The Lenovo Legion Go is a handheld gaming system, similar to a Steam Deck.
It has a gamepad (including rear paddles), 3 gyroscopes, a trackpad,
volume buttons, a power button, and 2 LED ring lights.
The Legion Go firmware presents these controls as a USB hub with various
devices attached. In its default state, the gamepad is presented as an
Xbox controller connected to this hub. (By holding a combination of
buttons, it can be changed to use the older DirectInput API.)
This patch teaches the existing Xbox controller module `xpad` to bind to
the controller in the Legion Go, which enables support for the:
- directional pad,
- analog sticks (including clicks),
- X, Y, A, B,
- start and select (or menu and capture),
- shoulder buttons, and
- rumble.
The trackpad, touchscreen, volume controls, and power button are already
supported via existing kernel modules. Two of the face buttons, the
gyroscopes, rear paddles, and LEDs are not.
After this patch lands, the Legion Go will be mostly functional in Linux,
out-of-the-box. The various components of the USB hub can be synthesized
into a single logical controller (including the additional buttons) in
userspace with [Handheld Daemon](https://github.com/hhd-dev/hhd), which
makes the Go fully functional.
Signed-off-by: Brenton Simpson <appsforartists@google.com>
Link: https://lore.kernel.org/r/20240118183546.418064-1-appsforartists@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some devices list 3 Gpio resources in the ACPI resource list for
the touchscreen:
1. GpioInt resource pointing to the GPIO used for the interrupt
2. GpioIo resource pointing to the reset GPIO
3. GpioIo resource pointing to the GPIO used for the interrupt
Note how the third extra GpioIo resource really is a duplicate
of the GpioInt provided info.
Ignore this extra GPIO, treating this setup the same as gpio_count == 2 &&
gpio_int_idx == 0 fixes the touchscreen not working on the Thunderbook
Colossus W803 rugged tablet and likely also on the CyberBook_T116K.
Reported-by: Maarten van der Schrieck
Closes: https://gitlab.com/AdyaAdya/goodix-touchscreen-linux-driver/-/issues/22
Suggested-by: Maarten van der Schrieck
Tested-by: Maarten van der Schrieck
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231223141650.10679-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- a new driver for Adafruit Seesaw gamepad device
- Zforce touchscreen will handle standard device properties for axis
swap/inversion
- handling of advanced sensitivity settings in Microchip CAP11xx
capacitive sensor driver
- more drivers have been converted to use newer gpiod API
- support for dedicated wakeup IRQs in gpio-keys dirver
- support for slider gestures and OTP variants in iqs269a driver
- atkbd will report keyboard version as 0xab83 in cases when GET ID
command was skipped (to deal with problematic firmware on newer
laptops), restoring the previous behavior
- other assorted cleanups and changes
* tag 'input-for-v6.8-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (44 commits)
Input: atkbd - use ab83 as id when skipping the getid command
Input: driver for Adafruit Seesaw Gamepad
dt-bindings: input: bindings for Adafruit Seesaw Gamepad
Input: da9063_onkey - avoid explicitly setting input's parent
Input: da9063_onkey - avoid using OF-specific APIs
Input: iqs269a - add support for OTP variants
dt-bindings: input: iqs269a: Add bindings for OTP variants
Input: iqs269a - add support for slider gestures
dt-bindings: input: iqs269a: Add bindings for slider gestures
Input: gpio-keys - filter gpio_keys -EPROBE_DEFER error messages
Input: zforce_ts - accept standard touchscreen properties
dt-bindings: touchscreen: neonode,zforce: Use standard properties
dt-bindings: touchscreen: convert neonode,zforce to json-schema
dt-bindings: input: convert drv266x to json-schema
Input: da9063 - use dev_err_probe()
Input: da9063 - drop redundant prints in probe()
Input: da9063 - simplify obtaining OF match data
Input: as5011 - convert to GPIO descriptor
Input: omap-keypad - drop optional GPIO support
Input: tca6416-keypad - drop unused include
...
This driver does not use the SPI core as it should, instead tampering
with the SSP registers manually. Refactoring the driver is almost
certainly not worth it as the hardware seems to have been designed for
and used only in the HP iPAQ hx4700 removed more than a year ago in
d6df7df7ae ("ARM: pxa: remove unused board files"), so let's remove
it.
