Provide a PSP implementation for netdevsim.
Use psp_dev_encapsulate() and psp_dev_rcv() to do actual encapsulation
and decapsulation on skbs, but perform no encryption or decryption. In
order to make encryption with a bad key result in a drop on the peer's
rx side, we stash our psd's generation number in the first byte of each
key before handing to the peer.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Co-developed-by: Daniel Zahka <daniel.zahka@gmail.com>
Signed-off-by: Daniel Zahka <daniel.zahka@gmail.com>
Link: https://patch.msgid.link/20250927225420.1443468-2-kuba@kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Software can only initialize the PIR and CIR of the command BD ring after
a FLR, and these two registers can only be set to 0. But the reset values
of these two registers are 0, so software does not need to update them.
If there is no a FLR and PIR and CIR are not 0, resetting them to 0 or
other values by software will cause the command BD ring to work
abnormally. This is because of an internal context in the ring prefetch
logic that will retain the state from the first incarnation of the ring
and continue prefetching from the stale location when the ring is
reinitialized. The internal context can only be reset by the FLR.
In addition, there is a logic error in the implementation, next_to_clean
indicates the software CIR and next_to_use indicates the software PIR.
But the current driver uses next_to_clean to set PIR and use next_to_use
to set CIR. This does not cause a problem in actual use, because the
current command BD ring is only initialized after FLR, and the initial
values of next_to_use and next_to_clean are both 0.
Therefore, this patch removes the initialization of PIR and CIR. Instead,
next_to_use and next_to_clean are initialized by reading the values of
PIR and CIR.
Fixes: 4701073c3d ("net: enetc: add initial netc-lib driver to support NTMP")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20250926013954.2003456-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The active-backup bonding mode supports XFRM ESP offload. However, when
a bond is added using command like `ip link add bond0 type bond mode 1
miimon 100`, the `ethtool -k` command shows that the XFRM ESP offload is
disabled. This occurs because, in bond_newlink(), we change bond link
first and register bond device later. So the XFRM feature update in
bond_option_mode_set() is not called as the bond device is not yet
registered, leading to the offload feature not being set successfully.
To resolve this issue, we can modify the code order in bond_newlink() to
ensure that the bond device is registered first before changing the bond
link parameters. This change will allow the XFRM ESP offload feature to be
correctly enabled.
Fixes: 007ab53455 ("bonding: fix feature flag setting at init time")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20250925023304.472186-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add sync reset timeout to stop poll_sync_reset in case there was no
reset done or abort event within timeout. Otherwise poll sync reset will
just continue and in case of fw fatal error no health reporting will be
done.
Fixes: 38b9f903f2 ("net/mlx5: Handle sync reset request event")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drori <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The reclaim_pages_cmd() function sends a command to the firmware to
reclaim pages if the command interface is active.
A race condition can occur if the command interface goes down (e.g., due
to a PCI error) while the mlx5_cmd_do() call is in flight. In this
case, mlx5_cmd_do() will return an error. The original code would
propagate this error immediately, bypassing the software-based page
reclamation logic that is supposed to run when the command interface is
down.
Fix this by checking whether mlx5_cmd_do() returns -ENXIO, which mark
that command interface is down. If this is the case, fall through to
the software reclamation path. If the command failed for any another
reason, or finished successfully, return as before.
Fixes: b898ce7bcc ("net/mlx5: cmdif, Avoid skipping reclaim pages if FW is not accessible")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stop polling on firmware response to command in polling mode if the
command interface got down. This situation can occur, for example, if a
firmware fatal error is detected during polling.
This change halts the polling process when the command interface goes
down, preventing unnecessary waits.
Fixes: b898ce7bcc ("net/mlx5: cmdif, Avoid skipping reclaim pages if FW is not accessible")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drori <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver did not handle failure of `netdev_alloc_skb_ip_align()`.
If the allocation failed, dereferencing `skb->protocol` could lead to
a NULL pointer dereference.
This patch tries to allocate `skb`. If the allocation fails, it falls
back to the normal path.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Tested-on: D-Link DGE-550T Rev-A3
Signed-off-by: Yeounsu Moon <yyyynoom@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250928190124.1156-1-yyyynoom@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In EC2 instances where the RSS hash key is not configurable, ethtool
shows bogus RSS hash key since ena_get_rxfh_key_size() unconditionally
returns ENA_HASH_KEY_SIZE.
Commit 6a4f7dc82d ("net: ena: rss: do not allocate key when not
supported") added proper handling for devices that don't support RSS
hash key configuration, but ena_get_rxfh_key_size() has been unchanged.
