Add selftest case to check the send and receive throughput.
Supported link modes between local NIC driver and partner
are varied. Then send and receive throughput is captured
and verified. Test uses iperf3 tool.
Add iperf3 server/client function in GenerateTraffic class.
Signed-off-by: Mohan Prasad J <mohan.prasad@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add selftest case for testing the speed and duplex state of
local NIC driver and the partner based on the supported
link modes obtained from the ethtool. Speed and duplex states
are varied and verified using ethtool.
Signed-off-by: Mohan Prasad J <mohan.prasad@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add selftest file for the link layer tests of a NIC driver.
Test for auto-negotiation is added.
Add LinkConfig class for changing link layer configs.
Selftest makes use of ksft modules and ethtool.
Include selftest file in the Makefile.
Signed-off-by: Mohan Prasad J <mohan.prasad@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The netconsole selftest relies on the availability of the netdevsim module.
To ensure the test can run correctly, we need to check if the netdevsim
module is either loaded or built-in before proceeding.
Update the netconsole selftest to check for the existence of
the /sys/bus/netdevsim/new_device file before running the test. If the
file is not found, the test is skipped with an explanation that the
CONFIG_NETDEVSIM kernel config option may not be enabled.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241108-netcon_selftest_deps-v1-1-1789cbf3adcd@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Only RX side for now and small message to test the setup.
In the future, we can extend it to TX side and to testing
both sides with a couple of megs of data.
make \
-C tools/testing/selftests \
TARGETS="drivers/hw/net" \
install INSTALL_PATH=~/tmp/ksft
scp ~/tmp/ksft ${HOST}:
scp ~/tmp/ksft ${PEER}:
cfg+="NETIF=${DEV}\n"
cfg+="LOCAL_V6=${HOST_IP}\n"
cfg+="REMOTE_V6=${PEER_IP}\n"
cfg+="REMOTE_TYPE=ssh\n"
cfg+="REMOTE_ARGS=root@${PEER}\n"
echo -e "$cfg" | ssh root@${HOST} "cat > ksft/drivers/net/net.config"
ssh root@${HOST} "cd ksft && ./run_kselftest.sh -t drivers/net:devmem.py"
Reviewed-by: Mina Almasry <almasrymina@google.com>
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/20241107181211.3934153-13-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend netcons_basic selftest to verify the userdata functionality by:
1. Creating a test key in the userdata configfs directory
2. Writing a known value to the key
3. Validating the key-value pair appears in the captured network output
This ensures the userdata feature is properly tested during selftests.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20241029090030.1793551-3-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the defer framework to schedule cleanups as soon as the command is
executed.
Note that the start_traffic commands in __burst_test() are each sending a
fixed number of packets (note the -c flag) and then ending. They therefore
do not need a matching stop_traffic.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use the defer framework to schedule cleanups as soon as the command is
executed.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use the defer framework to schedule cleanups as soon as the command is
executed.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use the defer framework to schedule cleanups as soon as the command is
executed.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use the defer framework to schedule cleanups as soon as the command is
executed.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of having a suite of dedicated cleanup functions, use the defer
framework to schedule cleanups right as their setup functions are run.
The sleep after stop_traffic() in mlxsw selftests is necessary, but
scheduling it as "defer sleep; defer stop_traffic" is silly. Instead, add a
local helper to stop traffic and sleep afterwards.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It should be invalid to delete an rss context while it is being
referenced from an ntuple filter. ethtool core should prevent this
from happening. This patch adds a testcase to verify this behavior.
Signed-off-by: Daniel Zahka <daniel.zahka@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The RED test uses a pair of TBF shapers. The first to get predictably-sized
stream of traffic, and second to get a 100% saturated chokepoint. To this
chokepoint it injects individual packets. Because the chokepoint is
saturated, these additional packets go straight to the backlog. This allows
the test to check RED behavior across various queue sizes.
The shapers are rated at 1Gbps, for historical reasons (before mlxsw
supported TBF offload, the test used port speed to create the chokepoints).
Machines with a low-power CPU may have trouble consistently generating
1Gbps of traffic, and the test then spuriously fails.
Instead, drop the rate to 200Mbps (Spectrum has a guaranteed shaper rate
granularity of 200Mbps, so anything lower is not guaranteed to work well).
Because that means fewer packets will be mirrored in the ECN-mark test,
adjust the passing condition accordingly.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/c6712f9c5de75ae0bc2ab3d8ea7d92aaaf93af95.1728316370.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This test works by injecting into a port with a maxed-out queue a couple
packets and checks if a corresponding number of packets were dropped. This
has worked well on Spectrum<4, but on Spectrum-4 it has been noisy. This
is in line with the observation that on Spectrum-4, queue size tends to
fluctuate more. A handful of packets could then still be accepted to the
queue even though it was nominally full just recently.
In order to accommodate this behavior, send many more packets. The buffer
can fit N extra packets, but not N% packets. This therefore allows us to
set wider absolute margins, while actually narrowing them relatively.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/abc869b9f6003d400d6293ddd5edb2f4517f44d5.1728316370.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The qdisc stats are taken from the port's periodic HW stats, which are
updated once a second. We try to accommodate the latency by using busywait
in build_backlog().
