The current implementation of the usb-conn-gpio driver uses a fixed
"usb-charger" name for all USB connector devices. This causes conflicts
in the power supply subsystem when multiple USB connectors are present,
as duplicate names are not allowed.
Use IDA to manage unique IDs for naming usb connectors (e.g.,
usb-charger-0, usb-charger-1).
Signed-off-by: Chance Yang <chance.yang@kneron.us>
Link: https://lore.kernel.org/r/20250411-work-next-v3-1-7cd9aa80190c@kneron.us
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several usb requests are needed to allow a USB3 link to enter U1/U2
hardware link power management LPM states. Reorder these requests
and send the more significant and likely to succeed first.
This is similar to the change done for disabling LPM
Enable LPM by first sending requests to the upstream hub of the device
SetPortFeature(U1_TIMEOUT)
SetPortFeature(U2_TIMEOUT)
These are more likely to succeed due to the shorter path, and LPM can
be considered enabled as link may go to U1/U2 LPM states after those.
Send the requests to the device after this, they allow the device
to initialte U1/U2 link transitions. Hub can already initiate U1/U2
SetFeature(U1_ENABLE)
SetFeature(U2_ENABLE)
Fail fast and bail out if a requests to the device fails.
This changes device initated LPM policy a bit. Device is no longer
able to initiate U2 if it failed or is not allowed to initiate
U1.
Enabling and disabling Link power management is done as part of
hub work. Avoid trying to send additional USB requests to a device
when there are known issues. It just causes hub work to block for
even longer.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250314142000.93090-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling device initiated USB3 link power management (LPM) may fail for
various reasons such as too long system exit latency, or link issues.
These are not good reason to disable hub initiated LPM U1/U2
states, especially as it requires sending more requests over a
possibly broken link, causing the hub work to block for even longer.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250314142000.93090-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several usb requests are needed to allow or forbid a USB3 link from
going into U1 or U2 hardware link power management (LPM) states.
Fail fast on issues in LPM disabling path. LPM disabling is done in hub
workqueue paths that are often already handling possible link issues.
Enabling and disabling LPM involves four usb requests.
Two requests sent to the upstream hub of the connected device:
SetPortFeature(U1_TIMEOUT)
SetPortFeature(U2_TIMEOUT)
And two to the device itself:
SetFeature(U1_ENABLE)
SetFeature(U2_ENABLE)
The requests to the hub sets the inactivity timeout used by the hub to
know when to initiate U1 and U2 LPM link state transitions.
These requests are also used prevent U1/U2 LPM transitions completely
by passing zero timeout value.
The requsts sent to the device only controls if device is allowed to
initiate U1/U2 transitions. If not enabled then only hub initiates U1/U2
transitions. Hub may block these device initiated attempts.
Reorder and send the hub requests first, these are more likely to succeed
due to shorter path, and we can consider LPM disabled if these succeed
as U1/U2 link state can not be entered after that.
Fail immediately if a request fails, and don't try to enable back LPM
after a failed request, that will just send more LPM requests over a
bad link.
If a device request controlling device initiateed LPM fails then exit
immediately, but consider LPM disabled at this stage.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250314142000.93090-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When creating a device path in the driver the snprintf() takes
up to 16 characters long argument along with the additional up to
12 characters for the signed integer (as it can't see the actual limits)
and tries to pack this into 16 bytes array. GCC complains about that
when build with `make W=1`:
drivers/usb/core/usb.c:705:25: note: ‘snprintf’ output between 3 and 28 bytes into a destination of size 16
Since everything works until now, let's just check for the potential
buffer overflow and bail out. It is most likely a never happen situation,
but at least it makes GCC happy.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250321164949.423957-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On i.MX95 platform, USB wakeup setting is controlled by HSIO Block
Control:
HSIO Block Control Overview:
- The HSIO block control include configuration and status registers that
provide miscellaneous top-level controls for clocking, beat limiter
enables, wakeup signal enables and interrupt status for the PCIe and USB
interfaces.
The wakeup function of HSIO blkctl is basically same as non-core, except
improvements about power lost cases. This will add the wakeup setting for
HSIO blkctl on i.MX95. It will firstly ioremap hsio blkctl memory, then do
wakeup setting as needs.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20250318150908.1583652-4-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the course of fixing up the usages of flexible arrays, Gustavo
submitted a patch updating the ehci-fsl driver. However, the patch
was wrong because the driver was using the .priv member of the
ehci_hcd structure incorrectly. The private data is not supposed to
be a wrapper containing the ehci_hcd structure; it is supposed to be a
sub-structure stored in the .priv member.
Fix the problem by replacing the ehci_fsl structure with
ehci_fsl_priv, containing only the private data, along with a suitable
conversion macro for accessing it. This removes the problem of having
data follow a flexible array member.