When the RSS hash key is not configurable, return 0 instead of
ENA_HASH_KEY_SIZE to clarify getting the value is not supported.
Tested on m5 instance families.
Without patch:
# ethtool -x ens5 | grep -A 1 "RSS hash key"
RSS hash key:
00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00
With patch:
# ethtool -x ens5 | grep -A 1 "RSS hash key"
RSS hash key:
Operation not supported
Fixes: 6a4f7dc82d ("net: ena: rss: do not allocate key when not supported")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Link: https://patch.msgid.link/20250929050247.51680-1-enjuk@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The nfp_net_get_rxfh_key_size() function returns -EOPNOTSUPP when
devices don't support RSS, and callers treat the negative value as a
large positive value since the return type is u32.
Return 0 when devices don't support RSS, aligning with the ethtool
interface .get_rxfh_key_size() that requires returning 0 in such cases.
Fixes: 9ff304bfaf ("nfp: add support for reporting CRC32 hash function")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Link: https://patch.msgid.link/20250929054230.68120-1-enjuk@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop the open-coded register polling routines.
Use readl_poll_timeout_atomic() in atomic state.
Also adjust the delay time to 10us which seems more reasonable.
Tested on NXP i.MX8MP and ROCKCHIP RK3588 boards,
the break condition was met right after the first polling,
no delay involved at all.
So the 10us delay should be long enough for most cases.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Link: https://patch.msgid.link/20250927081036.10611-1-0x1207@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For global RSS and multiple RSS scheme, the RSS type fields are defined
identically in the registers. So they can be defined as the macros
WX_RSS_FIELD_* to cleanup the codes. And to prepare for the RXFH support
in the next patch, move the rss_field to struct wx.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20250926023843.34340-3-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop those frames causing Head-of-Line Blocking due to Scheduling
(HLBS) error to avoid HLBS interrupt flooding and netdev watchdog
timeouts due to blocked packets. Tx queues can be configured to drop
those blocked packets by setting Drop Frames causing Scheduling Error
(DFBS) bit of EST_CONTROL register.
Also, add per queue HLBS drop count.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Reviewed-by: Matthew Gerlach <matthew.gerlach@altera.com>
Reviewed-by: Furong Xu <0x1207@gmail.com>
Link: https://patch.msgid.link/20250925-hlbs_2-v3-1-3b39472776c2@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull crypto library updates from Eric Biggers:
- Add a RISC-V optimized implementation of Poly1305. This code was
written by Andy Polyakov and contributed by Zhihang Shao.
- Migrate the MD5 code into lib/crypto/, and add KUnit tests for MD5.
Yes, it's still the 90s, and several kernel subsystems are still
using MD5 for legacy use cases. As long as that remains the case,
it's helpful to clean it up in the same way as I've been doing for
other algorithms.
Later, I plan to convert most of these users of MD5 to use the new
MD5 library API instead of the generic crypto API.
- Simplify the organization of the ChaCha, Poly1305, BLAKE2s, and
Curve25519 code.
Consolidate these into one module per algorithm, and centralize the
configuration and build process. This is the same reorganization that
has already been successful for SHA-1 and SHA-2.
- Remove the unused crypto_kpp API for Curve25519.
- Migrate the BLAKE2s and Curve25519 self-tests to KUnit.
- Always enable the architecture-optimized BLAKE2s code.
* tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux: (38 commits)
crypto: md5 - Implement export_core() and import_core()
wireguard: kconfig: simplify crypto kconfig selections
lib/crypto: tests: Enable Curve25519 test when CRYPTO_SELFTESTS
lib/crypto: curve25519: Consolidate into single module
lib/crypto: curve25519: Move a couple functions out-of-line
lib/crypto: tests: Add Curve25519 benchmark
lib/crypto: tests: Migrate Curve25519 self-test to KUnit
crypto: curve25519 - Remove unused kpp support
crypto: testmgr - Remove curve25519 kpp tests
crypto: x86/curve25519 - Remove unused kpp support
crypto: powerpc/curve25519 - Remove unused kpp support
crypto: arm/curve25519 - Remove unused kpp support
crypto: hisilicon/hpre - Remove unused curve25519 kpp support
lib/crypto: tests: Add KUnit tests for BLAKE2s
lib/crypto: blake2s: Consolidate into single C translation unit
lib/crypto: blake2s: Move generic code into blake2s.c
lib/crypto: blake2s: Always enable arch-optimized BLAKE2s code
lib/crypto: blake2s: Remove obsolete self-test
lib/crypto: x86/blake2s: Reduce size of BLAKE2S_SIGMA2
lib/crypto: chacha: Consolidate into single module
...
