apbh"
dt-bindings: fsl-qdma: allow compatible string fallback to fsl,ls1021a-qdma
...
Pull x86 platform drivers updates from Hans de Goede:
- asus-wmi: Add support for vivobook fan profiles
- dell-laptop: Add knobs to change battery charge settings
- lg-laptop: Add operation region support
- intel-uncore-freq: Add support for efficiency latency control
- intel/ifs: Add SBAF test support
- intel/pmc: Ignore all LTRs during suspend
- platform/surface: Support for arm64 based Surface devices
- wmi: Pass event data directly to legacy notify handlers
- x86/platform/geode: switch GPIO buttons and LEDs to software
properties
- bunch of small cleanups, fixes, hw-id additions, etc.
* tag 'platform-drivers-x86-v6.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (65 commits)
MAINTAINERS: adjust file entry in INTEL MID PLATFORM
platform/x86: x86-android-tablets: Adjust Xiaomi Pad 2 bottom bezel touch buttons LED
platform/mellanox: mlxbf-pmc: fix lockdep warning
platform/x86/amd: pmf: Add quirk for TUF Gaming A14
platform/x86: touchscreen_dmi: add nanote-next quirk
platform/x86: asus-wmi: don't fail if platform_profile already registered
platform/x86: asus-wmi: add debug print in more key places
platform/x86: intel_scu_wdt: Move intel_scu_wdt.h to x86 subfolder
platform/x86: intel_scu_ipc: Move intel_scu_ipc.h out of arch/x86/include/asm
MAINTAINERS: Add Intel MID section
platform/x86: panasonic-laptop: Add support for programmable buttons
platform/olpc: Remove redundant null pointer checks in olpc_ec_setup_debugfs()
platform/x86: intel/pmc: Ignore all LTRs during suspend
platform/x86: wmi: Call both legacy and WMI driver notify handlers
platform/x86: wmi: Merge get_event_data() with wmi_get_notify_data()
platform/x86: wmi: Remove wmi_get_event_data()
platform/x86: wmi: Pass event data directly to legacy notify handlers
platform/x86: thinkpad_acpi: Fix uninitialized symbol 's' warning
platform/x86: x86-android-tablets: Fix spelling in the comments
platform/x86: ideapad-laptop: Make the scope_guard() clear of its scope
...
Pull hwmon updates from Guenter Roeck:
"New drivers:
- driver for Sophgo SG2042 external hardware monitor
- thermal sensor driver for Surface Aggregator Module
Added support to existing drivers:
- oxp-sensors: Support for multiple new devices.
- nct6775: Added G15CF to ASUS WMI monitoring list
Modernizations:
- driver cleanup and update to use with_info API: ina2xx, lm92,
lm95234, max1619, max1668, and max6697.
API updates:
- removed unused devm_hwmon_device_unregister() API function
Other notable changes
- implement and use generic bus access delay for pmbus drivers
- use with scoped for each OF child loop in several drivers
- module unloading fixes for gsc-hwmon and ntc_thermistor drivers
- converted various drivers to use multi-byte regmap operations
- adt7475: Improved devicetree based configuration
- ltc2947: Move to firmware agnostic API
- ltc2978: Converted devicetree description to yaml
- max16065: Addressed overflows when writing limit attributes
Various other minor cleanups, fixes and improvements"
* tag 'hwmon-for-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (96 commits)
hwmon: Remove devm_hwmon_device_unregister() API function
hwmon: (sch5636) Print unknown ID in error string via %*pE
hwmon: (sht21) Use %*ph to print small buffer
hwmon: (pmbus/mpq7932) Constify struct regulator_desc
hwmon: pmbus: pli12096bc: Add write delay
hwmon: pmbus: zl6100: Use generic code
hwmon: pmbus: ucd9000: Use generic code
hwmon: pmbus: max15301: Use generic code
hwmon: pmbus: Implement generic bus access delay
hwmon: (ina2xx) Use shunt voltage to calculate current
hwmon: (ina2xx) Add support for current limits
hwmon: (ina2xx) Pass register to alert limit write functions
hwmon: (ina2xx) Convert to use with_info hwmon API
hwmon: (ina2xx) Move ina2xx_get_value()
hwmon: (ina2xx) Set alert latch
hwmon: (ina2xx) Consolidate chip initialization code
hwmon: (ina2xx) Fix various overflow issues
hwmon: (ina2xx) Re-initialize chip using regmap functions
hwmon: (ina2xx) Use local regmap pointer if used more than once
hwmon: (ina2xx) Mark regmap_config as const
...
