Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter and IPsec.
Current release - regressions:
- do not acquire dev->tx_global_lock in netdev_watchdog_up()
- ethtool: keep rtnl_lock for ops using ethtool_op_get_link()
- fix deadlock in nested UP notifier events
Current release - new code bugs:
- eth:
- cn20k: fix subbank free list indexing for search order
- airoha: fix BQL underflow in shared QDMA TX ring
Previous releases - regressions:
- netfilter:
- flowtable: fix offloaded ct timeout never being extended
- nf_conncount: prevent connlimit drops for early confirmed ct
Previous releases - always broken:
- require CAP_NET_ADMIN in the originating netns when modifying
cross-netns devices
- report NAPI thread PID in the caller's pid namespace
- mac802154: fix dirty frag in in-place crypto for IOT radios
- sctp: hold socket lock when dumping endpoints in sctp_diag, avoid
an overflow
- eth: gve: fix header buffer corruption with header-split and HW-GRO
- af_key: initialize alg_key_len for IPComp states, prevent OOB read"
* tag 'net-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (213 commits)
selftests: bonding: add a test for VLAN propagation over a bonded real device
vlan: defer real device state propagation to netdev_work
net: add the driver-facing netdev_work scheduling API
net: turn the rx_mode work into a generic netdev_work facility
net: ethtool: keep rtnl_lock for ops using ethtool_op_get_link()
rxrpc: Fix rxrpc_rotate_tx_rotate() to check there's something to rotate
rxrpc: Fix leak of released call in recvmsg(MSG_PEEK)
rxrpc: Fix socket notification race
rxrpc: Fix potential infinite loop in rxrpc_recvmsg()
rxrpc: Fix oob challenge leak in cleanup after notification failure
rxrpc: Fix the reception of a reply packet before data transmission
afs: Fix uncancelled rxrpc OOB message handler
afs: Fix further netns teardown to cancel the preallocation charger
rxrpc: Fix double unlock in rxrpc_recvmsg()
rxrpc: Fix leak of connection from OOB challenge
rxrpc: Fix ACKALL packet handling
net: hns3: differentiate autoneg default values between copper and fiber
net: hns3: fix permanent link down deadlock after reset
net: hns3: refactor MAC autoneg and speed configuration
net: hns3: unify copper port ksettings configuration path
...
Breno reports following splats on mlx5:
RTNL: assertion failed at net/core/dev.c (2241)
WARNING: net/core/dev.c:2241 at netif_state_change+0xed/0x130, CPU#5: ethtool/1335
RIP: 0010:netif_state_change+0xf9/0x130
Call Trace:
<TASK>
__linkwatch_sync_dev+0xea/0x120
ethtool_op_get_link+0xe/0x20
__ethtool_get_link+0x26/0x40
linkstate_prepare_data+0x51/0x200
ethnl_default_doit+0x213/0x470
genl_family_rcv_msg_doit+0xdd/0x110
Looks like I missed ethtool_op_get_link() trying to sync linkwatch,
which needs rtnl_lock. Not all drivers do this - bnxt doesn't,
it just returns the link state, so add an opt-in bit.
Reported-by: Breno Leitao <leitao@debian.org>
Fixes: 45079e0013 ("net: ethtool: optionally skip rtnl_lock on Netlink path for GET ops")
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Breno Leitao <leitao@debian.org>
Acked-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20260624190439.2521219-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix a link loss issue during driver initialization on optical ports
connected to forced-mode (non-autoneg) remote switches.
Previously, during driver probe or initialization, hclge_configure()
blindly hardcoded hdev->hw.mac.req_autoneg to AUTONEG_ENABLE for all
media types. While this is necessary for copper (BASE-T) ports to
establish a link, many high-speed optical (fiber) ports in data
centers are connected to switches running in forced mode (fixed speed,
autoneg disabled). Forcing autoneg on these optical ports during
initialization causes a permanent link failure since the remote end
refuses to respond to autoneg pulses.
Fix this by implementing media-type differentiated initialization in
hclge_init_ae_dev(). Copper ports continue to default to
AUTONEG_ENABLE, while optical ports strictly inherit the preset
autoneg status pre-configured by the firmware (hdev->hw.mac.autoneg),
preserving native compatibility with forced-mode network environments.
Fixes: 05eb60e964 ("net: hns3: using user configure after hardware reset")
Signed-off-by: Shuaisong Yang <yangshuaisong@h-partners.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20260624141319.271439-5-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix a critical race condition deadlock where the network interface
remains permanently Link Down after a hardware reset under specific
ethtool sequences.
This issue exclusively manifests in firmware-controlled PHY topologies
where the driver relies on the IMP firmware to arbitrate link parameters.
Standard devices driven by the kernel's native PHY_LIB are unaffected.
The deadlock occurs via the following path:
1. User disables autoneg and forces an unmatched speed, forcing link
down: `ethtool -s ethx autoneg off speed 10 duplex full`
2. User re-enables autoneg: `ethtool -s ethx autoneg on`. The netdev
stack passes cmd->base.speed as SPEED_UNKNOWN (0xffffffff).
3. Driver saves req_autoneg=1, but before the interface can link up,
a hardware reset is triggered.
4. During reset recovery, MAC init reads the un-synchronized runtime
state mac.autoneg (which is still 0/OFF), misinterprets it as
forced mode, and pushes the cached SPEED_UNKNOWN into the hardware
registers, causing the MAC firmware state machine to freeze.
Meanwhile, PHY init reads req_autoneg=1 and enables PHY autoneg.
Since the MAC is frozen with 0xffffffff and PHY is running autoneg,
they mismatch permanently.
Fix this by:
1. Intercepting SPEED_UNKNOWN/DUPLEX_UNKNOWN in
hclge_set_phy_link_ksettings() and hclge_cfg_mac_speed_dup_h() to
prevent it from corrupting the driver's cached valid configuration.
