Since the introduction of the subflow ULP diag interface, the
dump callback accessed all the subflow data with lockless.
We need either to annotate all the read and write operation accordingly,
or acquire the subflow socket lock. Let's do latter, even if slower, to
avoid a diffstat havoc.
Fixes: 5147dfb508 ("mptcp: allow dumping subflow context to userspace")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change, generation of the list of MDB events to replay
would race against the creation of new group memberships, either from
the IGMP/MLD snooping logic or from user configuration.
While new memberships are immediately visible to walkers of
br->mdb_list, the notification of their existence to switchdev event
subscribers is deferred until a later point in time. So if a replay
list was generated during a time that overlapped with such a window,
it would also contain a replay of the not-yet-delivered event.
The driver would thus receive two copies of what the bridge internally
considered to be one single event. On destruction of the bridge, only
a single membership deletion event was therefore sent. As a
consequence of this, drivers which reference count memberships (at
least DSA), would be left with orphan groups in their hardware
database when the bridge was destroyed.
This is only an issue when replaying additions. While deletion events
may still be pending on the deferred queue, they will already have
been removed from br->mdb_list, so no duplicates can be generated in
that scenario.
To a user this meant that old group memberships, from a bridge in
which a port was previously attached, could be reanimated (in
hardware) when the port joined a new bridge, without the new bridge's
knowledge.
For example, on an mv88e6xxx system, create a snooping bridge and
immediately add a port to it:
root@infix-06-0b-00:~$ ip link add dev br0 up type bridge mcast_snooping 1 && \
> ip link set dev x3 up master br0
And then destroy the bridge:
root@infix-06-0b-00:~$ ip link del dev br0
root@infix-06-0b-00:~$ mvls atu
ADDRESS FID STATE Q F 0 1 2 3 4 5 6 7 8 9 a
DEV:0 Marvell 88E6393X
33:33:00:00:00:6a 1 static - - 0 . . . . . . . . . .
33:33:ff:87:e4:3f 1 static - - 0 . . . . . . . . . .
ff:ff:ff:ff:ff:ff 1 static - - 0 1 2 3 4 5 6 7 8 9 a
root@infix-06-0b-00:~$
The two IPv6 groups remain in the hardware database because the
port (x3) is notified of the host's membership twice: once via the
original event and once via a replay. Since only a single delete
notification is sent, the count remains at 1 when the bridge is
destroyed.
Then add the same port (or another port belonging to the same hardware
domain) to a new bridge, this time with snooping disabled:
root@infix-06-0b-00:~$ ip link add dev br1 up type bridge mcast_snooping 0 && \
> ip link set dev x3 up master br1
All multicast, including the two IPv6 groups from br0, should now be
flooded, according to the policy of br1. But instead the old
memberships are still active in the hardware database, causing the
switch to only forward traffic to those groups towards the CPU (port
0).
Eliminate the race in two steps:
1. Grab the write-side lock of the MDB while generating the replay
list.
This prevents new memberships from showing up while we are generating
the replay list. But it leaves the scenario in which a deferred event
was already generated, but not delivered, before we grabbed the
lock. Therefore:
2. Make sure that no deferred version of a replay event is already
enqueued to the switchdev deferred queue, before adding it to the
replay list, when replaying additions.
Fixes: 4f2673b3a2 ("net: bridge: add helper to replay port and host-joined mdb entries")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from Jakub Kicinski:
"Including fixes from can, wireless and netfilter.
Current release - regressions:
- af_unix: fix task hung while purging oob_skb in GC
- pds_core: do not try to run health-thread in VF path
Current release - new code bugs:
- sched: act_mirred: don't zero blockid when net device is being
deleted
Previous releases - regressions:
- netfilter:
- nat: restore default DNAT behavior
- nf_tables: fix bidirectional offload, broken when unidirectional
offload support was added
- openvswitch: limit the number of recursions from action sets
- eth: i40e: do not allow untrusted VF to remove administratively set
MAC address
Previous releases - always broken:
- tls: fix races and bugs in use of async crypto
- mptcp: prevent data races on some of the main socket fields, fix
races in fastopen handling
- dpll: fix possible deadlock during netlink dump operation
- dsa: lan966x: fix crash when adding interface under a lag when some
of the ports are disabled
- can: j1939: prevent deadlock by changing j1939_socks_lock to rwlock
Misc:
- a handful of fixes and reliability improvements for selftests
- fix sysfs documentation missing net/ in paths
- finish the work of squashing the missing MODULE_DESCRIPTION()
warnings in networking"
* tag 'net-6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (92 commits)
net: fill in MODULE_DESCRIPTION()s for missing arcnet
net: fill in MODULE_DESCRIPTION()s for mdio_devres
net: fill in MODULE_DESCRIPTION()s for ppp
net: fill in MODULE_DESCRIPTION()s for fddik/skfp
net: fill in MODULE_DESCRIPTION()s for plip
net: fill in MODULE_DESCRIPTION()s for ieee802154/fakelb
net: fill in MODULE_DESCRIPTION()s for xen-netback
net: ravb: Count packets instead of descriptors in GbEth RX path
pppoe: Fix memory leak in pppoe_sendmsg()
net: sctp: fix skb leak in sctp_inq_free()
net: bcmasp: Handle RX buffer allocation failure
net-timestamp: make sk_tskey more predictable in error path
selftests: tls: increase the wait in poll_partial_rec_async
ice: Add check for lport extraction to LAG init
netfilter: nf_tables: fix bidirectional offload regression
netfilter: nat: restore default DNAT behavior
netfilter: nft_set_pipapo: fix missing : in kdoc
igc: Remove temporary workaround
igb: Fix string truncation warnings in igb_set_fw_version
can: netlink: Fix TDCO calculation using the old data bittiming
...