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20240116-navpoint-removal-v2-2-e566806f1009@skole.hr
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull pwm updates from Thierry Reding:
"This contains a bunch of cleanups and simplifications across the
board, as well as a number of small fixes.
Perhaps the most notable change here is the addition of an API that
allows PWMs to be used in atomic contexts, which is useful when time-
critical operations are involved, such as using a PWM to generate IR
signals.
Finally, I have decided to step down as PWM subsystem maintainer. Due
to other responsibilities I have lately not been able to find the time
that the subsystem deserves and Uwe, who has been helping out a lot
for the past few years and has many things planned for the future, has
kindly volunteered to take over. I have no doubt that he will be a
suitable replacement"
* tag 'pwm/for-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
MAINTAINERS: pwm: Thierry steps down, Uwe takes over
pwm: linux/pwm.h: fix Excess kernel-doc description warning
pwm: Add pwm_apply_state() compatibility stub
pwm: cros-ec: Drop documentation for dropped struct member
pwm: Drop two unused API functions
pwm: lpc18xx-sct: Don't modify the cached period of other PWM outputs
pwm: meson: Simplify using dev_err_probe()
pwm: stmpe: Silence duplicate error messages
pwm: Reduce number of pointer dereferences in pwm_device_request()
pwm: crc: Use consistent variable naming for driver data
pwm: omap-dmtimer: Drop locking
dt-bindings: pwm: ti,pwm-omap-dmtimer: Update binding for yaml
media: pwm-ir-tx: Trigger edges from hrtimer interrupt context
pwm: bcm2835: Allow PWM driver to be used in atomic context
pwm: Make it possible to apply PWM changes in atomic context
pwm: renesas: Remove unused include
pwm: Replace ENOTSUPP with EOPNOTSUPP
pwm: Rename pwm_apply_state() to pwm_apply_might_sleep()
pwm: Stop referencing pwm->chip
pwm: Update kernel doc for struct pwm_chip
...
Pull media updates from Mauro Carvalho Chehab:
- v4l core: subdev frame interval now supports which field
- v4l kapi: moves and renames the init_cfg pad op to init_state as an
internal op.
- new sensor drivers: gc0308, gc2145, Avnet Alvium, ov64a40, tw9900
- new camera driver: STM32 DCMIPP
- s5p-mfc has gained MFC v12 support
- new ISP driver added to staging: Starfive
- new stateful encoder/decoded: Wave5 codec It is found on the J721S2
SoC, JH7100 SoC, ssd202d SoC. Etc.
- fwnode gained support for MIPI "DisCo for Imaging"
(https://www.mipi.org/specifications/mipi-disco-imaging)
- as usual, lots of cleanups, fixups and driver improvements.
* tag 'media/v6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (309 commits)
media: i2c: thp7312: select CONFIG_FW_LOADER
media: i2c: mt9m114: use fsleep() in place of udelay()
media: videobuf2: core: Rename min_buffers_needed field in vb2_queue
media: i2c: thp7312: Store frame interval in subdev state
media: docs: uAPI: Fix documentation of 'which' field for routing ioctls
media: docs: uAPI: Expand error documentation for invalid 'which' value
media: docs: uAPI: Clarify error documentation for invalid 'which' value
media: v4l2-subdev: Store frame interval in subdev state
media: v4l2-subdev: Add which field to struct v4l2_subdev_frame_interval
media: v4l2-subdev: Turn .[gs]_frame_interval into pad operations
media: v4l: subdev: Move out subdev state lock macros outside CONFIG_MEDIA_CONTROLLER
media: s5p-mfc: DPB Count Independent of VIDIOC_REQBUF
media: s5p-mfc: Load firmware for each run in MFCv12.
media: s5p-mfc: Set context for valid case before calling try_run
media: s5p-mfc: Add support for DMABUF for encoder
media: s5p-mfc: Add support for UHD encoding.
media: s5p-mfc: Add support for rate controls in MFCv12
media: s5p-mfc: Add YV12 and I420 multiplanar format support
media: s5p-mfc: Add initial support for MFCv12
media: s5p-mfc: Rename IS_MFCV10 macro
...
Adds a driver for a mini gamepad that communicates over i2c, the gamepad
has bidirectional thumb stick input and six buttons.
The gamepad chip utilizes the open framework from Adafruit called 'Seesaw'
to transmit the ADC data for the joystick and digital pin state for the
buttons. I have only implemented the functionality required to receive the
thumb stick and button state.
