One of the factors of a link's grade is the channel load, which is
calculated from the AP's bss load element.
The current code takes this element from the beacon for an active link,
and from bss->ies for an inactive link.
bss->ies is set to either the beacon's ies or to the probe response
ones, with preference to the probe response (meaning that if there was
even one probe response, the ies of it will be stored in bss->ies and
won't be overiden by the beacon ies).
The probe response can be very old, i.e. from the connection time,
where a beacon is updated before each link selection (which is
triggered only after a passive scan).
In such case, the bss load element in the probe response will not
include the channel load caused by the STA, where the beacon will.
This will cause the inactive link to always have a lower channel
load, and therefore an higher grade than the active link's one.
This causes repeated link switches, causing the throughput to drop.
Fix this by always taking the ies from the beacon, as those are for
sure new.
Fixes: d1e879ec60 ("wifi: iwlwifi: add iwlmld sub-driver")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20251110145652.b493dbb1853a.I058ba7309c84159f640cc9682d1bda56dd56a536@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
The list_for_each_entry() iterator must not be used outside the loop.
Even though we break and check for NULL, doing so still violates kernel
iteration rules and triggers Coccinelle's use_after_iter.cocci warning.
Cache the matched entry in aux_roc_te and use it consistently after the
loop. This follows iterator best practices, resolves the warning, and
makes the code more maintainable.
Signed-off-by: Junjie Cao <junjie.cao@intel.com>
Link: https://patch.msgid.link/20251016014919.383565-1-junjie.cao@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Some Marvell AP firmware used with mwl8k misbehaves when beacon frames
do not contain a WLAN_EID_DS_PARAMS element with the current channel.
It was reported on OpenWrt Github issues [0].
When hostapd/mac80211 omits DSSS Parameter Set from the beacon (which is
valid on some bands), the firmware stops transmitting sane frames and RX
status starts reporting bogus channel information. This makes AP mode
unusable.
Newer Marvell drivers (mwlwifi [1]) hard-code DSSS Parameter Set into
AP beacons for all chips, which suggests this is a firmware requirement
rather than a mwl8k-specific quirk.
Mirror that behaviour in mwl8k: when setting the beacon, check if
WLAN_EID_DS_PARAMS is present, and if not, extend the beacon and inject
a DSSS Parameter Set element, using the current channel from
hw->conf.chandef.chan.
Tested on Linksys EA4500 (88W8366).
[0] https://github.com/openwrt/openwrt/issues/19088
[1] db97edf20f/hif/fwcmd.c (L675)
Fixes: b64fe619e3 ("mwl8k: basic AP interface support")
Tested-by: Antony Kolitsos <zeusomighty@hotmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://patch.msgid.link/20251111100733.2825970-3-paweldembicki@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When reporting tx completion using ieee80211_tx_status_xxx() family of
functions, the status part of the struct ieee80211_tx_info nested in the
skb is used to report things like transmit rates & retry count to mac80211
On the TX data path, this is correctly memset to 0 before calling
ieee80211_tx_status_ext(), but on the tx mgmt path this was not done.
This leads to mac80211 treating garbage values as valid transmit counters
(like tx retries for example) and accounting them as real statistics that
makes their way to userland via station dump.
The same issue was resolved in ath12k by commit 9903c0986f ("wifi:
ath12k: Add memset and update default rate value in wmi tx completion")
Tested-on: QCN9074 PCI WLAN.HK.2.9.0.1-01977-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20251104083957.717825-1-nico.escande@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Jeff Johnson says:
==================
ath.git update for v6.18-rc5
Revert an ath12k change which resulted in a significance performance
impact on WCN7850.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
hwsim radios marked destroy_on_close are removed when the Netlink socket
that created them is closed. As the portid is not unique across network
namespaces, closing a socket in one namespace may remove radios in another
if it has the destroy_on_close flag set.
Instead of matching the network namespace, match the netgroup of the radio
to limit radio removal to those that have been created by the closing
Netlink socket. The netgroup of a radio identifies the network namespace
it was created in, and matching on it removes a destroy_on_close radio
even if it has been moved to another namespace.
Fixes: 100cb9ff40 ("mac80211_hwsim: Allow managing radios from non-initial namespaces")
Signed-off-by: Martin Willi <martin@strongswan.org>
Link: https://patch.msgid.link/20251103082436.30483-1-martin@strongswan.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, whenever there is a need to transmit an Action frame,
the brcmfmac driver always uses the P2P vif to send the "actframe" IOVAR to
firmware. The P2P interfaces were available when wpa_supplicant is managing
the wlan interface.
However, the P2P interfaces are not created/initialized when only hostapd
is managing the wlan interface. And if hostapd receives an ANQP Query REQ
Action frame even from an un-associated STA, the brcmfmac driver tries
to use an uninitialized P2P vif pointer for sending the IOVAR to firmware.
This NULL pointer dereferencing triggers a driver crash.
[ 1417.074538] Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000000
[...]
[ 1417.075188] Hardware name: Raspberry Pi 4 Model B Rev 1.5 (DT)
[...]
