The ROHM BD79112 is an ADC/GPIO with 32 channels. The channel inputs can
be used as ADC or GPIO. Using the GPIOs as IRQ sources isn't supported.
The ADC is 12-bit, supporting input voltages up to 5.7V, and separate I/O
voltage supply. Maximum SPI clock rate is 20 MHz (10 MHz with
daisy-chain configuration) and maximum sampling rate is 1MSPS.
Add a device tree binding document for the ROHM BD79112.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use correct clocks properties for the AD7124 family of ADCs.
These ADCs have an internal clock along with an optional external clock
that can be connected to the CLK pin. This pin can be wired up 3 ways:
1. Not connected - the internal clock is used.
2. Connected to an external clock (input) - the external clock is used.
3. Connected to the CLK pin on another ADC (output) - the internal clock
is used on one and the other is configured for an external clock.
The new bindings describe these 3 cases by picking one of the following:
1. Omit both clocks and #clock-cells properties.
2. Include only the clocks property with a phandle to the external clock.
3. Include only the #clock-cells property on the ADC providing the output.
The clock-names property is now deprecated and should not be used. The
MCLK signal that it refers to is an internal counter in the ADC and
therefore does not make sense as a devicetree property as it can't be
connected to anything external to the ADC. Since there is only one
possible external clock, the clock-names property is not needed anyway.
Based on the implementation of the Linux driver, it looks like the
"mclk" clock was basically being used as a control to select the power
mode of the ADC, which is not something that should be done in the
devicetree.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250828-iio-adc-ad7124-proper-clock-support-v3-1-0b317b4605e5@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add microchip,mcp9601 compatible in addition to the original
microchip,mcp9600 to designate support between these two chips.
The current dt-binding has open-circuit and short-circuit as interrupt
names, but these are only supported in mcp9601.
The OC and SC detection requires that mcp9601 VSENSE be wired up, which
not only enables the OC SC interrupts, but also the OC and SC status
register bits.
Add a microchip,vsense boolean to show the chip is wired for this
support.
Add constraints so this feature only applies if the mcp9601 compatible
is selected.
Signed-off-by: Ben Collins <bcollins@watter.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250822-upstream-changes-v8-2-40bb1739e3e2@watter.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BD79105 is a simple, 16-bit, 1-channel ADC with a 'CONVSTART'
pin used to start the ADC conversion. Other than the 'CONVSTART', there
are 3 supply pins (one used as a reference), analog inputs, ground and
communication pins. It's worth noting that the pin somewhat confusingly
labeled as 'DIN', is a pin which should be used as a chip-select. The IC
does not have any writable registers.
The device is designed so that the output pin can, in addition to
outputting the data, be used as a 'data-ready'-IRQ. There are cases
where the IRQ can't be used (because it is delivered via SPI data-line).
Hence, some systems may use a GPIO for polling the data readiness.
Add a compatible for the bd79105 and add the data-ready GPIO to the
binding.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/3f70f68665225be3091f8a0412e74037b6a2a88e.1754901948.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The SARADC controller in most Rockchip SoCs are part of power domains
that are always powered on, i.e. PD_BUS or PD_PERI. These always powered
on power domains have typically not been described in the device tree.
Because these power domains have been left out of the device tree there
has not been any real need to properly describe the power domain of the
SARADC controller.
On RK3528 the SARADC controller is part of the PD_VPU power domain.
Add support to describe an optional power-domains for the SARADC
controller in Rockchip SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250723085654.2273324-4-jonas@kwiboo.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull char / misc / IIO / other driver updates from Greg KH:
"Here is the big set of char/misc/iio and other smaller driver
subsystems for 6.17-rc1. It's a big set this time around, with the
huge majority being in the iio subsystem with new drivers and dts
files being added there.
Highlights include:
- IIO driver updates, additions, and changes making more code const
and cleaning up some init logic
- bus_type constant conversion changes
- misc device test functions added
- rust miscdevice minor fixup
- unused function removals for some drivers
- mei driver updates
- mhi driver updates
- interconnect driver updates
- Android binder updates and test infrastructure added
- small cdx driver updates
- small comedi fixes
- small nvmem driver updates
- small pps driver updates
- some acrn virt driver fixes for printk messages
- other small driver updates
All of these have been in linux-next with no reported issues"
* tag 'char-misc-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
binder: Use seq_buf in binder_alloc kunit tests
binder: Add copyright notice to new kunit files
misc: ti_fpc202: Switch to of_fwnode_handle()
bus: moxtet: Use dev_fwnode()
pc104: move PC104 option to drivers/Kconfig
drivers: virt: acrn: Don't use %pK through printk
comedi: fix race between polling and detaching
interconnect: qcom: Add Milos interconnect provider driver
dt-bindings: interconnect: document the RPMh Network-On-Chip Interconnect in Qualcomm Milos SoC
mei: more prints with client prefix
mei: bus: use cldev in prints
bus: mhi: host: pci_generic: Add Telit FN990B40 modem support
bus: mhi: host: Detect events pointing to unexpected TREs
bus: mhi: host: pci_generic: Add Foxconn T99W696 modem
bus: mhi: host: Use str_true_false() helper
bus: mhi: host: pci_generic: Add support for EM929x and set MRU to 32768 for better performance.
bus: mhi: host: Fix endianness of BHI vector table
bus: mhi: host: pci_generic: Disable runtime PM for QDU100
bus: mhi: host: pci_generic: Fix the modem name of Foxconn T99W640
dt-bindings: interconnect: qcom,msm8998-bwmon: Allow 'nonposted-mmio'
...
