Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
There is a handful of drivers which pass netdev->dev_addr as
the destination buffer to device_get_mac_address(). Add a helper
which takes a dev pointer instead, so it can call an appropriate
helper.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers pass in ETH_ALEN and the function itself
will return -EINVAL for any other address length.
Just assume it's ETH_ALEN like all other mac address
helpers (nvm, of, platform).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fwnode_get_mac_address() and device_get_mac_address()
return a pointer to the buffer that was passed to them
on success or NULL on failure. None of the callers
care about the actual value, only if it's NULL or not.
These semantics differ from of_get_mac_address() which
returns an int so to avoid confusion make the device
helpers return an errno.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
There are roughly 40 places where netdev->dev_addr is passed
as the destination to a of_get_mac_address() call. Add a helper
which takes a dev pointer instead, so it can call an appropriate
helper.
Note that of_get_mac_address() already assumes the address is
6 bytes long (ETH_ALEN) so use eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rob suggests to move of_net.c from under drivers/of/ somewhere
to the networking code.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mdiobus_modify_changed() helper to reflect the phylib and similar
equivalents. This will avoid this functionality being open-coded, as
has already happened in phylink, and it looks like other users will be
appearing soon.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add an extended state and sub-state to describe link issues related to
transceiver modules.
The 'ETHTOOL_LINK_EXT_SUBSTATE_MODULE_CMIS_NOT_READY' extended sub-state
tells user space that port is unable to gain a carrier because the CMIS
Module State Machine did not reach the ModuleReady (Fully Operational)
state. For example, if the module is stuck at ModuleLowPwr or
ModuleFault state. In case of the latter, user space can read the fault
reason from the module's EEPROM and potentially reset it.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a pair of new ethtool messages, 'ETHTOOL_MSG_MODULE_SET' and
'ETHTOOL_MSG_MODULE_GET', that can be used to control transceiver
modules parameters and retrieve their status.
The first parameter to control is the power mode of the module. It is
only relevant for paged memory modules, as flat memory modules always
operate in low power mode.
When a paged memory module is in low power mode, its power consumption
is reduced to the minimum, the management interface towards the host is
available and the data path is deactivated.
User space can choose to put modules that are not currently in use in
low power mode and transition them to high power mode before putting the
associated ports administratively up. This is useful for user space that
favors reduced power consumption and lower temperatures over reduced
link up times. In QSFP-DD modules the transition from low power mode to
high power mode can take a few seconds and this transition is only
expected to get longer with future / more complex modules.
User space can control the power mode of the module via the power mode
policy attribute ('ETHTOOL_A_MODULE_POWER_MODE_POLICY'). Possible
values:
* high: Module is always in high power mode.
* auto: Module is transitioned by the host to high power mode when the
first port using it is put administratively up and to low power mode
when the last port using it is put administratively down.
The operational power mode of the module is available to user space via
the 'ETHTOOL_A_MODULE_POWER_MODE' attribute. The attribute is not
reported to user space when a module is not plugged-in.
The user API is designed to be generic enough so that it could be used
for modules with different memory maps (e.g., SFF-8636, CMIS).
The only implementation of the device driver API in this series is for a
MAC driver (mlxsw) where the module is controlled by the device's
firmware, but it is designed to be generic enough so that it could also
be used by implementations where the module is controlled by the CPU.
CMIS testing
============
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
The module is not in low power mode, as it is not forced by hardware
(LowPwrAllowRequestHW is off) or by software (LowPwrRequestSW is off).
The power mode can be queried from the kernel. In case
LowPwrAllowRequestHW was on, the kernel would need to take into account
the state of the LowPwrRequestHW signal, which is not visible to user
space.