Reported-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/linux-usb/Z-R9BcnSzrRv5FX_@kspp/
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/8139e4cc-4e5c-40e2-9c4b-717ad3215868@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't set WDM_READ flag in wdm_in_callback() for ZLP-s, otherwise when
userspace tries to poll for available data, it might - incorrectly -
believe there is something available, and when it tries to non-blocking
read it, it might get stuck in the read loop.
For example this is what glib does for non-blocking read (briefly):
1. poll()
2. if poll returns with non-zero, starts a read data loop:
a. loop on poll() (EINTR disabled)
b. if revents was set, reads data
I. if read returns with EINTR or EAGAIN, goto 2.a.
II. otherwise return with data
So if ZLP sets WDM_READ (#1), we expect data, and try to read it (#2).
But as that was a ZLP, and we are doing non-blocking read, wdm_read()
returns with EAGAIN (#2.b.I), so loop again, and try to read again
(#2.a.).
With glib, we might stuck in this loop forever, as EINTR is disabled
(#2.a).
Signed-off-by: Robert Hodaszi <robert.hodaszi@digi.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250403144004.3889125-1-robert.hodaszi@digi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to how it is done in the write path.
Add a disabled flag to track the function state and use it to exit the read
loops to ensure no readers get stuck when the function is disabled/unbound,
protecting against corruption when the waitq and spinlocks are reinitialized
in hidg_bind().
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20250318152207.330997-1-peter@korsgaard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
Move the conflicting declaration to the end of the structure. Notice
that `struct uvc_input_header_descriptor` is a flexible structure --a
structure that contains a flexible-array member.
With this, fix three of the following warnings:
drivers/usb/gadget/function/uvc_configfs.h:77:57: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/Z9dyY7_ydJiGqh_d@kspp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
strncpy() is deprecated for NUL-terminated destination buffers; use
strscpy() instead. Since kzalloc() already zeroes out the destination
buffer, the potential NUL-padding by strncpy() is unnecessary. strscpy()
copies only the required characters and guarantees NUL-termination.
Since the destination buffer has a fixed length, strscpy() automatically
determines its size using sizeof() when the argument is omitted. This
makes an explicit sizeof() call unnecessary.
The source string is also NUL-terminated and meets the __must_be_cstr()
requirement of strscpy().
No functional changes intended.
Link: https://github.com/KSPP/linux/issues/90
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20250320165647.34859-2-thorsten.blum@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc3 device suspend/resume callbacks were being triggered during system
suspend and resume even if the device was already runtime-suspended.
This is redundant for device mode because the suspend and resume routines
are essentially identical for system PM and runtime PM.
To prevent these unnecessary callbacks, indicate to the PM core that it
can safely leave the device in runtime suspend if it's already
runtime-suspended in device mode by returning a positive value in
prepare() callback. This optimization only applies to devices without
pinctrl, as pinctrl has distinct logic tied to system suspend/resume.
Signed-off-by: Roy Luo <royluo@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250312223434.3071598-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although some Type-C DRD devices that do not support the DP Sink
function (such as Huawei Mate 40Pro), the Source Port initiates
Enter Mode CMD, but the device responds to Enter Mode ACK, the
Source port then initiates DP Status Update CMD, and the device
responds to DP Status Update NAK.
As PD2.0 spec ("6.4.4.3.4 Enter Mode Command")，A DR_Swap Message
Shall Not be sent during Modal Operation between the Port Partners.
At this time, the source port initiates DR_Swap message through the
"echo device > /sys/class/typec/port0/data_role" command to switch
the data role from host to device. The device will initiate a Hard
Reset for recovery, resulting in the failure of data role swap.
Therefore, when DP Status Update NAK is received, Exit Mode CMD is
initiated to exit the currently entered DP altmode.
Signed-off-by: Jos Wang <joswang@lenovo.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250209071926.69625-1-joswang1221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the typec connectors can have many muxes or switches for different
lanes (sbu, usb2, usb3) going into different modal states (usb2, usb3,
audio, debug) all of them will be called on typec_switch_set and
typec_mux_set. But not all of them will be handling the expected mode.
If one of the mux or switch will come back with EOPTNOSUPP this is no
reason to stop running through the next ones. Therefor we skip this
particular error value and continue calling the next.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-typec-mux-v1-1-22c0526381ba@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current xhci bus resume implementation prevents xHC host from generating
interrupts during high-speed USB 2 and super-speed USB 3 bus resume.
Only reason to disable interrupts during bus resume would be to prevent
the interrupt handler from interfering with the resume process of USB 2
ports.
Host initiated resume of USB 2 ports is done in two stages.
The xhci driver first transitions the port from 'U3' to 'Resume' state,
then wait in Resume for 20ms, and finally moves port to U0 state.
xhci driver can't prevent interrupts by keeping the xhci spinlock
due to this 20ms sleep.