Fix following dt_schema warning when offload is used:
DTC [C] arch/arm/boot/dts/xilinx/zynq-zed-adv7511-ad7606.dtb
/home/angelo/dev-baylibre/linux-iio/arch/arm/boot/dts/xilinx/zynq-zed-adv7511-ad7606.dtb: adc@0: 'oneOf' conditional failed, one must be fixed:
'interrupts' is a required property
'io-backends' is a required property
from schema $id: http://devicetree.org/schemas/iio/adc/adi,ad7606.yaml#
There isn't any reason that we couldn't have interrupts wired up at the
same time we are using io-backends or SPI offload, so dropping off the
related "oneOf" block entirely.
Fixes: 81fe5529e8 ("dt-bindings: iio: adc: adi,ad7606: add SPI offload properties")
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20250526-wip-bl-ad7606-dtschema-fixes-v2-1-9bd56d039489@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In addition to GPIO synchronization, The AD7768-1 also supports
synchronization over SPI, which use is recommended when the GPIO
cannot provide a pulse synchronous with the base MCLK signal. It
consists of looping back the SYNC_OUT to the SYNC_IN pin and send
a command via SPI to trigger the synchronization.
Introduce the 'trigger-sources' property to enable SPI-based
synchronization via SYNC_OUT pin, along with additional optional
entries for GPIO3 and DRDY pins.
Also create #trigger-source-cells property to differentiate the trigger
sources provided by the ADC. To improve readability, create a
adi,ad7768-1.h header with the macros for the cell values.
While at it, add description to the interrupts property.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: David Lechner <dlechner@baylirbe.com>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Link: https://patch.msgid.link/713fd786010c75858700efaec8bb285274e7057e.1749569957.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a new compatible and related bindings for the fpga-based
AD408x AXI IP core, a variant of the generic AXI ADC IP.
The AXI AD408x IP is a very similar HDL (fpga) variant of the
generic AXI ADC IP, intended to control ad408x familiy.
Although there are some particularities added for extended
control of the ad408x devices such as the filter configuration.
Wildcard naming is used to match the naming of the published
firmware.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250516082630.8236-5-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull char / misc / iio driver updates from Greg KH:
"Here is the big char/misc/iio and other small driver subsystem pull
request for 6.16-rc1.
Overall, a lot of individual changes, but nothing major, just the
normal constant forward progress of new device support and cleanups to
existing subsystems. Highlights in here are:
- Large IIO driver updates and additions and device tree changes
- Android binder bugfixes and logfile fixes
- mhi driver updates
- comedi driver updates
- counter driver updates and additions
- coresight driver updates and additions
- echo driver removal as there are no in-kernel users of it
- nvmem driver updates
- spmi driver updates
- new amd-sbi driver "subsystem" and drivers added
- rust miscdriver binding documentation fix
- other small driver fixes and updates (uio, w1, acrn, hpet,
xillybus, cardreader drivers, fastrpc and others)
All of these have been in linux-next for quite a while with no
reported problems"
* tag 'char-misc-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (390 commits)
binder: fix yet another UAF in binder_devices
counter: microchip-tcb-capture: Add watch validation support
dt-bindings: iio: adc: Add ROHM BD79100G
iio: adc: add support for Nuvoton NCT7201
dt-bindings: iio: adc: add NCT7201 ADCs
iio: chemical: Add driver for SEN0322
dt-bindings: trivial-devices: Document SEN0322
iio: adc: ad7768-1: reorganize driver headers
iio: bmp280: zero-init buffer
iio: ssp_sensors: optimalize -> optimize
HID: sensor-hub: Fix typo and improve documentation
iio: admv1013: replace redundant ternary operator with just len
iio: chemical: mhz19b: Fix error code in probe()
iio: adc: at91-sama5d2: use IIO_DECLARE_BUFFER_WITH_TS
iio: accel: sca3300: use IIO_DECLARE_BUFFER_WITH_TS
iio: adc: ad7380: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: adc: ad4695: rename AD4695_MAX_VIN_CHANNELS
iio: adc: ad4695: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: introduce IIO_DECLARE_BUFFER_WITH_TS macros
iio: make IIO_DMA_MINALIGN minimum of 8 bytes
...
Document the AD3530/AD3530R (8-channel) and AD3531/AD3531R (4-channel)
low-power, 16-bit, buffered voltage output DACs with software-
programmable gain controls. They provide full-scale output spans of 2.5V
or 5V for reference voltages of 2.5V. These devices operate on a single
2.7V to 5.5V supply and are guaranteed to be monotonic by design.
The "R" variants include a 2.5V, 5ppm/°C internal reference, which is
disabled by default.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Kim Seer Paller <kimseer.paller@analog.com>
Link: https://patch.msgid.link/20250429-togreg-v7-2-0af9c543b545@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