Pull gpio updates from Bartosz Golaszewski:
"Core GPIOLIB:
- provide and add users for a macro allowing to iterate over accepted
GPIO property names of consumer device nodes
- remove legacy definitions that are no longer used
- put legacy GPIO devres helpers together with the rest of the
deprecated code
- implement and use swnode_gpio_get_reference(): a wrapper
simplifying the underlying calls to
fwnode_property_get_reference_args()
- use IS_ERR_OR_NULL() where it makes sense
- replace of_find_property() with of_property_present()
- simplify code with the scoped variant of OF-node children iterator
Documentation:
- update GPIO kerneldocs with Return sections
- fix "Excess struct member description" warnings now being triggered
with W=1
New drivers:
- add support for Analog Devices ADP5585
Driver improvements:
- add support for wake-on-GPIO to gpio-mpc8xxx
- use GPIO_LOOKUP_IDX() in gpio-virtuser
- use devm_clk_get_[optional_]enabled() where applicable in several
drivers
- replace OF-specific functions with provider-agnostic alternatives
where possible
- drop support for legacy platform data from gpio-ath79 and
gpio-davinci
- refactor gpio-stmpe
- improve error reporting in gpio-pca953x
- add support for reading the direction of pins for some models to
gpio-vf610
DT bindings:
- convert the bindings for nxp,lpc3220 to YAML
- add gpio-reserved-ranges to gpio-davinci
- simplify the GPIO hog schema
- fix a GPIO hog issue in bindings for fcs,fxl6408
Other:
- fix format specifiers in user-space tools
- remove leftover files on make clean in tools/gpio/"
* tag 'gpio-updates-for-v6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (54 commits)
gpio: mpc8xxx: switch to using DEFINE_RUNTIME_DEV_PM_OPS()
gpio: xilinx: Use helper function devm_clk_get_optional_enabled()
gpio: mb86s7x: Use helper function devm_clk_get_optional_enabled()
gpio: lpc18xx: Use helper function devm_clk_get_enabled()
gpio: cadence: Use helper function devm_clk_get_enabled()
gpio: sama5d2-piobu: convert comma to semicolon
gpio: mpc8xxx: order headers alphabetically
gpio: davinci: use devm_clk_get_enabled()
gpio: davinci: drop platform data support
gpio: stmpe: Sort headers
gpio: stmpe: Make use of device properties
gpio: stmpe: Utilise temporary variable for struct device
gpio: stmpe: Remove unused 'dev' member of struct stmpe_gpio
gpio: stmpe: Fix IRQ related error messages
gpio: pch: kerneldoc fixes for excess members
gpio: zynq: Simplify using devm_clk_get_enabled()
gpio: mpc8xxx: Add wake on GPIO support
gpio: syscon: fix excess struct member build warning
gpio: stp-xway: Simplify using devm_clk_get_enabled()
gpiolib: legacy: Consolidate devm_gpio_*() with other legacy APIs
...
Pull MTD updates from Miquel Raynal:
"MTD changes:
- No particularly important patchset this cycle, but we have a few
usual improvements: like using a better/more recent helper or
checking a return value.
Raw NAND changes:
- The use of for_each_child_of_node_scoped() has been spread into the
subsystem drivers
- a couple of exit path have been fixed (mtk, denali)
- TI GPMC bindings have been enhanced to comply with up-to-date
partition descriptions
- a load of small and misc fixes
SPI-NAND changes:
- The most impacting series this cycle is bringing support for
continuous reads in the SPI-NAND subsystem.
This is a feature already merged in the raw NAND subsystem which
allows optimizing the internal fetch times in the chip while
reading sequential pages within an eraseblock.
For now only Macronix NANDs benefit from this feature. While we are
talking about Macronix, some of their chip need an explicit action
for selecting a different plane, and support for it has also been
brought.