[ 1417.075653] Call trace:
[ 1417.075662] brcmf_p2p_send_action_frame+0x23c/0xc58 [brcmfmac]
[ 1417.075738] brcmf_cfg80211_mgmt_tx+0x304/0x5c0 [brcmfmac]
[ 1417.075810] cfg80211_mlme_mgmt_tx+0x1b0/0x428 [cfg80211]
[ 1417.076067] nl80211_tx_mgmt+0x238/0x388 [cfg80211]
[ 1417.076281] genl_family_rcv_msg_doit+0xe0/0x158
[ 1417.076302] genl_rcv_msg+0x220/0x2a0
[ 1417.076317] netlink_rcv_skb+0x68/0x140
[ 1417.076330] genl_rcv+0x40/0x60
[ 1417.076343] netlink_unicast+0x330/0x3b8
[ 1417.076357] netlink_sendmsg+0x19c/0x3f8
[ 1417.076370] __sock_sendmsg+0x64/0xc0
[ 1417.076391] ____sys_sendmsg+0x268/0x2a0
[ 1417.076408] ___sys_sendmsg+0xb8/0x118
[ 1417.076427] __sys_sendmsg+0x90/0xf8
[ 1417.076445] __arm64_sys_sendmsg+0x2c/0x40
[ 1417.076465] invoke_syscall+0x50/0x120
[ 1417.076486] el0_svc_common.constprop.0+0x48/0xf0
[ 1417.076506] do_el0_svc+0x24/0x38
[ 1417.076525] el0_svc+0x30/0x100
[ 1417.076548] el0t_64_sync_handler+0x100/0x130
[ 1417.076569] el0t_64_sync+0x190/0x198
[ 1417.076589] Code: f9401e80 aa1603e2 f9403be1 5280e483 (f9400000)
Fix this, by always using the vif corresponding to the wdev on which the
Action frame Transmission request was initiated by the userspace. This way,
even if P2P vif is not available, the IOVAR is sent to firmware on AP vif
and the ANQP Query RESP Action frame is transmitted without crashing the
driver.
Move init_completion() for "send_af_done" from brcmf_p2p_create_p2pdev()
to brcmf_p2p_attach(). Because the former function would not get executed
when only hostapd is managing wlan interface, and it is not safe to do
reinit_completion() later in brcmf_p2p_tx_action_frame(), without any prior
init_completion().
And in the brcmf_p2p_tx_action_frame() function, the condition check for
P2P Presence response frame is not needed, since the wpa_supplicant is
properly sending the P2P Presense Response frame on the P2P-GO vif instead
of the P2P-Device vif.
Cc: stable@vger.kernel.org
Fixes: 18e2f61db3 ("brcmfmac: P2P action frame tx")
Signed-off-by: Gokul Sivakumar <gokulkumar.sivakumar@infineon.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20251013102819.9727-1-gokulkumar.sivakumar@infineon.com
[Cc stable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jeff Johnson says:
==================
ath.git update for v6.18-rc1
Fix memory leaks in both ath10k and ath12k.
Fix a sparse issue in ath11k.
Allow ath11k suspend/resume to work on more Lenovo laptops.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bitwise operations with WMI_KEY_PAIRWISE (defined as 0) are ineffective
and misleading. This results in pairwise key validations added in
commit 97acb0259c ("wifi: ath11k: fix group data packet drops
during rekey") to always evaluate false and clear key commands for
pairwise keys are not honored.
Since firmware supports overwriting the new key without explicitly
clearing the previous one, there is no visible impact currently.
However, to restore consistency with the previous behavior and improve
clarity, replace bitwise operations with direct assignments and
comparisons for key flags.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.9.0.1-02146-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-wireless/aLlaetkalDvWcB7b@stanley.mountain
Fixes: 97acb0259c ("wifi: ath11k: fix group data packet drops during rekey")
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20251003092158.1080637-1-rameshkumar.sundaram@oss.qualcomm.com
[update copyright per current guidance]
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k just like ath11k [1] did not handle skb cleanup during idr
cleanup callback. Both ath12k_mac_vif_txmgmt_idr_remove() and
ath12k_mac_tx_mgmt_pending_free() performed idr cleanup and DMA
unmapping for skb but only ath12k_mac_tx_mgmt_pending_free() freed
skb. As a result, during vdev deletion a memory leak occurs.
Refactor all clean up steps into a new function. New function
ath12k_mac_tx_mgmt_free() creates a centralized area where idr
cleanup, DMA unmapping for skb and freeing skb is performed. Utilize
skb pointer given by idr_remove(), instead of passed as a function
argument because IDR will be protected by locking. This will prevent
concurrent modification of the same IDR.
