Currently, during the LAN8814 PTP probe shared->phydev is only set if PTP
clock gets actually set, otherwise the function will return before setting
it.
This is an issue as shared->phydev is unconditionally being used when IRQ
is being handled, especially in lan8814_gpio_process_cap and since it was
not set it will cause a NULL pointer exception and crash the kernel.
So, simply always set shared->phydev to avoid the NULL pointer exception.
Fixes: b3f1a08fcf ("net: phy: micrel: Add support for PTP_PF_EXTTS for lan8814")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20251021132034.983936-1-robert.marko@sartura.hr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The blamed commit introduced the function lanphy_modify_page_reg which
as name suggests it, it modifies the registers. In the same commit we
have started to use this function inside the drivers. The problem is
that in the function lan8814_config_init we passed the wrong page number
when disabling the aneg towards host side. We passed extended page number
4(LAN8814_PAGE_COMMON_REGS) instead of extended page
5(LAN8814_PAGE_PORT_REGS)
Fixes: a0de636ed7 ("net: phy: micrel: Introduce lanphy_modify_page_reg")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250925064702.3906950-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for fast link failure for lan8842, when this is enabled the
PHY will detect link down immediately (~1ms). The disadvantage of this
is that also small instability might be reported as link down.
Therefore add this feature as a tunable configuration and the user will
know when to enable or not. By default it is not enabled.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250917104630.3931969-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It has the same PTP IP block as lan8814, only the number of GPIOs is
different, all the other functionality is the same. So reuse the same
functions as lan8814 for lan8842.
There is a revision of lan8842 called lan8832 which doesn't have the PTP
IP block. So make sure in that case the PTP is not initialized.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20250902121832.3258544-3-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The LAN8842 is a low-power, single port triple-speed (10BASE-T/ 100BASE-TX/
1000BASE-T) ethernet physical layer transceiver (PHY) that supports
transmission and reception of data on standard CAT-5, as well as CAT-5e and
CAT-6, Unshielded Twisted Pair (UTP) cables.
The LAN8842 supports industry-standard SGMII (Serial Gigabit Media
Independent Interface) providing chip-to-chip connection to a Gigabit
Ethernet MAC using a single serialized link (differential pair) in each
direction.
There are 2 variants of the lan8842. The one that supports timestamping
(lan8842) and one that doesn't have timestamping (lan8832).
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250818075121.1298170-5-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Merge in late fixes to prepare for the 6.17 net-next PR.
Conflicts:
net/core/neighbour.c
1bbb76a899 ("neighbour: Fix null-ptr-deref in neigh_flush_dev().")
13a936bb99 ("neighbour: Protect tbl->phash_buckets[] with a dedicated mutex.")
03dc03fa04 ("neighbor: Add NTF_EXT_VALIDATED flag for externally validated entries")
Adjacent changes:
drivers/net/usb/usbnet.c
0d9cfc9b8c ("net: usbnet: Avoid potential RCU stall on LINK_CHANGE event")
2c04d279e8 ("net: usb: Convert tasklet API to new bottom half workqueue mechanism")
net/ipv6/route.c
31d7d67ba1 ("ipv6: annotate data-races around rt->fib6_nsiblings")
1caf272972 ("ipv6: adopt dst_dev() helper")
3b3ccf9ed0 ("net: Remove unnecessary NULL check for lwtunnel_fill_encap()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 21b688dabe ("net: phy: micrel: Cable Diag feature for lan8814
phy") introduced cable_test support for the LAN8814 that reuses parts of
the KSZ886x logic and introduced the cable_diag_reg and pair_mask
parameters to account for differences between those chips.
However, it did not update the ksz8081_type struct, so those members are
now 0, causing no pairs to be tested in ksz886x_cable_test_get_status
and ksz886x_cable_test_wait_for_completion to poll the wrong register
for the affected PHYs (Basic Control/Reset, which is 0 in normal
operation) and exit immediately.