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp11 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp11 up
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp11 down
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
SFF-8636 testing
================
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7733 mW / -1.12 dBm
Transmit avg optical power (Channel 2) : 0.7649 mW / -1.16 dBm
Transmit avg optical power (Channel 3) : 0.7790 mW / -1.08 dBm
Transmit avg optical power (Channel 4) : 0.7837 mW / -1.06 dBm
Rcvr signal avg optical power(Channel 1) : 0.9302 mW / -0.31 dBm
Rcvr signal avg optical power(Channel 2) : 0.9079 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 3) : 0.8993 mW / -0.46 dBm
Rcvr signal avg optical power(Channel 4) : 0.8778 mW / -0.57 dBm
The module is not in low power mode, as it is not forced by hardware
(Power override is on) or by software (Power set is off).
The power mode can be queried from the kernel. In case Power override
was off, the kernel would need to take into account the state of the
LPMode signal, which is not visible to user space.
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp13 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp13 up
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7934 mW / -1.01 dBm
Transmit avg optical power (Channel 2) : 0.7859 mW / -1.05 dBm
Transmit avg optical power (Channel 3) : 0.7885 mW / -1.03 dBm
Transmit avg optical power (Channel 4) : 0.7985 mW / -0.98 dBm
Rcvr signal avg optical power(Channel 1) : 0.9325 mW / -0.30 dBm
Rcvr signal avg optical power(Channel 2) : 0.9034 mW / -0.44 dBm
Rcvr signal avg optical power(Channel 3) : 0.9086 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 4) : 0.8885 mW / -0.51 dBm
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp13 down
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for MediaTek MT7922 and MT7921
- Enable support for AOSP extention in Qualcomm WCN399x and Realtek
8822C/8852A.
- Add initial support for link quality and audio/codec offload.
- Rework of sockets sendmsg to avoid locking issues.
- Add vhci suspend/resume emulation.
====================
Link: https://lore.kernel.org/r/20211001230850.3635543-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netdev->dev_addr will become const soon. Make sure all
functions which pass it around mark appropriate args
as const.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_u64_to_mac() predates the common helper but doesn't
make the argument constant.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_mac_to_u64() predates and opencodes ether_addr_to_u64().
It doesn't make the argument constant so it'll be problematic
when dev->dev_addr becomes a const. Convert to the generic helper.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch the driver requires two IRQs to function properly,
one required IRQ for control and at least one required IRQ for IO.
This requirement can be relaxed to one as the driver now allows
sharing of IRQs, so control and IO EQs can share the same irq.
This is needed for high scale amount of VFs.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Control IRQ is the first IRQ vector. This complicates handling of
completion irqs as we need to offset them by one.
in the next patch, there are scenarios where completion and control EQs
will share the same irq. for example: functions with single IRQ. To ease
such scenarios, we shift control IRQ to the end of the irq array.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
On ingress VLAN push also assign value 0x7FE to reg_c1 tunnel id+opts
bits (tunnel id 0, which is not a valid tunnel id, and option 0x7FE which
was reserved by one of previous patches in the series). In following patch
the reg value is matched on egress miss to restore the packet to its
original state by removing the VLAN before passing it to the software data
path.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add a helper for setting 10Gigabit modes, so we have one central
place that sets all appropriate 10G modes for a driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update TCP silly-window-syndrome timeout, for the cases where
initiator's small TCP window size prevents FW from transmitting
packets on the connection. Timeout causes FW to retransmit
window probes if needed, preventing I/O stall if initiator ignores
first window probe.
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nikolay Assa <nassa@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qed_hsi.h has been updated to support new FW version 8.59.1.0 with
changes.
- Updates FW HSI (Hardware Software interface) structures.
- Addition/update in function declaration and defines as per HSI.
- Add generic infrastructure for FW error reporting as part of
common event queue handling.
- Move malicious VF error reporting to FW error reporting
infrastructure.
- Move consolidation queue initialization from FW context to ramrod
message.
qed_hsi.h header file changes lead to change in many files to ensure
compilation.
This patch also fixes the existing checkpatch warnings and few important
checks.
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The common_hsi.h has been updated for FW version 8.59.1.0 with below
changes.
- FW and Tools version.
- New structures related to search table, packet duplication.
- Structure for doorbell address for legacy mode without DEM.
- Enhanced union rdma_eqe_data for RoCE Suspend Event Data.
- New defines.
This patch also fixes the existing checkpatch warnings and few important
checks.