2. Save req_autoneg in hclge_set_autoneg().
3. Aligning the state judgment in hclge_set_autoneg_speed_dup() to use
req_autoneg instead of the un-synchronized runtime mac.autoneg,
ensuring both MAC and PHY consistently enter the autoneg branch to
eliminate configuration discrepancies during reset recovery.
Fixes: 05eb60e964 ("net: hns3: using user configure after hardware reset")
Signed-off-by: Shuaisong Yang <yangshuaisong@h-partners.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20260624141319.271439-4-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extract the MAC autoneg and speed/duplex/lane configuration logic out
of hclge_mac_init() and encapsulate it into a new dedicated helper
function hclge_set_autoneg_speed_dup().
In the init path (hclge_init_ae_dev), this helper is now called after
hclge_update_port_info() so that firmware-reported autoneg values are
already populated before applying the link configuration.
Introduce a separate req_lane_num field in struct hclge_mac to isolate
the user-requested lane count from mac.lane_num, which firmware may
overwrite via hclge_get_sfp_info() with stale values from a prior link
lifecycle (e.g., lane_num=4 from 100G). During probe, req_lane_num is
initialized to 0, which instructs firmware to auto-select the correct
lane count for the current speed, rather than reusing the firmware-
reported mac.lane_num that may be inconsistent with the target speed.
This prevents probe failures from mismatched (speed, lane_num) pairs.
In the reset path (hclge_reset_ae_dev), it runs immediately after
hclge_mac_init(), using the previously cached req_* values to restore
the link without re-querying firmware.
Signed-off-by: Shuaisong Yang <yangshuaisong@h-partners.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20260624141319.271439-3-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor hns3_set_link_ksettings() and hclge_set_phy_link_ksettings()
to unify the configuration path for copper ports.
Previously, netdevs with a native kernel phy attached bypassed the main
MAC parameter caching logic and returned early via
phy_ethtool_ksettings_set(). This prevented the driver from updating
hdev->hw.mac.req_xxx variables for kernel PHY setups, leaving them
out-of-sync during reset recovery.
Clean this up by routing all copper port configurations through
ops->set_phy_link_ksettings(), and perform driver-level or kernel-level
PHY arbitration inside hclge_set_phy_link_ksettings() via
hnae3_dev_phy_imp_supported(). This ensures that the user's intended link
profiles (req_speed, req_duplex, req_autoneg) are uniformly recorded
across all copper and fiber deployment topologies, laying the groundwork
for stable reset recovery.
For copper ports where neither IMP firmware nor a kernel PHY is available
(e.g. PHY_INEXISTENT), hclge_set_phy_link_ksettings() returns -ENODEV.
In hns3_set_link_ksettings(), this is caught so the configuration falls
through to the existing MAC-level path (check_ksettings_param ->
cfg_mac_speed_dup_h), preserving compatibility with PHY-less copper
deployments.
Signed-off-by: Shuaisong Yang <yangshuaisong@h-partners.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20260624141319.271439-2-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before the commit 7553911210 ("net: mana: Allocate MSI-X vectors
dynamically"), all the MANA IRQs were assigned statically and together
during early driver load.
After this commit, the IRQ allocation for MANA was done in two phases.
HWC IRQ allocated earlier and then, queue IRQs dynamically added at a
later point. By this time, the IRQ weights on vCPUs can become imbalanced
and if IRQ count is greater than the vCPU count the topology aware IRQ
distribution logic in MANA can cause multiple MANA IRQs to land on the
same vCPUs, while other sibling vCPUs have none (case 1).
On SMP enabled, low-vCPU systems, this becomes a bigger problem as the
softIRQ handling overhead of two IRQs on the same vCPUs becomes much more
than their overheads if they were spread across sibling vCPUs.
In such cases when many parallel TCP connections are tested, the
throughput drops significantly.
Fix the affinity assignment logic, in cases where the IRQ count is greater
than the vCPU count and when IRQs are added dynamically, by utilizing all
the vCPUs irrespective of their NUMA/core bindings (case 2).
The results of setting the affinity and hint to NULL were also studied,
and we observed that, with this logic if there are pre-existing IRQs
allocated on the VM (apart from MANA), during MANA IRQs allocation, it
leads to clustering of the MANA queue IRQs again (case 3).
=======================================================
Case 1: without this patch
=======================================================
4 vcpu(2 cores), 5 MANA IRQs (1 HWC + 4 Queue)
TYPE effective vCPU aff
=======================================================
IRQ0: HWC 0
IRQ1: mana_q1 0
IRQ2: mana_q2 2
IRQ3: mana_q3 0
IRQ4: mana_q4 3
%soft on each vCPU(mpstat -P ALL 1) on receiver
vCPU 0 1 2 3
=======================================================
pass 1: 38.85 0.03 24.89 24.65
pass 2: 39.15 0.03 24.57 25.28
pass 3: 40.36 0.03 23.20 23.17
=======================================================
Case 2: with this patch
=======================================================
4 vcpu(2 cores), 5 MANA IRQs (1 HWC + 4 Queue)
TYPE effective vCPU aff
=======================================================
IRQ0: HWC 0
IRQ1: mana_q1 0
IRQ2: mana_q2 1
IRQ3: mana_q3 2
IRQ4: mana_q4 3
%soft on each vCPU(mpstat -P ALL 1) on receiver
vCPU 0 1 2 3
=======================================================
pass 1: 15.42 15.85 14.99 14.51
pass 2: 15.53 15.94 15.81 15.93
pass 3: 16.41 16.35 16.40 16.36
=======================================================
Case 3: with affinity set to NULL
=======================================================
4 vCPU(2 cores), 5 MANA IRQs (1 HWC + 4 Queue)
TYPE effective vCPU aff
=======================================================
IRQ0: HWC 0
IRQ1: mana_q1 2
IRQ2: mana_q2 3
IRQ3: mana_q3 2
IRQ4: mana_q4 3
=======================================================
Throughput Impact(in Gbps, same env)
=======================================================
TCP conn with patch w/o patch aff NULL
20480 15.65 7.73 5.25
10240 15.63 8.93 5.77
8192 15.64 9.69 7.16
6144 15.64 13.16 9.33
4096 15.69 15.75 13.50
2048 15.69 15.83 13.61
1024 15.71 15.28 13.60
Fixes: 7553911210 ("net: mana: Allocate MSI-X vectors dynamically")
Cc: stable@vger.kernel.org
Co-developed-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
Signed-off-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Yury Norov <ynorov@nvidia.com>
Link: https://patch.msgid.link/20260624072138.1632849-1-shradhagupta@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sparx5_register_notifier_blocks() registers the switchdev blocking
notifier before allocating the ordered workqueue. If the workqueue
allocation fails, the error path unregisters the switchdev and netdevice
notifiers, but leaves the blocking notifier registered.
