Chips which use the IP discovery firmware loaded by the driver
reported incorrect harvesting information in the ip discovery
table in sysfs because the driver only uses the ip discovery
firmware for populating sysfs and not for direct parsing for the
driver itself as such, the fields that are used to print the
harvesting info in sysfs report incorrect data for some IPs. Populate
the relevant fields for this case as well.
Fixes: 514678da56 ("drm/amdgpu/discovery: fix fw based ip discovery")
Acked-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The Constant Engine found on gfx6-gfx10 HW has been a notorious source of
problems.
RADV never used it in the first place, radeonsi only used it for a few
releases around 2017 for gfx6-gfx9 before dropping support for it as
well.
While investigating another problem I just recently found that submitting
to the CE seems to be completely broken on gfx9 for quite a while.
Since nobody complained about that problem it most likely means that
nobody is using any of the affected radeonsi versions on current Linux
kernels any more.
So to potentially phase out the support for the CE and eliminate another
source of problems block submitting CE IBs unless it is enabled again
using a debug flag.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enabling ASPM causes randoms hangs on Tahiti and Oland on Zen4.
It's unclear if this is a platform-specific or GPU-specific issue.
Disable ASPM on SI for the time being.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On various SI GPUs, a flickering can be observed near the bottom
edge of the screen when using a single 4K 60Hz monitor over DP.
Disabling MCLK switching works around this problem.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
intel_frontbuffer_get() is what locks out subsequent set_tiling
changes to the bo. Thus the fence vs. modifier check must be done
after intel_frontbuffer_get(), or else a concurrent set_tiling ioctl
might sneak in and change the fence after the check has been done.
Close the race again. See commit dd689287b9 ("drm/i915: Prevent
concurrent tiling/framebuffer modifications") for the previous
instance.
v2: Reorder intel_user_framebuffer_destroy() to match the unwind (Jani)
Cc: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Fixes: 10690b8a49 ("drm/i915/display: Add intel_fb_bo_framebuffer_fini")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20251003145734.7634-3-ville.syrjala@linux.intel.com
(cherry picked from commit 1d1e4ded21)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Currently xe's intel_frontbuffer implementation forgets to
hold a reference on the bo. This makes the entire thing
extremely fragile as the cleanup order now depends on bo
references held by other things
(namely intel_fb_bo_framebuffer_fini()).
Move the bo refcounting to intel_frontbuffer_{get,release}()
so that both i915 and xe do this the same way.
I first tried to fix this by having xe do the refcounting
from its intel_bo_set_frontbuffer() implementation
(which is what i915 does currently), but turns out xe's
drm_gem_object_free() can sleep and thus drm_gem_object_put()
isn't safe to call while we hold fb_tracking.lock.
Fixes: 10690b8a49 ("drm/i915/display: Add intel_fb_bo_framebuffer_fini")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20251003145734.7634-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit eb4d490729)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
There is now a new LT9211 rev. U5, which reports chip ID 0x18 0x01 0xe4 .
The previous LT9211 reported chip ID 0x18 0x01 0xe3 , which is what the
driver checks for right now. Since there is a possibility there will be
yet another revision of the LT9211 in the future, drop the last version
nibble check to allow all future revisions of the chip to work with this
driver.
This fix makes LT9211 rev. U5 work with this driver.
Fixes: 8ce4129e3d ("drm/bridge: lt9211: Add Lontium LT9211 bridge driver")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251011110017.12521-1-marek.vasut@mailbox.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Pull more drm fixes from Dave Airlie:
"Just the follow up fixes for rc1 from the next branch, amdgpu and xe
mostly with a single v3d fix in there.