Pull xen fixes from Juergen Gross:
"Fixes and simple cleanups:
- use a proper flexible array instead of a one-element array in order
to avoid array-bounds sanitizer errors
- add NULL pointer checks after allocating memory
- use memdup_array_user() instead of open-coding it
- fix a rare race condition in Xen event channel allocation code
- make struct bus_type instances const
- make kerneldoc inline comments match reality"
* tag 'for-linus-6.8a-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/events: close evtchn after mapping cleanup
xen/gntalloc: Replace UAPI 1-element array
xen: balloon: make balloon_subsys const
xen: pcpu: make xen_pcpu_subsys const
xen/privcmd: Use memdup_array_user() in alloc_ioreq()
x86/xen: Add some null pointer checking to smp.c
xen/xenbus: document will_handle argument for xenbus_watch_path()
In commit 4356e9f841 ("work around gcc bugs with 'asm goto' with
outputs") I did the gcc workaround unconditionally, because the cause of
the bad code generation wasn't entirely clear.
In the meantime, Jakub Jelinek debugged the issue, and has come up with
a fix in gcc [2], which also got backported to the still maintained
branches of gcc-11, gcc-12 and gcc-13.
Note that while the fix technically wasn't in the original gcc-14
branch, Jakub says:
"while it is true that no GCC 14 snapshots until today (or whenever the
fix will be committed) have the fix, for GCC trunk it is up to the
distros to use the latest snapshot if they use it at all and would
allow better testing of the kernel code without the workaround, so
that if there are other issues they won't be discovered years later.
Most userland code doesn't actually use asm goto with outputs..."
so we will consider gcc-14 to be fixed - if somebody is using gcc
snapshots of the gcc-14 before the fix, they should upgrade.
Note that while the bug goes back to gcc-11, in practice other gcc
changes seem to have effectively hidden it since gcc-12.1 as per a
bisect by Jakub. So even a gcc-14 snapshot without the fix likely
doesn't show actual problems.
Also, make the default 'asm_goto_output()' macro mark the asm as
volatile by hand, because of an unrelated gcc issue [1] where it doesn't
match the documented behavior ("asm goto is always volatile").
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=103979 [1]
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=113921 [2]
Link: https://lore.kernel.org/all/20240208220604.140859-1-seanjc@google.com/
Requested-by: Jakub Jelinek <jakub@redhat.com>
Cc: Uros Bizjak <ubizjak@gmail.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Sean Christopherson <seanjc@google.com>
Cc: Andrew Pinski <quic_apinski@quicinc.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull MIPS fixes from Thomas Bogendoerfer:
- Fix for broken ipv6 checksums
- Fix handling of exceptions in delay slots
* tag 'mips-fixes_6.8_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
mm/memory: Use exception ip to search exception tables
MIPS: Clear Cause.BD in instruction_pointer_set
ptrace: Introduce exception_ip arch hook
MIPS: Add 'memory' clobber to csum_ipv6_magic() inline assembler
Pull vfs fixes from Christian Brauner:
- Fix performance regression introduced by moving the security
permission hook out of do_clone_file_range() and into its caller
vfs_clone_file_range().
This causes the security hook to be called in situation were it
wasn't called before as the fast permission checks were left in
do_clone_file_range().
Fix this by merging the two implementations back together and
restoring the old ordering: fast permission checks first, expensive
ones later.
- Tweak mount_setattr() permission checking so that mount properties on
the real rootfs can be changed.
When we added mount_setattr() we added additional checks compared to
legacy mount(2). If the mount had a parent then verify that the
caller and the mount namespace the mount is attached to match and if
not make sure that it's an anonymous mount.
But the real rootfs falls into neither category. It is neither an
anoymous mount because it is obviously attached to the initial mount
namespace but it also obviously doesn't have a parent mount. So that
means legacy mount(2) allows changing mount properties on the real
rootfs but mount_setattr(2) blocks this. This causes regressions (See
the commit for details).
Fix this by relaxing the check. If the mount has a parent or if it
isn't a detached mount, verify that the mount namespaces of the
caller and the mount are the same. Technically, we could probably
write this even simpler and check that the mount namespaces match if
it isn't a detached mount. But the slightly longer check makes it
clearer what conditions one needs to think about.
* tag 'vfs-6.8-rc5.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
fs: relax mount_setattr() permission checks
remap_range: merge do_clone_file_range() into vfs_clone_file_range()
dev->lstats is notably used from loopback ndo_start_xmit()
and other virtual drivers.
Per cpu stats updates are dirtying per-cpu data,
but the pointer itself is read-only.
Fixes: 43a71cd66b ("net-device: reorganize net_device fast path variables")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Coco Li <lixiaoyan@google.com>
Cc: Simon Horman <horms@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer fix from Borislav Petkov:
- Make sure a warning is issued when a hrtimer gets queued after the
timers have been migrated on the CPU down path and thus said timer
will get ignored
* tag 'timers_urgent_for_v6.8_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hrtimer: Report offline hrtimer enqueue
The submitting thread (one which called recvmsg/sendmsg)
may exit as soon as the async crypto handler calls complete()
so any code past that point risks touching already freed data.
Try to avoid the locking and extra flags altogether.
Have the main thread hold an extra reference, this way
we can depend solely on the atomic ref counter for
synchronization.
Don't futz with reiniting the completion, either, we are now
tightly controlling when completion fires.
Reported-by: valis <sec@valis.email>
Fixes: 0cada33241 ("net/tls: fix race condition causing kernel panic")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- Update a potentially stale firmware attribute (Maurizio)
- Fixes for the recent verbose error logging (Keith, Chaitanya)
- Protection information payload size fix for passthrough (Francis)
- Fix for a queue freezing issue in virtblk (Yi)
- blk-iocost underflow fix (Tejun)
- blk-wbt task detection fix (Jan)
* tag 'block-6.8-2024-02-10' of git://git.kernel.dk/linux:
virtio-blk: Ensure no requests in virtqueues before deleting vqs.
blk-iocost: Fix an UBSAN shift-out-of-bounds warning
nvme: use ns->head->pi_size instead of t10_pi_tuple structure size
nvme-core: fix comment to reflect right functions
nvme: move passthrough logging attribute to head
blk-wbt: Fix detection of dirty-throttled tasks
nvme-host: fix the updating of the firmware version
Pull ceph fixes from Ilya Dryomov:
"Some fscrypt-related fixups (sparse reads are used only for encrypted
files) and two cap handling fixes from Xiubo and Rishabh"
* tag 'ceph-for-6.8-rc4' of https://github.com/ceph/ceph-client:
ceph: always check dir caps asynchronously
ceph: prevent use-after-free in encode_cap_msg()
ceph: always set initial i_blkbits to CEPH_FSCRYPT_BLOCK_SHIFT
libceph: just wait for more data to be available on the socket
libceph: rename read_sparse_msg_*() to read_partial_sparse_msg_*()
libceph: fail sparse-read if the data length doesn't match
We've had issues with gcc and 'asm goto' before, and we created a
'asm_volatile_goto()' macro for that in the past: see commits
3f0116c323 ("compiler/gcc4: Add quirk for 'asm goto' miscompilation
bug") and a9f180345f ("compiler/gcc4: Make quirk for
asm_volatile_goto() unconditional").