Now ath12k_mac_tx_mgmt_pending_free() and
ath12k_mac_vif_txmgmt_idr_remove() call ath12k_mac_tx_mgmt_free().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Link: https://lore.kernel.org/r/1637832614-13831-1-git-send-email-quic_srirrama@quicinc.com > # [1]
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Karthik M <quic_karm@quicinc.com>
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250923220316.1595758-1-muna.sinada@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Pull networking updates from Paolo Abeni:
"Core & protocols:
- Improve drop account scalability on NUMA hosts for RAW and UDP
sockets and the backlog, almost doubling the Pps capacity under DoS
- Optimize the UDP RX performance under stress, reducing contention,
revisiting the binary layout of the involved data structs and
implementing NUMA-aware locking. This improves UDP RX performance
by an additional 50%, even more under extreme conditions
- Add support for PSP encryption of TCP connections; this mechanism
has some similarities with IPsec and TLS, but offers superior HW
offloads capabilities
- Ongoing work to support Accurate ECN for TCP. AccECN allows more
than one congestion notification signal per RTT and is a building
block for Low Latency, Low Loss, and Scalable Throughput (L4S)
- Reorganize the TCP socket binary layout for data locality, reducing
the number of touched cachelines in the fastpath
- Refactor skb deferral free to better scale on large multi-NUMA
hosts, this improves TCP and UDP RX performances significantly on
such HW
- Increase the default socket memory buffer limits from 256K to 4M to
better fit modern link speeds
- Improve handling of setups with a large number of nexthop, making
dump operating scaling linearly and avoiding unneeded
synchronize_rcu() on delete
- Improve bridge handling of VLAN FDB, storing a single entry per
bridge instead of one entry per port; this makes the dump order of
magnitude faster on large switches
- Restore IP ID correctly for encapsulated packets at GSO
segmentation time, allowing GRO to merge packets in more scenarios
- Improve netfilter matching performance on large sets
- Improve MPTCP receive path performance by leveraging recently
introduced core infrastructure (skb deferral free) and adopting
recent TCP autotuning changes
- Allow bridges to redirect to a backup port when the bridge port is
administratively down
- Introduce MPTCP 'laminar' endpoint that con be used only once per
connection and simplify common MPTCP setups
- Add RCU safety to dst->dev, closing a lot of possible races
- A significant crypto library API for SCTP, MPTCP and IPv6 SR,
reducing code duplication
- Supports pulling data from an skb frag into the linear area of an
XDP buffer
Things we sprinkled into general kernel code:
- Generate netlink documentation from YAML using an integrated YAML
parser
Driver API:
- Support using IPv6 Flow Label in Rx hash computation and RSS queue
selection
- Introduce API for fetching the DMA device for a given queue,
allowing TCP zerocopy RX on more H/W setups
- Make XDP helpers compatible with unreadable memory, allowing more
easily building DevMem-enabled drivers with a unified XDP/skbs
datapath
- Add a new dedicated ethtool callback enabling drivers to provide
the number of RX rings directly, improving efficiency and clarity
in RX ring queries and RSS configuration
- Introduce a burst period for the health reporter, allowing better
handling of multiple errors due to the same root cause
- Support for DPLL phase offset exponential moving average,
controlling the average smoothing factor
Device drivers:
- Add a new Huawei driver for 3rd gen NIC (hinic3)
- Add a new SpacemiT driver for K1 ethernet MAC
- Add a generic abstraction for shared memory communication
devices (dibps)
- Ethernet high-speed NICs:
- nVidia/Mellanox:
- Use multiple per-queue doorbell, to avoid MMIO contention
issues
- support adjacent functions, allowing them to delegate their
SR-IOV VFs to sibling PFs
- support RSS for IPSec offload
- support exposing raw cycle counters in PTP and mlx5
- support for disabling host PFs.
- Intel (100G, ice, idpf):
- ice: support for SRIOV VFs over an Active-Active link
aggregate
- ice: support for firmware logging via debugfs
- ice: support for Earliest TxTime First (ETF) hardware offload
- idpf: support basic XDP functionalities and XSk
- Broadcom (bnxt):
- support Hyper-V VF ID
- dynamic SRIOV resource allocations for RoCE
- Meta (fbnic):
- support queue API, zero-copy Rx and Tx
- support basic XDP functionalities
- devlink health support for FW crashes and OTP mem corruptions
- expand hardware stats coverage to FEC, PHY, and Pause
- Wangxun:
- support ethtool coalesce options
- support for multiple RSS contexts
- Ethernet virtual:
- Macsec:
- replace custom netlink attribute checks with policy-level
