[Why]
Find out when we try to disable CRC calculation, crc generation is still
enabled. Main reason is that dc_stream_configure_crc() will never get
called when the source is AMDGPU_DM_PIPE_CRC_SOURCE_NONE.
[How]
Add checking condition that when source is
AMDGPU_DM_PIPE_CRC_SOURCE_NONE, we should also call
dc_stream_configure_crc() to disable crc calculation.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The address of the GOLDEN_TSC_COUNT_UPPER/GOLDEN_TSC_COUNT_LOWER for
Vnagogh are different from the others.
The offset of the GOLDEN_TSC_COUNT_UPPER for Vangogh is 0x0025 by
calculation.
The offset of the GOLDEN_TSC_COUNT_LOWER for Vangogh is 0x0026 by
calculation.
Signed-off-by: chen gong <curry.gong@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
KASAN reported a slab-out-of-bounds read of size 1 in
kdf_create_vcrat_image_cpu().
This occurs when, for example, when on an x86_64 with a single NUMA node
because kfd_fill_iolink_info_for_cpu() is a no-op, but afterwards the
sub_type_hdr->length, which is out-of-bounds, is read and multiplied by
entries. Fortunately, entries is 0 in this case so the overall
crat_table->length is still correct.
Check if there were any entries before de-referencing sub_type_hdr which
may be pointing to out-of-bounds memory.
Fixes: b7b6c38529 ("drm/amdkfd: Calculate CPU VCRAT size dynamically (v2)")
Suggested-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The initial purpose of dcn10 pipe split is to support some high
bandwidth mode which requires dispclk greater than max dispclk. By
initial bring up power measurement data, it showed power consumption is
less with pipe split for dcn block. This could be reason for enable pipe
split by default. By battery life measurement of some Chromebooks,
result shows battery life is longer with pipe split disabled.
[How]
Disable pipe split by default. Pipe split could be still enabled when
required dispclk is greater than max dispclk.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
psp GFX_CTRL_CMD_ID_CONSUME_CMD different for windows and linux,
according to psp, linux cmds are not correct.
v2: only correct GFX_CTRL_CMD_ID_CONSUME_CMD.
Signed-off-by: Victor Zhao <Victor.Zhao@amd.com>
Reviewed-by: Emily.Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
From Ard:
"Simply disabling -mgeneral-regs-only left and right is risky, given that
the standard AArch64 ABI permits the use of FP/SIMD registers anywhere,
and GCC is known to use SIMD registers for spilling, and may invent
other uses of the FP/SIMD register file that have nothing to do with the
floating point code in question. Note that putting kernel_neon_begin()
and kernel_neon_end() around the code that does use FP is not sufficient
here, the problem is in all the other code that may be emitted with
references to SIMD registers in it.
So the only way to do this properly is to put all floating point code in
a separate compilation unit, and only compile that unit with
-mgeneral-regs-only."
Disable support until the code can be properly refactored to support this
properly on aarch64.
Acked-by: Will Deacon <will@kernel.org>
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
old code wrongly used the bad page status as the function return value,
which cause amdgpu_ras_badpages_read always return failed.
Signed-off-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Navi12 HDCP & DTM deinitialization needs continue to free bo if already
created though initialized flag is not set.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jiawei Gu <Jiawei.Gu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some of the newly added code is hidden inside of #ifdef
blocks, but one variable is unused when debugfs is disabled:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:8370:8: error: unused variable 'configure_crc' [-Werror,-Wunused-variable]
Change the #ifdef to an if(IS_ENABLED()) check to fix the warning
and avoid adding more #ifdefs.
Fixes: c920888c60 ("drm/amd/display: Expose new CRC window property")
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to improve the fine grain tuning function for RV/RV2/PCO.
The fine grain tuning function uses the sysfs node -- pp_od_clk_voltage
to config gfxclk. Meanwhile, another sysfs
node -- power_dpm_force_perfomance_level also affects the gfx clk.
It will cause confusion when these two sysfs nodes works
together. So this patch adds one flag to avoid this confusion, the flag
will make these two sysfs nodes work separately.
The flag is set as "disabled" by default, so the fine grain tuning function
will be disabled by default.
Only when power_dpm_force_perfomance_level is changed to
"manual" mode, the flag will be set as "enabled",
and the fine grain tuning function will be enabled.
In other profile modes, including "auto", "high", "low",
"profile_peak", "profile_standard", "profile_min_sclk",
"profile_min_mclk", the flag will be set as "disabled",
and the od range of fine grain tuning function will
be restored default value.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When GFXOFF is enabled and GPU is idle, driver will fail to access some
registers. Therefore change to disable power gating before all access
registers with MMIO.