- The bitflip threshold has also been set to the same arbitrary level
as in the raw NAND subsystem to optimize wear leveling decisions
- Add upport for a new Winbond chip
SPI NOR changes:
- Add Write Protect support for N25Q064A.
- New flash support for Zetta ZD25Q128C and Spansion S28HS256T.
- Fix a NULL dereference in probe path for flashes without a name.
The probe path tries to access the name without checking its
existence first. S28HS256T is the first flash to define its entry
without a name, uncovering this issue"
* tag 'mtd/for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (41 commits)
mtd: spi-nor: fix flash probing
mtd: spi-nor: spansion: Add support for S28HS256T
mtd: spi-nor: winbond: add Zetta ZD25Q128C support
mtd: spi-nor: micron-st: Add n25q064a WP support
mtd: spi-nor: sst: Factor out common write operation to `sst_nor_write_data()`
mtd: spinand: macronix: Flag parts needing explicit plane select
mtd: spinand: Add support for setting plane select bits
dt-bindings: mtd: ti, gpmc-nand: support partitions node
mtd: rawnand: mtk: Fix init error path
mtd: powernv: Add check devm_kasprintf() returned value
mtd: rawnand: mtk: Factorize out the logic cleaning mtk chips
mtd: rawnand: atmel: Add message on DMA usage
mtd: rawnand: meson: Fix typo in function name
mtd: spi-nand: macronix: Continuous read support
mtd: spi-nand: macronix: Add a possible bitflip status flag
mtd: spi-nand: macronix: Extract the bitflip retrieval logic
mtd: spi-nand: macronix: Fix helper name
mtd: spi-nand: Expose spinand_write_reg_op()
mtd: spi-nand: Add continuous read support
mtd: spi-nand: Isolate the MTD read logic in a helper
...
Pull SoC driver updates from Arnd Bergmann:
"The driver updates seem larger this time around, with changes is many
of the SoC specific drivers, both the custom drivers/soc ones and the
closely related subsystems (memory, bus, firmware, reset, ...).
The at91 platform gains support for sam9x7 chips in the soc and power
management code. This is the latest variant of one of the oldest still
supported SoC families, using the ARM9 (ARMv5) core.
As usual, the qualcomm snapdragon platform gets a ton of updates in
many of their drivers to add more features and additional SoC support.
Most of these are somewhat firmware related as the platform has a
number of firmware based interfaces to the kernel. A notable addition
here is the inclusion of trace events to two of these drivers.
Herve Codina and Christophe Leroy are now sending updates for
drivers/soc/fsl/ code through the SoC tree, this contains both PowerPC
and Arm specific platforms and has previously been problematic to
maintain. The first update here contains support for newer PowerPC
variants and some cleanups.
The turris mox firmware driver has a number of updates, mostly
cleanups.
The Arm SCMI firmware driver gets a major rework to modularize the
existing code into separately loadable drivers for the various
transports, the addition of custom NXP i.MX9 interfaces and a number
of smaller updates.
The Arm FF-A firmware driver gets a feature update to support the v1.2
version of the specification.
The reset controller drivers have some smaller cleanups and a newly
added driver for the Intel/Mobileye EyeQ5/EyeQ6 MIPS SoCs.
The memory controller drivers get some cleanups and refactoring for
Tegra, TI, Freescale/NXP and a couple more platforms.