Limit interrupt disabling to the USB 2 port resume case only.
resuming USB 2 ports in bus resume is only done in special cases where
USB 2 ports had to be forced to suspend during bus suspend.
The current way of preventing interrupts by clearing the 'Interrupt
Enable' (INTE) bit in USBCMD register won't prevent the Interrupter
registers 'Interrupt Pending' (IP), 'Event Handler Busy' (EHB) and
USBSTS register Event Interrupt (EINT) bits from being set.
New interrupts can't be issued before those bits are properly clered.
Disable interrupts by clearing the interrupter register 'Interrupt
Enable' (IE) bit instead. This way IP, EHB and INTE won't be set
before IE is enabled again and a new interrupt is triggered.
Reported-by: Devyn Liu <liudingyuan@huawei.com>
Closes: https://lore.kernel.org/linux-usb/b1a9e2d51b4d4ff7a304f77c5be8164e@huawei.com/
Cc: stable@vger.kernel.org
Tested-by: Devyn Liu <liudingyuan@huawei.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250410151828.2868740-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This check is performed before prepare_transfer() and prepare_ring(), so
enqueue can already point at the final link TRB of a segment. And indeed
it will, some 0.4% of times this code is called.
Then enqueue + 1 is an invalid pointer. It will crash the kernel right
away or load some junk which may look like a link TRB and cause the real
link TRB to be replaced with a NOOP. This wouldn't end well.
Use a functionally equivalent test which doesn't dereference the pointer
and always gives correct result.
Something has crashed my machine twice in recent days while playing with
an Etron HC, and a control transfer stress test ran for confirmation has
just crashed it again. The same test passes with this patch applied.
Fixes: 5e1c67abc9 ("xhci: Fix control transfer error on Etron xHCI host")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Link: https://lore.kernel.org/r/20250410151828.2868740-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A Short Packet event before the last TRB of a TD is followed by another
event on the final TRB on spec-compliant HCs, which is most of them.
A 'last_td_was_short' flag was added to know if a TD has just completed
as Short Packet and another event is to come. The flag was cleared after
seeing the event (unless no TDs are pending, but that's a separate bug)
or seeing a new TD complete as something other than Short Packet.
A rework replaced the flag with an 'old_trb_comp_code' variable. When
an event doesn't match the pending TD and the previous event was Short
Packet, the new event is silently ignored.
To preserve old behavior, 'old_trb_comp_code' should be cleared at this
point, but instead it is being set to current comp code, which is often
Short Packet again. This can cause more events to be silently ignored,
even though they are no longer connected with the old TD that completed
short and indicate a serious problem with the driver or the xHC.
Common device classes like UAC in async mode, UVC, serial or the UAS
status pipe complete as Short Packet routinely and could be affected.
Clear 'old_trb_comp_code' to zero, which is an invalid completion code
and the same value the variable starts with. This restores original
behavior on Short Packet and also works for illegal Etron events, which
the code has been extended to cover too.
Fixes: b331a3d809 ("xhci: Handle spurious events on Etron host isoc enpoints")
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250410151828.2868740-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce XHCI sideband, which manages the USB endpoints being requested by
a client driver. This is used for when client drivers are attempting to
offload USB endpoints to another entity for handling USB transfers. XHCI
sec intr will allow for drivers to fetch the required information about the
transfer ring, so the user can submit transfers independently. Expose the
required APIs for drivers to register and request for a USB endpoint and to
manage XHCI secondary interrupters.
Driver renaming, multiple ring segment page linking, proper endpoint clean
up, and allowing module compilation added by Wesley Cheng to complete
original concept code by Mathias Nyman.
Tested-by: Puma Hsu <pumahsu@google.com>
Tested-by: Daehwan Jung <dh10.jung@samsung.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Co-developed-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250409194804.3773260-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for
6.15-rc1. Included in here are:
- Thunderbolt driver and core api updates for new hardware and
features
- usb-storage const array cleanups
- typec driver updates
- dwc3 driver updates
- xhci driver updates and bugfixes
- small USB documentation updates
- usb cdns3 driver updates
- usb gadget driver updates
- other small driver updates and fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (92 commits)
thunderbolt: Do not add non-active NVM if NVM upgrade is disabled for retimer
thunderbolt: Scan retimers after device router has been enumerated
usb: host: cdns3: forward lost power information to xhci
usb: host: xhci-plat: allow upper layers to signal power loss
usb: xhci: change xhci_resume() parameters to explicit the desired info
usb: cdns3-ti: run HW init at resume() if HW was reset
usb: cdns3-ti: move reg writes to separate function
usb: cdns3: call cdns_power_is_lost() only once in cdns_resume()
usb: cdns3: rename hibernated argument of role->resume() to lost_power
usb: xhci: tegra: rename `runtime` boolean to `is_auto_runtime`
usb: host: xhci-plat: mvebu: use ->quirks instead of ->init_quirk() func
usb: dwc3: Don't use %pK through printk
usb: core: Don't use %pK through printk
usb: gadget: aspeed: Add NULL pointer check in ast_vhub_init_dev()
dt-bindings: usb: qcom,dwc3: Synchronize minItems for interrupts and -names
usb: common: usb-conn-gpio: switch psy_cfg from of_node to fwnode
usb: xhci: Avoid Stop Endpoint retry loop if the endpoint seems Running
usb: xhci: Don't change the status of stalled TDs on failed Stop EP
xhci: Avoid queuing redundant Stop Endpoint command for stalled endpoint
xhci: Handle spurious events on Etron host isoc enpoints
...