Add a separate error label for the workqueue allocation failure path and
unregister the switchdev blocking notifier there.
Fixes: d6fce51419 ("net: sparx5: add switching support")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260623115714.2192074-1-haoxiang_li2024@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For i.MX94 series, all the standalone ENETCs do not support SR-IOV, so
pf->caps.num_vsi is zero. This leads to a divide-by-zero in
enetc4_default_rings_allocation() when distributing rings among PF and
VFs.
Division by zero is undefined behavior in C. On ARM64, the UDIV/SDIV
instructions silently return zero rather than raising an exception, so
the issue does not cause a visible crash. However, relying on this
behavior is incorrect and poses a cross-platform compatibility risk.
Add an explicit check for num_vsi == 0 and return early after the PF's
rings have been configured.
Fixes: 2d673b0e2f ("net: enetc: add standalone ENETC support for i.MX94")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260624072726.1238903-1-wei.fang@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2026-06-22 (ice, i40e, e1000e)
For ice:
Dawid changes call to release control VSI during reset to prevent
leaking it.
Lukasz fixes flow control error check to check value rather than treat
is as bitmap values.
Paul makes link related errors non-fatal to probe to allow for recovery
in certain NVM update situations.
Marcin moves netif_keep_dst() to only be called once when entering
switchdev mode.
ZhaoJinming adds a cleanup path for ice_dpll_init_info() to prevent
memory leaks on error path.
For i40e:
Mohamed Khalfella corrects argument passed in macro to match the
one provided to the macro.
For e1000e:
Dima resolves power state issues by adjusting value of PLL clock gate
and re-enabling K1; a quirk table is added to keep it off for known bad
systems.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
e1000e: Reconfigure PLL clock gate timeout and re-enable K1 on Meteor Lake
i40e: Fix i40e_debug() to use struct i40e_hw argument
ice: dpll: fix memory leak in ice_dpll_init_info error paths
ice: dpll: set pointers to NULL after kfree in ice_dpll_deinit_info
ice: call netif_keep_dst() once when entering switchdev mode
ice: fix ice_init_link() error return preventing probe
ice: fix AQ error code comparison in ice_set_pauseparam()
ice: fix FDIR CTRL VSI resource leak in ice_reset_all_vfs()
====================
Link: https://patch.msgid.link/20260622220059.2471844-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mac->phy_node is acquired via of_parse_phandle() in spl2sw_probe() and
stored in the mac private data, transferring ownership of the
device_node reference to mac. On driver removal, spl2sw_phy_remove()
disconnects the PHY but never drops that reference, so each
probe-then-remove cycle leaks one of_node refcount per port permanently.
Drop the reference after phy_disconnect(). While at it, remove the
redundant inner "if (ndev)" check; comm->ndev[i] was just verified
non-NULL on the line above.
Compile-tested only; no SP7021 hardware available.
Fixes: fd3040b939 ("net: ethernet: Add driver for Sunplus SP7021")
Signed-off-by: Shitalkumar Gandhi <shitalkumar.gandhi@cambiumnetworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/f3bdd4c91f3e2269b4e256075f9dc70808b1b8e9.1782195965.git.shitalkumar.gandhi@cambiumnetworks.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
gem_init_one() calls gem_remove_one() when register_netdev() fails.
gem_remove_one() unregisters and frees resources owned by the net_device,
including the DMA block, MMIO mapping, PCI regions, and the net_device
itself. gem_init_one() then falls through to its own cleanup labels and
frees the same resources again.
Keep the register_netdev() error path in gem_init_one(): clear drvdata so
PM/remove paths do not see a half-registered device, remove the NAPI
instance added during probe, and let the existing cleanup labels release
the resources once.
The issue was found by a local static-analysis checker for probe error
paths. The reported path was manually inspected before sending this fix.
Compile-tested with CONFIG_SUNGEM=y. Runtime testing was not performed
because no sungem hardware is available.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Ruoyu Wang <ruoyuw560@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260623025759.3468566-1-ruoyuw560@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Configurations with mlx5 built-in but macsec=m fail to link:
x86_64-linux-ld: drivers/infiniband/hw/mlx5/macsec.o: in function `mlx5r_add_gid_macsec_operations':
macsec.c:(.text+0x77d): undefined reference to `macsec_netdev_is_offloaded'
x86_64-linux-ld: drivers/infiniband/hw/mlx5/macsec.o: in function `mlx5r_del_gid_macsec_operations':
macsec.c:(.text+0xe81): undefined reference to `macsec_netdev_is_offloaded'
Fix the dependency so this configuration cannot happen.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20260622124229.2444502-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
kalmia_rx_fixup() computes usb_packet_length = skb->len - (2 *
KALMIA_HEADER_LENGTH) as a u16, guarded only by a pre-loop check that
skb->len is at least KALMIA_HEADER_LENGTH, which is 6. A device can
deliver a short bulk-IN frame with skb->len in the 6 to 11 range, or
leave a short trailing remainder on a later loop iteration. Either case
underflows usb_packet_length to about 65530.