Dmesg log is as following:
amdgpu 0000:03:00.0: amdgpu: amdgpu: finishing device.
amdgpu: cp queue pipe 4 queue 0 preemption failed
amdgpu 0000:03:00.0: amdgpu: failed to write reg 2890 wait reg 28a2
amdgpu 0000:03:00.0: amdgpu: failed to write reg 1a6f4 wait reg 1a706
amdgpu 0000:03:00.0: amdgpu: failed to write reg 2890 wait reg 28a2
amdgpu 0000:03:00.0: amdgpu: failed to write reg 1a6f4 wait reg 1a706
Signed-off-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to improve the fine grain tuning function for RV/RV2/PCO.
This patch adds two new commands: "restore" and "commit".
This function uses the pp_od_clk_voltage sysfs file to configure the min
and max value of gfx clock frequency manually or restore the default value.
Command guide:
echo "s level value" > pp_od_clk_voltage
"s" - set the sclk frequency
"level" - 0 or 1, "0" represents the min value, "1" represents
the max value
"value" - the target value of sclk frequency, it should be limited in the
safe range
echo "r" > pp_od_clk_voltage
"r" - reset the sclk frequency, restore the default value instantly
echo "c" > pp_od_clk_voltage
"c" - commit the min and max value of sclk frequency to the system
only after the commit command, the target values set by "s" command
will take effect.
Example:
1)change power profile from "auto" to "manual"
$ cat power_dpm_force_performance_level
auto
$ echo "manual" > power_dpm_force_performance_level
$ cat power_dpm_force_performance_level
manual
2)check the default sclk frequency
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
3)use "s" -- set command to configure the min and max sclk frequency
$ echo "s 0 600" > pp_od_clk_voltage
$ echo "s 1 1000" > pp_od_clk_voltage
$ echo "c" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 600Mhz
1: 1000Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
4)use "r" -- reset command to restore the min or max sclk frequency
$ echo "r" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
clang (quite rightly) complains fairly loudly about the newly added
mpc1_get_mpc_out_mux() function returning an uninitialized value if the
'opp_id' checks don't pass.
This may not happen in practice, but the code really shouldn't return
garbage if the sanity checks don't pass.
So just initialize 'val' to zero to avoid the issue.
Fixes: 110b055b28 ("drm/amd/display: add getter routine to retrieve mpcc mux")
Cc: Josip Pavic <Josip.Pavic@amd.com>
Cc: Bindu Ramamurthy <bindu.r@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[Why]
We defer clock updates to after pipes have been programmed. In
some instances we use DPPCLK that have been previously set to be
"unused". This results in a brief window of time where underflow
could occur.
[How]
During prepare bandwidth allow rn_update_clocks_update_dpp_dto
to check each instance and compare previous clock to new clock.
If new clock is higher than previous clock, program DPPDTO.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- restore lvtma_pwrseq_delay2 from vbios integrated info table
- restore MVID/NVID after power up.
- Enable timer wake up mask when enable timer interrupt.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For certain timings, Renoir may underflow due to sr exit latency
being too slow.
[How]
Updated wm table for renoir.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DSC should only be acquired per OPP. Therefore, DSC should only
be acquired for the top_pipe when ODM is enabled.
Not doing this check may lead to acquiring more DSC's than needed
when doing MPO + ODM Combine.
[HOW]
Only acquire DSC if pipe is top_pipe.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
FP2 programming not happening when topology changes occur with multiple
displays.
[How]
Ensure FP2 is programmed whenever global sync changes occur but wait for
VACTIVE first to avoid underflow.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
new_crtc_state is already dereferenced earlier in the function
[How]
Remove the check
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Virtual signals were previously counted as a workaround to S0i2 hang
which is fixed on Renoir. This blocks S0i3 diags testing.
[HOW]
Stop counting virtual signals as S0i2 hang is fixed on Renoir.
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
there is some garbage showing up during reboot test.
Reason:
SMU might handle display driver msg defered and driver will send
next msg to SMU after 10ms timeout, once SMU FW handle previous msg,
parameters are changed to next one, which result in a wrong value be programmed.
[How]
Extend timeout to 2s so SMU will have enough time to handle driver msg.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need driver to pass values of backlight ramp start and ramp reduction so
that intensity can be ramped down appropriately.
[How]
Using abm_parameters structure to get these values from driver.
Signed-off-by: Rizvi <syerizvi@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The sink count change HPD_IRQ will be ignored if the branch device has only
DP DFP.
[how]
To remove the port type restriction.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