amdgpu:
- DC DCE6 fixes
- GPU reset fixes
- Secure diplay messaging cleanup
- MES fix
- GPUVM locking fixes
- PMFW messaging cleanup
- PCI US/DS switch handling fix
- VCN queue reset fix
- DC FPU handling fix
- DCN 3.5 fix
- DC mirroring fix
amdkfd:
- Fix kfd process ref leak
- mmap write lock handling fix
- Fix comments in IOCTL
xe:
- Fix build with clang 16
- Fix handling of invalid configfs syntax usage and spell out the
expected syntax in the documentation
- Do not try late bind firmware when running as VF since it shouldn't
handle firmware loading
- Fix idle assertion for local BOs
- Fix uninitialized variable for late binding
- Do not require perfmon_capable to expose free memory at page
granularity. Handle it like other drm drivers do
- Fix lock handling on suspend error path
- Fix I2C controller resume after S3
v3d:
- fix fence locking"
* tag 'drm-next-2025-10-11-1' of https://gitlab.freedesktop.org/drm/kernel: (34 commits)
drm/amd/display: Incorrect Mirror Cositing
drm/amd/display: Enable Dynamic DTBCLK Switch
drm/amdgpu: Report individual reset error
drm/amdgpu: partially revert "revert to old status lock handling v3"
drm/amd/display: Fix unsafe uses of kernel mode FPU
drm/amd/pm: Disable VCN queue reset on SMU v13.0.6 due to regression
drm/amdgpu: Fix general protection fault in amdgpu_vm_bo_reset_state_machine
drm/amdgpu: Check swus/ds for switch state save
drm/amdkfd: Fix two comments in kfd_ioctl.h
drm/amd/pm: Avoid interface mismatch messaging
drm/amdgpu: Merge amdgpu_vm_set_pasid into amdgpu_vm_init
drm/amd/amdgpu: Fix the mes version that support inv_tlbs
drm/amd: Check whether secure display TA loaded successfully
drm/amdkfd: Fix mmap write lock not release
drm/amdkfd: Fix kfd process ref leaking when userptr unmapping
drm/amdgpu: Fix for GPU reset being blocked by KIQ I/O.
drm/amd/display: Disable scaling on DCE6 for now
drm/amd/display: Properly disable scaling on DCE6
drm/amd/display: Properly clear SCL_*_FILTER_CONTROL on DCE6
drm/amd/display: Add missing DCE6 SCL_HORZ_FILTER_INIT* SRIs
...
Pull drm fixes from Dave Airlie:
"Some fixes leftover from our fixes branch, just nouveau and vmwgfx:
nouveau:
- Return errno code from TTM move helper
vmwgfx:
- Fix null-ptr access in cursor code
- Fix UAF in validation
- Use correct iterator in validation"
* tag 'drm-fixes-2025-10-11' of https://gitlab.freedesktop.org/drm/kernel:
drm/nouveau: fix bad ret code in nouveau_bo_move_prep
drm/vmwgfx: Fix copy-paste typo in validation
drm/vmwgfx: Fix Use-after-free in validation
drm/vmwgfx: Fix a null-ptr access in the cursor snooper
Currently the Panthor driver needs the GPU to be powered down
between suspend and resume. If this is not done, then the
MCU_CONTROL register will be preserved as AUTO, which again will
cause a premature FW boot on resume. The FW will go directly into
fatal state in this case.
This case needs to be handled as there is no guarantee that the
GPU will be powered down after the suspend callback on all platforms.
The fix is to call panthor_fw_stop() in "pre-reset" path to ensure
the MCU_CONTROL register is cleared (set DISABLE). This matches
well with the already existing call to panthor_fw_start() from the
"post-reset" path.
Signed-off-by: Ketil Johnsen <ketil.johnsen@arm.com>
Acked-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Fixes: 2718d91816 ("drm/panthor: Add the FW logical block")
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20251008105112.4077015-1-ketil.johnsen@arm.com
In `nouveau_bo_move_prep`, if `nouveau_mem_map` fails, an error code
should be returned. Currently, it returns zero even if vmm addr is not
correctly mapped.
Cc: stable@vger.kernel.org
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Shuhao Fu <sfual@cse.ust.hk>
Fixes: 9ce523cc3b ("drm/nouveau: separate buffer object backing memory from nvkm structures")
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
If reinitialization of one of the GPUs fails after reset, it logs
failure on all subsequent GPUs eventhough they have resumed
successfully.