That bypasses the usb_packet_length < ether_packet_length truncation path.
The device-supplied ether_packet_length, a le16 up to 65535 read from
header_start[2], then drives a memcmp() and the following skb_trim() and
skb_pull() past the end of the rx buffer. The rx buffer is hard_mtu * 10,
which is 14000 bytes. That is an out of bounds read.
Require both the start and end framing headers to be present before
subtracting them, on every loop iteration.
Fixes: d40261236e ("net/usb: Add Samsung Kalmia driver for Samsung GT-B3730")
Cc: stable@vger.kernel.org
Signed-off-by: Maoyi Xie <maoyixie.tju@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/178211531778.2216480.12637613349790980750@maoyixie.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Even with both paths gated on gs->gro_hint, geneve_gro_complete()
re-derives the inner dispatch type and length from the packet and the
current gs->gro_hint, independently of geneve_gro_receive(). The two can
disagree if gs->gro_hint flips under a concurrent geneve_quiesce()/
geneve_unquiesce() (sk_user_data is NULL across a synchronize_net()), or if
the re-read option bytes differ from the ones receive parsed.
geneve_gro_receive() already records the inner network header position in
NAPI_GRO_CB()->inner_network_offset. Have geneve_gro_complete() compute the
offset it is about to dispatch at, adding ETH_HLEN in the ETH_P_TEB case
where eth_gro_complete() steps over the inner MAC header, and bail out if
it lands past inner_network_offset.
Use a lower bound rather than exact equality: between gh_len and the inner
L3 header, geneve_gro_receive() may also have pulled an inner VLAN tag
(vlan_gro_receive() advances the recorded offset past it), which only moves
inner_network_offset further out. A valid frame therefore always satisfies
inner_nh <= inner_network_offset, while a gh_len inflated by a hint
gro_receive() did not honour dispatches past the validated inner header,
i.e. the out-of-bounds completion. Only the latter is rejected.
Fixes: fd0dd79657 ("geneve: use GRO hint option in the RX path")
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Weiming Shi <bestswngs@gmail.com>
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Link: https://patch.msgid.link/20260618032622.484720-2-xmei5@asu.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
geneve_gro_receive() reads the GRO hint through geneve_sk_gro_hint_off(),
which honours it only when the socket enabled IFLA_GENEVE_GRO_HINT
(gs->gro_hint). geneve_gro_complete() instead calls the low-level
geneve_opt_gro_hint_off() and acts on the hint unconditionally.
On a tunnel without the hint, receive aggregates the frames as plain
ETH_P_TEB while complete still honours an attacker-supplied hint option: it
inflates gh_len by gro_hint->nested_hdr_len (u8) and redirects the dispatch
type, so the inner gro_complete handler runs at nhoff + gh_len, an offset
receive never pulled nor validated, reading out of bounds of the skb head:
BUG: KASAN: slab-out-of-bounds in ipv6_gro_complete (net/ipv6/ip6_offload.c:196)
Read of size 1 at addr ffff88800fe91980 by task exploit/153
ipv6_gro_complete (net/ipv6/ip6_offload.c:196)
geneve_gro_complete (drivers/net/geneve.c:965)
udp_gro_complete (net/ipv4/udp_offload.c:940)
inet_gro_complete (net/ipv4/af_inet.c:1621)
__gro_flush (net/core/gro.c:306)
Gate the complete path on gs->gro_hint too via geneve_sk_gro_hint_off(), so
both paths agree. Tunnels that enable the hint are unaffected.
Fixes: fd0dd79657 ("geneve: use GRO hint option in the RX path")
Reported-by: Weiming Shi <bestswngs@gmail.com>
Reported-by: Kyle Zeng <kylebot@openai.com>
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Link: https://patch.msgid.link/20260618032622.484720-1-xmei5@asu.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On Marvell MPIC platforms (Armada 370/XP/38x), mvneta uses a percpu
IRQ disable/enable scheme for NAPI: the ISR (mvneta_percpu_isr) calls
disable_percpu_irq() to mask the MPIC per-CPU interrupt and schedules
NAPI poll, which calls enable_percpu_irq() on completion to unmask.
If suspend occurs while NAPI poll is pending (between
disable_percpu_irq in the ISR and enable_percpu_irq in poll
completion), the interrupt is never re-enabled:
1. mvneta_percpu_isr: disable_percpu_irq() + napi_schedule()
=> MPIC masked, percpu_enabled cpumask bit cleared
2. NAPI poll does not complete before suspend proceeds
(on PREEMPT_RT this is highly likely since softirqs run in
ksoftirqd which gets frozen; on non-RT it can happen when
softirq processing is deferred to ksoftirqd)
3. mvneta_stop_dev => napi_disable(): cancels the pending poll
without executing the completion path
4. suspend_device_irqs => IRQCHIP_MASK_ON_SUSPEND: masks MPIC
(already masked, but records IRQS_SUSPENDED)
5. Resume: mpic_resume checks irq_percpu_is_enabled() => false
(bit was cleared in step 1) => skips unmask
6. mvneta_start_dev only restores device-level INTR_NEW_MASK,
does not touch the MPIC per-CPU mask
Result: MPIC per-CPU interrupt stays masked permanently. The NIC
generates interrupts (INTR_NEW_CAUSE != 0) but the CPU never
receives them, causing complete loss of network connectivity.
Fix by calling on_each_cpu(mvneta_percpu_enable) in the resume path
to unconditionally unmask the MPIC per-CPU interrupt regardless of
pre-suspend state.