checks
- Bonding:
- support aggregator selection based on port priority
- Microsoft vNIC:
- use page pool fragments for RX buffers instead of full pages
to improve memory efficiency
- Ethernet NICs consumer, and embedded:
- Qualcomm: support Ethernet function for IPQ9574 SoC
- Airoha: implement wlan offloading via NPU
- Freescale
- enetc: add NETC timer PTP driver and add PTP support
- fec: enable the Jumbo frame support for i.MX8QM
- Renesas (R-Car S4):
- support HW offloading for layer 2 switching
- support for RZ/{T2H, N2H} SoCs
- Cadence (macb): support TAPRIO traffic scheduling
- TI:
- support for Gigabit ICSS ethernet SoC (icssm-prueth)
- Synopsys (stmmac): a lot of cleanups
- Ethernet PHYs:
- Support 10g-qxgmi phy-mode for AQR412C, Felix DSA and Lynx PCS
driver
- Support bcm63268 GPHY power control
- Support for Micrel lan8842 PHY and PTP
- Support for Aquantia AQR412 and AQR115
- CAN:
- a large CAN-XL preparation work
- reorganize raw_sock and uniqframe struct to minimize memory
usage
- rcar_canfd: update the CAN-FD handling
- WiFi:
- extended Neighbor Awareness Networking (NAN) support
- S1G channel representation cleanup
- improve S1G support
- WiFi drivers:
- Intel (iwlwifi):
- major refactor and cleanup
- Broadcom (brcm80211):
- support for AP isolation
- RealTek (rtw88/89) rtw88/89:
- preparation work for RTL8922DE support
- MediaTek (mt76):
- HW restart improvements
- MLO support
- Qualcomm/Atheros (ath10k):
- GTK rekey fixes
- Bluetooth drivers:
- btusb: support for several new IDs for MT7925
- btintel: support for BlazarIW core
- btintel_pcie: support for _suspend() / _resume()
- btintel_pcie: support for Scorpious, Panther Lake-H484 IDs"
* tag 'net-next-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1536 commits)
net: stmmac: Add support for Allwinner A523 GMAC200
dt-bindings: net: sun8i-emac: Add A523 GMAC200 compatible
Revert "Documentation: net: add flow control guide and document ethtool API"
octeontx2-pf: fix bitmap leak
octeontx2-vf: fix bitmap leak
net/mlx5e: Use extack in set rxfh callback
net/mlx5e: Introduce mlx5e_rss_params for RSS configuration
net/mlx5e: Introduce mlx5e_rss_init_params
net/mlx5e: Remove unused mdev param from RSS indir init
net/mlx5: Improve QoS error messages with actual depth values
net/mlx5e: Prevent entering switchdev mode with inconsistent netns
net/mlx5: HWS, Generalize complex matchers
net/mlx5: Improve write-combining test reliability for ARM64 Grace CPUs
selftests/net: add tcp_port_share to .gitignore
Revert "net/mlx5e: Update and set Xon/Xoff upon MTU set"
net: add NUMA awareness to skb_attempt_defer_free()
net: use llist for sd->defer_list
net: make softnet_data.defer_count an atomic
selftests: drv-net: psp: add tests for destroying devices
selftests: drv-net: psp: add test for auto-adjusting TCP MSS
...
Pull SoC driver updates from Arnd Bergmann:
"Lots of platform specific updates for Qualcomm SoCs, including a new
TEE subsystem driver for the Qualcomm QTEE firmware interface.
Added support for the Apple A11 SoC in drivers that are shared with
the M1/M2 series, among more updates for those.
Smaller platform specific driver updates for Renesas, ASpeed,
Broadcom, Nvidia, Mediatek, Amlogic, TI, Allwinner, and Freescale
SoCs.
Driver updates in the cache controller, memory controller and reset
controller subsystems.
SCMI firmware updates to add more features and improve robustness.
This includes support for having multiple SCMI providers in a single
system.
TEE subsystem support for protected DMA-bufs, allowing hardware to
access memory areas that managed by the kernel but remain inaccessible
from the CPU in EL1/EL0"
* tag 'soc-drivers-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (139 commits)
soc/fsl/qbman: Use for_each_online_cpu() instead of for_each_cpu()
soc: fsl: qe: Drop legacy-of-mm-gpiochip.h header from GPIO driver
soc: fsl: qe: Change GPIO driver to a proper platform driver
tee: fix register_shm_helper()
pmdomain: apple: Add "apple,t8103-pmgr-pwrstate"
dt-bindings: spmi: Add Apple A11 and T2 compatible
serial: qcom-geni: Load UART qup Firmware from linux side
spi: geni-qcom: Load spi qup Firmware from linux side
i2c: qcom-geni: Load i2c qup Firmware from linux side
soc: qcom: geni-se: Add support to load QUP SE Firmware via Linux subsystem
soc: qcom: geni-se: Cleanup register defines and update copyright
dt-bindings: qcom: se-common: Add QUP Peripheral-specific properties for I2C, SPI, and SERIAL bus
Documentation: tee: Add Qualcomm TEE driver
tee: qcom: enable TEE_IOC_SHM_ALLOC ioctl
tee: qcom: add primordial object
tee: add Qualcomm TEE driver
tee: increase TEE_MAX_ARG_SIZE to 4096
tee: add TEE_IOCTL_PARAM_ATTR_TYPE_OBJREF
tee: add TEE_IOCTL_PARAM_ATTR_TYPE_UBUF
tee: add close_context to TEE driver operation
...