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing qed/qede/qedr/qedi/qedf code uses chip-specific naming in
structures, functions, variables and defines in FW HSI (Hardware
Software Interface).
The new FW version introduced a generic naming convention in HSI
in-which the same code will be used across different versions
for simpler maintainability. It also eases in providing support for
new features.
With this patch every "_e4" or "e4_" prefix or suffix is not needed
anymore and it will be removed.
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes all the qed and qede kernel-doc warnings
according to the guidelines that are described in
Documentation/doc-guide/kernel-doc.rst.
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the ip6ip6 encapsulation by providing three encap
modes: inline, encap and auto.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch anticipates the support for the IOAM insertion inside in-transit
packets, by making a difference between input and output in order to determine
the right value for its hop-limit (inherited from the IPv6 hop-limit).
Input case: happens before ip6_forward, the IPv6 hop-limit is not decremented
yet -> decrement the IOAM hop-limit to reflect the new hop inside the trace.
Output case: happens after ip6_forward, the IPv6 hop-limit has already been
decremented -> keep the same value for the IOAM hop-limit.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert Ethernet from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VLAN TCI contains more than the VLAN ID, it also has the VLAN PCP
and Drop Eligibility Indicator.
If the ocelot driver is going to write the VLAN header inside the DSA
tag, it could just as well write the entire TCI.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ocelot driver does support the 'vlan modify' action, but
in the ingress chain, and it is offloaded to VCAP IS1. This action
changes the classified VLAN before the packet enters the bridging
service, and the bridging works with the classified VLAN modified by
VCAP IS1.
That is good for some use cases, but there are others where the VLAN
must be modified at the stage of the egress port, after the packet has
exited the bridging service. One example is simulating IEEE 802.1CB
active stream identification filters ("active" means that not only the
rule matches on a packet flow, but it is also able to change some
headers). For example, a stream is replicated on two egress ports, but
they must have different VLAN IDs on egress ports A and B.
This seems like a task for the VCAP ES0, but that currently only
supports pushing the ES0 tag A, which is specified in the rule. Pushing
another VLAN header is not what we want, but rather overwriting the
existing one.
It looks like when we push the ES0 tag A, it is actually possible to not
only take the ES0 tag A's value from the rule itself (VID_A_VAL), but
derive it from the following formula:
ES0_TAG_A = Classified VID + VID_A_VAL
Otherwise said, ES0_TAG_A can be used to increment with a given value
the VLAN ID that the packet was already classified to, and the packet
will have this value as an outer VLAN tag. This new VLAN ID value then
gets stripped on egress (or not) according to the value of the native
VLAN from the bridging service.
While the hardware will happily increment the classified VLAN ID for all
packets that match the ES0 rule, in practice this would be rather
insane, so we only allow this kind of ES0 action if the ES0 filter
contains a VLAN ID too, so as to restrict the matching on a known
classified VLAN. If we program VID_A_VAL with the delta between the
desired final VLAN (ES0_TAG_A) and the classified VLAN, we obtain the
desired behavior.
It doesn't look like it is possible with the tc-vlan action to modify
the VLAN ID but not the PCP. In hardware it is possible to leave the PCP
to the classified value, but we unconditionally program it to overwrite
it with the PCP value from the rule.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
bpf-next 2021-10-02
We've added 85 non-merge commits during the last 15 day(s) which contain
a total of 132 files changed, 13779 insertions(+), 6724 deletions(-).
The main changes are:
1) Massive update on test_bpf.ko coverage for JITs as preparatory work for
an upcoming MIPS eBPF JIT, from Johan Almbladh.
2) Add a batched interface for RX buffer allocation in AF_XDP buffer pool,
with driver support for i40e and ice from Magnus Karlsson.
3) Add legacy uprobe support to libbpf to complement recently merged legacy
kprobe support, from Andrii Nakryiko.
4) Add bpf_trace_vprintk() as variadic printk helper, from Dave Marchevsky.
5) Support saving the register state in verifier when spilling <8byte bounded
scalar to the stack, from Martin Lau.