The issue in that seems to be that when do_mark_test() builds the backlog,
it makes the decision whether to send more packets based on the first
instance of the queue depth stat exceeding the current value, when in fact
more traffic is on the way and the queue depth would increase further. This
leads to failures in TC 1 of mark-mirror test, where we see the following
failure:
TEST: TC 0: marked packets mirror'd [ OK ]
TEST: TC 1: marked packets mirror'd [FAIL]
Spurious packets (1680 -> 2290) observed without buffer pressure
Fix by waiting for the full second before reading the queue depth for the
first time, to make sure it reflects all in-flight traffic.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Link: https://patch.msgid.link/321dcf8b3e9a1f0766429c8cf3e3f1746f1bc375.1728316370.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Backlog fluctuates on Spectrum-4 much more than on <4. In practice we can
sample queue depth values going from about -12% to about +7% of the
configured RED limit. The test which checks the queue size has a limit of
+-10%, and as a result often fails. We attempted to fix the issue by
busywaiting for several seconds hoping to get within the bounds, but that
still proved to be too noisy (or the wait time would be impractically
long). Unfortunately we have to bump the value tolerance from 10% to 15%,
which in this patch do.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Link: https://patch.msgid.link/f54950df2a8fcba46c3ddc1053376352fa2e592b.1728316370.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Adds a selftest that creates two virtual interfaces, assigns one to a
new namespace, and assigns IP addresses to both.
It listens on the destination interface using socat and configures a
dynamic target on netconsole, pointing to the destination IP address.
The test then checks if the message was received properly on the
destination interface.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240822095652.3806208-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a test for dumping RSS contexts. Make sure indir table
and key are sane when contexts are created with various
combination of inputs. Test the dump filtering by ifname
and start-context.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include the "name" of the context in the comment for traffic
checks. Makes it easier to reason about which context failed
when we loop over 32 contexts (it may matter if we failed in
first vs last, for example).
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new @ksft_disruptive decorator to mark the tests that might
be disruptive to the system. Depending on how well the previous
test works in the CI we might want to disable disruptive tests
by default and only let the developers run them manually.
KSFT framework runs disruptive tests by default. DISRUPTIVE=False
environment (or config file) can be used to disable these tests.
ksft_setup should be called by the test cases that want to use
new decorator (ksft_setup is only called via NetDrvEnv/NetDrvEpEnv for now).
In the future we can add similar decorators to, for example, avoid
running slow tests all the time. And/or have some option to run
only 'fast' tests for some sort of smoke test scenario.
$ DISRUPTIVE=False ./stats.py
KTAP version 1
1..5
ok 1 stats.check_pause
ok 2 stats.check_fec
ok 3 stats.pkt_byte_sum
ok 4 stats.qstat_by_ifindex
ok 5 stats.check_down # SKIP marked as disruptive
# Totals: pass:4 fail:0 xfail:0 xpass:0 skip:1 error:0
v3:
- parse yes and properly treat non-zero nums as true (Petr)
v2:
- convert from cli argument to env variable (Jakub)
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20240802000309.2368-2-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Verify that total device stats don't decrease after it has been turned down.
Also make sure the device doesn't crash when we access per-queue stats
when it's down (in case it tries to access some pointers that are NULL).
KTAP version 1
1..5
ok 1 stats.check_pause
ok 2 stats.check_fec
ok 3 stats.pkt_byte_sum
ok 4 stats.qstat_by_ifindex
ok 5 stats.check_down
# Totals: pass:5 fail:0 xfail:0 xpass:0 skip:0 error:0
v3:
- use errno.EOPNOTSUPP (Petr)
- move qstat[0] under try (Petr)
v2:
- KTAP output formatting (Jakub)
- defer instead of try/finally (Jakub)
- disappearing stats is an error (Jakub)
- ksft_ge instead of open coding (Jakub)
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20240802000309.2368-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We had a handful of bugs relating to key being either all 0
or just reported incorrectly as all 0. Check for this in
the tests.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some workloads may want to rehash the flows in response to an imbalance.
Most effective way to do that is changing the RSS key. Check that changing
the key does not cause link flaps or traffic disruption.
Disrupting traffic for key update is not incorrect, but makes the key
update unusable for rehashing under load.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20240708213627.226025-6-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some devices dynamically increase and decrease the size of the RSS
indirection table based on the number of enabled queues.
When that happens driver must maintain the balance of entries
(preferably duplicating the smaller table).
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20240708213627.226025-5-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
By default main RSS table should change to include all queues.
When user sets a specific RSS config the driver should preserve it,
even when queue count changes. Driver should refuse to deactivate
queues used in the user-set RSS config.
For additional contexts driver should still refuse to deactivate
queues in use. Whether the contexts should get resized like
context 0 when queue count increases is a bit unclear. I anticipate
most drivers today don't do that. Since main use case for additional
contexts is to set the indir table - it doesn't seem worthwhile to
care about behavior of the default table too much. Don't test that.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20240708213627.226025-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Wrap up sending traffic and checking in which queues it landed
in a helper.
The method used for testing is to send a lot of iperf traffic
and check which queues received the most packets. Those should
be the queues where we expect iperf to land - either because we
installed a filter for the port iperf uses, or we didn't and
expect it to use context 0.
Contexts get disjoint queue sets, but the main context (AKA context 0)
may receive some background traffic (noise).
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20240708213627.226025-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