Currently if a user enqueues a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() uses
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistency cannot be addressed without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
Explicitly add the WQ_UNBOUND flag to alloc_workqueue() users, marking
the workqueue unbound.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20250923145905.327269-2-marco.crivellari@suse.com
[use imperative voice in subject, fix typos]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 1e06a13751 ("wifi: libertas: WQ_PERCPU added
to alloc_workqueue users") since there's really no reason to use
per-CPU here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This change add a new WQ_PERCPU flag, to explicitly request the use of
the per-CPU behavior. Both flags coexist for one release cycle to allow
callers to transition their calls.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
All existing users have been updated accordingly.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20250922102407.186660-2-marco.crivellari@suse.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jeff Johnson says:
==================
ath.git patches for v6.18
Highlights for some specific drivers include:
ath10k:
Fix connection after GTK rekeying
ath12k:
Fix Issues in REO RX Queue Updates
Handle inactivity STA kickout event
And of course there is the usual set of cleanups and bug fixes across
the entire family of "ath" drivers.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the QMI interface only works on little endian systems due to how
it encodes and decodes data. Most QMI related data structures do not use
endian specific types and are already defined in CPU native order. The
ath12k specific QMI structs are an exception: they use partially endian
specific types, which prevents the QMI interface from being extended to
support big endian systems.
Update the two affected ath12k QMI structs to use CPU order types instead.
This is required because the QMI interface is being extended to support big
endian system, and that support depends on QMI data structures being
defined in CPU native order.
This change:
* preserves compatibility with existing kernels, which only support little
endian system
* enables future support for big endian systems
* aligns ath12k QMI handling with the general QMI design
Signed-off-by: Alexander Wilhelm <alexander.wilhelm@westermo.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250922061607.11543-1-alexander.wilhelm@westermo.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During stress test scenarios, when the REO command ring becomes full,
the RX queue update command issued during peer deletion fails due to
insufficient space. In response, the host performs a dma_unmap and
frees the associated memory. However, the hardware still retains a
reference to the same memory address. If the kernel later reallocates
this address, unaware that the hardware is still using it, it can
lead to memory corruption-since the host might access or modify
memory that is still actively referenced by the hardware.
Implement a retry mechanism for the HAL_REO_CMD_UPDATE_RX_QUEUE
command during TID deletion to prevent memory corruption. Introduce
a new list, reo_cmd_update_rx_queue_list, in the struct ath12k_dp to
track pending RX queue updates. Protect this list with
reo_rxq_flush_lock, which also ensures synchronized access to
reo_cmd_cache_flush_list. Defer memory release until hardware
confirms the virtual address is no longer in use, avoiding immediate
deallocation on command failure. Release memory for pending RX queue
updates via ath12k_dp_rx_reo_cmd_list_cleanup() on system reset
if hardware confirmation is not received.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Manish Dharanenthiran <manish.dharanenthiran@oss.qualcomm.com>
Co-developed-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com>
Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250806111750.3214584-6-nithyanantham.paramasivam@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Ping-Ke Shih says:
==================
rtw-next patches for v6.18
Some small fixes and features are listed:
rtw88:
* correct LED function
rtw89:
* fix wait/completion racing of sending NULL data
* implement beacon tracking feature
* implement report channel noise function supported by RTL8852A
* correct RTL8851B RF calibration
* preparation of PCI TX/RX ring and interrupts for coming RTL8922DE
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Lockdep gives a splat [1] when ser_hdl_work item is executed. It is
scheduled at mac80211 workqueue via ieee80211_queue_work() and takes a
wiphy lock inside. However, this workqueue can be flushed when e.g.
closing the interface and wiphy lock is already taken in that case.