6) Add libbpf opt-in for stricter BPF program section name handling as part
of libbpf 1.0 effort, from Andrii Nakryiko.
7) Add a document to help clarifying BPF licensing, from Alexei Starovoitov.
8) Fix skel_internal.h to propagate errno if the loader indicates an internal
error, from Kumar Kartikeya Dwivedi.
9) Fix build warnings with -Wcast-function-type so that the option can later
be enabled by default for the kernel, from Kees Cook.
10) Fix libbpf to ignore STT_SECTION symbols in legacy map definitions as it
otherwise errors out when encountering them, from Toke Høiland-Jørgensen.
11) Teach libbpf to recognize specialized maps (such as for perf RB) and
internally remove BTF type IDs when creating them, from Hengqi Chen.
12) Various fixes and improvements to BPF selftests.
====================
Link: https://lore.kernel.org/r/20211002001327.15169-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
prevent_wake logic is backward since what it is really checking is
if the device may wakeup the system or not, not that it will prevent
the to be awaken.
Also looking on how other subsystems have the entry as power/wakeup
this also renames the force_prevent_wake to force_wakeup in vhci driver.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Each region has an independently configurable number of maximum
snapshots. This information is not reported to userspace, making it not
very discoverable. Fix this by adding a new
DEVLINK_ATTR_REGION_MAX_SNAPSHOST attribute which is used to report this
maximum.
Ex:
$devlink region
pci/0000:af:00.0/nvm-flash: size 10485760 snapshot [] max 1
pci/0000:af:00.0/device-caps: size 4096 snapshot [] max 10
pci/0000:af:00.1/nvm-flash: size 10485760 snapshot [] max 1
pci/0000:af:00.1/device-caps: size 4096 snapshot [] max 10
This information enables users to understand why a new region command
may fail due to having too many existing snapshots.
Reported-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from mac80211, netfilter and bpf.
Current release - regressions:
- bpf, cgroup: assign cgroup in cgroup_sk_alloc when called from
interrupt
- mdio: revert mechanical patches which broke handling of optional
resources
- dev_addr_list: prevent address duplication
Previous releases - regressions:
- sctp: break out if skb_header_pointer returns NULL in sctp_rcv_ootb
(NULL deref)
- Revert "mac80211: do not use low data rates for data frames with no
ack flag", fixing broadcast transmissions
- mac80211: fix use-after-free in CCMP/GCMP RX
- netfilter: include zone id in tuple hash again, minimize collisions
- netfilter: nf_tables: unlink table before deleting it (race -> UAF)
- netfilter: log: work around missing softdep backend module
- mptcp: don't return sockets in foreign netns
- sched: flower: protect fl_walk() with rcu (race -> UAF)
- ixgbe: fix NULL pointer dereference in ixgbe_xdp_setup
- smsc95xx: fix stalled rx after link change
- enetc: fix the incorrect clearing of IF_MODE bits
- ipv4: fix rtnexthop len when RTA_FLOW is present
- dsa: mv88e6xxx: 6161: use correct MAX MTU config method for this
SKU
- e100: fix length calculation & buffer overrun in ethtool::get_regs
Previous releases - always broken:
- mac80211: fix using stale frag_tail skb pointer in A-MSDU tx
- mac80211: drop frames from invalid MAC address in ad-hoc mode
- af_unix: fix races in sk_peer_pid and sk_peer_cred accesses (race
-> UAF)
- bpf, x86: Fix bpf mapping of atomic fetch implementation
- bpf: handle return value of BPF_PROG_TYPE_STRUCT_OPS prog
- netfilter: ip6_tables: zero-initialize fragment offset
- mhi: fix error path in mhi_net_newlink
- af_unix: return errno instead of NULL in unix_create1() when over
the fs.file-max limit
Misc:
- bpf: exempt CAP_BPF from checks against bpf_jit_limit
- netfilter: conntrack: make max chain length random, prevent
guessing buckets by attackers
- netfilter: nf_nat_masquerade: make async masq_inet6_event handling
generic, defer conntrack walk to work queue (prevent hogging RTNL
lock)"
* tag 'net-5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (77 commits)
af_unix: fix races in sk_peer_pid and sk_peer_cred accesses
net: stmmac: fix EEE init issue when paired with EEE capable PHYs
net: dev_addr_list: handle first address in __hw_addr_add_ex
net: sched: flower: protect fl_walk() with rcu
net: introduce and use lock_sock_fast_nested()
net: phy: bcm7xxx: Fixed indirect MMD operations
net: hns3: disable firmware compatible features when uninstall PF
net: hns3: fix always enable rx vlan filter problem after selftest
net: hns3: PF enable promisc for VF when mac table is overflow
net: hns3: fix show wrong state when add existing uc mac address
net: hns3: fix mixed flag HCLGE_FLAG_MQPRIO_ENABLE and HCLGE_FLAG_DCB_ENABLE
net: hns3: don't rollback when destroy mqprio fail
net: hns3: remove tc enable checking
net: hns3: do not allow call hns3_nic_net_open repeatedly
ixgbe: Fix NULL pointer dereference in ixgbe_xdp_setup
net: bridge: mcast: Associate the seqcount with its protecting lock.