Finally there are lots of minor updates to firmware (raspberry pi,
tegra, imx), bus (sunxi, omap, tegra) and soc (rockchips, tegra,
amlogic, mediatek) drivers and their DT bindings"
* tag 'soc-drivers-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (212 commits)
firmware: imx: remove duplicate scmi_imx_misc_ctrl_get()
platform: cznic: turris-omnia-mcu: Fix error check in omnia_mcu_register_trng()
bus: sunxi-rsb: Simplify code with dev_err_probe()
soc: fsl: qe: ucc: Export ucc_mux_set_grant_tsa_bkpt
soc: fsl: cpm1: qmc: Fix dependency on fsl_soc.h
dt-bindings: arm: rockchip: Add rk3576 compatible string to pmu.yaml
soc: fsl: qbman: Remove redundant warnings
soc: fsl: qbman: Use iommu_paging_domain_alloc()
MAINTAINERS: Add QE files related to the Freescale QMC controller
soc: fsl: cpm1: qmc: Handle QUICC Engine (QE) soft-qmc firmware
soc: fsl: cpm1: qmc: Add support for QUICC Engine (QE) implementation
soc: fsl: qe: Add missing PUSHSCHED command
soc: fsl: qe: Add resource-managed muram allocators
soc: fsl: cpm1: qmc: Introduce qmc_version
soc: fsl: cpm1: qmc: Rename SCC_GSMRL_MODE_QMC
soc: fsl: cpm1: qmc: Handle RPACK initialization
soc: fsl: cpm1: qmc: Rename qmc_chan_command()
soc: fsl: cpm1: qmc: Introduce qmc_{init,exit}_xcc() and their CPM1 version
soc: fsl: cpm1: qmc: Introduce qmc_init_resource() and its CPM1 version
soc: fsl: cpm1: qmc: Re-order probe() operations
...
Cross-merge networking fixes after downstream PR.
No conflicts (sort of) and no adjacent changes.
This merge reverts commit b3c9e65eb2 ("net: hsr: remove seqnr_lock")
from net, as it was superseded by
commit 430d67bdcb ("net: hsr: Use the seqnr lock for frames received via interlink port.")
in net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert Cirrus EP93xx DMA to device tree usage:
- add OF ID match table with data
- add of_probe for device tree
- add xlate for m2m/m2p
- drop subsys_initcall code
- drop platform probe
- drop platform structs usage
>From now on it only supports device tree probing.
Co-developed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Replace ksz8830 with ksz88x3 for CHIP_ID definition and other
strings. This due to KSZ8830 not being an actual switch but the Chip
ID shared among KSZ8863/8873 switches, impossible to differentiate
from their Chip ID or Revision ID registers.
Now all KSZ*_CHIP_ID macros refer to actual, existing switches which
removes confusion.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds driver to enable PCIe board which uses AMD QDMA (the Queue-based
Direct Memory Access) subsystem. For example, Xilinx Alveo V70 AI
Accelerator devices.
https://www.xilinx.com/applications/data-center/v70.html
The QDMA subsystem is used in conjunction with the PCI Express IP block
to provide high performance data transfer between host memory and the
card's DMA subsystem.
+-------+ +-------+ +-----------+
PCIe | | | | | |
Tx/Rx | | | | AXI | |
<=======> | PCIE | <===> | QDMA | <====>| User Logic|
| | | | | |
+-------+ +-------+ +-----------+
The primary mechanism to transfer data using the QDMA is for the QDMA
engine to operate on instructions (descriptors) provided by the host
operating system. Using the descriptors, the QDMA can move data in both
the Host to Card (H2C) direction, or the Card to Host (C2H) direction.
The QDMA provides a per-queue basis option whether DMA traffic goes
to an AXI4 memory map (MM) interface or to an AXI4-Stream interface.
The hardware detail is provided by
https://docs.xilinx.com/r/en-US/pg302-qdma
Implements dmaengine APIs to support MM DMA transfers.
- probe the available DMA channels
- use dma_slave_map for channel lookup
- use virtual channel to manage dmaengine tx descriptors
- implement device_prep_slave_sg callback to handle host scatter gather
list
Signed-off-by: Nishad Saraf <nishads@amd.com>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://lore.kernel.org/r/20240819211948.688786-2-lizhi.hou@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
KSZ8895/KSZ8864 is a switch family between KSZ8863/73 and KSZ8795, so it
shares some registers and functions in those switches already
implemented in the KSZ DSA driver.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Tested-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The cyttsp4 touchscreen driver was contributed in 2013 and since then
has seen no updates. The driver uses platform data (no device tree
support) and there are no users of it in the mainline kernel. There were
occasional fixes to it for issues either found by static code analysis
tools or via visual inspection, but otherwise the driver is completely
untested.
Remove the driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/ZrAZ2cUow_z838tp@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On almost all ASUS ROG series laptops the MCU used for the USB keyboard
also has a HID packet used for setting the brightness. This is usually
the same as the WMI method. But in some laptops the WMI method either
is missing or doesn't work, so we should default to the HID control.