Then, much later, we ended up removing the workaround in commit
43c249ea0b ("compiler-gcc.h: remove ancient workaround for gcc PR
58670") because we no longer supported building the kernel with the
affected gcc versions, but we left the macro uses around.
Now, Sean Christopherson reports a new version of a very similar
problem, which is fixed by re-applying that ancient workaround. But the
problem in question is limited to only the 'asm goto with outputs'
cases, so instead of re-introducing the old workaround as-is, let's
rename and limit the workaround to just that much less common case.
It looks like there are at least two separate issues that all hit in
this area:
(a) some versions of gcc don't mark the asm goto as 'volatile' when it
has outputs:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=98619https://gcc.gnu.org/bugzilla/show_bug.cgi?id=110420
which is easy to work around by just adding the 'volatile' by hand.
(b) Internal compiler errors:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=110422
which are worked around by adding the extra empty 'asm' as a
barrier, as in the original workaround.
but the problem Sean sees may be a third thing since it involves bad
code generation (not an ICE) even with the manually added 'volatile'.
but the same old workaround works for this case, even if this feels a
bit like voodoo programming and may only be hiding the issue.
Reported-and-tested-by: Sean Christopherson <seanjc@google.com>
Link: https://lore.kernel.org/all/20240208220604.140859-1-seanjc@google.com/
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Uros Bizjak <ubizjak@gmail.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Cc: Andrew Pinski <quic_apinski@quicinc.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull EFI fixes from Ard Biesheuvel:
"The only notable change here is the patch that changes the way we deal
with spurious errors from the EFI memory attribute protocol. This will
be backported to v6.6, and is intended to ensure that we will not
paint ourselves into a corner when we tighten this further in order to
comply with MS requirements on signed EFI code.
Note that this protocol does not currently exist in x86 production
systems in the field, only in Microsoft's fork of OVMF, but it will be
mandatory for Windows logo certification for x86 PCs in the future.
- Tighten ELF relocation checks on the RISC-V EFI stub
- Give up if the new EFI memory attributes protocol fails spuriously
on x86
- Take care not to place the kernel in the lowest 16 MB of DRAM on
x86
- Omit special purpose EFI memory from memblock
- Some fixes for the CXL CPER reporting code
- Make the PE/COFF layout of mixed-mode capable images comply with a
strict interpretation of the spec"
* tag 'efi-fixes-for-v6.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
x86/efistub: Use 1:1 file:memory mapping for PE/COFF .compat section
cxl/trace: Remove unnecessary memcpy's
cxl/cper: Fix errant CPER prints for CXL events
efi: Don't add memblocks for soft-reserved memory
efi: runtime: Fix potential overflow of soft-reserved region size
efi/libstub: Add one kernel-doc comment
x86/efistub: Avoid placing the kernel below LOAD_PHYSICAL_ADDR
x86/efistub: Give up if memory attribute protocol returns an error
riscv/efistub: Tighten ELF relocation check
riscv/efistub: Ensure GP-relative addressing is not used
Pull drm fixes from Dave Airlie:
"Regular weekly fixes, xe, amdgpu and msm are most of them, with some
misc in i915, ivpu and nouveau, scattered but nothing too intense at
this point.
i915:
- gvt: docs fix, uninit var, MAINTAINERS
ivpu:
- add aborted job status
- disable d3 hot delay
- mmu fixes
nouveau:
- fix gsp rpc size request
- fix dma buffer leaks
- use common code for gsp mem ctor
xe:
- Fix a loop in an error path
- Fix a missing dma-fence reference
- Fix a retry path on userptr REMAP
- Workaround for a false gcc warning
- Fix missing map of the usm batch buffer in the migrate vm.
- Fix a memory leak.
- Fix a bad assumption of used page size
- Fix hitting a BUG() due to zero pages to map.
- Remove some leftover async bind queue relics
amdgpu:
- Misc NULL/bounds check fixes
- ODM pipe policy fix
- Aborted suspend fixes
- JPEG 4.0.5 fix
- DCN 3.5 fixes
- PSP fix
- DP MST fix
- Phantom pipe fix
- VRAM vendor fix
- Clang fix
- SR-IOV fix
msm:
- DPU:
- fix for kernel doc warnings and smatch warnings in dpu_encoder
- fix for smatch warning in dpu_encoder
- fix the bus bandwidth value for SDM670
- DP:
- fixes to handle unknown bpc case correctly for DP
- fix for MISC0 programming
- GPU:
- dmabuf vmap fix
- a610 UBWC corruption fix (incorrect hbb)
- revert a commit that was making GPU recovery unreliable"
* tag 'drm-fixes-2024-02-09' of git://anongit.freedesktop.org/drm/drm: (43 commits)
drm/xe: Remove TEST_VM_ASYNC_OPS_ERROR
drm/xe/vm: don't ignore error when in_kthread
drm/xe: Assume large page size if VMA not yet bound
drm/xe/display: Fix memleak in display initialization
drm/xe: Map both mem.kernel_bb_pool and usm.bb_pool
drm/xe: circumvent bogus stringop-overflow warning
drm/xe: Pick correct userptr VMA to repin on REMAP op failure
drm/xe: Take a reference in xe_exec_queue_last_fence_get()
drm/xe: Fix loop in vm_bind_ioctl_ops_unwind
drm/amdgpu: Fix HDP flush for VFs on nbio v7.9
drm/amd/display: Implement bounds check for stream encoder creation in DCN301
drm/amd/display: Increase frame-larger-than for all display_mode_vba files
drm/amd/display: Clear phantom stream count and plane count
drm/amdgpu: Avoid fetching VRAM vendor info
drm/amd/display: Disable ODM by default for DCN35
drm/amd/display: Update phantom pipe enable / disable sequence
drm/amd/display: Fix MST Null Ptr for RV
drm/amdgpu: Fix shared buff copy to user
drm/amd/display: Increase eval/entry delay for DCN35
drm/amdgpu: remove asymmetrical irq disabling in jpeg 4.0.5 suspend
...