net: mdio-ipq4019: Fix the error for an optional regs resource
net: hns3: fix hclge_dbg_dump_tm_pg() stack usage
net: mdio: mscc-miim: Fix the mdio controller
af_unix: Return errno instead of NULL in unix_create1().
...
Jann Horn reported that SO_PEERCRED and SO_PEERGROUPS implementations
are racy, as af_unix can concurrently change sk_peer_pid and sk_peer_cred.
In order to fix this issue, this patch adds a new spinlock that needs
to be used whenever these fields are read or written.
Jann also pointed out that l2cap_sock_get_peer_pid_cb() is currently
reading sk->sk_peer_pid which makes no sense, as this field
is only possibly set by AF_UNIX sockets.
We will have to clean this in a separate patch.
This could be done by reverting b48596d1dc "Bluetooth: L2CAP: Add get_peer_pid callback"
or implementing what was truly expected.
Fixes: 109f6e39fa ("af_unix: Allow SO_PEERCRED to work across namespaces.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jann Horn <jannh@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This trivial function is called ~90,000 times on 256 cpus hosts,
when reading /proc/net/netstat. And this number keeps inflating.
Inlining it saves many cycles.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user sets SO_RESERVE_MEM socket option, in order to utilize the
reserved memory when in memory pressure state, we adjust rcv_ssthresh
according to the available reserved memory for the socket, instead of
using 4 * advmss always.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If user sets SO_RESERVE_MEM socket option, in order to fully utilize the
reserved memory in memory pressure state on the tx path, we modify the
logic in sk_stream_moderate_sndbuf() to set sk_sndbuf according to
available reserved memory, instead of MIN_SOCK_SNDBUF, and adjust it
when new data is acked.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This socket option provides a mechanism for users to reserve a certain
amount of memory for the socket to use. When this option is set, kernel
charges the user specified amount of memory to memcg, as well as
sk_forward_alloc. This amount of memory is not reclaimable and is
available in sk_forward_alloc for this socket.
With this socket option set, the networking stack spends less cycles
doing forward alloc and reclaim, which should lead to better system
performance, with the cost of an amount of pre-allocated and
unreclaimable memory, even under memory pressure.
Note:
This socket option is only available when memory cgroup is enabled and we
require this reserved memory to be charged to the user's memcg. We hope
this could avoid mis-behaving users to abused this feature to reserve a
large amount on certain sockets and cause unfairness for others.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull sound fixes from Takashi Iwai:
"This became a slightly large collection of changes, partly because
I've been off in the last weeks. Most of changes are small and
scattered while a bit big change is found in HD-audio Realtek codec
driver; it's a very device-specific fix that has been long wanted, so
I decided to pick up although it's in the middle RC.