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (scsi_debug, ufs, lpfc, st, fnic, mpi3mr,
mpt3sas) and the removal of cxlflash.
The only non-trivial core change is an addition to unit attention
handling to recognize UAs for power on/reset and new media so the tape
driver can use it"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (107 commits)
scsi: st: Tighten the page format heuristics with MODE SELECT
scsi: st: ERASE does not change tape location
scsi: st: Fix array overflow in st_setup()
scsi: target: tcm_loop: Fix wrong abort tag
scsi: lpfc: Restore clearing of NLP_UNREG_INP in ndlp->nlp_flag
scsi: hisi_sas: Fixed failure to issue vendor specific commands
scsi: fnic: Remove unnecessary NUL-terminations
scsi: fnic: Remove redundant flush_workqueue() calls
scsi: core: Use a switch statement when attaching VPD pages
scsi: ufs: renesas: Add initialization code for R-Car S4-8 ES1.2
scsi: ufs: renesas: Add reusable functions
scsi: ufs: renesas: Refactor 0x10ad/0x10af PHY settings
scsi: ufs: renesas: Remove register control helper function
scsi: ufs: renesas: Add register read to remove save/set/restore
scsi: ufs: renesas: Replace init data by init code
scsi: ufs: dt-bindings: renesas,ufs: Add calibration data
scsi: mpi3mr: Task Abort EH Support
scsi: storvsc: Don't report the host packet status as the hv status
scsi: isci: Make most module parameters static
scsi: megaraid_sas: Make most module parameters static
...
Pull timer cleanups from Thomas Gleixner:
"A treewide hrtimer timer cleanup
hrtimers are initialized with hrtimer_init() and a subsequent store to
the callback pointer. This turned out to be suboptimal for the
upcoming Rust integration and is obviously a silly implementation to
begin with.
This cleanup replaces the hrtimer_init(T); T->function = cb; sequence
with hrtimer_setup(T, cb);
The conversion was done with Coccinelle and a few manual fixups.
Once the conversion has completely landed in mainline, hrtimer_init()
will be removed and the hrtimer::function becomes a private member"
* tag 'timers-cleanups-2025-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (100 commits)
wifi: rt2x00: Switch to use hrtimer_update_function()
io_uring: Use helper function hrtimer_update_function()
serial: xilinx_uartps: Use helper function hrtimer_update_function()
ASoC: fsl: imx-pcm-fiq: Switch to use hrtimer_setup()
RDMA: Switch to use hrtimer_setup()
virtio: mem: Switch to use hrtimer_setup()
drm/vmwgfx: Switch to use hrtimer_setup()
drm/xe/oa: Switch to use hrtimer_setup()
drm/vkms: Switch to use hrtimer_setup()
drm/msm: Switch to use hrtimer_setup()
drm/i915/request: Switch to use hrtimer_setup()
drm/i915/uncore: Switch to use hrtimer_setup()
drm/i915/pmu: Switch to use hrtimer_setup()
drm/i915/perf: Switch to use hrtimer_setup()
drm/i915/gvt: Switch to use hrtimer_setup()
drm/i915/huc: Switch to use hrtimer_setup()
drm/amdgpu: Switch to use hrtimer_setup()
stm class: heartbeat: Switch to use hrtimer_setup()
i2c: Switch to use hrtimer_setup()
iio: Switch to use hrtimer_setup()
...
Johan writes:
USB-serial update for 6.15-rc1
Here's a single USB-serial cleanup for 6.15-rc1 that's been sitting in
linux-next for a few weeks without any reported issues.
* tag 'usb-serial-6.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: mos7840: drop unused defines
cdns3-plat can know if power was lost across system-wide suspend.
Forward that information:
- Grab the lost_power bool from cdns_role_driver::resume(). Store it
into the power_lost field in struct xhci_plat_priv.
- xhci-plat will call xhci_resume() with that value (ORed to whether we
are in a hibernation restore).
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-9-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