Add three counters to vnic health reporter:
bar_uar_access, odp_local_triggered_page_fault, and
odp_remote_triggered_page_fault.
- bar_uar_access
number of WRITE or READ access operations to the UAR on the PCIe
BAR.
- odp_local_triggered_page_fault
number of locally-triggered page-faults due to ODP.
- odp_remote_triggered_page_fault
number of remotly-triggered page-faults due to ODP.
Example access:
$ devlink health diagnose pci/0000:08:00.0 reporter vnic
vNIC env counters:
total_error_queues: 0 send_queue_priority_update_flow: 0
comp_eq_overrun: 0 async_eq_overrun: 0 cq_overrun: 0
invalid_command: 0 quota_exceeded_command: 0
nic_receive_steering_discard: 0 icm_consumption: 1032
bar_uar_access: 1279 odp_local_triggered_page_fault: 20
odp_remote_triggered_page_fault: 34
Signed-off-by: Akiva Goldberger <agoldberger@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1758797130-829564-1-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bp->dev->dev_addr is of type `unsigned char *`. Casting it to a u32
pointer and dereferencing implies dealing manually with endianness,
which is error-prone.
Replace by calls to get_unaligned_le32|le16() helpers.
This was found using sparse:
⟩ make C=2 drivers/net/ethernet/cadence/macb_main.o
warning: incorrect type in assignment (different base types)
expected unsigned int [usertype] bottom
got restricted __le32 [usertype]
warning: incorrect type in assignment (different base types)
expected unsigned short [usertype] top
got restricted __le16 [usertype]
...
Reviewed-by: Sean Anderson <sean.anderson@linux.dev>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250923-macb-fixes-v6-5-772d655cdeb6@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move from 2*NUM_QUEUES dma_alloc_coherent() for DMA descriptor rings to
2 calls overall.
Issue is with how all queues share the same register for configuring the
upper 32-bits of Tx/Rx descriptor rings. Taking Tx, notice how TBQPH
does *not* depend on the queue index:
#define GEM_TBQP(hw_q) (0x0440 + ((hw_q) << 2))
#define GEM_TBQPH(hw_q) (0x04C8)
queue_writel(queue, TBQP, lower_32_bits(queue->tx_ring_dma));
#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
if (bp->hw_dma_cap & HW_DMA_CAP_64B)
queue_writel(queue, TBQPH, upper_32_bits(queue->tx_ring_dma));
#endif
To maximise our chances of getting valid DMA addresses, we do a single
dma_alloc_coherent() across queues. This improves the odds because
alloc_pages() guarantees natural alignment. Other codepaths (IOMMU or
dev/arch dma_map_ops) don't give high enough guarantees
(even page-aligned isn't enough).
Two consideration:
- dma_alloc_coherent() gives us page alignment. Here we remove this
constraint meaning each queue's ring won't be page-aligned anymore.
- This can save some tiny amounts of memory. Fewer allocations means
(1) less overhead (constant cost per alloc) and (2) less wasted bytes
due to alignment constraints.
Example for (2): 4 queues, default ring size (512), 64-bit DMA
descriptors, 16K pages:
- Before: 8 allocs of 8K, each rounded to 16K => 64K wasted.
- After: 2 allocs of 32K => 0K wasted.
Fixes: 02c958dd34 ("net/macb: add TX multiqueue support for gem")
Reviewed-by: Sean Anderson <sean.anderson@linux.dev>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com> # on sam9x75
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250923-macb-fixes-v6-4-772d655cdeb6@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The tx/rx ring size calculation is somewhat complex and partially hidden
behind a macro. Move that out of the {RX,TX}_RING_BYTES() macros and
macb_{alloc,free}_consistent() functions into neat separate functions.
In macb_free_consistent(), we drop the size variable and directly call
the size helpers in the arguments list. In macb_alloc_consistent(), we
keep the size variable that is used by netdev_dbg() calls.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250923-macb-fixes-v6-3-772d655cdeb6@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MACB driver acts as if TBQPH/RBQPH are configurable on a per queue
basis; this is a lie. A single register configures the upper 32 bits of
each DMA descriptor buffers for all queues.
Concrete actions:
- Drop GEM_TBQPH/GEM_RBQPH macros which have a queue index argument.
Only use MACB_TBQPH/MACB_RBQPH constants.
- Drop struct macb_queue->TBQPH/RBQPH fields.
- In macb_init_buffers(): do a single write to TBQPH and RBQPH for all
queues instead of a write per queue.
- In macb_tx_error_task(): drop the write to TBQPH.