Choosing wiphy_work_queue() for SER is likely not suitable. Back on to
the global workqueue.
[1]:
WARNING: possible circular locking dependency detected
6.17.0-rc2 #17 Not tainted
------------------------------------------------------
kworker/u32:1/61 is trying to acquire lock:
ffff88811bc00768 (&rdev->wiphy.mtx){+.+.}-{4:4}, at: ser_state_run+0x5e/0x180 [rtw89_core]
but task is already holding lock:
ffffc9000048fd30 ((work_completion)(&ser->ser_hdl_work)){+.+.}-{0:0}, at: process_one_work+0x7b5/0x1450
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 ((work_completion)(&ser->ser_hdl_work)){+.+.}-{0:0}:
process_one_work+0x7c6/0x1450
worker_thread+0x49e/0xd00
kthread+0x313/0x640
ret_from_fork+0x221/0x300
ret_from_fork_asm+0x1a/0x30
-> #1 ((wq_completion)phy0){+.+.}-{0:0}:
touch_wq_lockdep_map+0x8e/0x180
__flush_workqueue+0x129/0x10d0
ieee80211_stop_device+0xa8/0x110
ieee80211_do_stop+0x14ce/0x2880
ieee80211_stop+0x13a/0x2c0
__dev_close_many+0x18f/0x510
__dev_change_flags+0x25f/0x670
netif_change_flags+0x7b/0x160
do_setlink.isra.0+0x1640/0x35d0
rtnl_newlink+0xd8c/0x1d30
rtnetlink_rcv_msg+0x700/0xb80
netlink_rcv_skb+0x11d/0x350
netlink_unicast+0x49a/0x7a0
netlink_sendmsg+0x759/0xc20
____sys_sendmsg+0x812/0xa00
___sys_sendmsg+0xf7/0x180
__sys_sendmsg+0x11f/0x1b0
do_syscall_64+0xbb/0x360
entry_SYSCALL_64_after_hwframe+0x77/0x7f
-> #0 (&rdev->wiphy.mtx){+.+.}-{4:4}:
__lock_acquire+0x124c/0x1d20
lock_acquire+0x154/0x2e0
__mutex_lock+0x17b/0x12f0
ser_state_run+0x5e/0x180 [rtw89_core]
rtw89_ser_hdl_work+0x119/0x220 [rtw89_core]
process_one_work+0x82d/0x1450
worker_thread+0x49e/0xd00
kthread+0x313/0x640
ret_from_fork+0x221/0x300
ret_from_fork_asm+0x1a/0x30
other info that might help us debug this:
Chain exists of:
&rdev->wiphy.mtx --> (wq_completion)phy0 --> (work_completion)(&ser->ser_hdl_work)
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock((work_completion)(&ser->ser_hdl_work));
lock((wq_completion)phy0);
lock((work_completion)(&ser->ser_hdl_work));
lock(&rdev->wiphy.mtx);
*** DEADLOCK ***
2 locks held by kworker/u32:1/61:
#0: ffff888103835148 ((wq_completion)phy0){+.+.}-{0:0}, at: process_one_work+0xefa/0x1450
#1: ffffc9000048fd30 ((work_completion)(&ser->ser_hdl_work)){+.+.}-{0:0}, at: process_one_work+0x7b5/0x1450
stack backtrace:
CPU: 0 UID: 0 PID: 61 Comm: kworker/u32:1 Not tainted 6.17.0-rc2 #17 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS edk2-20250523-14.fc42 05/23/2025
Workqueue: phy0 rtw89_ser_hdl_work [rtw89_core]
Call Trace:
<TASK>
dump_stack_lvl+0x5d/0x80
print_circular_bug.cold+0x178/0x1be
check_noncircular+0x14c/0x170
__lock_acquire+0x124c/0x1d20
lock_acquire+0x154/0x2e0
__mutex_lock+0x17b/0x12f0
ser_state_run+0x5e/0x180 [rtw89_core]
rtw89_ser_hdl_work+0x119/0x220 [rtw89_core]
process_one_work+0x82d/0x1450
worker_thread+0x49e/0xd00
kthread+0x313/0x640
ret_from_fork+0x221/0x300
ret_from_fork_asm+0x1a/0x30
</TASK>
Found by Linux Verification Center (linuxtesting.org).
Fixes: ebfc9199df ("wifi: rtw89: add wiphy_lock() to work that isn't held wiphy_lock() yet")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250919210852.823912-5-pchelkin@ispras.ru
The value of skb_data->wait indicates whether skb is passed on to the
core mac80211 stack or released by the driver itself. Make sure that by
the time skb is added to txwd queue and becomes visible to the completing
side, it has already allocated and initialized TX wait related data (in
case it's needed).
This is found by code review and addresses a possible race scenario
described below:
Waiting thread Completing thread
rtw89_core_send_nullfunc()
rtw89_core_tx_write_link()
...
rtw89_pci_txwd_submit()
skb_data->wait = NULL
/* add skb to the queue */
skb_queue_tail(&txwd->queue, skb)
/* another thread (e.g. rtw89_ops_tx) performs TX kick off for the same queue */
rtw89_pci_napi_poll()
...
rtw89_pci_release_txwd_skb()
/* get skb from the queue */
skb_unlink(skb, &txwd->queue)
rtw89_pci_tx_status()
rtw89_core_tx_wait_complete()
/* use incorrect skb_data->wait */
rtw89_core_tx_kick_off_and_wait()
/* assign skb_data->wait but too late */
Found by Linux Verification Center (linuxtesting.org).
Fixes: 1ae5ca6152 ("wifi: rtw89: add function to wait for completion of TX skbs")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250919210852.823912-3-pchelkin@ispras.ru
There is a bug observed when rtw89_core_tx_kick_off_and_wait() tries to
access already freed skb_data:
BUG: KFENCE: use-after-free write in rtw89_core_tx_kick_off_and_wait drivers/net/wireless/realtek/rtw89/core.c:1110
CPU: 6 UID: 0 PID: 41377 Comm: kworker/u64:24 Not tainted 6.17.0-rc1+ #1 PREEMPT(lazy)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS edk2-20250523-14.fc42 05/23/2025
Workqueue: events_unbound cfg80211_wiphy_work [cfg80211]