Fix this by setting both struct members accordingly.
Fixes: 21b688dabe ("net: phy: micrel: Cable Diag feature for lan8814 phy")
Cc: stable@vger.kernel.org
Signed-off-by: Florian Larysch <fl@n621.de>
Link: https://patch.msgid.link/20250723222250.13960-1-fl@n621.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the Signal Quality Indicator (SQI) feature on KSZ9477
family switches, providing a relative measure of receive signal quality.
The hardware exposes separate SQI readings per channel. For 1000BASE-T,
all four channels are read. For 100BASE-TX, only one channel is reported,
but which receive pair is active depends on Auto MDI-X negotiation, which
is not exposed by the hardware. Therefore, it is not possible to reliably
map the measured channel to a specific wire pair.
This resolves an earlier discussion about how to handle multi-channel
SQI. Originally, the plan was to expose all channels individually.
However, since pair mapping is sometimes unavailable, this
implementation treats SQI as a per-link metric instead. This fallback
avoids ambiguity and ensures consistent behavior. The existing get_sqi()
UAPI was designed for single-pair Ethernet (SPE), where per-pair and
per-link are effectively equivalent. Restricting its use to per-link
metrics does not introduce regressions for existing users.
The raw 7-bit SQI value (0–127, lower is better) is converted to the
standard 0–7 (high is better) scale. Empirical testing showed that the
link becomes unstable around a raw value of 8.
The SQI raw value remains zero if no data is received, even if noise is
present. This confirms that the measurement reflects the "quality" during
active data reception rather than the passive line state. User space
must ensure that traffic is present on the link to obtain valid SQI
readings.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20250627112539.895255-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable cable test support for KSZ9477-class PHYs by reusing the
existing KSZ9131 implementation.
This also adds support for 100Mbit-only PHYs like KSZ8563, which are
identified as KSZ9477. For these PHYs, only two wire pairs (A and B)
are active, so the cable test logic limits the pair_mask accordingly.
Support for KSZ8563 is untested but added based on its register
compatibility and PHY ID match.
Tested on KSZ9893 (Gigabit): open and short conditions were correctly
detected on all four pairs. Fault length reporting is functional and
varies by pair. For example:
- 2m cable: open faults reported ~1.2m (pairs B–D), 0.0m (pair A)
- No cable: all pairs report 0.0m fault length
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250610091354.4060454-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for tracking receive error statistics from PHYs integrated
into the KSZ9477 family of Ethernet switches.
The integrated PHYs expose a receive error (RXER) counter in register 0x15.
This counter increments when the PHY detects one or more symbol errors
on a received frame. The register is cleared upon reading.
Changes include:
- `kszphy_update_stats()` to accumulate the RX error count.
- `kszphy_get_phy_stats()` to expose this count via ethtool PHY stats.
- Addition of a private `rx_err_pkt_cnt` field in the driver.
- Registration of `.update_stats` and `.get_phy_stats` callbacks in the
KSZ9477 PHY driver structure.
The functionality of this counter was confirmed by physically disturbing
the signal lines - specifically by wiggling exposed twisted pair wires and
intentionally shorting between pairs. These actions triggered RXER
increments, validating the counter's behavior.
This RXER counter is confirmed for KSZ9477 and likely applicable to
other related PHYs like those in KSZ9313.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250610091354.4060454-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add MDI/MDI-X configuration support for PHYs integrated in the KSZ9477
family of Ethernet switches.
All MDI/MDI-X configuration modes are supported:
- Automatic MDI/MDI-X (ETH_TP_MDI_AUTO)
- Forced MDI (ETH_TP_MDI)
- Forced MDI-X (ETH_TP_MDI_X)
However, when operating in automatic mode, the PHY does not expose the
resolved crossover status (i.e., whether MDI or MDI-X is active).
Therefore, in auto mode, the driver reports ETH_TP_MDI_INVALID as
the current status.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250610091354.4060454-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass PHY driver pointer to .match_phy_device OP in addition to phydev.
