Currently, addresses are chunk size aligned. This means, we are very
restricted in terms of where we can place chunk within the umem. For
example, if we have a chunk size of 2k, then our chunks can only be placed
at 0,2k,4k,6k,8k... and so on (ie. every 2k starting from 0).
This patch introduces the ability to use unaligned chunks. With these
changes, we are no longer bound to having to place chunks at a 2k (or
whatever your chunk size is) interval. Since we are no longer dealing with
aligned chunks, they can now cross page boundaries. Checks for page
contiguity have been added in order to keep track of which pages are
followed by a physically contiguous page.
Signed-off-by: Kevin Laatz <kevin.laatz@intel.com>
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Introduce BPF_F_TEST_STATE_FREQ flag to stress test parentage chain
and state pruning.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
I opened /sys/kernel/tracing/trace once and kept reading from it.
bpf_trace_printk somehow did not seem to work, no entries were appended
to that trace file. It turns out that tracing is disabled when that file
is open. Save the next person some time and document this.
The trace file is described in Documentation/trace/ftrace.rst, however
the implication "tracing is disabled" did not immediate translate to
"bpf_trace_printk silently discards entries".
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add a new command for the bpf() system call: BPF_BTF_GET_NEXT_ID is used
to cycle through all BTF objects loaded on the system.
The motivation is to be able to inspect (list) all BTF objects presents
on the system.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When an AF_XDP socket is released/closed the XSKMAP still holds a
reference to the socket in a "released" state. The socket will still
use the netdev queue resource, and block newly created sockets from
attaching to that queue, but no user application can access the
fill/complete/rx/tx queues. This results in that all applications need
to explicitly clear the map entry from the old "zombie state"
socket. This should be done automatically.
In this patch, the sockets tracks, and have a reference to, which maps
it resides in. When the socket is released, it will remove itself from
all maps.
Suggested-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add new helper bpf_sk_storage_clone which optionally clones sk storage
and call it from sk_clone_lock.
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Rename existing bpf_map_inc_not_zero to __bpf_map_inc_not_zero to
indicate that it's caller's responsibility to do proper locking.
Create and export bpf_map_inc_not_zero wrapper that properly
locks map_idr_lock. Will be used in the next commit to
hold a map while cloning a socket.
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This commit adds support for a new flag called need_wakeup in the
AF_XDP Tx and fill rings. When this flag is set, it means that the
application has to explicitly wake up the kernel Rx (for the bit in
the fill ring) or kernel Tx (for bit in the Tx ring) processing by
issuing a syscall. Poll() can wake up both depending on the flags
submitted and sendto() will wake up tx processing only.
The main reason for introducing this new flag is to be able to
efficiently support the case when application and driver is executing
on the same core. Previously, the driver was just busy-spinning on the
fill ring if it ran out of buffers in the HW and there were none on
the fill ring. This approach works when the application is running on
another core as it can replenish the fill ring while the driver is
busy-spinning. Though, this is a lousy approach if both of them are
running on the same core as the probability of the fill ring getting
more entries when the driver is busy-spinning is zero. With this new
feature the driver now sets the need_wakeup flag and returns to the
application. The application can then replenish the fill queue and
then explicitly wake up the Rx processing in the kernel using the
syscall poll(). For Tx, the flag is only set to one if the driver has
no outstanding Tx completion interrupts. If it has some, the flag is
zero as it will be woken up by a completion interrupt anyway.
As a nice side effect, this new flag also improves the performance of
the case where application and driver are running on two different
cores as it reduces the number of syscalls to the kernel. The kernel
tells user space if it needs to be woken up by a syscall, and this
eliminates many of the syscalls.
This flag needs some simple driver support. If the driver does not
support this, the Rx flag is always zero and the Tx flag is always
one. This makes any application relying on this feature default to the
old behaviour of not requiring any syscalls in the Rx path and always
having to call sendto() in the Tx path.
For backwards compatibility reasons, this feature has to be explicitly
turned on using a new bind flag (XDP_USE_NEED_WAKEUP). I recommend
that you always turn it on as it so far always have had a positive
performance impact.