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Acked-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240713074733.77334-2-luke@ljones.dev
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add support for vivobook fan profiles wmi call on the ASUS VIVOBOOK
to adjust power limits.
These fan profiles have a different device id than the ROG series
and different order. This reorders the existing modes.
As part of keeping the patch clean the throttle_thermal_policy_available
boolean stored in the driver struct is removed and
throttle_thermal_policy_dev is used in place (as on init it is zeroed).
Co-developed-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Mohamed Ghanmi <mohamed.ghanmi@supcom.tn>
Reviewed-by: Luke D. Jones <luke@ljones.dev>
Link: https://lore.kernel.org/r/20240609144849.2532-2-mohamed.ghanmi@supcom.tn
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Platform data is not used anywhere in the upstram kernel.
Drop support for it to simplify code maintenance.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some hardware need some time to switch from a bus to another. This can
cause the first transfers following the selection of a bus to fail.
There is no way to configure this kind of waiting time in the driver.
Add support for the 'settle-time-us' device-tree property. When set,
the i2c_mux_gpio_select() applies a delay before returning, leaving
enough time to the hardware to switch to the new bus.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Pull MFD updates from Lee Jones:
"New Drivers:
- ROHM BD96801 Power Management IC
- Cirrus Logic CS40L50 Haptic Driver with Waveform Memory
- Marvell 88PM886 Power Management IC
New Device Support:
- Keyboard Backlight to ChromeOS Embedded Controller
- LEDs to ChromeOS Embedded Controller
- Charge Control to ChromeOS Embedded Controller
- HW Monitoring Service to ChromeOS Embedded Controller
- AUXADCs to MediaTek MT635{7,8,9} Power Management ICs
New Functionality:
- Allow Syscon consumers to supply their own Regmaps on registration
Fix-ups:
- Constify/staticise applicable data structures
- Remove superfluous/duplicated/unused sections
- Device Tree binding adaptions/conversions/creation
- Trivial; spelling, whitespace, coding-style adaptions
- Utilise centrally provided helpers and macros to aid
simplicity/duplication
- Drop i2c_device_id::driver_data where the value is unused
- Replace ACPI/DT firmware helpers with agnostic variants
- Move over to GPIOD (descriptor-based) APIs
- Annotate a bunch of __counted_by() cases
- Straighten out some includes
Bug Fixes:
- Ensure potentially asserted recent lines are deasserted during
initialisation
- Avoid "<module>.ko is added to multiple modules" warnings
- Supply a bunch of MODULE_DESCRIPTIONs to silence modpost warnings
- Fix Wvoid-pointer-to-enum-cast warnings"
* tag 'mfd-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (87 commits)
mfd: timberdale: Attach device properties to TSC2007 board info
mfd: tmio: Move header to platform_data
mfd: tmio: Sanitize comments
mfd: tmio: Update include files
mmc: tmio/sdhi: Fix includes
mfd: tmio: Remove obsolete io accessors
mfd: tmio: Remove obsolete platform_data
watchdog: bd96801_wdt: Add missing include for FIELD_*()
dt-bindings: mfd: syscon: Add APM poweroff mailbox
dt-bindings: mfd: syscon: Split and enforce documenting MFD children
dt-bindings: mfd: rk817: Merge support for RK809
dt-bindings: mfd: rk817: Fixup clocks and reference dai-common
dt-bindings: mfd: syscon: Add TI's opp table compatible
mfd: omap-usb-tll: Use struct_size to allocate tll
dt-bindings: mfd: Explain lack of child dependency in simple-mfd
dt-bindings: mfd: Dual licensing for st,stpmic1 bindings
mfd: omap-usb-tll: Annotate struct usbtll_omap with __counted_by
mfd: tps6594-core: Remove unneeded semicolon in tps6594_check_crc_mode()
mfd: lm3533: Move to new GPIO descriptor-based APIs
mfd: tps65912: Use devm helper functions to simplify probe
...
