The NAND_NO_AUTOINCR option is always set, so we will kill the option and make
"no autoincrement" the default behavior for nand_base.c. Thus, we should remove
the code which decides whether or not to send the NAND_CMD_READ0 command.
Instead, we unconditionally send the command.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The NAND layer always has NAND_NO_AUTOINCR set, so we will never utilize the
AUTOINCR code in nandsim. We will be removing the NAND_NO_AUTOINCR option soon,
and so kill this code as well.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The drivers' _read() method, absent an error, returns a non-negative integer
indicating the maximum number of bit errors that were corrected in any one
region comprising an ecc step. MTD returns -EUCLEAN if this is >=
bitflip_threshold, 0 otherwise. If bitflip_threshold is zero, the comparison is
not made since these devices lack ECC and always return zero in the non-error
case (thanks Brian)¹. Note that this is a subtle change to the driver
interface.
This and the preceding patches in this set were tested with ubi on top of the
nandsim and docg4 devices, running the ubi test io_basic from mtd-utils.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-March/040468.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
An element 'bitflip_threshold' is added to struct mtd_info, and also exposed as
a read/write variable in sysfs. This will be used to determine whether or not
mtd_read() returns -EUCLEAN or 0 (absent a hard error). If the driver leaves it
as zero, mtd will set it to a default value of ecc_strength.
This v2 adds the line that propagates bitflip_threshold from the master to the
partitions - thanks Ivan¹.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-April/040900.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
To make sure the NAND chip is properly programmed we need a status
command before each page write. When CONFIG_MTD_NAND_VERIFY_WRITE=y this
assumption is broken when writing multiple pages consecutively. This
patch fixes this.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The original Broadcom partition order has the root fs in front of the
kernel, which resulted in miscalculated partition sizes.
Detect when such an image is on the flash and also reorder the partitions
accordingly.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If a context switch occurs in function omap_wait() just before the
while loop is entered, then upon return from context switch the
timeout may already have elapsed: in that case, status is never
read from NAND device, and omap_wait() returns an error.
This failure has been experimentally observed during stress tests.
This patch ensures a NAND status read is always performed before
returning, as in the generic nand_wait() function.
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
clk_{un}prepare is mandatory for platforms using common clock framework. Since
this driver is used by SPEAr platform, which supports common clock framework,
add clk_{un}prepare() support for it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
clk_{un}prepare is mandatory for platforms using common clock framework. Since
this driver is used by SPEAr platform, which supports common clock framework,
add clk_{un}prepare() support for it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
scb2_flash.c is a PCI driver, but its build fails when CONFIG_PCI
is not enabled, so make it depend on PCI.
drivers/mtd/maps/scb2_flash.c:237:1: warning: data definition has no type or storage class
drivers/mtd/maps/scb2_flash.c:237:1: warning: type defaults to 'int' in declaration of 'module_pci_driver'
drivers/mtd/maps/scb2_flash.c:237:1: warning: parameter names (without types) in function declaration
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If prefetch engine is busy, current code "forgets" to call
dma_unmap_single(), which results in a deadlock later, so add it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some not-supported nand chips may pass the current parsing code,
and get the wrong page size and oob size. Sometimes, it's hard to notice
that you get the wrong values, because there is no warning or error.
So it's useful to print out the page size and oob size in the end of
the parsing function. We can check these values with the datasheet of the nand
chip as soon as possible.
Artem: amend the print a bit
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch converts the drivers in drivers/mtd/* to use module_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As long as there is no other non-const variable marked __initdata in the
same compilation unit it doesn't hurt. If there were one however
compilation would fail with
error: $variablename causes a section type conflict
because a section containing const variables is marked read only and so
cannot contain non-const variables.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Pull three MTD fixes from David Woodhouse:
- Fix a lock ordering deadlock in JFFS2
- Fix an oops in the dataflash driver, triggered by a dummy call to test
whether it has OTP functionality.
- Fix request_mem_region() failure on amsdelta NAND driver.
* tag 'for-linus-3.4-20120513' of git://git.infradead.org/linux-mtd:
mtd: ams-delta: fix request_mem_region() failure
jffs2: Fix lock acquisition order bug in gc path
mtd: fix oops in dataflash driver
Pull a few more GPIO bug fixes from Grant Likely:
"Oops, missed a couple. Here's an updated pull req for GPIO"
A set of PCH bug fixes, and one patch to fix up compile warnings
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/exynos: Fix compiler warnings when non-exynos machines are selected
gpio: pch9: Use proper flow type handlers
Pull SCSI fixes from James Bottomley:
"This is a set of minor qla and virto fixes plus one major regression
fix (oops in all legacy host drivers)."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] virtio_scsi: fix TMF use-after-free
[SCSI] fix oops in all legacy host adapters caused by 6f381fa
[SCSI] qla2xxx: Update version number to 8.04.00.03-k.