- In macb_alloc_consistent(): if allocations give different upper
32-bits, fail. Previously, it would have lead to silent memory
corruption as queues would have used the upper 32 bits of the alloc
from queue 0 and their own low 32 bits.
- In macb_suspend(): if we use the tie off descriptor for suspend, do
the write once for all queues instead of once per queue.
Fixes: fff8019a08 ("net: macb: Add 64 bit addressing support for GEM")
Fixes: ae1f2a56d2 ("net: macb: Added support for many RX queues")
Reviewed-by: Sean Anderson <sean.anderson@linux.dev>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250923-macb-fixes-v6-2-772d655cdeb6@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The blamed commit introduced the function lanphy_modify_page_reg which
as name suggests it, it modifies the registers. In the same commit we
have started to use this function inside the drivers. The problem is
that in the function lan8814_config_init we passed the wrong page number
when disabling the aneg towards host side. We passed extended page number
4(LAN8814_PAGE_COMMON_REGS) instead of extended page
5(LAN8814_PAGE_PORT_REGS)
Fixes: a0de636ed7 ("net: phy: micrel: Introduce lanphy_modify_page_reg")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250925064702.3906950-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce a NPU callback to initialize flow stats and remove NPU stats
initialization from airoha_npu_get routine. Add num_stats_entries to
airoha_npu_ppe_stats_setup routine.
This patch makes the code more readable since NPU statistic are now
initialized on demand by the NPU consumer (at the moment NPU statistic
are configured just by the airoha_eth driver).
Moreover this patch allows the NPU consumer (PPE module) to explicitly
enable/disable NPU flow stats.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250924-airoha-npu-init-stats-callback-v1-1-88bdf3c941b2@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
list_first_entry() never returns NULL — if the list is empty, it still
returns a pointer to an invalid object, leading to potential invalid
memory access when dereferenced.
The calls to list_first_entry() are always guarded by !list_empty(),
which guarantees a valid entry is returned. Therefore, the additional
`if (!p_buffer) break;` checks in qed_ooo_release_connection_isles(),
qed_ooo_release_all_isles(), and qed_ooo_free() are redundant and
unreachable.
Remove the dead code for clarity and consistency with common list
handling patterns in the kernel. No functional change intended.
Signed-off-by: Zhen Ni <zhen.ni@easystack.cn>
Link: https://patch.msgid.link/20250924030219.1252773-1-zhen.ni@easystack.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
idpf: add XSk support
Alexander Lobakin says:
Add support for XSk xmit and receive using libeth_xdp.
This includes adding interfaces to reconfigure/enable/disable only
a particular set of queues and support for checksum offload XSk Tx
metadata.
libeth_xdp's implementation mostly matches the one of ice: batched
allocations and sending, unrolled descriptor writes etc. But unlike
other Intel drivers, XSk wakeup is implemented using CSD/IPI instead
of HW "software interrupt". In lots of different tests, this yielded
way better perf than SW interrupts, but also, this gives better
control over which CPU will handle the NAPI loop (SW interrupts are
a subject to irqbalance and stuff, while CSDs are strictly pinned
1:1 to the core of the same index).
Note that the header split is always disabled for XSk queues, as
for now we see no reasons to have it there.
XSk xmit perf is up to 3x comparing to ice. XSk XDP_PASS is also
faster a bunch as it uses system percpu page_pools, so that the
only overhead left is memcpy(). The rest is at least comparable.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
idpf: enable XSk features and ndo_xsk_wakeup
idpf: implement Rx path for AF_XDP
idpf: implement XSk xmit
idpf: add XSk pool initialization
idpf: add virtchnl functions to manage selected queues
====================
Link: https://patch.msgid.link/20250924175230.1290529-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
syzbot reported WARNING in rtl8150_start_xmit/usb_submit_urb.
This is the sequence of events that leads to the warning:
rtl8150_start_xmit() {
netif_stop_queue();
usb_submit_urb(dev->tx_urb);
}
rtl8150_set_multicast() {
netif_stop_queue();
netif_wake_queue(); <-- wakes up TX queue before URB is done
}
rtl8150_start_xmit() {
netif_stop_queue();
usb_submit_urb(dev->tx_urb); <-- double submission
}
rtl8150_set_multicast being the ndo_set_rx_mode callback should not be
calling netif_stop_queue and notif_start_queue as these handle
TX queue synchronization.
The net core function dev_set_rx_mode handles the synchronization
for rtl8150_set_multicast making it safe to remove these locks.