The name and inspiration of the flag has been taken from io_uring by
Jens Axboe. Details about this feature in io_uring can be found in
http://kernel.dk/io_uring.pdf, section 8.3.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This commit replaces ndo_xsk_async_xmit with ndo_xsk_wakeup. This new
ndo provides the same functionality as before but with the addition of
a new flags field that is used to specifiy if Rx, Tx or both should be
woken up. The previous ndo only woke up Tx, as implied by the
name. The i40e and ixgbe drivers (which are all the supported ones)
are updated with this new interface.
This new ndo will be used by the new need_wakeup functionality of XDP
sockets that need to be able to wake up both Rx and Tx driver
processing.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
1) Rename mss field to mss_option field in synproxy, from Fernando Mancera.
2) Use SYSCTL_{ZERO,ONE} definitions in conntrack, from Matteo Croce.
3) More strict validation of IPVS sysctl values, from Junwei Hu.
4) Remove unnecessary spaces after on the right hand side of assignments,
from yangxingwu.
5) Add offload support for bitwise operation.
6) Extend the nft_offload_reg structure to store immediate date.
7) Collapse several ip_set header files into ip_set.h, from
Jeremy Sowden.
8) Make netfilter headers compile with CONFIG_KERNEL_HEADER_TEST=y,
from Jeremy Sowden.
9) Fix several sparse warnings due to missing prototypes, from
Valdis Kletnieks.
10) Use static lock initialiser to ensure connlabel spinlock is
initialized on boot time to fix sched/act_ct.c, patch
from Florian Westphal.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
So far phy_speed_down/up can be used up to 1Gbps only. Remove this
restriction by using new helper __phy_speed_down. New member adv_old
in struct phy_device is used by phy_speed_up to restore the advertised
modes before calling phy_speed_down. Don't simply advertise what is
supported because a user may have intentionally removed modes from
advertisement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
phy_speed_down_core provides most of the functionality for
phy_speed_down. It makes use of new helper phy_resolve_min_speed that is
based on the sorting of the settings[] array. In certain cases it may be
helpful to be able to exclude legacy half duplex modes, therefore
prepare phy_resolve_min_speed() for it.
v2:
- rename __phy_speed_down to phy_speed_down_core
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Daniel Borkmann says:
====================
The following pull-request contains BPF updates for your *net-next* tree.
There is a small merge conflict in libbpf (Cc Andrii so he's in the loop
as well):
for (i = 1; i <= btf__get_nr_types(btf); i++) {
t = (struct btf_type *)btf__type_by_id(btf, i);
if (!has_datasec && btf_is_var(t)) {
/* replace VAR with INT */
t->info = BTF_INFO_ENC(BTF_KIND_INT, 0, 0);
<<<<<<< HEAD
/*
* using size = 1 is the safest choice, 4 will be too
* big and cause kernel BTF validation failure if
* original variable took less than 4 bytes
*/
t->size = 1;
*(int *)(t+1) = BTF_INT_ENC(0, 0, 8);
} else if (!has_datasec && kind == BTF_KIND_DATASEC) {
=======
t->size = sizeof(int);
*(int *)(t + 1) = BTF_INT_ENC(0, 0, 32);
} else if (!has_datasec && btf_is_datasec(t)) {
>>>>>>> 72ef80b5ee
/* replace DATASEC with STRUCT */
Conflict is between the two commits 1d4126c4e1 ("libbpf: sanitize VAR to
conservative 1-byte INT") and b03bc6853c ("libbpf: convert libbpf code to
use new btf helpers"), so we need to pick the sanitation fixup as well as
use the new btf_is_datasec() helper and the whitespace cleanup. Looks like
the following:
[...]
if (!has_datasec && btf_is_var(t)) {
/* replace VAR with INT */
t->info = BTF_INFO_ENC(BTF_KIND_INT, 0, 0);
/*
* using size = 1 is the safest choice, 4 will be too
* big and cause kernel BTF validation failure if
* original variable took less than 4 bytes
*/
t->size = 1;
*(int *)(t + 1) = BTF_INT_ENC(0, 0, 8);
} else if (!has_datasec && btf_is_datasec(t)) {
/* replace DATASEC with STRUCT */
[...]
The main changes are:
1) Addition of core parts of compile once - run everywhere (co-re) effort,
that is, relocation of fields offsets in libbpf as well as exposure of
kernel's own BTF via sysfs and loading through libbpf, from Andrii.
More info on co-re: http://vger.kernel.org/bpfconf2019.html#session-2
and http://vger.kernel.org/lpc-bpf2018.html#session-2
2) Enable passing input flags to the BPF flow dissector to customize parsing
and allowing it to stop early similar to the C based one, from Stanislav.