Having access to the PHY driver struct might be useful to check the
PHY ID of the driver is being matched for in case the PHY ID scanned in
the phydev is not consistent.
A scenario for this is a PHY that change PHY ID after a firmware is
loaded, in such case, the PHY ID stored in PHY device struct is not
valid anymore and PHY will manually scan the ID in the match_phy_device
function.
Having the PHY driver info is also useful for those PHY driver that
implement multiple simple .match_phy_device OP to match specific MMD PHY
ID. With this extra info if the parsing logic is the same, the matching
function can be generalized by using the phy_id in the PHY driver
instead of hardcoding.
Rust wrapper callback is updated to align to the new match_phy_device
arguments.
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Benno Lossin <lossin@kernel.org> # for Rust
Reviewed-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-2-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The KSZ9477 PHY driver contained workarounds for broken EEE capability
advertisements by manually masking supported EEE modes and forcibly
disabling EEE if MICREL_NO_EEE was set.
With proper MAC-side EEE handling implemented via phylink, these quirks
are no longer necessary. Remove MICREL_NO_EEE handling and the use of
ksz9477_get_features().
This simplifies the PHY driver and avoids duplicated EEE management logic.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org # v6.14+
Link: https://patch.msgid.link/20250504081434.424489-3-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The PTP_PEROUT_REQUEST2 ioctl has gained support for flags specifying
specific output behavior including PTP_PEROUT_ONE_SHOT,
PTP_PEROUT_DUTY_CYCLE, PTP_PEROUT_PHASE.
Driver authors are notorious for not checking the flags of the request.
This results in misinterpreting the request, generating an output signal
that does not match the requested value. It is anticipated that even more
flags will be added in the future, resulting in even more broken requests.
Expecting these issues to be caught during review or playing whack-a-mole
after the fact is not a great solution.
Instead, introduce the supported_perout_flags field in the ptp_clock_info
structure. Update the core character device logic to explicitly reject any
request which has a flag not on this list.
This ensures that drivers must 'opt in' to the flags they support. Drivers
which don't set the .supported_perout_flags field will not need to check
that unsupported flags aren't passed, as the core takes care of this.
Update the drivers which do support flags to set this new field.
Note the following driver files set n_per_out to a non-zero value but did
not check the flags at all:
• drivers/ptp/ptp_clockmatrix.c
• drivers/ptp/ptp_idt82p33.c
• drivers/ptp/ptp_fc3.c
• drivers/net/ethernet/ti/am65-cpts.c
• drivers/net/ethernet/aquantia/atlantic/aq_ptp.c
• drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c
• drivers/net/dsa/sja1105/sja1105_ptp.c
• drivers/net/ethernet/freescale/dpaa2/dpaa2-ptp.c
• drivers/net/ethernet/mscc/ocelot_vsc7514.c
• drivers/net/ethernet/intel/i40e/i40e_ptp.c
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250414-jk-supported-perout-flags-v2-2-f6b17d15475c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PTP_EXTTS_REQUEST(2) ioctl has a flags field which specifies how the
external timestamp request should behave. This includes which edge of the
signal to timestamp, as well as a specialized "offset" mode. It is expected
that more flags will be added in the future.
Driver authors routinely do not check the flags, often accepting requests
with flags which they do not support. Even drivers which do check flags may
not be future-proofed to reject flags not yet defined. Thus, any future
flag additions often require manually updating drivers to reject these
flags.
This approach of hoping we catch flag checks during review, or playing
whack-a-mole after the fact is the wrong approach.
Introduce the "supported_extts_flags" field to the ptp_clock_info
structure. This field defines the set of flags the device actually
supports.
Update the core character device logic to check this field and reject
unsupported requests. Getting this right is somewhat tricky. First, to
avoid unnecessary repetition and make basic functionality work when
.supported_extts_flags is 0, the core always accepts the PTP_ENABLE_FEATURE
flag. This flag is used to set the 'on' parameter to the .enable function
and is thus always 'supported' by all drivers.
