moxart_mac_start_xmit() doesn't care where tx_tail is, tx_head can
catch and pass tx_tail, which is bad because moxart_tx_finished()
isn't guaranteed to catch up on freeing resources from tx_tail.
Add a check in moxart_mac_start_xmit() stopping the queue at the
end of the circular buffer. Also add a check in moxart_tx_finished()
waking the queue if the buffer has TX_WAKE_THRESHOLD or more
free descriptors.
While we're at it, move spin_lock_irq() to happen before our
descriptor pointer is assigned in moxart_mac_start_xmit().
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=99451
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-7 points out that the AVMB1_ADDCARD ioctl results in an unintialized
value ending up in the cardnr parameter:
drivers/isdn/capi/kcapi.c: In function 'old_capi_manufacturer':
drivers/isdn/capi/kcapi.c:1042:24: error: 'cdef.cardnr' may be used uninitialized in this function [-Werror=maybe-uninitialized]
cparams.cardnr = cdef.cardnr;
This has been broken since before the start of the git history, so
either the value is not used for anything important, or the ioctl
command doesn't get called in practice.
Setting the cardnr to zero avoids the warning and makes sure
we have consistent behavior.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlsi_alloc_ring() checks for DMA mapping errors by comparing
returned address with zero, while pci_dma_mapping_error() should be used.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns_dsaf_set_mac_key() calls dsaf_set_field() on an uninitialized field,
which will then change only a few of its bits, causing a warning with
the latest gcc:
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_set_mac_uc_entry':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
(origin) &= (~(mask)); \
^~
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_set_mac_mc_entry':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_add_mac_mc_port':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_del_mac_entry':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_rm_mac_addr':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_del_mac_mc_port':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_get_mac_uc_entry':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_get_mac_mc_entry':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The code is actually correct since we always set all 16 bits of the
port_vlan field, but gcc correctly points out that the first
access does contain uninitialized data.
This initializes the field to zero first before setting the
individual bits.
Fixes: 5483bfcb16 ("net: hns: modify tcam table and set mac key")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dev_dbg() is enabled, we print uninitialized data, as gcc-7.0.1
now points out:
ethernet/hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_set_promisc_tcam':
ethernet/hisilicon/hns/hns_dsaf_main.c:2947:75: error: 'tbl_tcam_data.low.val' may be used uninitialized in this function [-Werror=maybe-uninitialized]
ethernet/hisilicon/hns/hns_dsaf_main.c:2947:75: error: 'tbl_tcam_data.high.val' may be used uninitialized in this function [-Werror=maybe-uninitialized]
We also pass the data into hns_dsaf_tcam_mc_cfg(), which might later
use it (not sure about that), so it seems safer to just always initialize
the tbl_tcam_data structure.
Fixes: 1f5fa2dd1c ("net: hns: fix for promisc mode in HNS driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing the epoll w/ busy poll code I found that I could get into a
state where the i40e driver had q_vectors w/ active NAPI that had no rings.
This was resulting in a divide by zero error. To correct it I am updating
the driver code so that we only support NAPI on q_vectors that have 1 or
more rings allocated to them.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 7e54d9d063.
After additional regression testing, several users are experiencing
kernel panics during shutdown on e1000e devices. Reverting this
change resolves the issue.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The latest gcc-7 snapshot warns about bfa_ioc_send_enable/bfa_ioc_send_disable
writing undefined values into the hardware registers:
drivers/net/ethernet/brocade/bna/bfa_ioc.c: In function 'bfa_iocpf_sm_disabling_entry':
arch/arm/include/asm/io.h:109:22: error: '*((void *)&disable_req+4)' is used uninitialized in this function [-Werror=uninitialized]
arch/arm/include/asm/io.h:109:22: error: '*((void *)&disable_req+8)' is used uninitialized in this function [-Werror=uninitialized]
The two functions look like they should do the same thing, but only one
of them initializes the time stamp and clscode field. The fact that we
only get a warning for one of the two functions seems to be arbitrary,
based on the inlining decisions in the compiler.