3) Add a BPF helper function that allows generating SYN cookies from XDP and
tc BPF, from Petar.
4) Add devmap hash-based map type for more flexibility in device lookup for
redirects, from Toke.
5) Improvements to XDP forwarding sample code now utilizing recently enabled
devmap lookups, from Jesper.
6) Add support for reporting the effective cgroup progs in bpftool, from Jakub
and Takshak.
7) Fix reading kernel config from bpftool via /proc/config.gz, from Peter.
8) Fix AF_XDP umem pages mapping for 32 bit architectures, from Ivan.
9) Follow-up to add two more BPF loop tests for the selftest suite, from Alexei.
10) Add perf event output helper also for other skb-based program types, from Allan.
11) Fix a co-re related compilation error in selftests, from Yonghong.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
A number of non-UAPI Netfilter header-files contained superfluous
"#ifdef __KERNEL__" guards. Removed them.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
linux/netfilter.h defines a number of struct and inline function
definitions which are only available is CONFIG_NETFILTER is enabled.
These structs and functions are used in declarations and definitions in
other header-files. Added preprocessor checks to make sure these
headers will compile if CONFIG_NETFILTER is disabled.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
struct nf_conn contains a "struct nf_conntrack ct_general" member and
struct net contains a "struct netns_ct ct" member which are both only
defined in CONFIG_NF_CONNTRACK is enabled. These members are used in a
number of inline functions defined in other header-files. Added
preprocessor checks to make sure the headers will compile if
CONFIG_NF_CONNTRACK is disabled.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_tables.h defines an API comprising several inline functions and
macros that depend on the nft member of struct net. However, this is
only defined is CONFIG_NF_TABLES is enabled. Added preprocessor checks
to ensure that nf_tables.h will compile if CONFIG_NF_TABLES is disabled.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
br_netfilter.h defines inline functions that use an enum constant and
struct member that are only defined if CONFIG_BRIDGE_NETFILTER is
enabled. Added preprocessor checks to ensure br_netfilter.h will
compile if CONFIG_BRIDGE_NETFILTER is disabled.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A number of netfilter header-files used declarations and definitions
from other headers without including them. Added include directives to
make those declarations and definitions available.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
linux/netfilter/ipset/ip_set.h included four other header files:
include/linux/netfilter/ipset/ip_set_comment.h
include/linux/netfilter/ipset/ip_set_counter.h
include/linux/netfilter/ipset/ip_set_skbinfo.h
include/linux/netfilter/ipset/ip_set_timeout.h
Of these the first three were not included anywhere else. The last,
ip_set_timeout.h, was included in a couple of other places, but defined
inline functions which call other inline functions defined in ip_set.h,
so ip_set.h had to be included before it.
Inlined all four into ip_set.h, and updated the other files that
included ip_set_timeout.h.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Store immediate data into offload context register. This allows follow
up instructions to take it from the corresponding source register.
This patch is required to support for payload mangling, although other
instructions that take data from source register will benefit from this
too.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add helper function phy_modify_paged_changed, behavios is the same
as for phy_modify_changed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The integrated PHY in 2.5Gbps chip RTL8125 is the first (known to me)
PHY that uses standard Clause 22 for all modes up to 1Gbps and adds
2.5Gbps control using vendor-specific registers. To use phylib for
the standard part little extensions are needed:
- Move most of genphy_config_aneg to a new function
__genphy_config_aneg that takes a parameter whether restarting
auto-negotiation is needed (depending on whether content of
vendor-specific advertisement register changed).
- Don't clear phydev->lp_advertising in genphy_read_status so that
we can set non-C22 mode flags before.
Basically both changes mimic the behavior of the equivalent Clause 45
functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch made the length of the per-CPU skb drop list
configurable. Expose a counter that shows how many packets could not be
enqueued to this list.
This allows users determine the desired queue length.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In packet alert mode, each CPU holds a list of dropped skbs that need to
be processed in process context and sent to user space. To avoid
exhausting the system's memory the maximum length of this queue is
currently set to 1000.
Allow users to tune the length of this queue according to their needs.
The configured length is reported to user space when drop monitor
configuration is queried.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Users should be able to query the current configuration of drop monitor
before they start using it. Add a command to query the existing
configuration which currently consists of alert mode and packet
truncation length.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending dropped packets to user space it is not always necessary to
copy the entire packet as usually only the headers are of interest.