Fixes: 12bb03b436 ("net: mvneta: Handle per-cpu interrupts")
Signed-off-by: Yun Zhou <yun.zhou@windriver.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://patch.msgid.link/20260622074350.1666290-1-yun.zhou@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
CGX per-lmac debugfs seq readers obtained struct rvu via
pci_get_drvdata(pci_get_device(..., PCI_DEVID_OCTEONTX2_RVU_AF, ...)),
which leaks a PCI device reference on every read. Store rvu and the CGX
handle in debugfs inode private data when creating stats, mac_filter,
and fwdata files (one context per CGX), and use debugfs aux numbers for
fwdata so lmac_id matches the other CGX debugfs entries.
Fixes: f967488d09 ("octeontx2-af: Add per CGX port level NIX Rx/Tx counters")
Fixes: dbc52debf9 ("octeontx2-af: Debugfs support for DMAC filters")
Fixes: 49f02e6877 ("Octeontx2-af: Debugfs support for firmware data")
Cc: Linu Cherian <lcherian@marvell.com>
Reported-by: Yuho Choi <dbgh9129@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Link: https://patch.msgid.link/20260622034229.2254145-1-rkannoth@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
NIX maximum number of LFs can be set via devlink command
but that can be done before assigning any LFs to a PF/VF.
The condition used to check whether any LFs are assigned is
incorrect. This patch fixes that condition.
Fixes: dd78428786 ("octeontx2-af: Add new devlink param to configure maximum usable NIX block LFs")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://patch.msgid.link/1782082853-6941-1-git-send-email-sbhatta@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When multiple netdevs share a QDMA TX ring and one device is stopped,
netdev_tx_reset_subqueue() zeroes that device's BQL counters while its
pending skbs remain in the shared HW TX ring. When NAPI later completes
those skbs via netdev_tx_completed_queue(), the already-zeroed
dql->num_queued counter underflows.
Fix the issue:
- Remove netdev_tx_reset_subqueue() from airoha_dev_stop() so pending
skbs are completed naturally by NAPI with proper BQL accounting.
- Rework airoha_qdma_tx_cleanup() to disable TX DMA, flush BQL
counters, DMA-unmap and free all pending skbs while skb->dev
references are still valid. Use a per-queue flushing flag checked
under q->lock in airoha_dev_xmit() to prevent races between teardown
and transmit. Call airoha_qdma_stop_napi() before
airoha_qdma_tx_cleanup() at the call sites.
- Move DMA engine start into probe. Split DMA teardown so TX DMA is
disabled in airoha_qdma_tx_cleanup() and RX DMA in
airoha_qdma_cleanup().
- Remove qdma->users counter since DMA lifetime is now tied to
probe/cleanup rather than per-netdev open/stop.
Fixes: a9c2ca61fe ("net: airoha: Support multiple net_devices for a single FE GDM port")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260620-airoha-bql-fixes-v3-1-76b95374e63e@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On RTL8127A connected to a link partner that advertises 10000baseT
speed cannot be changed to anything other than 10000baseT as 10GbE
is always advertised regardless of any setting. Fix this by
clearing MDIO_AN_10GBT_CTRL_ADV10G bit in rtl822x_config_aneg()'s
call to phy_modify_mmd_changed().
Fixes: 83d9623161 ("net: phy: realtek: add RTL8127-internal PHY")
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Jan Klos <honza.klos@gmail.com>
Link: https://patch.msgid.link/20260620011956.37181-1-honza.klos@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
subbank_srch_order[i] is the physical subbank at search-order slot i,
so each subbank's arr_idx must be i (its slot), not
subbank_srch_order[sb->idx]. The old logic mis-keyed xa_sb_free
and broke allocation traversal order.
Populate arr_idx and xa_sb_free in a single pass over the search
order after subbank structs are initialized.
Fixes: 7ac9d4c407 ("octeontx2-af: npc: cn20k: add subbank search order control")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260619095100.1864440-1-rkannoth@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit d7709812e1 ("net: mana: hardening: Validate adapter_mtu from
MANA_QUERY_DEV_CONFIG") rejected any adapter_mtu value smaller than
ETH_MIN_MTU + ETH_HLEN, including 0, returning -EPROTO and failing
mana_probe().
Some older PF firmware versions still in the field report
adapter_mtu as 0 in the MANA_QUERY_DEV_CONFIG response. With the
hardening check in place, the MANA VF driver now fails to load on
those hosts, breaking networking entirely for guests.
MANA hardware always supports the standard Ethernet MTU. Treat a
reported adapter_mtu of 0 as "the PF did not advertise a value" and
fall back to ETH_FRAME_LEN, the same value used for the pre-V2
message version path. Only jumbo frames remain unavailable until
the PF reports a valid MTU.
Other small-but-nonzero bogus values are still rejected, preserving
the original protection against the unsigned-subtraction wrap that
would otherwise let ndev->max_mtu underflow to a huge value.
Fixes: d7709812e1 ("net: mana: hardening: Validate adapter_mtu from MANA_QUERY_DEV_CONFIG")
Signed-off-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260619055348.467224-1-ernis@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Upon an MDIO CRC error mxl862xx_crc_err_work_fn() walks the DSA ports
and closes the CPU port conduits:
dsa_switch_for_each_cpu_port(dp, priv->ds)
dev_close(dp->conduit);
mxl862xx_remove() unregisters the switch before cancelling this work:
set_bit(MXL862XX_FLAG_WORK_STOPPED, &priv->flags);
cancel_delayed_work_sync(&priv->stats_work);
dsa_unregister_switch(ds);
mxl862xx_host_shutdown(priv);
dsa_unregister_switch() frees the dsa_port objects. If a CRC error
schedules the work during teardown it can run after the ports have been
freed and dereference freed memory.
Guard the port walk with MXL862XX_FLAG_WORK_STOPPED, which is already set
before dsa_unregister_switch(). DSA tears the ports down under
rtnl_lock(), so checking the flag under rtnl_lock() means the work either
runs before teardown and sees valid ports, or runs afterwards, observes
the flag and skips the walk. This mirrors the host_flood_work handler,
which skips torn-down ports under rtnl_lock().