To address this, I'm making both functions do the same thing:
- set the clscode from the ioc structure in both
- set the time stamp from ktime_get_real_seconds (which also
avoids the signed-integer overflow in 2038 and extends the
well-defined behavior until 2106).
- zero-fill the reserved field
Fixes: 8b230ed8ec ("bna: Brocade 10Gb Ethernet device driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
With AF_IUCV traffic, the skb passed to hard_start_xmit() has a 14 byte
slot at skb->data, intended for an ETH header. qeth_l3_fill_af_iucv_hdr()
fills this ETH header... and then immediately moves it to the
skb's headroom, where it disappears and is never seen again.
But it's still possible for us to return NETDEV_TX_BUSY after the skb has
been modified. Since we didn't get a private copy of the skb, the next
time the skb is delivered to hard_start_xmit() it no longer has the
expected layout (we moved the ETH header to the headroom, so skb->data
now starts at the IUCV_TRANS header). So when qeth_l3_fill_af_iucv_hdr()
does another round of rebuilding, the resulting qeth header ends up
all wrong. On transmission, the buffer is then rejected by
the HiperSockets device with SBALF15 = x'04'.
When this error is passed back to af_iucv as TX_NOTIFY_UNREACHABLE, it
tears down the offending socket.
As the ETH header for AF_IUCV serves no purpose, just align the code to
what we do for IP traffic on L3 HiperSockets: keep the ETH header at
skb->data, and pass down data_offset = ETH_HLEN to qeth_fill_buffer().
When mapping the payload into the SBAL elements, the ETH header is then
stripped off. This avoids the skb manipulations in
qeth_l3_fill_af_iucv_hdr(), and any buffer re-entering hard_start_xmit()
after NETDEV_TX_BUSY is now processed properly.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the device type, hard_start_xmit() builds different output
buffer formats. For instance with HiperSockets, on both L2 and L3 we
strip the ETH header from the skb - L3 doesn't need it, and L2 carries
it in the buffer's header element.
For this, we pass data_offset = ETH_HLEN all the way down to
__qeth_fill_buffer(), where skb->data is then adjusted accordingly.
But the initial size calculation still considers the *full* skb length
(including the ETH header). So qeth_get_elements_no() can erroneously
reject a skb as too big, even though it would actually fit into an
output buffer once the ETH header has been trimmed off later.
Fix this by passing an additional offset to qeth_get_elements_no(),
that indicates where in the skb the on-wire data actually begins.
Since the current code uses data_offset=-1 for some special handling
on OSA, we need to clamp data_offset to 0...
On HiperSockets this helps when sending ~MTU-size skbs with weird page
alignment. No change for OSA or AF_IUCV.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to reset is_gso flag when EOP reached (entire LSO packet processed).
Fixes: bab6de8fd1 ("net: ethernet: aquantia:
Atlantic A0 and B0 specific functions.")
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix Context Command bit: L3 type = "0" for IPv4, "1" for IPv6.
Fixes: bab6de8fd1 ("net: ethernet: aquantia:
Atlantic A0 and B0 specific functions.")
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix for missing initialization aq_ring header.lock spinlock.
Fixes: 018423e90b ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the checksum offloads to work correctly we need to set the
packet type bit (TCP/UDP) in the TX context buffer.
Fixes: 97bde5c4f9 ("net: ethernet: aquantia: Support for NIC-specific code")
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Tested-by: David Arcari <darcari@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Closing/opening the adapter is not needed at all.
The new MTU settings take effect immediately.
Fixes: 97bde5c4f9 ("net: ethernet: aquantia: Support for NIC-specific code")
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The linking status may be changed when autosuspend. And, after
autoresume, the driver may try to transmit packets when the device
is carrier off, because the interrupt transfer doesn't update the
linking status, yet. And, if the device is in ALDPS mode, the device
would stop working.
The another similar case is
1. unplug the cable.
2. interrupt transfer queue a work_queue for linking change.
3. device enters the ALDPS mode.
4. a tx occurs before the work_queue is called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the PHY is halted on stop, then do not set the state to PHY_UP. This
ensures the phy will be restarted later in phy_start when the machine is
started again.