Allow user to specify the truncation length and add the original length
of the packet as additional metadata to the netlink message.
By default no truncation is performed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far drop monitor supported only one alert mode in which a summary of
locations in which packets were recently dropped was sent to user space.
This alert mode is sufficient in order to understand that packets were
dropped, but lacks information to perform a more detailed analysis.
Add a new alert mode in which the dropped packet itself is passed to
user space along with metadata: The drop location (as program counter
and resolved symbol), ingress netdevice and drop timestamp. More
metadata can be added in the future.
To avoid performing expensive operations in the context in which
kfree_skb() is invoked (can be hard IRQ), the dropped skb is cloned and
queued on per-CPU skb drop list. Then, in process context the netlink
message is allocated, prepared and finally sent to user space.
The per-CPU skb drop list is limited to 1000 skbs to prevent exhausting
the system's memory. Subsequent patches will make this limit
configurable and also add a counter that indicates how many skbs were
tail dropped.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next patch is going to add another alert mode in which the dropped
packet is notified to user space, instead of only a summary of recent
drops.
Abstract the differences between the modes by adding alert mode
operations. The operations are selected based on the currently
configured mode and associated with the probes and the work item just
before tracing starts.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
This cleans up a lot of unneeded code and logic around the debugfs
files, making all of this much simpler and easier to understand as we
don't need to keep the dentries saved anymore.
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
This cleans up a lot of unneeded code and logic around the debugfs wimax
files, making all of this much simpler and easier to understand.
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: linux-wimax@intel.com
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mlx5_eswitch_rep stores same hw ID for all representors.
However it is never used from this structure.
It is always used from mlx5_vport.
Hence, remove unused field.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
To remove dependency on rtnl lock, protect mod_hdr hash table from
concurrent modifications with new mutex.
Implement helper function to get flow namespace to prevent code
duplication.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
List of flows attached to mod header entry is used as implicit reference
counter (mod header entry is deallocated when list becomes free) and as a
mechanism to obtain mod header entry that flow is attached to (through list
head). This is not safe when concurrent modification of list of flows
attached to mod header entry is possible. Proper atomic reference counter
is required to support concurrent access.
As a preparation for extending mod header with reference counting, extract
code that lookups and deletes mod header entry into standalone put/get
helpers. In order to remove this dependency on external locking, extend mod
header entry with reference counter to manage its lifetime and extend flow
structure with direct pointer to mod header entry that flow is attached to.
To remove code duplication between legacy and switchdev mode
implementations that both support mod_hdr functionality, store mod_hdr
table in dedicated structure used by both fdb and kernel namespaces. New
table structure is extended with table lock by one of the following patches
in this series. Implement helper function to get correct mod_hdr table
depending on flow namespace.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current implementation of TCP MTU probing can considerably
underestimate the MTU on lossy connections allowing the MSS to get down to
48. We have found that in almost all of these cases on our networks these
paths can handle much larger MTUs meaning the connections are being
artificially limited. Even though TCP MTU probing can raise the MSS back up
we have seen this not to be the case causing connections to be "stuck" with
an MSS of 48 when heavy loss is present.
Prior to pushing out this change we could not keep TCP MTU probing enabled
b/c of the above reasons. Now with a reasonble floor set we've had it
enabled for the past 6 months.
The new sysctl will still default to TCP_MIN_SND_MSS (48), but gives
administrators the ability to control the floor of MSS probing.
Signed-off-by: Josh Hunt <johunt@akamai.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of the snapshot has to be the same as the size of the region,
therefore no need to pass it again during snapshot creation. Remove the
arg and use region->size instead.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the RSS functionality and add the corresponding callbacks in
XGMAC core.
Changes from v1:
- Do not use magic constants (Jakub)
- Use ethtool_rxfh_indir_default() (Jakub)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
move tc indirect block to flow_offload and rename
it to flow indirect block.The nf_tables can use the
indr block architecture.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When GRO decides not to coalesce a packet, in napi_frags_finish(), instead
of passing it to the stack immediately, place it on a list in the napi
struct. Then, at flush time (napi_complete_done(), napi_poll(), or
napi_busy_loop()), call netif_receive_skb_list_internal() on the list.