Pull x86 platform driver updates from Ilpo Järvinen:
- amd/pmf: Report system state changes using existing input events
- asus-wmi: Zenbook 2023 camera LED disable support and fix TUF laptop
keyboard RGB LED sysfs interface
- dell-pc: Fan modes / platform profile support
- hp-wmi: Fix platform profile switching on Omen/Victus laptops
- intel/ISST: Use only TPMI interface when TPMI and legacy interfaces
are available
- intel/pmc: LTR restore support to pair with LTR ignore
- intel/tpmi: Performance Limit Reasons (PLR) and APIC <-> Punit CPU
numbering mapping support
- WMI: driver override support and docs improvements
- lenovo-yoga-c630: Support for EC (platform/arm64)
- platform/arm64: Fix build with COMPILE_TEST (broke after addition of
C630)
- tools: Intel Speed Select Turbo Ratio Limit fix
- Miscellaneous cleanups / refactoring / improvements
* tag 'platform-drivers-x86-v6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (65 commits)
platform/x86: asus-wmi: fix TUF laptop RGB variant
platform/x86/intel/tpmi/plr: Fix output in plr_print_bits()
Docs/admin-guide: Remove pmf leftover reference from the index
platform/x86: ideapad-laptop: use cleanup.h
platform/x86: hp-wmi: Fix implementation of the platform_profile_omen_get function
platform: arm64: EC_LENOVO_YOGA_C630 should depend on ARCH_QCOM
platform: arm64: EC_ACER_ASPIRE1 should depend on ARCH_QCOM
platform/x86/amd/pmf: Remove update system state document
platform/x86/amd/pmf: Use existing input event codes to update system states
platform/x86: hp-wmi: Fix platform profile option switch bug on Omen and Victus laptops
platform/x86:intel/pmc: Add support to undo ltr_ignore
platform/x86:intel/pmc: Use the Elvis operator
platform/x86:intel/pmc: Use DEFINE_SHOW_STORE_ATTRIBUTE macro
platform/x86:intel/pmc: Remove unneeded min_t check
platform/x86:intel/pmc: Add support to show ltr_ignore value
platform/x86:intel/pmc: Move pmc assignment closer to first usage
platform/x86:intel/pmc: Convert index variables to be unsigned
platform/x86:intel/pmc: Simplify mutex usage with cleanup helpers
platform/x86:intel/pmc: Use the return value of pmc_core_send_msg
tools/power/x86/intel-speed-select: v1.20 release
...
Pull thermal control updates from Rafael Wysocki:
"These add some new hardware support (notably, the Lunar Lake platform
support in int340x and X1E80100 temperature sensor), continue to
rework the thermal driver interface to eliminate trip point IDs from
it, update DT bindings for a number of platforms and simplify probe in
a number of thermal drivers, address issues and clean up code.
Specifics:
- Add DLVR and MSI interrupt support for the Lunar Lake platform to
the int340x thermal driver (Srinivas Pandruvada)
- Enable workload type hints (WLT) support and power floor interrupt
support for the Lunar Lake platform in int340x ((Srinivas
Pandruvada)
- Switch Intel thermal drivers to new Intel CPU model defines (Tony
Luck)
- Clean up the int3400 and int3403 drivers (Erick Archer and David
Alan Gilbert)
- Improve intel_pch_thermal kernel log messages printed during
suspend to idle (Zhang Rui)
- Make the intel_tcc_cooling driver use a model-specific bitmask for
TCC offset (Ricardo Neri)
- Redesign the .set_trip_temp() thermal zone callback to take a trip
pointer instead of a trip ID and update its users (Rafael Wysocki)
- Avoid using invalid combinations of polling_delay and passive_delay
thermal zone parameters (Rafael Wysocki)
- Update a cooling device registration function to take a const
argument (Krzysztof Kozlowski)
- Make the uniphier thermal driver use thermal_zone_for_each_trip()
for walking trip points (Rafael Wysocki)
- Fix and clean up several minor shortcomings in thermal debug
(Rafael Wysocki)
- Rename __thermal_zone_set_trips() to thermal_zone_set_trips() and
make it use trip thresholds (Rafael Wysocki)
- Use READ_ONCE() for lockless access to trip temperature and
hysteresis (Rafael Wysocki)
- Drop unnecessary cooling device target state checks from the
Bang-Bang thermal governor (Rafael Wysocki)
- Avoid invoking thermal governor .trip_crossed() callback for
critical and hot trip points (Rafael Wysocki)
- Group all Renesas drivers inside a dedicated sub directory and add