Link: https://sashiko.dev/#/patchset/cover.1780968180.git.daniel%40makrotopia.org?part=2
Fixes: a319d0c8c8 ("net: dsa: mxl862xx: add CRC for MDIO communication")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/5e55169926c02f2b914e5ada529d7453b943cda4.1781702256.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MXL862XX_API_* macros pass the address of a stack-allocated, __packed
firmware-ABI struct to mxl862xx_api_wrap() as a void *. The struct has an
alignment of 1, so the compiler is free to place it at an odd address.
mxl862xx_api_wrap() reinterprets that buffer as a __le16 * and accesses it
with data[i], for which the compiler assumes the natural 2-byte alignment
of __le16 and emits aligned 16-bit loads/stores (e.g. lhu/sh on MIPS).
When the buffer lands on an odd address these fault on architectures that
do not support unaligned access, such as MIPS32.
-Waddress-of-packed-member does not catch this: the packed origin is
laundered through the void * parameter, so the cast inside api_wrap looks
alignment-safe to the compiler and no warning is emitted.
Use get_unaligned_le16()/put_unaligned_le16() for the three 16-bit word
accesses. The byte accesses (*(u8 *)&data[i], crc16()) are already safe
and are left unchanged.
Link: https://sashiko.dev/#/patchset/cover.1781319534.git.daniel%40makrotopia.org?part=4
Fixes: 23794bec1c ("net: dsa: add basic initial driver for MxL862xx switches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/599327521db465a534d277de53ab9b6cac01928b.1781702256.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
led_classdev_register_ext() only reads init_data.devicename - it never
stores the pointer. However, the caller allocated devicename with
kasprintf() but never freed it, leaking the string memory.
Fix it with a stack buffer to avoid dynamic buffers completely.
Fixes: 32d6170054 ("net: dsa: realtek: add LED drivers for rtl8366rb")
Signed-off-by: David Yang <mmyangfl@gmail.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260618140200.1888707-1-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ixp4xx_hss_probe() allocates two HDLC netdevs. The first one is stored
in ndev, initialized, and registered with register_hdlc_device(). The
second one is stored in port->netdev and later used by the remove path
for unregister_hdlc_device() and free_netdev().
This means that the registered netdev is not the same object that is
unregistered and freed on remove. It also leaks the first allocation if
the second alloc_hdlcdev() call fails, and the first allocation is not
checked before ndev is used.
Older code allocated the HDLC netdev only once and stored the same object
in both the local variable and port->netdev. The buggy conversion split
this into two alloc_hdlcdev() calls. A later rename changed the local
variable name to ndev, but the underlying mismatch remained.
Fix this by allocating the HDLC netdev only once and assigning the same
object to port->netdev.
Fixes: 99ebe65eb9 ("net: ixp4xx_hss: move out assignment in if condition")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260622043015.643637-1-haoxiang_li2024@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
airoha_tc_htb_alloc_leaf_queue() assigns queue IDs based on the channel
index (opt->qid = AIROHA_NUM_TX_RING + channel), but updates
real_num_tx_queues with a simple increment (num_tx_queues + 1). When QoS
channels are allocated sparsely (e.g., channels 0 and 3 without 1 and
2), the returned qid can exceed real_num_tx_queues, causing out-of-bounds
accesses in the networking stack.
For example, allocating channel 0 then channel 3 results in
real_num_tx_queues = 34 but qid = 35, which is out of range [0, 34).
Fix this by computing real_num_tx_queues based on the highest active
channel index rather than using a simple counter, in both the allocation
and deletion paths.
Fixes: ef1ca92713 ("net: airoha: Add sched HTB offload support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260619-airoha-qos-fixes-v2-2-5c43485038f9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
airoha_tc_htb_alloc_leaf_queue() computes the HTB QoS channel index
as opt->classid % AIROHA_NUM_QOS_CHANNELS and stores it in qos_sq_bmap.
However, airoha_tc_remove_htb_queue() clears the HTB configuration
using queue + 1 as the channel index, causing an off-by-one error.
Use queue directly as the QoS channel index to match the allocation
logic.
Fixes: ef1ca92713 ("net: airoha: Add sched HTB offload support")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260619-airoha-qos-fixes-v2-1-5c43485038f9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When requesting ownership of the NIC (MAC/PHY control), we set up
the heartbeat to look stale:
/* Initialize heartbeat, set last response to 1 second in the past
* so that we will trigger a timeout if the firmware doesn't respond
*/
fbd->last_heartbeat_response = req_time - HZ;
fbd->last_heartbeat_request = req_time;
The response handler then sets:
fbd->last_heartbeat_response = jiffies;
for which we wait via:
fbnic_fw_init_heartbeat() -> fbnic_fw_heartbeat_current()
The scheme is a bit odd, but it should work in principle.
Fix the ordering of operations. We have to set up the stale heartbeat
before we send the message. Otherwise if the response is very fast
we will override it. This triggers on QEMU if we run on the core
that handles the IRQ, and results in ndo_open failing with ETIMEDOUT.
The change in ordering doesn't impact releasing the ownership.
Both ndo_stop and heartbeat check are under rtnl_lock.
Fixes: 20d2e88cc7 ("eth: fbnic: Add initial messaging to notify FW of our presence")
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://patch.msgid.link/20260622154753.827506-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
au1000_close() calls free_irq() while aup->lock is still held with
spin_lock_irqsave(). free_irq() can sleep because it takes the IRQ
descriptor request mutex, so it does not belong inside the close-time
spinlocked section.
This was found by our static analysis tool and then confirmed by manual
review of the in-tree au1000_close() .ndo_stop path. The reviewed path
keeps aup->lock held across the MAC reset, queue stop and
free_irq(dev->irq, dev).
A directed runtime validation kept that ndo_stop carrier and the same
free_irq(dev->irq, dev) operation under the driver lock. Lockdep reported
"BUG: sleeping function called from invalid context" and "Invalid wait
context" while free_irq() was taking desc->request_mutex, with
au1000_close() and free_irq() on the stack.