Pull networking fixes from Paolo Abeni:
"Including fixes from WiFi and netfilter.
Current release - regressions:
- nic: intel: fix old compiler regressions
- netfilter: ipset: missing gc cancellations fixed
Current release - new code bugs:
- netfilter: ctnetlink: fix filtering for zone 0
Previous releases - regressions:
- core: fix from address in memcpy_to_iter_csum()
- netfilter: nfnetlink_queue: un-break NF_REPEAT
- af_unix: fix memory leak for dead unix_(sk)->oob_skb in GC.
- devlink: avoid potential loop in devlink_rel_nested_in_notify_work()
- iwlwifi:
- mvm: fix a battery life regression
- fix double-free bug
- mac80211: fix waiting for beacons logic
- nic: nfp: flower: prevent re-adding mac index for bonded port
Previous releases - always broken:
- rxrpc: fix generation of serial numbers to skip zero
- tipc: check the bearer type before calling tipc_udp_nl_bearer_add()
- tunnels: fix out of bounds access when building IPv6 PMTU error
- nic: hv_netvsc: register VF in netvsc_probe if NET_DEVICE_REGISTER
missed
- nic: atlantic: fix DMA mapping for PTP hwts ring
Misc:
- selftests: more fixes to deal with very slow hosts"
* tag 'net-6.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (80 commits)
netfilter: nft_set_pipapo: remove scratch_aligned pointer
netfilter: nft_set_pipapo: add helper to release pcpu scratch area
netfilter: nft_set_pipapo: store index in scratch maps
netfilter: nft_set_rbtree: skip end interval element from gc
netfilter: nfnetlink_queue: un-break NF_REPEAT
netfilter: nf_tables: use timestamp to check for set element timeout
netfilter: nft_ct: reject direction for ct id
netfilter: ctnetlink: fix filtering for zone 0
s390/qeth: Fix potential loss of L3-IP@ in case of network issues
netfilter: ipset: Missing gc cancellations fixed
octeontx2-af: Initialize maps.
net: ethernet: ti: cpsw: enable mac_managed_pm to fix mdio
net: ethernet: ti: cpsw_new: enable mac_managed_pm to fix mdio
netfilter: nft_set_pipapo: remove static in nft_pipapo_get()
netfilter: nft_compat: restrict match/target protocol to u16
netfilter: nft_compat: reject unused compat flag
netfilter: nft_compat: narrow down revision to unsigned 8-bits
net: intel: fix old compiler regressions
MAINTAINERS: Maintainer change for rds
selftests: cmsg_ipv6: repeat the exact packet
...
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Narrow down target/match revision to u8 in nft_compat.
2) Bail out with unused flags in nft_compat.
3) Restrict layer 4 protocol to u16 in nft_compat.
4) Remove static in pipapo get command that slipped through when
reducing set memory footprint.
5) Follow up incremental fix for the ipset performance regression,
this includes the missing gc cancellation, from Jozsef Kadlecsik.
6) Allow to filter by zone 0 in ctnetlink, do not interpret zone 0
as no filtering, from Felix Huettner.
7) Reject direction for NFT_CT_ID.
8) Use timestamp to check for set element expiration while transaction
is handled to prevent garbage collection from removing set elements
that were just added by this transaction. Packet path and netlink
dump/get path still use current time to check for expiration.
9) Restore NF_REPEAT in nfnetlink_queue, from Florian Westphal.
10) map_index needs to be percpu and per-set, not just percpu.
At this time its possible for a pipapo set to fill the all-zero part
with ones and take the 'might have bits set' as 'start-from-zero' area.
From Florian Westphal. This includes three patches:
- Change scratchpad area to a structure that provides space for a
per-set-and-cpu toggle and uses it of the percpu one.
- Add a new free helper to prepare for the next patch.
- Remove the scratch_aligned pointer and makes AVX2 implementation
use the exact same memory addresses for read/store of the matching
state.
netfilter pull request 24-02-08
* tag 'nf-24-02-08' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nft_set_pipapo: remove scratch_aligned pointer
netfilter: nft_set_pipapo: add helper to release pcpu scratch area
netfilter: nft_set_pipapo: store index in scratch maps
netfilter: nft_set_rbtree: skip end interval element from gc
netfilter: nfnetlink_queue: un-break NF_REPEAT
netfilter: nf_tables: use timestamp to check for set element timeout
netfilter: nft_ct: reject direction for ct id
netfilter: ctnetlink: fix filtering for zone 0
netfilter: ipset: Missing gc cancellations fixed
netfilter: nft_set_pipapo: remove static in nft_pipapo_get()
netfilter: nft_compat: restrict match/target protocol to u16
netfilter: nft_compat: reject unused compat flag
netfilter: nft_compat: narrow down revision to unsigned 8-bits
====================
Link: https://lore.kernel.org/r/20240208112834.1433-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add a timestamp field at the beginning of the transaction, store it
in the nftables per-netns area.
Update set backend .insert, .deactivate and sync gc path to use the
timestamp, this avoids that an element expires while control plane
transaction is still unfinished.
.lookup and .update, which are used from packet path, still use the
current time to check if the element has expired. And .get path and dump
also since this runs lockless under rcu read size lock. Then, there is
async gc which also needs to check the current time since it runs
asynchronously from a workqueue.
Fixes: c3e1b005ed ("netfilter: nf_tables: add set element timeout support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Flag (1 << 0) is ignored is set, never used, reject it it with EINVAL
instead.
Fixes: 0ca743a559 ("netfilter: nf_tables: add compatibility layer for x_tables")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Kalle Valo says:
====================
wireless fixes for v6.8-rc4
This time we have unusually large wireless pull request. Several
functionality fixes to both stack and iwlwifi. Lots of fixes to
warnings, especially to MODULE_DESCRIPTION().