A sample log where only device at 0000:95:00.0 had a failure -
amdgpu 0000:15:00.0: amdgpu: GPU reset(19) succeeded!
amdgpu 0000:65:00.0: amdgpu: GPU reset(19) succeeded!
amdgpu 0000:75:00.0: amdgpu: GPU reset(19) succeeded!
amdgpu 0000:85:00.0: amdgpu: GPU reset(19) succeeded!
amdgpu 0000:95:00.0: amdgpu: GPU reset(19) failed
amdgpu 0000:e5:00.0: amdgpu: GPU reset(19) failed
amdgpu 0000:f5:00.0: amdgpu: GPU reset(19) failed
amdgpu 0000:05:00.0: amdgpu: GPU reset(19) failed
amdgpu 0000:15:00.0: amdgpu: GPU reset end with ret = -5
To avoid confusion, report the error for each device
separately and return the first error as the overall result.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The CI systems are pointing out list corruptions, so we still need to
fix something here.
Keep the asserts, but revert the lock changes for now.
Fixes: 59e4405e9e ("drm/amdgpu: revert to old status lock handling v3")
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The point of isolating code that uses kernel mode FPU in separate
compilation units is to ensure that even implicit uses of, e.g., SIMD
registers for spilling occur only in a context where this is permitted,
i.e., from inside a kernel_fpu_begin/end block.
This is important on arm64, which uses -mgeneral-regs-only to build all
kernel code, with the exception of such compilation units where FP or
SIMD registers are expected to be used. Given that the compiler may
invent uses of FP/SIMD anywhere in such a unit, none of its code may be
accessible from outside a kernel_fpu_begin/end block.
This means that all callers into such compilation units must use the
DC_FP start/end macros, which must not occur there themselves. For
robustness, all functions with external linkage that reside there should
call dc_assert_fp_enabled() to assert that the FPU context was set up
correctly.
Fix this for the DCN35, DCN351 and DCN36 implementations.
Cc: Austin Zheng <austin.zheng@amd.com>
Cc: Jun Lei <jun.lei@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Rodrigo Siqueira <siqueira@igalia.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disable VCN reset capability for the program 4 as it's
causing regressions.
Fixes: 9d20f37a10 ("drm/amd/pm: Add VCN reset support for SMU v13.0.6")
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Jesse Zhang <jesse.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
PMFW interface version is not used by some IP implementations like SMU
v13.0.6/12, instead rely on PMFW version checks. Avoid the log if
interface version is not used.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As KFD no longer uses a separate PASID, the global amdgpu_vm_set_pasid()function is no longer necessary.
Merge its functionality directly intoamdgpu_vm_init() to simplify code flow and eliminate redundant locking.
v2: remove superflous check
adjust amdgpu_vm_fin and remove amdgpu_vm_set_pasid (Chritian)
v3: drop amdgpu_vm_assert_locked (Chritian)
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4614
Fixes: 59e4405e9e ("drm/amdgpu: revert to old status lock handling v3")
Reviewed-by: Christian König <christian.koenig@amd.com>
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
MES version 0x83 is not stable to use the inv_tlbs API. Defer it to 0x84 vertsion.
Fixes: 85442bac84 ("drm/amd/amdgpu: Fix the mes version that support inv_tlbs")
Signed-off-by: Shaoyun Liu <shaoyun.liu@amd.com>
Reviewed-by: Michael Chen <michael.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Not all renoir hardware supports secure display. If the TA is present
but the feature isn't supported it will fail to load or send commands.
This shows ERR messages to the user that make it seems like there is
a problem.
[How]
Check the resp_status of the context to see if there was an error
before trying to send any secure display commands.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/1415
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If mmap write lock is taken while draining retry fault, mmap write lock
is not released because svm_range_restore_pages calls mmap_read_unlock
then returns. This causes deadlock and system hangs later because mmap
read or write lock cannot be taken.
Downgrade mmap write lock to read lock if draining retry fault fix this
bug.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
kfd_lookup_process_by_pid hold the kfd process reference to ensure it
doesn't get destroyed while sending the segfault event to user space.
Calling kfd_lookup_process_by_pid as function parameter leaks the kfd
process refcount and miss the NULL pointer check if app process is
already destroyed.