For backwards compatibility, the PTP_RISING_EDGE and PTP_FALLING_EDGE flags
are merely "hints" when using the old PTP_EXTTS_REQUEST ioctl, and are not
expected to be enforced. If the user issues PTP_EXTTS_REQUEST2, the
PTP_STRICT_FLAGS flag is added which is supposed to inform the driver to
strictly validate the flags and reject unsupported requests. To handle
this, first check if the driver reports PTP_STRICT_FLAGS support. If it
does not, then always allow the PTP_RISING_EDGE and PTP_FALLING_EDGE flags.
This keeps backwards compatibility with the original PTP_EXTTS_REQUEST
ioctl where these flags are not guaranteed to be honored.
This way, drivers which do not set the supported_extts_flags will continue
to accept requests for the original PTP_EXTTS_REQUEST ioctl. The core will
automatically reject requests with new flags, and correctly reject requests
with PTP_STRICT_FLAGS, where the driver is supposed to strictly validate
the flags.
Update the various drivers, refactoring their validation logic into the
.supported_extts_flags field. For consistency and readability,
PTP_ENABLE_FEATURE is not set in the supported flags list, and
PTP_EXTTS_EDGES is expanded to PTP_RISING_EDGE | PTP_FALLING_EDGE in all
cases.
Note the following driver files set n_ext_ts to a non-zero value but did
not check flags at all:
• drivers/net/ethernet/freescale/dpaa2/dpaa2-ptp.c
• drivers/net/ethernet/freescale/enetc/enetc_ptp.c
• drivers/net/ethernet/intel/i40e/i40e_ptp.c
• drivers/net/ethernet/marvell/octeontx2/nic/otx2_ptp.c
• drivers/net/ethernet/renesas/ravb_ptp.c
• drivers/net/ethernet/renesas/rtsn.c
• drivers/net/ethernet/renesas/rtsn.h
• drivers/net/ethernet/ti/am65-cpts.c
• drivers/net/ethernet/ti/cpts.h
• drivers/net/ethernet/ti/icssg/icss_iep.c
• drivers/net/ethernet/xscale/ptp_ixp46x.c
• drivers/net/phy/bcm-phy-ptp.c
• drivers/ptp/ptp_ocp.c
• drivers/ptp/ptp_pch.c
• drivers/ptp/ptp_qoriq.c
These drivers behavior does change slightly: they will now reject the
PTP_EXTTS_REQUEST2 ioctl, because they do not strictly validate their
flags. This also makes them no longer incorrectly accept PTP_EXT_OFFSET.
Also note that the renesas ravb driver does not support PTP_STRICT_FLAGS.
We could leave the .supported_extts_flags as 0, but I added the
PTP_RISING_EDGE | PTP_FALLING_EDGE since the driver previously manually
validated these flags. This is equivalent to 0 because the core will allow
these flags regardless unless PTP_STRICT_FLAGS is also set.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250414-jk-supported-perout-flags-v2-1-f6b17d15475c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On the i.MX6ULL-14x14-EVK board, enet1_ref and enet2_ref are used as the
clock sources for two external KSZ PHYs. However, after closing the two
FEC ports, the clk_enable_count of the enet1_ref and enet2_ref clocks is
not 0. The root cause is that since the commit 9853294627 ("net: phy:
micrel: use devm_clk_get_optional_enabled for the rmii-ref clock"), the
external clock of KSZ PHY has been enabled when the PHY driver probes,
and it can only be disabled when the PHY driver is removed. This causes
the clock to continue working when the system is suspended or the network
port is down.
Although Heiko explained in the commit message that the patch was because
some clock suppliers need to enable the clock to get the valid clock rate
, it seems that the simple fix is to disable the clock after getting the
clock rate to solve the current problem. This is indeed true, but we need
to admit that Heiko's patch has been applied for more than a year, and we
cannot guarantee whether there are platforms that only enable rmii-ref in
the KSZ PHY driver during this period. If this is the case, disabling
rmii-ref will cause RMII on these platforms to not work.