Use-after-free write at 0x0000000020309d9d (in kfence-#251):
rtw89_core_tx_kick_off_and_wait drivers/net/wireless/realtek/rtw89/core.c:1110
rtw89_core_scan_complete drivers/net/wireless/realtek/rtw89/core.c:5338
rtw89_hw_scan_complete_cb drivers/net/wireless/realtek/rtw89/fw.c:7979
rtw89_chanctx_proceed_cb drivers/net/wireless/realtek/rtw89/chan.c:3165
rtw89_chanctx_proceed drivers/net/wireless/realtek/rtw89/chan.h:141
rtw89_hw_scan_complete drivers/net/wireless/realtek/rtw89/fw.c:8012
rtw89_mac_c2h_scanofld_rsp drivers/net/wireless/realtek/rtw89/mac.c:5059
rtw89_fw_c2h_work drivers/net/wireless/realtek/rtw89/fw.c:6758
process_one_work kernel/workqueue.c:3241
worker_thread kernel/workqueue.c:3400
kthread kernel/kthread.c:463
ret_from_fork arch/x86/kernel/process.c:154
ret_from_fork_asm arch/x86/entry/entry_64.S:258
kfence-#251: 0x0000000056e2393d-0x000000009943cb62, size=232, cache=skbuff_head_cache
allocated by task 41377 on cpu 6 at 77869.159548s (0.009551s ago):
__alloc_skb net/core/skbuff.c:659
__netdev_alloc_skb net/core/skbuff.c:734
ieee80211_nullfunc_get net/mac80211/tx.c:5844
rtw89_core_send_nullfunc drivers/net/wireless/realtek/rtw89/core.c:3431
rtw89_core_scan_complete drivers/net/wireless/realtek/rtw89/core.c:5338
rtw89_hw_scan_complete_cb drivers/net/wireless/realtek/rtw89/fw.c:7979
rtw89_chanctx_proceed_cb drivers/net/wireless/realtek/rtw89/chan.c:3165
rtw89_chanctx_proceed drivers/net/wireless/realtek/rtw89/chan.c:3194
rtw89_hw_scan_complete drivers/net/wireless/realtek/rtw89/fw.c:8012
rtw89_mac_c2h_scanofld_rsp drivers/net/wireless/realtek/rtw89/mac.c:5059
rtw89_fw_c2h_work drivers/net/wireless/realtek/rtw89/fw.c:6758
process_one_work kernel/workqueue.c:3241
worker_thread kernel/workqueue.c:3400
kthread kernel/kthread.c:463
ret_from_fork arch/x86/kernel/process.c:154
ret_from_fork_asm arch/x86/entry/entry_64.S:258
freed by task 1045 on cpu 9 at 77869.168393s (0.001557s ago):
ieee80211_tx_status_skb net/mac80211/status.c:1117
rtw89_pci_release_txwd_skb drivers/net/wireless/realtek/rtw89/pci.c:564
rtw89_pci_release_tx_skbs.isra.0 drivers/net/wireless/realtek/rtw89/pci.c:651
rtw89_pci_release_tx drivers/net/wireless/realtek/rtw89/pci.c:676
rtw89_pci_napi_poll drivers/net/wireless/realtek/rtw89/pci.c:4238
__napi_poll net/core/dev.c:7495
net_rx_action net/core/dev.c:7557 net/core/dev.c:7684
handle_softirqs kernel/softirq.c:580
do_softirq.part.0 kernel/softirq.c:480
__local_bh_enable_ip kernel/softirq.c:407
rtw89_pci_interrupt_threadfn drivers/net/wireless/realtek/rtw89/pci.c:927
irq_thread_fn kernel/irq/manage.c:1133
irq_thread kernel/irq/manage.c:1257
kthread kernel/kthread.c:463
ret_from_fork arch/x86/kernel/process.c:154
ret_from_fork_asm arch/x86/entry/entry_64.S:258
It is a consequence of a race between the waiting and the signaling side
of the completion:
Waiting thread Completing thread
rtw89_core_tx_kick_off_and_wait()
rcu_assign_pointer(skb_data->wait, wait)
/* start waiting */
wait_for_completion_timeout()
rtw89_pci_tx_status()
rtw89_core_tx_wait_complete()
rcu_read_lock()
/* signals completion and
* proceeds further
*/
complete(&wait->completion)
rcu_read_unlock()
...
/* frees skb_data */
ieee80211_tx_status_ni()
/* returns (exit status doesn't matter) */
wait_for_completion_timeout()
...
/* accesses the already freed skb_data */
rcu_assign_pointer(skb_data->wait, NULL)
The completing side might proceed and free the underlying skb even before
the waiting side is fully awoken and run to execution. Actually the race
happens regardless of wait_for_completion_timeout() exit status, e.g.
the waiting side may hit a timeout and the concurrent completing side is
still able to free the skb.
Skbs which are sent by rtw89_core_tx_kick_off_and_wait() are owned by the
driver. They don't come from core ieee80211 stack so no need to pass them
to ieee80211_tx_status_ni() on completing side.
Introduce a work function which will act as a garbage collector for
rtw89_tx_wait_info objects and the associated skbs. Thus no potentially
heavy locks are required on the completing side.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 1ae5ca6152 ("wifi: rtw89: add function to wait for completion of TX skbs")
Cc: stable@vger.kernel.org
Suggested-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250919210852.823912-2-pchelkin@ispras.ru
In ath12k_dp_mon_rx_deliver_msdu(), peer lookup fails because
rxcb->peer_id is not updated with a valid value. This is expected
in monitor mode, where RX frames bypass the regular RX
descriptor path that typically sets rxcb->peer_id.
As a result, the peer is NULL, and link_id and link_valid fields
in the RX status are not populated. This leads to a WARN_ON in
mac80211 when it receives data frame from an associated station
with invalid link_id.