Fixes: 2d274bf709 ("amd/amdkfd: Trigger segfault for early userptr unmmapping")
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is some probability that reset workqueue is blocked by KIQ I/O for 10+ seconds after gpu hangs.
So we need to add a in_reset check during each KIQ register poll.
Signed-off-by: Heng Zhou <Heng.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Scaling doesn't work on DCE6 at the moment, the current
register programming produces incorrect output when using
fractional scaling (between 100-200%) on resolutions higher
than 1080p.
Disable it until we figure out how to program it properly.
Fixes: 7c15fd86aa ("drm/amd/display: dc/dce: add initial DCE6 support (v10)")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SCL_SCALER_ENABLE can be used to enable/disable the scaler
on DCE6. Program it to 0 when scaling isn't used, 1 when used.
Additionally, clear some other registers when scaling is
disabled and program the SCL_UPDATE register as recommended.
This fixes visible glitches for users whose BIOS sets up a
mode with scaling at boot, which DC was unable to clean up.
Fixes: b70aaf5586 ("drm/amd/display: dce_transform: add DCE6 specific macros,functions")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Previously, the code would set a bit field which didn't exist
on DCE6 so it would be effectively a no-op.
Fixes: b70aaf5586 ("drm/amd/display: dce_transform: add DCE6 specific macros,functions")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull hyperv updates from Wei Liu:
- Unify guest entry code for KVM and MSHV (Sean Christopherson)
- Switch Hyper-V MSI domain to use msi_create_parent_irq_domain()
(Nam Cao)
- Add CONFIG_HYPERV_VMBUS and limit the semantics of CONFIG_HYPERV
(Mukesh Rathor)
- Add kexec/kdump support on Azure CVMs (Vitaly Kuznetsov)
- Deprecate hyperv_fb in favor of Hyper-V DRM driver (Prasanna
Kumar T S M)
- Miscellaneous enhancements, fixes and cleanups (Abhishek Tiwari,
Alok Tiwari, Nuno Das Neves, Wei Liu, Roman Kisel, Michael Kelley)
* tag 'hyperv-next-signed-20251006' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hyperv: Remove the spurious null directive line
MAINTAINERS: Mark hyperv_fb driver Obsolete
fbdev/hyperv_fb: deprecate this in favor of Hyper-V DRM driver
Drivers: hv: Make CONFIG_HYPERV bool
Drivers: hv: Add CONFIG_HYPERV_VMBUS option
Drivers: hv: vmbus: Fix typos in vmbus_drv.c
Drivers: hv: vmbus: Fix sysfs output format for ring buffer index
Drivers: hv: vmbus: Clean up sscanf format specifier in target_cpu_store()
x86/hyperv: Switch to msi_create_parent_irq_domain()
mshv: Use common "entry virt" APIs to do work in root before running guest
entry: Rename "kvm" entry code assets to "virt" to genericize APIs
entry/kvm: KVM: Move KVM details related to signal/-EINTR into KVM proper
mshv: Handle NEED_RESCHED_LAZY before transferring to guest
x86/hyperv: Add kexec/kdump support on Azure CVMs
Drivers: hv: Simplify data structures for VMBus channel close message
Drivers: hv: util: Cosmetic changes for hv_utils_transport.c
mshv: Add support for a new parent partition configuration
clocksource: hyper-v: Skip unnecessary checks for the root partition
hyperv: Add missing field to hv_output_map_device_interrupt
Cross-subsystem Changes:
- Fix userptr to not allow device private pages with SVM (Thomas
Hellström)
Driver Changes:
- Fix build with clang 16 (Michal Wajdeczko)
- Fix handling of invalid configfs syntax usage and spell out the
expected syntax in the documentation (Lucas De Marchi)
- Do not try late bind firmware when running as VF since it
shouldn't handle firmware loading (Michal Wajdeczko)
- Fix idle assertion for local BOs (Thomas Hellström)
- Fix uninitialized variable for late binding (Colin Ian King,
Mallesh Koujalagi)
- Do not require perfmon_capable to expose free memory at page
granularity. Handle it like other drm drivers do (Matthew Auld)
- Fix lock handling on suspend error path (Shuicheng Lin)
- Fix I2C controller resume after S3 (Raag Jadav)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/q6yeyb7n2eqo5megxjqayooajirx5hhsntfo65m3y4myscz7oz@25qbabbbr4hj
Check that the resource which is converted to a surface exists before
trying to use the cursor snooper on it.