* tag 'wireless-2024-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: (31 commits)
wifi: mt76: mt7996: fix fortify warning
wifi: brcmfmac: Adjust n_channels usage for __counted_by
wifi: iwlwifi: do not announce EPCS support
wifi: iwlwifi: exit eSR only after the FW does
wifi: iwlwifi: mvm: fix a battery life regression
wifi: mac80211: accept broadcast probe responses on 6 GHz
wifi: mac80211: adding missing drv_mgd_complete_tx() call
wifi: mac80211: fix waiting for beacons logic
wifi: mac80211: fix unsolicited broadcast probe config
wifi: mac80211: initialize SMPS mode correctly
wifi: mac80211: fix driver debugfs for vif type change
wifi: mac80211: set station RX-NSS on reconfig
wifi: mac80211: fix RCU use in TDLS fast-xmit
wifi: mac80211: improve CSA/ECSA connection refusal
wifi: cfg80211: detect stuck ECSA element in probe resp
wifi: iwlwifi: remove extra kernel-doc
wifi: fill in MODULE_DESCRIPTION()s for mt76 drivers
wifi: fill in MODULE_DESCRIPTION()s for wilc1000
wifi: fill in MODULE_DESCRIPTION()s for wl18xx
wifi: fill in MODULE_DESCRIPTION()s for p54spi
...
====================
Link: https://lore.kernel.org/r/20240206095722.CD9D2C433F1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A short read may occur while reading the message footer from the
socket. Later, when the socket is ready for another read, the
messenger invokes all read_partial_*() handlers, including
read_partial_sparse_msg_data(). The expectation is that
read_partial_sparse_msg_data() would bail, allowing the messenger to
invoke read_partial() for the footer and pick up where it left off.
However read_partial_sparse_msg_data() violates that and ends up
calling into the state machine in the OSD client. The sparse-read
state machine assumes that it's a new op and interprets some piece of
the footer as the sparse-read header and returns bogus extents/data
length, etc.
To determine whether read_partial_sparse_msg_data() should bail, let's
reuse cursor->total_resid. Because once it reaches to zero that means
all the extents and data have been successfully received in last read,
else it could break out when partially reading any of the extents and
data. And then osd_sparse_read() could continue where it left off.
[ idryomov: changelog ]
Link: https://tracker.ceph.com/issues/63586
Fixes: d396f89db3 ("libceph: add sparse read support to msgr1")
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The detection of dirty-throttled tasks in blk-wbt has been subtly broken
since its beginning in 2016. Namely if we are doing cgroup writeback and
the throttled task is not in the root cgroup, balance_dirty_pages() will
set dirty_sleep for the non-root bdi_writeback structure. However
blk-wbt checks dirty_sleep only in the root cgroup bdi_writeback
structure. Thus detection of recently throttled tasks is not working in
this case (we noticed this when we switched to cgroup v2 and suddently
writeback was slow).
Since blk-wbt has no easy way to get to proper bdi_writeback and
furthermore its intention has always been to work on the whole device
rather than on individual cgroups, just move the dirty_sleep timestamp
from bdi_writeback to backing_dev_info. That fixes the checking for
recently throttled task and saves memory for everybody as a bonus.
CC: stable@vger.kernel.org
Fixes: b57d74aff9 ("writeback: track if we're sleeping on progress in balance_dirty_pages()")
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20240123175826.21452-1-jack@suse.cz
[axboe: fixup indentation errors]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
commit dfad37051a ("remap_range: move permission hooks out of
do_clone_file_range()") moved the permission hooks from
do_clone_file_range() out to its caller vfs_clone_file_range(),
but left all the fast sanity checks in do_clone_file_range().
This makes the expensive security hooks be called in situations
that they would not have been called before (e.g. fs does not support
clone).
The only reason for the do_clone_file_range() helper was that overlayfs
did not use to be able to call vfs_clone_file_range() from copy up
context with sb_writers lock held. However, since commit c63e56a4a6
("ovl: do not open/llseek lower file with upper sb_writers held"),
overlayfs just uses an open coded version of vfs_clone_file_range().
Merge_clone_file_range() into vfs_clone_file_range(), restoring the
original order of checks as it was before the regressing commit and adapt
the overlayfs code to call vfs_clone_file_range() before the permission
hooks that were added by commit ca7ab48240 ("ovl: add permission hooks
outside of do_splice_direct()").
Note that in the merge of do_clone_file_range(), the file_start_write()
context was reduced to cover ->remap_file_range() without holding it
over the permission hooks, which was the reason for doing the regressing
commit in the first place.
Reported-and-tested-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202401312229.eddeb9a6-oliver.sang@intel.com
Fixes: dfad37051a ("remap_range: move permission hooks out of do_clone_file_range()")
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Link: https://lore.kernel.org/r/20240202102258.1582671-1-amir73il@gmail.com
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
The hrtimers migration on CPU-down hotplug process has been moved
earlier, before the CPU actually goes to die. This leaves a small window
of opportunity to queue an hrtimer in a blind spot, leaving it ignored.
For example a practical case has been reported with RCU waking up a
SCHED_FIFO task right before the CPUHP_AP_IDLE_DEAD stage, queuing that
way a sched/rt timer to the local offline CPU.
Make sure such situations never go unnoticed and warn when that happens.
Fixes: 5c0930ccaa ("hrtimers: Push pending hrtimers away from outgoing CPU earlier")
Reported-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240129235646.3171983-4-boqun.feng@gmail.com
Fix the counting of new acks and nacks when parsing a packet - something
that is used in congestion control.
As the code stands, it merely notes if there are any nacks whereas what we
really should do is compare the previous SACK table to the new one,
assuming we get two successive ACK packets with nacks in them. However, we
really don't want to do that if we can avoid it as the tables might not
correspond directly as one may be shifted from the other - something that
will only get harder to deal with once extended ACK tables come into full
use (with a capacity of up to 8192).
Instead, count the number of nacks shifted out of the old SACK, the number
of nacks retained in the portion still active and the number of new acks
and nacks in the new table then calculate what we need.
Note this ends up a bit of an estimate as the Rx protocol allows acks to be
withdrawn by the receiver and packets requested to be retransmitted.