Steps in reading the gamepad state over i2c:
1. Reset the registers
2. Set the pin mode of the pins specified by the `BUTTON_MASK` to input
`BUTTON_MASK`: A bit-map for the six digital pins internally
connected to the joystick buttons.
3. Enable internal pullup resistors for the `BUTTON_MASK`
4. Bulk set the pin state HIGH for `BUTTON_MASK`
5. Poll the device for button and joystick state done by:
`seesaw_read_data(struct i2c_client *client, struct seesaw_data *data)`
Product page:
https://www.adafruit.com/product/5743
Arduino driver:
https://github.com/adafruit/Adafruit_Seesaw
Driver tested on RPi Zero 2W
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Anshul Dalal <anshulusr@gmail.com>
Link: https://lore.kernel.org/r/20240106015111.882325-2-anshulusr@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull spi updates from Mark Brown:
"A moderately busy release for SPI, the main core update was the
merging of support for multiple chip selects, used in some flash
configurations. There were also big overhauls for the AXI SPI Engine
and PL022 drivers, plus some new device support for ST.
There's a few patches for other trees, API updates to allow the
multiple chip select support and one of the naming modernisations
touched a controller embedded in the USB code.
- Support for multiple chip selects.
- A big overhaul for the AXI SPI engine driver, modernising it and
adding a bunch of new features.
- Modernisation of the PL022 driver, fixing some issues with
submitting messages while in atomic context in the process.
- Many drivers were converted to use new APIs which avoid outdated
terminology for devices and controllers.
- Support for ST Microelectronics STM32F7 and STM32MP25, and Renesas
RZ/Five"
* tag 'spi-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (83 commits)
spi: stm32: add st,stm32mp25-spi compatible supporting STM32MP25 soc
dt-bindings: spi: stm32: add st,stm32mp25-spi compatible
spi: stm32: use dma_get_slave_caps prior to configuring dma channel
spi: axi-spi-engine: fix struct member doc warnings
spi: pl022: update description of internal_cs_control()
spi: pl022: delete description of cur_msg
spi: dw: Remove Intel Thunder Bay SOC support
spi: dw: Remove Intel Thunder Bay SOC support
spi: sh-msiof: Enforce fixed DTDL for R-Car H3
spi: ljca: switch to use devm_spi_alloc_host()
spi: cs42l43: switch to use devm_spi_alloc_host()
spi: zynqmp-gqspi: switch to use modern name
spi: zynq-qspi: switch to use modern name
spi: xtensa-xtfpga: switch to use modern name
spi: xlp: switch to use modern name
spi: xilinx: switch to use modern name
spi: xcomm: switch to use modern name
spi: uniphier: switch to use modern name
spi: topcliff-pch: switch to use modern name
spi: wpcm-fiu: switch to use devm_spi_alloc_host()
...
This patch adds support for each available OTP variant of the device.
The OTP configuration cannot be read over I2C, so it is derived from
a compatible string instead.
Early revisions of the D0 order code require their OTP-enabled func-
tionality to be manually restored following a soft reset; this patch
accommodates this erratum as well.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/ZZMaZbdk6iAKUjlm@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds support for slider gestures that can be expressed
by the device. Each gesture (e.g. tap or hold) can be mapped to a
unique keycode for either slider 0 or 1.
With this change, raw slider coordinates are reported only if the
slider has no keycodes defined. This prevents unwanted mouse cur-
sor movement when expressing axial gestures (e.g. swipe) and also
eliminates some unnecessary I2C traffic.
Different revisions of silicon use different tap and swipe timeout
step sizes. Apply an appropriate scaling factor depending on which
revision is found.
To facilitate this change, store the iqs269_ver_info struct in the
driver's private data so that other functions can use it after the
driver has probed.
Last but not least, a former reserved field in iqs269_ver_info now
contains useful information; give it a name (fw_num).