vmw_cmd_res_check allows explicit invalid (SVGA3D_INVALID_ID) identifiers
because some svga commands accept SVGA3D_INVALID_ID to mean "no surface",
unfortunately functions that accept the actual surfaces as objects might
(and in case of the cursor snooper, do not) be able to handle null
objects. Make sure that we validate not only the identifier (via the
vmw_cmd_res_check) but also check that the actual resource exists before
trying to do something with it.
Fixes unchecked null-ptr reference in the snooping code.
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Fixes: c0951b797e ("drm/vmwgfx: Refactor resource management")
Reported-by: Kuzey Arda Bulut <kuzeyardabulut@gmail.com>
Cc: Broadcom internal kernel review list <bcm-kernel-feedback-list@broadcom.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Ian Forbes <ian.forbes@broadcom.com>
Link: https://lore.kernel.org/r/20250917153655.1968583-1-zack.rusin@broadcom.com
In xe_hw_engine_group_get_mode(), a write lock is acquired before
calling switch_mode(), which in turn invokes
xe_hw_engine_group_suspend_faulting_lr_jobs().
On failure inside xe_hw_engine_group_suspend_faulting_lr_jobs(),
the write lock is released there, and then again in
xe_hw_engine_group_get_mode(), leading to a double release.
Fix this by keeping both acquire and release operation in
xe_hw_engine_group_get_mode().
Fixes: 770bd1d341 ("drm/xe/hw_engine_group: Ensure safe transition between execution modes")
Cc: Francois Dugast <francois.dugast@intel.com>
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
Reviewed-by: Francois Dugast <francois.dugast@intel.com>
Link: https://lore.kernel.org/r/20250925023145.1203004-2-shuicheng.lin@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit 662d98b8b3)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Currently this is hidden behind perfmon_capable() since this is
technically an info leak, given that this is a system wide metric.
However the granularity reported here is always PAGE_SIZE aligned, which
matches what the core kernel is already willing to expose to userspace
if querying how many free RAM pages there are on the system, and that
doesn't need any special privileges. In addition other drm drivers seem
happy to expose this.
The motivation here if with oneAPI where they want to use the system
wide 'used' reporting here, so not the per-client fdinfo stats. This has
also come up with some perf overlay applications wanting this
information.
Fixes: 1105ac15d2 ("drm/xe/uapi: restrict system wide accounting")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Joshua Santosh <joshua.santosh.ranjan@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: <stable@vger.kernel.org> # v6.8+
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250919122052.420979-2-matthew.auld@intel.com
(cherry picked from commit 4d0b035fd6)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Pull fs_context updates from Al Viro:
"Change vfs_parse_fs_string() calling conventions
Get rid of the length argument (almost all callers pass strlen() of
the string argument there), add vfs_parse_fs_qstr() for the cases that
do want separate length"
* tag 'pull-fs_context' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
do_nfs4_mount(): switch to vfs_parse_fs_string()
change the calling conventions for vfs_parse_fs_string()
Initialize the uval variable to 0 in xe_late_bind_fw_num_fans() to fix
a potential use of uninitialized variable warning and ensure predictable
behavior.
The variable is passed by reference to xe_pcode_read() which should
populate it on success, but initializing it to 0 provides a safe
default value and follows kernel coding best practices.
v2:
- uval = 0 which serves as both a safe default and the fallback
value when the pcode read operation fails.
v3:
- Handle MMIO failure (Rodrigo)
- The function should probably return the error and make the uval as
pointer-argument, like the pcode_read.
- Change the caller of this function to propagate the error
upwards if mmio failed.
Fixes: 45832bf9c1 ("drm/xe/xe_late_bind_fw: Initialize late binding firmware")
Signed-off-by: Mallesh Koujalagi <mallesh.koujalagi@intel.com>
Link: https://lore.kernel.org/r/20251002005648.3185636-1-mallesh.koujalagi@intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit 07abc16c14)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