[SCSI] qla2xxx: Properly check for current state after the fabric-login request.
[SCSI] qla2xxx: Proper completion to scsi-ml for scsi status task_set_full and busy.
[SCSI] qla2xxx: Block flash access from application when device is initialized for ISP82xx.
[SCSI] qla2xxx: Fix reset time out as qla2xxx not ack to reset request.
Pull networking fixes from David S. Miller:
1) Since we do RCU lookups on ipv4 FIB entries, we have to test if the
entry is dead before returning it to our caller.
2) openvswitch locking and packet validation fixes from Ansis Atteka,
Jesse Gross, and Pravin B Shelar.
3) Fix PM resume locking in IGB driver, from Benjamin Poirier.
4) Fix VLAN header handling in vhost-net and macvtap, from Basil Gor.
5) Revert a bogus network namespace isolation change that was causing
regressions on S390 networking devices.
6) If bonding decides to process and handle a LACPDU frame, we
shouldn't bump the rx_dropped counter. From Jiri Bohac.
7) Fix mis-calculation of available TX space in r8169 driver when doing
TSO, which can lead to crashes and/or hung device. From Julien
Ducourthial.
8) SCTP does not validate cached routes properly in all cases, from
Nicolas Dichtel.
9) Link status interrupt needs to be handled in ks8851 driver, from
Stephen Boyd.
10) Use capable(), not cap_raised(), in connector/userns netlink code.
From Eric W. Biederman via Andrew Morton.
11) Fix pktgen OOPS on module unload, from Eric Dumazet.
12) iwlwifi under-estimates SKB truesizes, also from Eric Dumazet.
13) Cure division by zero in SFC driver, from Ben Hutchings.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
ks8851: Update link status during link change interrupt
macvtap: restore vlan header on user read
vhost-net: fix handle_rx buffer size
bonding: don't increase rx_dropped after processing LACPDUs
connector/userns: replace netlink uses of cap_raised() with capable()
sctp: check cached dst before using it
pktgen: fix crash at module unload
Revert "net: maintain namespace isolation between vlan and real device"
ehea: fix losing of NEQ events when one event occurred early
igb: fix rtnl race in PM resume path
ipv4: Do not use dead fib_info entries.
r8169: fix unsigned int wraparound with TSO
sfc: Fix division by zero when using one RX channel and no SR-IOV
openvswitch: Validation of IPv6 set port action uses IPv4 header
net: compare_ether_addr[_64bits]() has no ordering
cdc_ether: Ignore bogus union descriptor for RNDIS devices
bnx2x: bug fix when loading after SAN boot
e1000: Silence sparse warnings by correcting type
igb, ixgbe: netdev_tx_reset_queue incorrectly called from tx init path
openvswitch: Release rtnl_lock if ovs_vport_cmd_build_info() failed.
...
Pull device-mapper fixes from Alasdair G Kergon:
"Fix a couple of serious memory leaks in device-mapper thin
provisioning and tidy its MODULE_DESCRIPTION.
Mitigate occasional reported hangs associated with multipath scsi_dh
module loading."
* tag 'dm-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm mpath: check if scsi_dh module already loaded before trying to load
dm thin: correct module description
dm thin: fix unprotected use of prepared_discards list
dm thin: reinstate missing mempool_free in cell_release_singleton
If the requested scsi_dh module is already loaded then skip
request_module().
Multipath table loads can hang in an unnecessary __request_module.
Reported-by: Ben Marzinski <bmarzins@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix two places in commit 104655fd4d ("dm thin: support discards") that
didn't use pool->lock to protect against concurrent changes to the
prepared_discards list.
Without this fix, thin_endio() can race with process_discard(), leading
to concurrent list_add()s that result in the processes locking up with
an error like the following:
WARNING: at lib/list_debug.c:32 __list_add+0x8f/0xa0()
...
list_add corruption. next->prev should be prev (ffff880323b96140), but was ffff8801d2c48440. (next=ffff8801d2c485c0).
...