We'd like to do that in napi_gro_flush(), but it's not called if
!napi->gro_bitmask, so we have to do it in the callers instead. (There are
a handful of drivers that call napi_gro_flush() themselves, but it's not
clear why, or whether this will affect them.)
Because a full 64 packets is an inefficiently large batch, also consume the
list whenever it exceeds gro_normal_batch, a new net/core sysctl that
defaults to 8.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supported ports in ethtool <eth1> are displayed based on media type.
For media type fibre and twinaxial, port type is "FIBRE". Media type
Base-T is "TP" and media KR is "Backplane".
V1->V2:
Corrected the subject.
Signed-off-by: Rahul Verma <rahulv@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Yeah I should have sent a pull request last week, so there is a lot
more here than usual:
1) Fix memory leak in ebtables compat code, from Wenwen Wang.
2) Several kTLS bug fixes from Jakub Kicinski (circular close on
disconnect etc.)
3) Force slave speed check on link state recovery in bonding 802.3ad
mode, from Thomas Falcon.
4) Clear RX descriptor bits before assigning buffers to them in
stmmac, from Jose Abreu.
5) Several missing of_node_put() calls, mostly wrt. for_each_*() OF
loops, from Nishka Dasgupta.
6) Double kfree_skb() in peak_usb can driver, from Stephane Grosjean.
7) Need to hold sock across skb->destructor invocation, from Cong
Wang.
8) IP header length needs to be validated in ipip tunnel xmit, from
Haishuang Yan.
9) Use after free in ip6 tunnel driver, also from Haishuang Yan.
10) Do not use MSI interrupts on r8169 chips before RTL8168d, from
Heiner Kallweit.
11) Upon bridge device init failure, we need to delete the local fdb.
From Nikolay Aleksandrov.
12) Handle erros from of_get_mac_address() properly in stmmac, from
Martin Blumenstingl.
13) Handle concurrent rename vs. dump in netfilter ipset, from Jozsef
Kadlecsik.
14) Setting NETIF_F_LLTX on mac80211 causes complete breakage with
some devices, so revert. From Johannes Berg.
15) Fix deadlock in rxrpc, from David Howells.
16) Fix Kconfig deps of enetc driver, we must have PHYLIB. From Yue
Haibing.
17) Fix mvpp2 crash on module removal, from Matteo Croce.
18) Fix race in genphy_update_link, from Heiner Kallweit.
19) bpf_xdp_adjust_head() stopped working with generic XDP when we
fixes generic XDP to support stacked devices properly, fix from
Jesper Dangaard Brouer.
20) Unbalanced RCU locking in rt6_update_exception_stamp_rt(), from
David Ahern.
21) Several memory leaks in new sja1105 driver, from Vladimir Oltean"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (214 commits)
net: dsa: sja1105: Fix memory leak on meta state machine error path
net: dsa: sja1105: Fix memory leak on meta state machine normal path
net: dsa: sja1105: Really fix panic on unregistering PTP clock
net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as well
net: dsa: sja1105: Fix broken learning with vlan_filtering disabled
net: dsa: qca8k: Add of_node_put() in qca8k_setup_mdio_bus()
net: sched: sample: allow accessing psample_group with rtnl
net: sched: police: allow accessing police->params with rtnl
net: hisilicon: Fix dma_map_single failed on arm64
net: hisilicon: fix hip04-xmit never return TX_BUSY
net: hisilicon: make hip04_tx_reclaim non-reentrant
tc-testing: updated vlan action tests with batch create/delete
net sched: update vlan action for batched events operations
net: stmmac: tc: Do not return a fragment entry
net: stmmac: Fix issues when number of Queues >= 4
net: stmmac: xgmac: Fix XGMAC selftests
be2net: disable bh with spin_lock in be_process_mcc
net: cxgb3_main: Fix a resource leak in a error path in 'init_one()'
net: ethernet: sun4i-emac: Support phy-handle property for finding PHYs
net: bridge: move default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
...
TC mirred actions (redirect and mirred) can send to egress or ingress of a
device. Currently only egress is used for hw offload rules.
Modify the intermediate representation for hw offload to include mirred
actions that go to ingress. This gives drivers access to such rules and
can decide whether or not to offload them.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TC mirred actions can send to egress or ingress on a given netdev. Helpers
exist to detect actions that are mirred to egress. Extend the header file
to include helpers to detect ingress mirred actions.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