the missing dependency to OF (Niklas Söderlund)
- Add suspend/resume support on k3_j72xx_bandgap and take the
opportunity to remove an unneeded delay in the init time code path
(Théo Lebrun)
- Fix thermal zone definition for MT8186 and MT8188 (Julien Panis)
- Convert hisilicon-thermal.txt to dt-schema (Abdulrasaq Lawani)
- Add DT bindings for the X1E80100 temperature sensor (Abel Vesa)
- Fix the thermal zone node name regular expression in the DT schema
(Krzysztof Kozlowski)
- Avoid failing thermal control initialization by using default
values on some platforms where calibration data is missing (Chen-Yu
Tsai)
- Fix the sensor cell size in DT for the Exynos platform (Krzysztof
Kozlowski)
- Bring the common definition of '#thermal-sensor-cells' property in
order to simplify the bindings on all the platforms where this
change makes sense and do some minor cleanups (Krzysztof Kozlowski)
- Fix a race between removal and clock disable in the broadcom
thermal driver (Krzysztof Kozlowski)
- Drop 'trips' DT node as required from the thermal zone bindings in
order to fix the remaining warnings appearing for thermal zones
without trip points (Rob Herring)
- Simplify all the drivers where dev_err_probe() can apply (Krzysztof
Kozlowski)
- Clean up code related to stih416 as this platform is not described
anywhere (Raphael Gallais-Pou)"
* tag 'thermal-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (81 commits)
thermal/drivers/sti: Cleanup code related to stih416
thermal/drivers/generic-adc: Simplify with dev_err_probe()
thermal/drivers/generic-adc: Simplify probe() with local dev variable
thermal/drivers/qcom-tsens: Simplify with dev_err_probe()
thermal/drivers/qcom-spmi-adc-tm5: Simplify with dev_err_probe()
thermal/drivers/imx: Simplify with dev_err_probe()
thermal/drivers/imx: Simplify probe() with local dev variable
thermal/drivers/hisi: Simplify with dev_err_probe()
thermal/drivers/exynos: Simplify with dev_err_probe()
thermal/drivers/exynos: Simplify probe() with local dev variable
thermal/drivers/broadcom: Simplify with dev_err_probe()
thermal/drivers/broadcom: Simplify probe() with local dev variable
thermal/drivers/broadcom: Fix race between removal and clock disable
dt-bindings: thermal: Drop 'trips' node as required
dt-bindings: thermal: qoriq: reference thermal-sensor schema
dt-bindings: thermal: cleanup examples indentation
dt-bindings: thermal: simplify few bindings
dt-bindings: thermal: ti,j72xx: reference thermal-sensor schema
dt-bindings: thermal: ti,am654: reference thermal-sensor schema
dt-bindings: thermal: st,stm32: reference thermal-sensor schema
...
Pull arm SoC platform updates from Arnd Bergmann:
"The majority of the updates here are Dmitry Torokhov's cleanups for
platform code in the pxa and tegra platforms, changing custom
platform_data structures into DT-compatible software node
declarations.
The other updates are for the MAINTAINERS file, correcting some stale
or missing entries"
* tag 'soc-arm-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: pxa: fix build breakage on PXA3xx
ti: omap: MAINTAINERS: move Benoît Cousson to CREDITS
amazon: MAINTAINERS: change to odd fixes and Tsahee Zidenberg to CREDITS
MAINTAINERS: thead: add git tree
ARM: spitz: Use software nodes for the ADS7846 touchscreen
ARM: spitz: Use software nodes to describe LED GPIOs
ARM: spitz: Use software nodes to describe MMC GPIOs
ARM: spitz: Use software nodes to describe LCD GPIOs
ARM: spitz: Use software nodes to describe audio GPIOs
ARM: spitz: Use software nodes to describe SPI CS lines
ARM: spitz: Simplify instantiating SPI controller
ARM: pxa/gumstix: convert vbus gpio to use software nodes
ARM: pxa: consolidate GPIO chip platform data
ARM: spitz: fix GPIO assignment for backlight
ARM: tegra: paz00: Use software nodes to describe GPIOs for WiFi rfkill
MAINTAINERS: ARM: airoha: add entry to cover Airoha SoC
bus: vexpress-config: Add missing MODULE_DESCRIPTION() macro
arm64: layerscape: remove redundant EDAC_SUPPORT selection
dt-bindings: arm: Remove obsolete RTSM DCSCB binding
arm: vexpress: Remove obsolete RTSM DCSCB support
MCS-5000/5080 chips belong to the 1st generation of Melfas chips,
manufactured in 2000-2007.