Fixes: 00db8189d9 ("This patch adds a PHY Abstraction Layer to the Linux Kernel, enabling ethernet drivers to remain as ignorant as is reasonable of the connected PHY's design and operation details.")
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Acked-by: Xander Huff <xander.huff@ni.com>
Acked-by: Kyle Roeschley <kyle.roeschley@ni.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can build modular code that uses mdiobus_register_board_info() which would
lead to linking failure since this symbol is not expoerted.
Fixes: 648ea01340 ("net: phy: Allow pre-declaration of MDIO devices")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Several netfilter fixes from Pablo and the crew:
- Handle fragmented packets properly in netfilter conntrack, from
Florian Westphal.
- Fix SCTP ICMP packet handling, from Ying Xue.
- Fix big-endian bug in nftables, from Liping Zhang.
- Fix alignment of fake conntrack entry, from Steven Rostedt.
2) Fix feature flags setting in fjes driver, from Taku Izumi.
3) Openvswitch ipv6 tunnel source address not set properly, from Or
Gerlitz.
4) Fix jumbo MTU handling in amd-xgbe driver, from Thomas Lendacky.
5) sk->sk_frag.page not released properly in some cases, from Eric
Dumazet.
6) Fix RTNL deadlocks in nl80211, from Johannes Berg.
7) Fix erroneous RTNL lockdep splat in crypto, from Herbert Xu.
8) Cure improper inflight handling during AF_UNIX GC, from Andrey
Ulanov.
9) sch_dsmark doesn't write to packet headers properly, from Eric
Dumazet.
10) Fix SCM_TIMESTAMPING_OPT_STATS handling in TCP, from Soheil Hassas
Yeganeh.
11) Add some IDs for Motorola qmi_wwan chips, from Tony Lindgren.
12) Fix nametbl deadlock in tipc, from Ying Xue.
13) GRO and LRO packets not counted correctly in mlx5 driver, from Gal
Pressman.
14) Fix reset of internal PHYs in bcmgenet, from Doug Berger.
15) Fix hashmap allocation handling, from Alexei Starovoitov.
16) nl_fib_input() needs stronger netlink message length checking, from
Eric Dumazet.
17) Fix double-free of sk->sk_filter during sock clone, from Daniel
Borkmann.
18) Fix RX checksum offloading in aquantia driver, from Pavel Belous.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (85 commits)
net:ethernet:aquantia: Fix for RX checksum offload.
amd-xgbe: Fix the ECC-related bit position definitions
sfc: cleanup a condition in efx_udp_tunnel_del()
Bluetooth: btqcomsmd: fix compile-test dependency
inet: frag: release spinlock before calling icmp_send()
tcp: initialize icsk_ack.lrcvtime at session start time
genetlink: fix counting regression on ctrl_dumpfamily()
socket, bpf: fix sk_filter use after free in sk_clone_lock
ipv4: provide stronger user input validation in nl_fib_input()
bpf: fix hashmap extra_elems logic
enic: update enic maintainers
net: bcmgenet: remove bcmgenet_internal_phy_setup()
ipv6: make sure to initialize sockc.tsflags before first use
fjes: Do not load fjes driver if extended socket device is not power on.
fjes: Do not load fjes driver if system does not have extended socket device.
net/mlx5e: Count LRO packets correctly
net/mlx5e: Count GSO packets correctly
net/mlx5: Increase number of max QPs in default profile
net/mlx5e: Avoid supporting udp tunnel port ndo for VF reps
net/mlx5e: Use the proper UAPI values when offloading TC vlan actions
...
Since AQC-100/107/108 chips supports hardware checksums for RX we should indicate this
via NETIF_F_RXCSUM flag.
v1->v2: 'Signed-off-by' tag added.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ECC bit positions that describe whether the ECC interrupt is for
Tx, Rx or descriptor memory and whether the it is a single correctable
or double detected error were defined in incorrectly (reversed order).