Fixes: d57a3a1516 ("rxrpc: Save last ACK's SACK table rather than marking txbufs")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ext4 fixes from Ted Ts'o:
"Miscellaneous bug fixes and cleanups in ext4's multi-block allocator
and extent handling code"
* tag 'for-linus-6.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (23 commits)
ext4: make ext4_set_iomap() recognize IOMAP_DELALLOC map type
ext4: make ext4_map_blocks() distinguish delalloc only extent
ext4: add a hole extent entry in cache after punch
ext4: correct the hole length returned by ext4_map_blocks()
ext4: convert to exclusive lock while inserting delalloc extents
ext4: refactor ext4_da_map_blocks()
ext4: remove 'needed' in trace_ext4_discard_preallocations
ext4: remove unnecessary parameter "needed" in ext4_discard_preallocations
ext4: remove unused return value of ext4_mb_release_group_pa
ext4: remove unused return value of ext4_mb_release_inode_pa
ext4: remove unused return value of ext4_mb_release
ext4: remove unused ext4_allocation_context::ac_groups_considered
ext4: remove unneeded return value of ext4_mb_release_context
ext4: remove unused parameter ngroup in ext4_mb_choose_next_group_*()
ext4: remove unused return value of __mb_check_buddy
ext4: mark the group block bitmap as corrupted before reporting an error
ext4: avoid allocating blocks from corrupted group in ext4_mb_find_by_goal()
ext4: avoid allocating blocks from corrupted group in ext4_mb_try_best_found()
ext4: avoid dividing by 0 in mb_update_avg_fragment_size() when block bitmap corrupt
ext4: avoid bb_free and bb_fragments inconsistency in mb_free_blocks()
...
Pull tty and serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.8-rc3 that
resolve a number of reported issues. Included in here are:
- rs485 flag definition fix that affected the user/kernel abi in -rc1
- max310x driver fixes
- 8250_pci1xxxx driver off-by-one fix
- uart_tiocmget locking race fix
All of these have been in linux-next for over a week with no reported
issues"
* tag 'tty-6.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: max310x: prevent infinite while() loop in port startup
serial: max310x: fail probe if clock crystal is unstable
serial: max310x: improve crystal stable clock detection
serial: max310x: set default value when reading clock ready bit
serial: core: Fix atomicity violation in uart_tiocmget
serial: 8250_pci1xxxx: fix off by one in pci1xxxx_process_read_data()
tty: serial: Fix bit order in RS485 flag definitions
Pull dmaengine fixes from Vinod Koul:
"Core:
- fix return value of is_slave_direction() for D2D dma
Driver fixes for:
- Documentaion fixes to resolve warnings for at_hdmac driver
- bunch of fsl driver fixes for memory leaks, and useless kfree
- TI edma and k3 fixes for packet error and null pointer checks"
* tag 'dmaengine-fix-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: at_hdmac: add missing kernel-doc style description
dmaengine: fix is_slave_direction() return false when DMA_DEV_TO_DEV
dmaengine: fsl-qdma: Remove a useless devm_kfree()
dmaengine: fsl-qdma: Fix a memory leak related to the queue command DMA
dmaengine: fsl-qdma: Fix a memory leak related to the status queue DMA
dmaengine: ti: k3-udma: Report short packet errors
dmaengine: ti: edma: Add some null pointer checks to the edma_probe
dmaengine: fsl-dpaa2-qdma: Fix the size of dma pools
dmaengine: at_hdmac: fix some kernel-doc warnings
Jonathan reports that CXL CPER events dump an extra generic error
message.
{1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 1
{1}[Hardware Error]: event severity: recoverable
{1}[Hardware Error]: Error 0, type: recoverable
{1}[Hardware Error]: section type: unknown, fbcd0a77-c260-417f-85a9-088b1621eba6
{1}[Hardware Error]: section length: 0x90
{1}[Hardware Error]: 00000000: 00000090 00000007 00000000 0d938086 ................
{1}[Hardware Error]: 00000010: 00100000 00000000 00040000 00000000 ................
...
CXL events were rerouted though the CXL subsystem for additional
processing. However, when that work was done it was missed that
cper_estatus_print_section() continued with a generic error message
which is confusing.
Teach CPER print code to ignore printing details of some section types.
Assign the CXL event GUIDs to this set to prevent confusing unknown
prints.
Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Pull pci fixes from Bjorn Helgaas:
- Fix a potential deadlock that was reintroduced by an ASPM revert
merged for v6.8 (Johan Hovold)
- Add Manivannan Sadhasivam as PCI Endpoint maintainer (Lorenzo
Pieralisi)
* tag 'pci-v6.8-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
MAINTAINERS: Add Manivannan Sadhasivam as PCI Endpoint maintainer
PCI/ASPM: Fix deadlock when enabling ASPM
Pull sound fixes from Takashi Iwai:
"A collection of fixes, mostly device-specific ones:
- Minor PCM core fix for name strings
- ASoC Qualcomm fixes, including DAI support extensions
- ASoC AMD platform updates
- ASoC Allwinner platform updates
- Various ASoC codec fixes for WSA, WCD, ES8326 drivers
- Various HD-audio and USB-audio fixes and quirks
- A series of fixes for Cirrus CS35L56 codecs"
* tag 'sound-6.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (63 commits)
ALSA: usb-audio: Ignore clock selector errors for single connection
ALSA: hda/realtek: Enable headset mic on Vaio VJFE-ADL
ALSA: hda: cs35l56: Remove unused test stub function
ALSA: hda: cs35l56: Firmware file must match the version of preloaded firmware
ALSA: hda: cs35l56: Fix filename string field layout
ALSA: hda: cs35l56: Fix order of searching for firmware files
ASoC: cs35l56: Allow more time for firmware to boot
ASoC: cs35l56: Load tunings for the correct speaker models
ASoC: cs35l56: Firmware file must match the version of preloaded firmware
ASoC: cs35l56: Fix misuse of wm_adsp 'part' string for silicon revision
ASoC: cs35l56: Fix for initializing ASP1 mixer registers
ALSA: hda: cs35l56: Initialize all ASP1 registers
ASoC: cs35l56: Fix default SDW TX mixer registers
ASoC: cs35l56: Fix to ensure ASP1 registers match cache
ASoC: cs35l56: Remove buggy checks from cs35l56_is_fw_reload_needed()
ASoC: cs35l56: Don't add the same register patch multiple times
ASoC: cs35l56: cs35l56_component_remove() must clean up wm_adsp
ASoC: cs35l56: cs35l56_component_remove() must clear cs35l56->component
ASoC: wm_adsp: Don't overwrite fwf_name with the default
ASoC: wm_adsp: Fix firmware file search order
...