Secondly, commit 99ac4cbcc2 ("net: phy: micrel: allow usage of generic
ethernet-phy clock") just simply enables the generic clock permanently,
which seems like the generic clock may only be enabled in the PHY driver.
If we simply disable the generic clock, RMII may not work. If we keep it
as it is, the platform using the generic clock will have the same problem
as the i.MX6ULL platform.
To solve this problem, the clock is enabled when phy_driver::resume() is
called, and the clock is disabled when phy_driver::suspend() is called.
Since phy_driver::resume() and phy_driver::suspend() are not called in
pairs, an additional clk_enable flag is added. When phy_driver::suspend()
is called, the clock is disabled only if clk_enable is true. Conversely,
when phy_driver::resume() is called, the clock is enabled if clk_enable
is false.
The changes that introduced the problem were only a few lines, while the
current fix is about a hundred lines, which seems out of proportion, but
it is necessary because kszphy_probe() is used by multiple KSZ PHYs and
we need to fix all of them.
Fixes: 9853294627 ("net: phy: micrel: use devm_clk_get_optional_enabled for the rmii-ref clock")
Fixes: 99ac4cbcc2 ("net: phy: micrel: allow usage of generic ethernet-phy clock")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20241217063500.1424011-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MDIX status is not accurately reflecting the current state after the link
partner has manually altered its MDIX configuration while operating in forced
mode.
Access information about Auto mdix completion and pair selection from the
KSZ9131's Auto/MDI/MDI-X status register
Fixes: b64e6a8794 ("net: phy: micrel: Add PHY Auto/MDI/MDI-X set driver for KSZ9131")
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240725071125.13960-1-Raju.Lakkaraju@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In prevision to add new UAPI for hwtstamp we will be limited to the struct
ethtool_ts_info that is currently passed in fixed binary format through the
ETHTOOL_GET_TS_INFO ethtool ioctl. It would be good if new kernel code
already started operating on an extensible kernel variant of that
structure, similar in concept to struct kernel_hwtstamp_config vs struct
hwtstamp_config.
Since struct ethtool_ts_info is in include/uapi/linux/ethtool.h, here
we introduce the kernel-only structure in include/linux/ethtool.h.
The manual copy is then made in the function called by ETHTOOL_GET_TS_INFO.
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-6-b5317f50df2a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change the API to select MAC default time stamping instead of the PHY.
Indeed the PHY is closer to the wire therefore theoretically it has less
delay than the MAC timestamping but the reality is different. Due to lower
time stamping clock frequency, latency in the MDIO bus and no PHC hardware
synchronization between different PHY, the PHY PTP is often less precise
than the MAC. The exception is for PHY designed specially for PTP case but
these devices are not very widespread. For not breaking the compatibility
default_timestamp flag has been introduced in phy_device that is set by
the phy driver to know we are using the old API behavior.
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-4-b5317f50df2a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PHY_ID_KSZ9477 was supported but not added to the device table passed to
MODULE_DEVICE_TABLE.
Fixes: fc3973a1fa ("phy: micrel: add Microchip KSZ 9477 Switch PHY support")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ8061 needs to write to a MMD register at driver initialization to fix
an errata. This worked in 5.0 kernel but not in newer kernels. The
issue is the main phylib code no longer resets PHY at the very beginning.
Calling phy resuming code later will reset the chip if it is already
powered down at the beginning. This wipes out the MMD register write.
Solution is to implement a phy resume function for KSZ8061 to take care
of this problem.
Fixes: 232ba3a51c ("net: phy: Micrel KSZ8061: link failure after cable connect")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PHY is powered up after powered down most of the registers are
reset, so the PHY setup code needs to be done again. In addition the
interrupt register will need to be setup again so that link status
indication works again.