Drop aup->lock before freeing the IRQ. The protected close-time work still
stops the device and queue before IRQ teardown, but the sleepable IRQ core
path now runs outside the spinlocked section.
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260619151816.1144289-1-runyu.xiao@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Configured VLANs intermittently stop receiving traffic after a link
down/up cycle, e.g. when the network cable is unplugged and plugged back
in. VLAN filtering stays enabled but all VLAN-tagged frames are dropped
until a VLAN is added or removed again.
The LAN7801 datasheet (DS00002123E) states:
"A portion of the MAC operates on clocks generated by the Ethernet
PHY. During a PHY reset event, this portion of the MAC is designed to
not be taken out of reset until the PHY clocks are operational"
(section 8.10, MAC Reset Watchdog Timer)
"After a reset event, the RFE will automatically initialize the
contents of the VHF to 0h."
(section 7.1.4, VHF Organization)
Thus a link down/up cycle stops and restarts the PHY clock, resets the
PHY-clocked portion of the MAC, and the RFE clears its VLAN/DA hash
filter (VHF) memory. The VHF holds both the VLAN filter table and the
multicast hash table, but the driver never reprograms either from its
shadow copy once the link is back, so both stay empty.
Reprogram the VLAN filter and multicast hash tables on link up.
Reported-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Closes: https://lore.kernel.org/netdev/BEZP281MB224501E38B30BFDC4BD3D364D9E32@BEZP281MB2245.DEUP281.PROD.OUTLOOK.COM/T/#u
Tested-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260622102911.484045-1-nb@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During XDP enablement in veth, if xdp_rxq_info_reg() or
xdp_rxq_info_reg_mem_model() fails, the driver rolls back the changes.
However, the rollback loop:
for (i--; i >= start; i--) {
decrements the loop index 'i' before the first iteration. This
correctly skips unregistering the rxq for the failed index 'i' (as
registration failed or was already cleaned up), but it also
erroneously skips calling netif_napi_deli() for rq[i].xdp_napi.
Since netif_napi_add() was already called for index 'i', this leaves
a dangling napi_struct in the device's napi_list. When the veth
device is later destroyed, the freed queue memory (which contains the
leaked NAPI structure) can be reused.
The subsequent device teardown iterates the NAPI list and
corrupts the reallocated memory, leading to UAF.
Fix this by explicitly deleting the NAPI association for the failed
index 'i' before rolling back the successfully configured queues.
Fixes: b02e5a0ebb ("xsk: Propagate napi_id to XDP socket Rx path")
Reported-by: Guenter Roeck <groeck@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://patch.msgid.link/20260622111825.88337-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
emac_xsk_xmit_zc() handles tx xmit for zero copy and gets called
inside napi context. User application wakes up the kernel while
initiating the transmit which triggers napi to start processing
the tx packets. The num_tx check inside emac_tx_complete_packets()
returns early if no packet transfer happen hindering the call
to emac_xsk_xmit_zc(). Remove this check to let application
wakeup initiate zero copy xmit traffic.
Add __netif_tx_lock() to ensure that the TX queue is protected
from concurrent access during the transmission of XDP frames.
This fixes netdev watchdog timeout for long runs.
Fixes: e2dc7bfd67 ("net: ti: icssg-prueth: Move common functions into a separate file")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Link: https://patch.msgid.link/20260618100348.2209907-1-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pin_duration is converted from the user-provided period to SJA1105
clock ticks and is later passed as the cycle_time argument to
future_base_time().
Very small period values may become zero after the conversion,
which can lead to a division by zero in future_base_time().
Round zero pin_duration up to 1 tick so that the smallest unsupported
periods use the minimum non-zero hardware duration instead of passing
zero to future_base_time().
Fixes: 747e5eb31d ("net: dsa: sja1105: configure the PTP_CLK pin as EXT_TS or PER_OUT")
Signed-off-by: Aleksandrova Alyona <aga@itb.spb.ru>
Link: https://patch.msgid.link/20260618110508.53094-1-aga@itb.spb.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In airoha_qdma_set_chan_tx_sched(), the loop clearing queue mask was
using AIROHA_NUM_TX_RING (32) instead of AIROHA_NUM_QOS_QUEUES (8).
Each channel has 8 queues, and TXQ_DISABLE_CHAN_QUEUE_MASK(channel, i)
computes BIT(i + (channel * 8)). With i ranging 0..31, this causes:
- channel 0: clears bit 0..31 (all 4 channels) instead of 0..7
- channel 1: clears bit 8..31 (channels 1-3) instead of 8..15
- channel 2: clears bit 16..31 (channels 2-3) instead of 16..23
- channel 3: clears bit 24..31 (channel 3 only) - correct by accident
While BIT(32+) on arm64 produces 64-bit values truncated to 0 in u32
mask parameter, the loop still incorrectly clears queues within the
same channel beyond queue 7.
Even though this is functionally harmless (the register resets to 0
and is only ever cleared, never set — so clearing extra bits is a
no-op), the loop bound is semantically wrong and should be fixed for
correctness and clarity.
Fix by using AIROHA_NUM_QOS_QUEUES (8) as the loop upper bound.
Fixes: ef1ca92713 ("net: airoha: Add sched HTB offload support")
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Wayen Yan <win847@gmail.com>
Link: https://patch.msgid.link/178187479434.2400840.1312143943526335838@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kernel selftests wait 1.25x of the promised stats refresh time
(as read from ethtool -c). bnxt reports 1sec by default, but
the stats update process has two steps. First device DMAs the
new values, then the service task performs update in full-width
SW counters. So the worst case delay is actually 2x.
Note that the behavior is different for ring stats and port stats.
Port stats are fetched synchronously by the service worker, so
there's no risk of doubling up the delay there.