Fix the bit position definitions for these settings so that the proper
ECC handling is performed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Presumably if there is an "add" function, there is also a "del"
function. But it causes a static checker warning because it looks like
a common cut and paste bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
compile-testing fails when QCOM_SMD is a loadable module:
drivers/bluetooth/built-in.o: In function `btqcomsmd_send':
btqca.c:(.text+0xa8): undefined reference to `qcom_smd_send'
drivers/bluetooth/built-in.o: In function `btqcomsmd_probe':
btqca.c:(.text+0x3ec): undefined reference to `qcom_wcnss_open_channel'
btqca.c:(.text+0x46c): undefined reference to `qcom_smd_set_drvdata'
This clarifies the dependency to allow compile-testing only when
SMD is completely disabled, otherwise the dependency on QCOM_SMD
will make sure we can link against it.
Fixes: e27ee2b16b ("Bluetooth: btqcomsmd: Allow driver to build if COMPILE_TEST is enabled")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[bjorn: Restructure and clarify dependency to QCOM_WCNSS_CTRL]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset")
removed the bcmgenet_mii_reset() function from bcmgenet_power_up() and
bcmgenet_internal_phy_setup() functions. In so doing it broke the reset
of the internal PHY devices used by the GENETv1-GENETv3 which required
this reset before the UniMAC was enabled. It also broke the internal
GPHY devices used by the GENETv4 because the config_init that installed
the AFE workaround was no longer occurring after the reset of the GPHY
performed by bcmgenet_phy_power_set() in bcmgenet_internal_phy_setup().
In addition the code in bcmgenet_internal_phy_setup() related to the
"enable APD" comment goes with the bcmgenet_mii_reset() so it should
have also been removed.
Commit bd4060a610 ("net: bcmgenet: Power on integrated GPHY in
bcmgenet_power_up()") moved the bcmgenet_phy_power_set() call to the
bcmgenet_power_up() function, but failed to remove it from the
bcmgenet_internal_phy_setup() function. Had it done so, the
bcmgenet_internal_phy_setup() function would have been empty and could
have been removed at that time.
Commit 5dbebbb44a ("net: bcmgenet: Software reset EPHY after power on")
was submitted to correct the functional problems introduced by
commit 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset"). It
was included in v4.4 and made available on 4.3-stable. Unfortunately,
it didn't fully revert the commit because this bcmgenet_mii_reset()
doesn't apply the soft reset to the internal GPHY used by GENETv4 like
the previous one did. This prevents the restoration of the AFE work-
arounds for internal GPHY devices after the bcmgenet_phy_power_set() in
bcmgenet_internal_phy_setup().
This commit takes the alternate approach of removing the unnecessary
bcmgenet_internal_phy_setup() function which shouldn't have been in v4.3
so that when bcmgenet_mii_reset() was restored it should have only gone
into bcmgenet_power_up(). This will avoid the problems while also
removing the redundancy (and hopefully some of the confusion).
Fixes: 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The extended device socket cannot turn on/off while system is running.
So when system boots up and the device is not power on, the fjes driver
does not need be loaded.
To check the status of the device, the patch adds ACPI _STA method check.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
CC: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fjes driver is used only by FUJITSU servers and almost of all
servers in the world never use it. But currently if ACPI PNP0C02
is defined in the ACPI table, the following message is always shown:
"FUJITSU Extended Socket Network Device Driver - version 1.2
- Copyright (c) 2015 FUJITSU LIMITED"
The message makes users confused because there is no reason that
the message is shown in other vendor servers.
To avoid the confusion, the patch adds a check that the server
has a extended socket device or not.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
CC: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX packets statistics ('rx_packets' counter) used to count LRO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'rx_lro_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 435277
rx_lro_packets: 35847
rx_packets_phy: 1935066
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 1935066
rx_lro_packets: 35847
rx_packets_phy: 1935066
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX packets statistics ('tx_packets' counter) used to count GSO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'tx_tso_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 61340
tx_tso_packets: 60954
tx_packets_phy: 2451115
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 2451115
tx_tso_packets: 60954
tx_packets_phy: 2451115
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With ConnectX-4 sharing SRQs from the same space as QPs, we hit a
limit preventing some applications to allocate needed QPs amount.
Double the size to 256K.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was added to allow the TC offloading code to identify offloading
encap/decap vxlan rules.