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- Remove duplicated enums (Guixen)
- Use appropriate controller state accessors (Keith)
- Retryable authentication (Hannes)
- Add missing module descriptions (Chaitanya)
- Fibre-channel fixes for blktests (Daniel)
- Various type correctness updates (Caleb)
- Improve fabrics connection debugging prints (Nitin)
- Passthrough command verbose error logging (Adam)
- Fix for where we set IO priority in the bio for drivers that use
fops->submit_bio() to queue IO, like md/dm etc.
* tag 'block-6.8-2024-02-01' of git://git.kernel.dk/linux: (32 commits)
block: Fix where bio IO priority gets set
nvme: allow passthru cmd error logging
nvme-fc: show hostnqn when connecting to fc target
nvme-rdma: show hostnqn when connecting to rdma target
nvme-tcp: show hostnqn when connecting to tcp target
nvmet-fc: use RCU list iterator for assoc_list
nvmet-fc: take ref count on tgtport before delete assoc
nvmet-fc: avoid deadlock on delete association path
nvmet-fc: abort command when there is no binding
nvmet-fc: do not tack refs on tgtports from assoc
nvmet-fc: remove null hostport pointer check
nvmet-fc: hold reference on hostport match
nvmet-fc: free queue and assoc directly
nvmet-fc: defer cleanup using RCU properly
nvmet-fc: release reference on target port
nvmet-fcloop: swap the list_add_tail arguments
nvme-fc: do not wait in vain when unloading module
nvme-fc: log human-readable opcode on timeout
nvme: split out fabrics version of nvme_opcode_str()
nvme: take const cmd pointer in read-only helpers
...
We recently added some validation that we don't try to
connect to an AP that is currently in a channel switch
process, since that might want the channel to be quiet
or we might not be able to connect in time to hear the
switching in a beacon. This was in commit c09c4f3199
("wifi: mac80211: don't connect to an AP while it's in
a CSA process").
However, we promptly got a report that this caused new
connection failures, and it turns out that the AP that
we now cannot connect to is permanently advertising an
extended channel switch announcement, even with quiet.
The AP in question was an Asus RT-AC53, with firmware
3.0.0.4.380_10760-g21a5898.
As a first step, attempt to detect that we're dealing
with such a situation, so mac80211 can use this later.
Reported-by: coldolt <andypalmadi@gmail.com>
Closes: https://lore.kernel.org/linux-wireless/CAJvGw+DQhBk_mHXeu6RTOds5iramMW2FbMB01VbKRA4YbHHDTA@mail.gmail.com/
Fixes: c09c4f3199 ("wifi: mac80211: don't connect to an AP while it's in a CSA process")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129131413.246972c8775e.Ibf834d7f52f9951a353b6872383da710a7358338@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter.
As Paolo promised we continue to hammer out issues in our selftests.
This is not the end but probably the peak.
Current release - regressions:
- smc: fix incorrect SMC-D link group matching logic
Current release - new code bugs:
- eth: bnxt: silence WARN() when device skips a timestamp, it happens
Previous releases - regressions:
- ipmr: fix null-deref when forwarding mcast packets
- conntrack: evaluate window negotiation only for packets in the
REPLY direction, otherwise SYN retransmissions trigger incorrect
window scale negotiation
- ipset: fix performance regression in swap operation
Previous releases - always broken:
- tcp: add sanity checks to types of pages getting into the rx
zerocopy path, we only support basic NIC -> user, no page cache
pages etc.
- ip6_tunnel: make sure to pull inner header in __ip6_tnl_rcv()
- nt_tables: more input sanitization changes
- dsa: mt7530: fix 10M/100M speed on MediaTek MT7988 switch
- bridge: mcast: fix loss of snooping after long uptime, jiffies do
wrap on 32bit
- xen-netback: properly sync TX responses, protect with locking
- phy: mediatek-ge-soc: sync calibration values with MediaTek SDK,
increase connection stability
- eth: pds: fixes for various teardown, and reset races
Misc:
- hsr: silence WARN() if we can't alloc supervision frame, it
happens"
* tag 'net-6.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (82 commits)
doc/netlink/specs: Add missing attr in rt_link spec
idpf: avoid compiler padding in virtchnl2_ptype struct
selftests: mptcp: join: stop transfer when check is done (part 2)
selftests: mptcp: join: stop transfer when check is done (part 1)
selftests: mptcp: allow changing subtests prefix
selftests: mptcp: decrease BW in simult flows
selftests: mptcp: increase timeout to 30 min
selftests: mptcp: add missing kconfig for NF Mangle
selftests: mptcp: add missing kconfig for NF Filter in v6
selftests: mptcp: add missing kconfig for NF Filter
mptcp: fix data re-injection from stale subflow
selftests: net: enable some more knobs
selftests: net: add missing config for NF_TARGET_TTL
selftests: forwarding: List helper scripts in TEST_FILES Makefile variable
selftests: net: List helper scripts in TEST_FILES Makefile variable
selftests: net: Remove executable bits from library scripts
selftests: bonding: Check initial state
selftests: team: Add missing config options
hv_netvsc: Fix race condition between netvsc_probe and netvsc_remove
xen-netback: properly sync TX responses
...