The driver relies on custom platform data (no DT support) and there
never were any users of this driver in the mainline kernel. It is likely
that the driver was (like mcs5000_ts driver) was tested on S3C6410 NCP
board (with Samsung S3C6410 SoC), but the touchkey device was never
added to the board file. This board was removed in v6.3 in commit
743c8fbb90 ("ARM: s3c: remove most s3c64xx board support").
Remove the driver since there are no users.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240714060029.1528662-2-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MCS-5000 belongs to the 1st generation of Melfas chips, manufactured in
2000-2007.
The driver relies on custom platform data (no DT support) and there
never were any users of this driver in the mainline kernel. The commit
adding the driver mentioned that the driver was tested on S3C6410 NCP
board (with Samsung S3C6410 SoC) but the touchscreen device was never
added to the board file. This board was removed in v6.3 in commit
743c8fbb90 ("ARM: s3c: remove most s3c64xx board support").
Remove the driver since there are no users.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240714060029.1528662-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Retrieving the supported versions of a command is a fairly common
operation. Provide a helper for it.
If the command is not supported at all the EC returns
-EINVAL/EC_RES_INVALID_PARAMS.
This error is translated into an empty version mask as that is easier to
handle for callers and they don't need to know about the error details.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20240630-cros_ec-charge-control-v5-3-8f649d018c52@weissschuh.net
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
To read from the EC memory different mechanism are possible.
ECs connected via LPC expose their memory via a ->cmd_readmem operation.
Other protocols require the usage of EC_CMD_READ_MEMMAP, which on the
other hand is not implemented by LPC ECs.
Provide a helper that automatically selects the correct mechanism.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240529-cros_ec-hwmon-v4-1-5cdf0c5db50a@weissschuh.net
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Pull char/misc and other driver subsystem updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem updates
for 6.10-rc1. Nothing major here, just lots of new drivers and updates
for apis and new hardware types. Included in here are:
- big IIO driver updates with more devices and drivers added
- fpga driver updates
- hyper-v driver updates
- uio_pruss driver removal, no one uses it, other drivers control the
same hardware now
- binder minor updates
- mhi driver updates
- excon driver updates
- counter driver updates
- accessability driver updates
- coresight driver updates
- other hwtracing driver updates
- nvmem driver updates
- slimbus driver updates
- spmi driver updates
- other smaller misc and char driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (319 commits)
misc: ntsync: mark driver as "broken" to prevent from building
spmi: pmic-arb: Add multi bus support
spmi: pmic-arb: Register controller for bus instead of arbiter
spmi: pmic-arb: Make core resources acquiring a version operation
spmi: pmic-arb: Make the APID init a version operation
spmi: pmic-arb: Fix some compile warnings about members not being described
dt-bindings: spmi: Deprecate qcom,bus-id
dt-bindings: spmi: Add X1E80100 SPMI PMIC ARB schema
spmi: pmic-arb: Replace three IS_ERR() calls by null pointer checks in spmi_pmic_arb_probe()
spmi: hisi-spmi-controller: Do not override device identifier
dt-bindings: spmi: hisilicon,hisi-spmi-controller: clean up example
dt-bindings: spmi: hisilicon,hisi-spmi-controller: fix binding references
spmi: make spmi_bus_type const
extcon: adc-jack: Document missing struct members
extcon: realtek: Remove unused of_gpio.h
extcon: usbc-cros-ec: Convert to platform remove callback returning void
extcon: usb-gpio: Convert to platform remove callback returning void
extcon: max77843: Convert to platform remove callback returning void
extcon: max3355: Convert to platform remove callback returning void
extcon: intel-mrfld: Convert to platform remove callback returning void
...