Fixes: 26dd2974c5 ("net: phy: micrel: Move KSZ9477 errata fixes to PHY driver")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the interrupt is enabled, the function lan8841_config_intr tries to
clear any pending interrupts by reading the interrupt status, then
checks the return value for errors and then continue to enable the
interrupt. It has been seen that once the system gets out of sleep mode,
the interrupt status has the value 0x400 meaning that the PHY detected
that the link was in low power. That is correct value but the problem is
that the check is wrong. We try to check for errors but we return an
error also in this case which is not an error. Therefore fix this by
returning only when there is an error.
Fixes: a8f1a19d27 ("net: micrel: Add support for lan8841 PHY")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240524085350.359812-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The blamed commit started to use the ptp workqueue to get the second
part of the timestamp. And when the port was set down, then this
workqueue is stopped. But if the config option NETWORK_PHY_TIMESTAMPING
is not enabled, then the ptp_clock is not initialized so then it would
crash when it would try to access the delayed work.
So then basically by setting up and then down the port, it would crash.
The fix consists in checking if the ptp_clock is initialized and only
then cancel the delayed work.
Fixes: cc75549548 ("net: micrel: Change to receive timestamp in the frame for lan8841")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the PTP programmable gpios to implement also PTP_PF_EXTTS
function. The pins can be configured to capture both of rising
and falling edge. Once the event is seen, then an interrupt is
generated and the LTC is saved in the registers.
On lan8814 only GPIO 3 can be configured for this.
This was tested using:
ts2phc -m -l 7 -s generic -f ts2phc.cfg
Where the configuration was the following:
---
[global]
ts2phc.pin_index 3
[eth0]
---
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lan8814 has 24 GPIOs but only 2 GPIOs (GPIO 0 and GPIO 1) can be
configured to generate period signals. And there are 2 events (EVENT_A
and EVENT_B) but these events are hardcoded to the GPIO 0 and GPIO 1.
These events are used to generate period signals. It is possible to
configure the length, the start time and the period of the signal by
configuring the event.
These events are generated by comparing the target time with the PHC
time. In case the PHC time is changed to a value bigger than the target
time + reload time, then it would generate only 1 event and then it
would stop because target time + reload time is smaller than PHC time.
Therefore it is required to change also the target time every time when
the PHC is changed. The same will apply also when the PHC time is
changed to a smaller value.
This was tested using:
testptp -i 1 -L 1,2
testptp -i 1 -p 1000000000 -w 200000000
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The LTC for lan8814 was enabled only if timestamping was enabled,
otherwise it would be stopped. Meaning that LTC will not increase by
itself. This might break other features that don't required timestamping
like generating 1PPS. Therefore enable the LTC at probe time.
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are 2 issues with the blamed commit.
1. When the phy is initialized, it would enable the disabled of UDPv4
checksums. The UDPv6 checksum is already enabled by default. So when
1-step is configured then it would clear these flags.
2. After the 1-step is configured, then if 2-step is configured then the
1-step would be still configured because it is not clearing the flag.
So the sync frames will still have origin timestamps set.
Fix this by reading first the value of the register and then
just change bit 12 as this one determines if the timestamp needs to
be inserted in the frame, without changing any other bits.
Fixes: ece1950283 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Link: https://lore.kernel.org/r/20240402071634.2483524-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In lan8814_get_sig_rx() and lan8814_get_sig_tx() ptp_parse_header() may
return NULL as ptp_header due to abnormal packet type or corrupted packet.
Fix this bug by adding ptp_header check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: ece1950283 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240329061631.33199-1-amishin@t-argos.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the length of the cable is more than 100m and the lan8814 is
configured to run in 1000Base-T Slave then the register of the device
needs to be optimized.
Workaround this by setting the measure time to a value of 0xb. This
value can be set regardless of the configuration.
This issue is described in 'LAN8814 Silicon Errata and Data Sheet
Clarification' and according to that, this will not be corrected in a
future silicon revision.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240304091548.1386022-3-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