Pull HID fixes from Benjamin Tissoires:
- cleanups in the error path in hid-steam (Dan Carpenter)
- fixes for Wacom tablets selftests that sneaked in while the CI was
taking a break during the year end holidays (Benjamin Tissoires)
- null pointer check in nvidia-shield (Kunwu Chan)
- memory leak fix in hidraw (Su Hui)
- another null pointer fix in i2c-hid-of (Johan Hovold)
- another memory leak fix in HID-BPF this time, as well as a double
fdget() fix reported by Dan Carpenter (Benjamin Tissoires)
- fix for Cirque touchpad when they go on suspend (Kai-Heng Feng)
- new device ID in hid-logitech-hidpp: "Logitech G Pro X SuperLight 2"
(Jiri Kosina)
* tag 'hid-for-linus-2024020101' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: bpf: use __bpf_kfunc instead of noinline
HID: bpf: actually free hdev memory after attaching a HID-BPF program
HID: bpf: remove double fdget()
HID: i2c-hid-of: fix NULL-deref on failed power up
HID: hidraw: fix a problem of memory leak in hidraw_release()
HID: i2c-hid: Skip SET_POWER SLEEP for Cirque touchpad on system suspend
HID: nvidia-shield: Add missing null pointer checks to LED initialization
HID: logitech-hidpp: add support for Logitech G Pro X Superlight 2
selftests/hid: wacom: fix confidence tests
HID: hid-steam: Fix cleanup in probe()
HID: hid-steam: remove pointless error message
Pull lsm fixes from Paul Moore:
"Two small patches to fix some problems relating to LSM hook return
values and how the individual LSMs interact"
* tag 'lsm-pr-20240131' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm:
lsm: fix default return value of the socket_getpeersec_*() hooks
lsm: fix the logic in security_inode_getsecctx()
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) TCP conntrack now only evaluates window negotiation for packets in
the REPLY direction, from Ryan Schaefer. Otherwise SYN retransmissions
trigger incorrect window scale negotiation. From Ryan Schaefer.
2) Restrict tunnel objects to NFPROTO_NETDEV which is where it makes sense
to use this object type.
3) Fix conntrack pick up from the middle of SCTP_CID_SHUTDOWN_ACK packets.
From Xin Long.
4) Another attempt from Jozsef Kadlecsik to address the slow down of the
swap command in ipset.
5) Replace a BUG_ON by WARN_ON_ONCE in nf_log, and consolidate check for
the case that the logger is NULL from the read side lock section.
6) Address lack of sanitization for custom expectations. Restrict layer 3
and 4 families to what it is supported by userspace.
* tag 'nf-24-01-31' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nft_ct: sanitize layer 3 and 4 protocol number in custom expectations
netfilter: nf_log: replace BUG_ON by WARN_ON_ONCE when putting logger
netfilter: ipset: fix performance regression in swap operation
netfilter: conntrack: check SCTP_CID_SHUTDOWN_ACK for vtag setting in sctp_new
netfilter: nf_tables: restrict tunnel object to NFPROTO_NETDEV
netfilter: conntrack: correct window scaling with retransmitted SYN
====================
Link: https://lore.kernel.org/r/20240131225943.7536-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the "spk-id-gpios" property is present it points to GPIOs whose
value must be used to select the correct bin file to match the
speakers.
Some manufacturers use multiple sources of speakers, which need
different tunings for best performance. On these models the type of
speaker fitted is indicated by the values of one or more GPIOs. The
number formed by the GPIOs identifies the tuning required.
The speaker ID must be used in combination with the subsystem ID
(either from PCI SSID or cirrus,firmware-uid property), because the
GPIOs can only indicate variants of a specific model.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 1a1c3d794e ("ASoC: cs35l56: Use PCI SSID as the firmware UID")
Link: https://msgid.link/r/20240129162737.497-14-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Check during initialization whether the firmware is already patched.
If so, include the firmware version in the wm_adsp fwf_name string.
If the firmware has already been patched by the BIOS the driver
can only replace it if it has control of hard RESET.
If the driver cannot replace the firmware, it can still load a wmfw
(for ALSA control definitions) and/or a bin (for additional tunings).
But these must match the version of firmware that is running on the
CS35L56.
The firmware is pre-patched if FIRMWARE_MISSING == 0.
Including the firmware version in the fwf_name string will
qualify the firmware file name:
Normal (unpatched or replaceable firmware):
cs35l56-rev-dsp1-misc[-system_name].[wmfw|bin]
Preloaded firmware:
cs35l56-rev[-s]-VVVVVV-dsp1-misc[-system_name].[wmfw|bin]
Where:
[-s] is an optional -s added into the name for a secured CS35L56
VVVVVV is the 24-bit firmware version in hexadecimal.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 608f1b0dbd ("ASoC: cs35l56: Move DSP part string generation so that it is done only once")
Link: https://msgid.link/r/20240129162737.497-13-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a dummy SUPPLY widget connected to the ASP that forces the
chip registers to match the regmap cache when the ASP is
powered-up.
On a SoundWire system the ASP is free for use as a chip-to-chip
interconnect. This can be either for the firmware on multiple
CS35L56 to share reference audio; or as a bridge to another
device. If it is a firmware interconnect it is owned by the
firmware and the Linux driver should avoid writing the registers.
However. If it is a bridge then Linux may take over and handle
it as a normal codec-to-codec link.
CS35L56 is designed for SDCA and a generic SDCA driver would
know nothing about these chip-specific registers. So if the
ASP is being used on a SoundWire system the firmware sets up the
ASP registers. This means that we can't assume the default
state of the ASP registers. But we don't know the initial state
that the firmware set them to until after the firmware has been
downloaded and booted, which can take several seconds when
downloading multiple amps.
To avoid blocking probe() for several seconds waiting for the
firmware, the silicon defaults are assumed. This allows the machine
driver to setup the ASP configuration during probe() without being
blocked. If the ASP is hooked up and used, the SUPPLY widget
ensures that the chip registers match what was configured in the
regmap cache.
If the machine driver does not hook up the ASP, it is assumed that
it won't call any functions to configure the ASP DAI. Therefore
the regmap cache will be clean for these registers so a
regcache_sync() will not overwrite the chip registers. If the
DAI is not hooked up, the dummy SUPPLY widget will not be
invoked so it will never force-overwrite the chip registers.
Backport note:
This won't apply cleanly to kernels older than v6.6.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e496112529 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Link: https://msgid.link/r/20240129162737.497-8-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
nvme_is_fabrics() and nvme_is_write() only read struct nvme_command,
so take it by const pointer. This allows callers to pass a const pointer
and communicates that these functions don't modify the command.
Signed-off-by: Caleb Sander <csander@purestorage.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