The VF reps are effectively related to the same mlx5 PCI device as the
PF. Since the kernel invokes the (say) delete ndo for each netdev, the
FW erred on multiple vxlan dst port deletes when the port was deleted
from the system.
We fix that by keeping the registration to be carried out only by the
PF. Since the PF serves as the uplink device, the VF reps will look
up a port there and realize if they are ok to offload that.
Tested:
<SETUP VFS>
<SETUP switchdev mode to have representors>
ip link add vxlan1 type vxlan id 44 dev ens5f0 dstport 9999
ip link set vxlan1 up
ip link del dev vxlan1
Fixes: 4a25730eb2 ('net/mlx5e: Add ndo_udp_tunnel_add to VF representors')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use the non UAPI values and we miss erring on
the modify action which is not supported, fix that.
Fixes: 8b32580df1 ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the eswitch inline mode can potentially cause already configured
flows not to match the policy. E.g. set policy L4, add some L4 rules,
set policy to L2 --> bad! Hence we disallow it.
Keep track of how many offloaded rules are now set and refuse
inline mode changes if this isn't zero.
Fixes: bffaa91658 ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the code to deal with add/del TC rules to have handler per NIC/E-switch
offloading use case, and push the latter into the e-switch code. This provides
better separation and is to be used in down-stream patch for applying a fix.
Fixes: bffaa91658 ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch cases for the rate limit set and query commands were
missing, which could get us wrong under fw error or driver reset
flow, fix that.
Fixes: 1466cc5b23 ('net/mlx5: Rate limit tables support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers fixes for 4.11
iwlwifi
* fix a user reported warning in DQA
mwifiex
* fix a potential double free
* fix lost early debug logs
* fix init wakeup warning message from device framework
* add Ganapathi and Xinming as maintainers
ath10k
* fix regression with QCA6174 during resume and firmware crash
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With posix timers having become optional, we get a build error with
the cpts time sync option of the CPSW driver:
drivers/net/ethernet/ti/cpts.c: In function 'cpts_find_ts':
drivers/net/ethernet/ti/cpts.c:291:23: error: implicit declaration of function 'ptp_classify_raw';did you mean 'ptp_classifier_init'? [-Werror=implicit-function-declaration]
This adds a hard dependency on PTP_CLOCK to avoid the problem, as
building it without PTP support makes no sense anyway.
Fixes: baa73d9e47 ("posix-timers: Make them configurable")
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dependency is reversed: cpsw and netcp call into cpts,
but cpts depends on the other two in Kconfig. This can lead
to cpts being a loadable module and its callers built-in:
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_remove':
cpsw.c:(.text.cpsw_remove+0xd0): undefined reference to `cpts_release'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_rx_handler':
cpsw.c:(.text.cpsw_rx_handler+0x2dc): undefined reference to `cpts_rx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_tx_handler':
cpsw.c:(.text.cpsw_tx_handler+0x7c): undefined reference to `cpts_tx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_ndo_stop':
As a workaround, I'm introducing another Kconfig symbol to
control the compilation of cpts, while making the actual
module controlled by a silent symbol that is =y when necessary.
Fixes: 6246168b4a ("net: ethernet: ti: netcp: add support of cpts")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
revert commit a59e6d8152 ("r8152: correct the rx early size") and
fix the rx early size as
(rx buffer size - rx packet size - rx desc size - alignment) / 4
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the received maximum size (RMS) according to the mtu size. It is
unnecessary to receive a packet which is more than the size we could
transmit. Besides, this could let the rx buffer be used effectively.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VRF driver takes a reference to the inet6_dev on the VRF device for
its rt6_local dst when handling local traffic through the VRF device as
a loopback. When the device is deleted the driver does a put on the idev
but does not reset rt6i_idev in the rt6_info struct. When the dst is
destroyed, dst_destroy calls ip6_dst_destroy which does a second put for
what is essentially the same reference causing it to be prematurely freed.
Reset rt6i_idev after the put in the vrf driver.