The problem of stale stats impacts not only tests but real workloads
which monitor egress bandwidth of a NIC. The inaccuracy causes double
counting in the next cycle and spurious overload alarms.
Try to read from the DMA buffer more aggressively, to mitigate
timing issues between DMA and service task. The SW update should
be cheap.
Fixes: 51f307856b ("bnxt_en: Allow statistics DMA to be configurable using ethtool -C.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20260619191538.104165-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Each PPP control protocol (LCP/IPCP/IPV6CP) embedded in struct ppp
registers a timer via timer_setup(). That struct ppp is the
hdlc->state allocation, which detach_hdlc_protocol() frees with kfree()
in both teardown paths: unregister_hdlc_device() and the re-attach inside
attach_hdlc_protocol().
The ppp proto never registered a .detach callback, so
detach_hdlc_protocol() performs no timer synchronization before the
kfree(). The only cancel, timer_delete(&proto->timer) in ppp_cp_event(),
is partial (it does not wait for a running callback) and only runs on the
->CLOSED transition; ppp_stop()/ppp_close() do not sync either. A
ppp_timer callback already executing (blocked on ppp->lock) survives the
kfree and then dereferences proto->state / ppp->lock in freed memory,
leading to a use-after-free.
Fix this by adding a .detach helper that calls timer_shutdown_sync() on
every per-proto timer. detach_hdlc_protocol() invokes proto->detach(dev)
before kfree(hdlc->state), so timer_shutdown_sync()
now runs on both free paths.
timer_shutdown_sync() is used instead of timer_delete_sync() because the
keepalive path re-arms the timer through add_timer()/mod_timer() and
shutdown blocks any re-activation during teardown.
Initialize the per-protocol timers in ppp_ioctl() when the protocol is
attached, and remove the now-redundant timer_setup() from ppp_start(), so
that the timers are initialized exactly once at attach time and
ppp_timer_release() never operates on uninitialized timer_list
structures. attach_hdlc_protocol() uses kmalloc() (not kzalloc), so
struct ppp's protos[i].timer is uninitialized garbage until the first
timer_setup(); without this init-at-attach, attaching the PPP protocol
without ever bringing the device up would leave timer_shutdown_sync()
operating on uninitialized memory in .detach. Moving the init out of
ppp_start() (which only runs on NETDEV_UP) into the attach path makes the
initialization unconditional and avoids initializing the same timer_list
twice.
This bug was found by static analysis.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Link: https://patch.msgid.link/20260617020518.116319-1-fanwu01@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
icssg_ndo_get_stats64() unconditionally calls emac_get_stat_by_name()
with FW PA stat names regardless of whether the PA stats block is
present on the hardware. emac_get_stat_by_name() already guards the
PA stats lookup with `if (emac->prueth->pa_stats)`; when that pointer
is NULL the lookup falls through to netdev_err() and returns -EINVAL.
Because ndo_get_stats64 is polled regularly by the networking stack
this produces thousands of log entries of the form:
icssg-prueth icssg1-eth end0: Invalid stats FW_RX_ERROR
A secondary consequence is that the int(-EINVAL) return value is
implicitly widened to a near-ULLONG_MAX unsigned value when accumulated
into the __u64 fields of rtnl_link_stats64, silently corrupting the
rx_errors, rx_dropped and tx_dropped counters reported by `ip -s link`.
Every other PA-aware code path in the driver is already guarded with
the same `if (emac->prueth->pa_stats)` check. Apply the same guard
here.
Fixes: 0d15a26b24 ("net: ti: icssg-prueth: Add ICSSG FW Stats")
Signed-off-by: Philippe Schenker <philippe.schenker@impulsing.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Cc: danishanwar@ti.com
Cc: rogerq@kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260618093037.3448858-1-dev@pschenker.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
i40e_debug() macro takes struct i40e_hw *h as first argument. But the
macro body uses hw instead of h. This has been working so far because hw
happens to be the name of the variable in the context where the macro is
expanded. Fix the macro to use the passed argument.
Fixes: 5dfd37c37a ("i40e: Split i40e_osdep.h")
Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Several error return paths in ice_dpll_init_info() directly return
without freeing previously allocated resources, causing memory leaks:
- When de->input_prio allocation fails, d->inputs is leaked
- When dp->input_prio allocation fails, d->inputs and de->input_prio
are leaked
- When ice_get_cgu_rclk_pin_info() fails, all previously allocated
inputs/outputs/input_prio are leaked
- When ice_dpll_init_pins_info(RCLK_INPUT) fails, same resources
are leaked
Fix this by jumping to the deinit_info label which properly calls
ice_dpll_deinit_info() to free all allocated resources.
Fixes: d7999f5ea6 ("ice: implement dpll interface to control cgu")
Signed-off-by: ZhaoJinming <zhaojinming@uniontech.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice_dpll_deinit_info() calls kfree() on several pf->dplls fields
(inputs, outputs, eec.input_prio, pps.input_prio) but does not set
the pointers to NULL afterward. This leaves dangling pointers in the
pf->dplls structure.
While not currently exploitable through existing code paths, this is
unsafe because:
1. If ice_dpll_init_info() is called again after a deinit (e.g. during
driver recovery), and a subsequent allocation within init fails, the
error path will jump to deinit_info and call ice_dpll_deinit_info()
again. Since some pointers still hold the old freed addresses, this
would result in a double-free.
2. Any future code that checks these pointers before use or after free
would be unprotected against use-after-free.
Follow the common kernel convention of setting pointers to NULL after
kfree() so that:
- kfree(NULL) is a safe no-op, preventing double-free
- NULL checks on these pointers become meaningful
This is a preparatory fix for a subsequent patch that routes additional
error paths in ice_dpll_init_info() to the deinit_info label.
Fixes: d7999f5ea6 ("ice: implement dpll interface to control cgu")
Signed-off-by: ZhaoJinming <zhaojinming@uniontech.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