Some highlights:
- A new guard ioctl for ALSA rawmidi API to avoid the misuse of the
new timestamp framing mode; it's for a regression fix
- HD-audio: a revert of the 5.15 change that might work badly, new
quirks for Lenovo Legion & co, a follow-up fix for CS8409
- ASoC: lots of SOF-related fixes, fsl component fixes, corrections
of mediatek drivers
- USB-audio: fix for the PM resume
- FireWire: oxfw and motu fixes"
* tag 'sound-5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (25 commits)
ALSA: pcsp: Make hrtimer forwarding more robust
ALSA: rawmidi: introduce SNDRV_RAWMIDI_IOCTL_USER_PVERSION
ALSA: firewire-motu: fix truncated bytes in message tracepoints
ASoC: SOF: trace: Omit error print when waking up trace sleepers
ASoC: mediatek: mt8195: remove wrong fixup assignment on HDMITX
ASoC: SOF: loader: Re-phrase the missing firmware error to avoid duplication
ASoC: SOF: loader: release_firmware() on load failure to avoid batching
ALSA: hda/cs8409: Setup Dolphin Headset Mic as Phantom Jack
ALSA: pcxhr: "fix" PCXHR_REG_TO_PORT definition
ASoC: SOF: imx: imx8m: Bar index is only valid for IRAM and SRAM types
ASoC: SOF: imx: imx8: Bar index is only valid for IRAM and SRAM types
ASoC: SOF: Fix DSP oops stack dump output contents
ALSA: hda/realtek: Quirks to enable speaker output for Lenovo Legion 7i 15IMHG05, Yoga 7i 14ITL5/15ITL5, and 13s Gen2 laptops.
ALSA: usb-audio: Unify mixer resume and reset_resume procedure
Revert "ALSA: hda: Drop workaround for a hang at shutdown again"
ALSA: oxfw: fix transmission method for Loud models based on OXFW971
ASoC: mediatek: common: handle NULL case in suspend/resume function
ASoC: fsl_xcvr: register platform component before registering cpu dai
ASoC: fsl_spdif: register platform component before registering cpu dai
ASoC: fsl_micfil: register platform component before registering cpu dai
...
The tag allocation, release and bind events are somewhat opaque outside
the kernel; this change adds a few tracepoints to assist in
instrumentation and debugging.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a MCTP (local-eid,remote-eid,tag) tuple is allocated to a
socket on send, and only expires when the socket is closed.
This change introduces a tag timeout, freeing the tuple after a fixed
expiry - currently six seconds. This is greater than (but close to) the
max response timeout in upper-layer bindings.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we tie the struct mctp_dev lifetime to the underlying struct
net_device, and hold/put that device as a proxy for a separate mctp_dev
refcount. This works because we're not holding any references to the
mctp_dev that are different from the netdev lifetime.
In a future change we'll break that assumption though, as we'll need to
hold mctp_dev references in a workqueue, which might live past the
netdev unregister notification.
In order to support that, this change introduces a refcount on the
mctp_dev, currently taken by the net_device->mctp_ptr reference, and
released on netdev unregister events. We can then use this for future
references that might outlast the net device.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will want to invalidate sk_keys in a future change, which will
require a boolean flag to mark invalidated items in the socket & net
namespace lists. We'll also need to take a reference to keys, held over
non-atomic contexts, so we need a refcount on keys also.
This change adds a validity flag (currently always true) and refcount to
struct mctp_sk_key. With a refcount on the keys, using RCU no longer
makes much sense; we have exact indications on the lifetime of keys. So,
we also change the RCU list traversal to a locked implementation.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN8804 PHY has same features as that of LAN8814 PHY except that it
doesn't support 1588, SyncE or Q-USGMII.
This PHY is found inside the LAN966X switches.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver uses software CQ head pointer to poll on CQE
header in memory to determine if CQE is valid. Software needs
to make sure, that the reads of the CQE do not get re-ordered
so much that it ends up with an inconsistent view of the CQE.
To ensure that DMB barrier after read to first CQE cacheline
and before reading of the rest of the CQE is needed.
But having barrier for every CQE read will impact the performance,
instead use hardware CQ head and tail pointers to find the
valid number of CQEs.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