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/ZZMaT46WQq1/Nrsb@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit ae42f92888 ("gpio: Return EPROBE_DEFER if gc->to_irq is NULL")
make gpiod_to_irq() possible to return -EPROBE_DEFER when the racing
happens. This causes the following error message to be printed:
gpio-keys gpio_keys: Unable to get irq number for GPIO 0, error -517
Fix that by changing dev_err() to dev_err_probe()
Signed-off-by: Hermes Zhang <chenhuiz@axis.com>
Link: https://lore.kernel.org/r/20231229013657.692600-1-Hermes.Zhang@axis.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- a quirk to AT keyboard driver to skip issuing "GET ID" command when
8042 is in translated mode and the device is a laptop/portable,
because the "GET ID" command makes a bunch of recent laptops unhappy
- a quirk to i8042 to disable multiplexed mode on Acer P459-G2-M which
causes issues on resume
- psmouse will activate native RMI4 protocol support for touchpad on
ThinkPad L14 G1
- addition of Razer Wolverine V2 ID to xpad gamepad driver
- mapping for airplane mode button in soc_button_array driver for
TUXEDO laptops
- improved error handling in ipaq-micro-keys driver
- amimouse being prepared for platform remove callback returning void
* tag 'input-for-v6.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: soc_button_array - add mapping for airplane mode button
Input: xpad - add Razer Wolverine V2 support
Input: ipaq-micro-keys - add error handling for devm_kmemdup
Input: amimouse - convert to platform remove callback returning void
Input: i8042 - add nomux quirk for Acer P459-G2-M
Input: atkbd - skip ATKBD_CMD_GETID in translated mode
Input: psmouse - enable Synaptics InterTouch for ThinkPad L14 G1
This add a mapping for the airplane mode button on the TUXEDO Pulse Gen3.
While it is physically a key it behaves more like a switch, sending a key
down on first press and a key up on 2nd press. Therefor the switch event
is used here. Besides this behaviour it uses the HID usage-id 0xc6
(Wireless Radio Button) and not 0xc8 (Wireless Radio Slider Switch), but
since neither 0xc6 nor 0xc8 are currently implemented at all in
soc_button_array this not to standard behaviour is not put behind a quirk
for the moment.
Signed-off-by: Christoffer Sandberg <cs@tuxedo.de>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://lore.kernel.org/r/20231215171718.80229-1-wse@tuxedocomputers.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In order to introduce a pwm api which can be used from atomic context,
we will need two functions for applying pwm changes:
int pwm_apply_might_sleep(struct pwm *, struct pwm_state *);
int pwm_apply_atomic(struct pwm *, struct pwm_state *);
This commit just deals with renaming pwm_apply_state(), a following
commit will introduce the pwm_apply_atomic() function.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> # for input
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Simplify probe() by replacing of_match_node() for retrieving match data by
device_get_match_data().
Some minor cleanups:
* Remove the trailing comma in the terminator entry for the OF
table making code robust against (theoretical) misrebases or other
similar things where the new entry goes _after_ the termination without
the compiler noticing.
* Move OF table near to the user.
* Arrange variables in reverse xmas tree order in probe().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20231213214803.9931-2-biju.das.jz@bp.renesas.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver supports passing some GPIO lines for rows and columns
through the driver data, but there is no in-kernel user of this.
Further the use seems convoluted because the GPIO lines are unused
in the driver, then explicitly free:ed when removing it without
being requested when probing it, which is assymetric and just
a recepie for disaster.
Remove the support for these unused GPIOs, if need be support can
be reestablished in an organized fashion using GPIO descriptors.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20231129-descriptors-input-v1-3-9433162914a3@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rename min_buffers_needed into min_queued_buffers and update
the documentation about it.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: Drop the change where min_queued_buffers + 1 buffers would be]
[hverkuil: allocated. Now this patch only renames this field instead of making]
[hverkuil: a functional change as well.]
[hverkuil: Renamed 3 remaining min_buffers_needed occurrences.]
Add the needed device-tree compatible strings to the MAX77693 haptic
driver, so it can be automatically loaded when compiled as a kernel
module and given device-tree contains separate (i.e. 'motor-driver') node
under the main PMIC node. When device is instantiated from device-tree,
the driver data cannot be read via platform_get_device_id(), so get
device type from the parent MFD device instead, what works for both
cases.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231006100320.2908210-1-m.szyprowski@samsung.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The cap11xx devices have three hardware identification registers which are
currently marked as volatile, preventing caching of those registers. This
is not ideal since the registers should never change at runtime, we should
be able to cache the value after the first read. Stop marking the registers
as volatile, we don't have register defaults specified in the driver so
this will result in reading from the hardware on first use.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20231001-input-maple-v1-1-ed3716051431@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