Pid: 17205, comm: kworker/u:1 Tainted: G W O 3.4.0-rc3.snitm+ #1
Call Trace:
[<ffffffff8103ca1f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8103cb16>] warn_slowpath_fmt+0x46/0x50
[<ffffffffa04f6ce6>] ? bio_detain+0xc6/0x210 [dm_thin_pool]
[<ffffffff8124ff3f>] __list_add+0x8f/0xa0
[<ffffffffa04f70d2>] process_discard+0x2a2/0x2d0 [dm_thin_pool]
[<ffffffffa04f6a78>] ? remap_and_issue+0x38/0x50 [dm_thin_pool]
[<ffffffffa04f7c3b>] process_deferred_bios+0x7b/0x230 [dm_thin_pool]
[<ffffffffa04f7df0>] ? process_deferred_bios+0x230/0x230 [dm_thin_pool]
[<ffffffffa04f7e42>] do_worker+0x52/0x60 [dm_thin_pool]
[<ffffffff81056fa9>] process_one_work+0x129/0x450
[<ffffffff81059b9c>] worker_thread+0x17c/0x3c0
[<ffffffff81059a20>] ? manage_workers+0x120/0x120
[<ffffffff8105eabe>] kthread+0x9e/0xb0
[<ffffffff814ceda4>] kernel_thread_helper+0x4/0x10
[<ffffffff8105ea20>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff814ceda0>] ? gs_change+0x13/0x13
---[ end trace 7e0a523bc5e52692 ]---
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix a significant memory leak inadvertently introduced during
simplification of cell_release_singleton() in commit
6f94a4c45a ("dm thin: fix stacked bi_next
usage").
A cell's hlist_del() must be accompanied by a mempool_free().
Use __cell_release() to do this, like before.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fixes the following compiler warnings:
drivers/gpio/gpio-samsung.c: In function ‘samsung_gpiolib_init’:
drivers/gpio/gpio-samsung.c:2980:1: warning: label ‘err_ioremap1’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2978:1: warning: label ‘err_ioremap2’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2976:1: warning: label ‘err_ioremap3’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2974:1: warning: label ‘err_ioremap4’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2722:55: warning: unused variable ‘gpio_base4’ [-Wunused-variable]
drivers/gpio/gpio-samsung.c:455:32: warning: ‘exynos_gpio_cfg’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2126:33: warning: ‘exynos4_gpios_1’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2228:33: warning: ‘exynos4_gpios_2’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2373:33: warning: ‘exynos4_gpios_3’ defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Jean-Francois Dagenais reported:
Configuring a gpio pin with the gpio-pch driver with
"IRQF_TRIGGER_LOW | IRQF_ONESHOT" generates an interrupt storm for
threaded ISR until the ISR thread actually gets to physically clear
the interrupt on the triggering chip!! The immediate observable
symptom is the high CPU usage for my ISR thread task and the
interrupt count in /proc/interrupts incrementing radically.
The driver is wrong in several ways:
1) Using handle_simple_irq() does not provide proper flow control
handling. In the case of oneshot threaded handlers for the
demultiplexed interrupts this results in an interrupt storm because
the simple handler does not deal with masking/unmasking. Even
without threaded oneshot handlers an interrupt storm for level type
interrupts can easily be triggered when the interrupt is disabled
and the interrupt line is activated from the device.
2) Acknowlegding the demultiplexed interrupt before calling the
handler is wrong for level type interrupts.
3) The set_type function unconditionally enables the interrupt. It's
supposed to set the type and nothing else. The unmasking is done by
the core code.
Move the acknowledge code into a separate function and add it to the
demux irqchip callbacks.
Remove the unconditional enabling from the set_type() callback and set
the proper flow handlers depending on the selected type (level/edge).
Reported-and-tested-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull GPIO omap bug fix from Grant Likely.
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/omap: fix incorrect initialization of omap_gpio_mod_init
Pull target fix from Nicholas Bellinger:
"This patch removes some incorrect legacy code to free se_lun_acl
memory in the NodeACL release path that could potentially trigger an
OOPS during shutdown once dynamic -> explicit initiator NodeACL
conversion has occurred.
That said, we've been able to trigger an OOPS in v4.0 code for this
special case when the associated MappedLUNs had not also been made
explicit based on active TPG LUN layout during the conversion, so it
really makes senses to go ahead and drop this extra cruft to avoid any
possible issues here.
This ends up only effecting iscsi-target module code (it's the only
user) and is CC'ed to stable."
* '3.4-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Drop incorrect se_lun_acl release for dynamic -> explict ACL conversion
If a link change interrupt comes in we just clear the interrupt
and continue along without notifying the upper networking layers
that the link has changed. Use the mii_check_link() function to
update the link status whenever a link change interrupt occurs.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet vlan header is not on the packet and kept in the skb->vlan_tci
when it comes from lower dev. This patch inserts vlan header in user
buffer during skb copy on user read.
Signed-off-by: Basil Gor <basil.gor@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