Fix this potential issue by using ppduinfo->peer_id, which holds
the correct peer id for the received frame. This ensures that the
peer is correctly found and the associated link metadata is updated
accordingly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: bd00cc7e8a ("wifi: ath12k: replace the usage of rx desc with rx_info")
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
Signed-off-by: Aishwarya R <aishwarya.r@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250724040552.1170642-1-aishwarya.r@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add support for simulating a NAN Device interface:
- Update interface limits to include support for NAN Device.
- Increase the number of supported HW addresses to allow unique
addresses for combination such as: station interface + P2P
Device interface + NAN Device interface.
- Declare support for NAN capabilities, specifically support for
NAN synchronization offload and NAN DE user space support.
- Add the relevant callbacks to support start/stop NAN Device
operation.
- Use a timer to simulate starting a Discovery Window (currently
the timer doesn't do much).
- Update the Tx path to simulate that the channel used for NAN
Device is either channel 6 or channel 149.
- Send DW notification when DW starts.
- Send cluster join notification when new cluster starts, or when an
existing cluster is joined. "Joining" is implemented by reusing the
cluster id of any other existing NAN management interface.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250908140015.2d02d5be6468.I3badfdb80c29e7713bd37373650ccbf099547a59@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, ath12k_mac_handle_beacon_miss() does not handle the beacon
miss for the MLO case.
In MLO scenarios, the host fails to process the beacon miss because the
vdev_id comparison in ath12k_mac_handle_beacon_miss_iter() does not match.
This mismatch occurs since arvif always points to ahvif->deflink, which may
not correspond to the actual vdev_id associated with the event.
Fix this by retrieving arvif from vdev_id instead of ahvif->deflink which
will work for both MLO and Non-MLO case.
Also refactor the ath12k_mac_handle_beacon_miss(), by passing arvif
directly instead of vdev_id and remove ath12k_mac_handle_beacon_miss_iter()
which is no longer needed.
ath12k_mac_handle_beacon_miss() is called from ath12k_roam_event() for WCN
chipsets and ath12k_peer_sta_kickout_event() for QCN chipsets.
So, refactor the ath12k_roam_event() to pass arvif instead vdev_id to the
ath12k_mac_handle_beacon_miss() function to align with the
ath12k_peer_sta_kickout_event() and change the rcu_read_lock() to
guard(rcu)() in the same function ath12k_roam_event().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Co-developed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250812111708.3686-4-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, when the non-AP STA connected to the AP STA, and the AP STA goes
down or becomes inactive without indication, firmware detects the beacon
miss and sends the WMI event WMI_PEER_STA_KICKOUT_EVENTID with reason as
INACTIVITY. The host driver handles this event as low ACK and reports it to
the mac80211 driver.
However, the expectation is that non-AP STA should be disconnected from
AP STA instantly once it receives the STA kickout event with reason of
inactivity.
Trigger a disconnect from AP STA through beacon miss handling upon
receiving non-AP STA peer kickout event with reason code inactivity.
Replace the helper function ath12k_mac_get_ar_by_vdev_id() with
ath12k_mac_get_arvif_by_vdev_id() due to the following reasons.
1. Check the station VIF type for handling the beacon miss.
2. Retrieve the proper ar from the arvif by checking the vdev_id with
vdev_map and link_map lookup which is needed for the MLO case in the
following patch.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Co-developed-by: Ramya Gnanasekar <ramya.gnanasekar@oss.qualcomm.com>
Signed-off-by: Ramya Gnanasekar <ramya.gnanasekar@oss.qualcomm.com>
Signed-off-by: Arulanbu Balusamy <quic_abalusam@quicinc.com>
Co-developed-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250812111708.3686-3-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, command “iw wlan0 station dump” does not show per-chain signal
strength.
This is because ath12k does not handle the num_per_chain_rssi and
rssi_avg_beacon reported by firmware to ath12k.
To address this, update ath12k to send WMI_REQUEST_STATS_CMDID with the
flag WMI_REQUEST_RSSI_PER_CHAIN_STAT to the firmware. Then, add logic to
handle num_per_chain_rssi and rssi_avg_beacon in the
ath12k_wmi_tlv_fw_stats_parse(), and assign the resulting per-chain signal
strength to the chain_signal of struct station_info.
After that, "iw dev xxx station dump" shows the correct per-chain signal
strength.
Such as:
Station AA:BB:CC:DD:EE:FF (on wlan0)
inactive time: 212 ms
rx bytes: 10398
rx packets: 64
tx bytes: 4362
tx packets: 33
tx retries: 49
tx failed: 0
beacon loss: 0
beacon rx: 14
rx drop misc: 16
signal: -45 [-51, -46] dBm
beacon signal avg: -44 dBm
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219751
Signed-off-by: Lingbo Kong <lingbo.kong@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250812030044.688-1-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Use the newly added of_reserved_mem_region_to_resource() function to
handle "memory-region" properties.
The error handling is a bit different for ath10k. "memory-region" is
optional, so failed lookup is not an error. But then an error in
of_address_to_resource() is treated as an error. However, that
distinction is not really important. Either the region is available
and usable or it is not. So now, it is just
of_reserved_mem_region_to_resource() which is checked for an error.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250813214933.897486-1-robh@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