Reported-and-tested-by: syzbot+78cae3f37c62ad092caa@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=78cae3f37c62ad092caa
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: I Viswanath <viswanathiyyappan@gmail.com>
Link: https://patch.msgid.link/20250924134350.264597-1-viswanathiyyappan@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
pull-request: can-next 2025-09-25
this is a pull request of 48 patches for net-next/main, which
supersedes tags/linux-can-next-for-6.18-20250923.
The 1st patch is by Xichao Zhao and converts ns_to_ktime() to
us_to_ktime() in the m_can driver.
Vincent Mailhol contributes 2 patches: Updating the MAINTAINERS and
mailmap files to Vincent's new email address and sorting the includes
in the CAN helper library alphabeticaly.
Stéphane Grosjean's patch modifies all peak CAN drivers and the
mailmap to reflect Stéphane's new email address.
4 patches by Biju Das update the CAN-FD handling in the rcar_canfd
driver.
Followed by 11 patches by Geert Uytterhoeven updating and improving
the rcar_can driver.
Stefan Mätje contributes 2 patches for the esd_usb driver updating the
error messages.
The next 3 patch series are all by Vincent Mailhol: 3 patches to
optimize the size of struct raw_sock and struct uniqframe. 4 patches
which rework the CAN MTU logic as preparation for CAN-XL interfaces.
And finally 20 patches that prepare and refactor the CAN netlink code
for the upcoming CAN-XL support.
* tag 'linux-can-next-for-6.18-20250924' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: (48 commits)
can: netlink: add userland error messages
can: dev: add can_get_ctrlmode_str()
can: calc_bittiming: make can_calc_tdco() FD agnostic
can: netlink: make can_tdc_fill_info() FD agnostic
can: netlink: add can_bitrate_const_fill_info()
can: netlink: add can_bittiming_const_fill_info()
can: netlink: add can_bittiming_fill_info()
can: netlink: add can_data_bittiming_get_size()
can: netlink: make can_tdc_get_size() FD agnostic
can: netlink: add can_ctrlmode_changelink()
can: netlink: add can_dtb_changelink()
can: netlink: make can_tdc_changelink() FD agnostic
can: netlink: remove useless check in can_tdc_changelink()
can: netlink: refactor CAN_CTRLMODE_TDC_{AUTO,MANUAL} flag reset logic
can: netlink: add can_validate_databittiming()
can: netlink: add can_validate_tdc()
can: netlink: refactor can_validate_bittiming()
can: netlink: document which symbols are FD specific
can: dev: make can_get_relative_tdco() FD agnostic and move it to bittiming.h
can: dev: move struct data_bittiming_params to linux/can/bittiming.h
...
====================
Link: https://patch.msgid.link/20250925121332.848157-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Johannes Berg says:
====================
Quite a bit more things, including pull requests from drivers:
- mt76: MLO support, HW restart improvements
- rtw88/89: small features, prep for RTL8922DE support
- ath10k: GTK rekey fixes
- cfg80211/mac80211:
- additions for more NAN support
- S1G channel representation cleanup
* tag 'wireless-next-2025-09-25' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (167 commits)
wifi: libertas: add WQ_UNBOUND to alloc_workqueue users
Revert "wifi: libertas: WQ_PERCPU added to alloc_workqueue users"
wifi: libertas: WQ_PERCPU added to alloc_workqueue users
wifi: cfg80211: fix width unit in cfg80211_radio_chandef_valid()
wifi: ath11k: HAL SRNG: don't deinitialize and re-initialize again
wifi: ath12k: enforce CPU endian format for all QMI data
wifi: ath12k: Use 1KB Cache Flush Command for QoS TID Descriptors
wifi: ath12k: Fix flush cache failure during RX queue update
wifi: ath12k: Add Retry Mechanism for REO RX Queue Update Failures
wifi: ath12k: Refactor REO command to use ath12k_dp_rx_tid_rxq
wifi: ath12k: Refactor RX TID buffer cleanup into helper function
wifi: ath12k: Refactor RX TID deletion handling into helper function
wifi: ath12k: Increase DP_REO_CMD_RING_SIZE to 256
wifi: cfg80211: remove IEEE80211_CHAN_{1,2,4,8,16}MHZ flags
wifi: rtw89: avoid circular locking dependency in ser_state_run()
wifi: rtw89: fix leak in rtw89_core_send_nullfunc()
wifi: rtw89: avoid possible TX wait initialization race
wifi: rtw89: fix use-after-free in rtw89_core_tx_kick_off_and_wait()
wifi: ath12k: Fix peer lookup in ath12k_dp_mon_rx_deliver_msdu()
wifi: mac80211: fix Rx packet handling when pubsta information is not available
...
====================
Link: https://patch.msgid.link/20250925232341.4544-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