Fixes: b4869aa2f8 ("net: vrf: ipv6 support for local traffic to
local addresses")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We could allocate less memory than intended because we do:
bnad->regdata = kzalloc(len << 2, GFP_KERNEL);
The shift can overflow leading to a crash. This is debugfs code so the
impact is very small.
Fixes: 7afc5dbde0 ("bna: Add debugfs interface.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Rasesh Mody <rasesh.mody@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a Dell branded Sierra Wireless EM7455. It is operating in
MBIM mode by default, but can be configured to provide two QMI/RMNET
functions.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added missing logic in tun driver, which prevents apps to set
offloads using tun ioctl, if offloads were previously disabled via ethtool
Signed-off-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list rx_done would be initialized when the linking on occurs.
Therefore, if a napi is scheduled without any linking on before,
the following kernel panic would happen.
BUG: unable to handle kernel NULL pointer dereference at 000000000000008
IP: [<ffffffffc085efde>] r8152_poll+0xe1e/0x1210 [r8152]
PGD 0
Oops: 0002 [#1] SMP
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull SCSI fixes from James Bottomley:
"Nine small fixes: the biggest is probably finally sorting out Kconfig
issues with lpfc nvme. There are some performance fixes for megaraid
and hpsa and a static checker fix"
[ Johannes Thumshirn points out that there still seems to be more lpfc
vs nvme config issues. Oh well. - Linus ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Finalize Kconfig options for nvme
scsi: ufs: don't check unsigned type for a negative value
scsi: hpsa: do not timeout reset operations
scsi: hpsa: limit outstanding rescans
scsi: hpsa: update check for logical volume status
scsi: megaraid_sas: Driver version upgrade
scsi: megaraid_sas: raid6 also require cpuSel check same as raid5
scsi: megaraid_sas: add correct return type check for ldio hint logic for raid1
scsi: megaraid_sas: enable intx only if msix request fails
Pull HID fixes from Jiri Kosina:
- regression fixes for Wacom devices, from Aaron Armstrong Skomra and
Ping Cheng
- memory leak in hid-sony driver from Roderick Colenbrander
- new device IDs support from Oscar Campos and Daniel Drake
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: generic: Wacom mouse is only provided for opaque tablets
HID: corsair: Add driver Scimitar Pro RGB gaming mouse 1b1c:1b3e support to hid-corsair
HID: corsair: support for K65-K70 Rapidfire and Scimitar Pro RGB
HID: wacom: don't manually release resources for the EKR
HID: wacom: Correct Intuos Pro 2 resolution
HID: sony: Fix input device leak when connecting a DS4 twice using USB/BT
HID: chicony: Add support for another ASUS Zen AiO keyboard
Pull GPIO fixes from Linus Walleij:
"Here is the first set of GPIO fixes for 4.11. It was delayed a bit
beacuse I was chicken when linux-next was not rotating last week.
This hits the ST serial driver in drivers/tty/serial and that has an
ACK from Greg, he suggested to keep the old GPIO fwnode API around to
smoothen things in the merge Windod and those have now served their
purpose so we take them out and convert the last driver to the new
API.
Apart from that it's fixes as usual.
Summary:
- set the parent on the Altera A10SR driver, also fix high level
IRQs.
- fix error path on the mockup driver.
- compilation noise about unused functions fixed.
- fix missed interrupts on the MCP23S08 expander, this is also tagged
for stable.
- retire the interrim helpers devm_get_gpiod_from_child() used to
smoothen merging in the merge window"
* tag 'gpio-v4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio:mcp23s08 Fixed missing interrupts
serial: st-asc: Use new GPIOD API to obtain RTS pin
gpio: altera: Use handle_level_irq when configured as a level_high
gpio: xgene: mark PM functions as __maybe_unused
gpio: mockup: return -EFAULT if copy_from_user() fails
gpio: altera-a10sr: Set gpio_chip parent property
Pull remoteproc fix from Bjorn Andersson:
"This fixes a Kbuild dependency issue related to the Qualcomm
remoteproc drivers"
* tag 'rproc-v4.11-fixes' of git://github.com/andersson/remoteproc:
remoteproc: qcom: fix QCOM_SMD dependencies
