Pull spi updates from Mark Brown:
"One new core feature here, a small collection of new drivers and a
bunch of small improvements in existing drivers:
- A new CS_WORD flag for transfers where the chip select is toggled
at every word, with both a generic implementation and the ability
for controllers to do this automatically (including a DaVinci one).
- New drivers for Mediatek MT2712, Qualcomm GENI and QSPI, Spreadtrum
SPI and ST STM32 QSPI plus new IDs for several existing ones"
* tag 'spi-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (86 commits)
spi: lpspi: add imx8qxp compatible string
spi: Allow building SPI_BCM63XX_HSSPI on ARM-based SoCs
spi: omap2-mcspi: Add slave mode support
spi: omap2-mcspi: Set FIFO DMA trigger level to word length
spi: omap2-mcspi: Switch to readl_poll_timeout()
spi: spi-mem: add stm32 qspi controller
dt-bindings: spi: add stm32 qspi controller
spi: sh-msiof: document R8A779{7|8}0 bindings
spi: pic32-sqi: don't pass GFP_DMA32 to dma_alloc_coherent
MAINTAINERS: Add entry for Broadcom SPI controller
spi: sh-msiof: fix deferred probing
spi: imx: use PIO mode if size is small
spi: imx: correct wml as the last sg length
spi: imx: move wml setting to later than setup_transfer
PCI: Provide pci_match_id() with CONFIG_PCI=n
spi: Make GPIO CSs honour the SPI_NO_CS flag
spi/spi-pxa2xx: add PXA2xx SSP SPI Controller
spi: pxa2xx: Add devicetree support
spi: pxa2xx: Use an enum for type
spi: spi-geni-qcom: Add SPI driver support for GENI based QUP
...
Pull regmap updates from Mark Brown:
"A small update with a couple of new APIs that are useful for some
small sets of devices:
- Split up the single_rw flagging to map read and write separately as
some devices support bulk operations for only read or only write.
- Add a write version of the noinc API.
- Clean up the code for LOG_DEVICE a bit"
* tag 'regmap-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: use less #ifdef for LOG_DEVICE
regmap: Add regmap_noinc_write API
regmap: split up regmap_config.use_single_rw
regmap: fix comment for regmap.use_single_write
Pull mtd updates from Boris Brezillon:
"SPI NOR core changes:
- Support non-uniform erase size
- Support controllers with limited TX fifo size
Driver changes:
- m25p80: Re-issue a WREN command after each write access
- cadence: Pass a proper dir value to dma_[un]map_single()
- fsl-qspi: Check fsl_qspi_get_seqid() return val make sure 4B
addressing opcodes are properly handled
- intel-spi: Add a new PCI entry for Ice Lake
Raw NAND core changes:
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID
byte.
MTD changes:
- physmap cleanups/fixe
- gpio-addr-flash cleanups/fixes"
* tag 'mtd/for-4.20' of git://git.infradead.org/linux-mtd: (93 commits)
jffs2: free jffs2_sb_info through jffs2_kill_sb()
mtd: spi-nor: fsl-quadspi: fix read error for flash size larger than 16MB
mtd: spi-nor: intel-spi: Add support for Intel Ice Lake SPI serial flash
mtd: maps: gpio-addr-flash: Convert to gpiod
mtd: maps: gpio-addr-flash: Replace array with an integer
mtd: maps: gpio-addr-flash: Use order instead of size
mtd: spi-nor: fsl-quadspi: Don't let -EINVAL on the bus
mtd: devices: m25p80: Make sure WRITE_EN is issued before each write
mtd: spi-nor: Support controllers with limited TX FIFO size
mtd: spi-nor: cadence-quadspi: Use proper enum for dma_[un]map_single
mtd: spi-nor: parse SFDP Sector Map Parameter Table
mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories
mtd: rawnand: marvell: fix the IRQ handler complete() condition
mtd: rawnand: denali: set SPARE_AREA_SKIP_BYTES register to 8 if unset
mtd: rawnand: r852: fix spelling mistake "card_registred" -> "card_registered"
mtd: rawnand: toshiba: Pass a single nand_chip object to the status helper
mtd: maps: gpio-addr-flash: Use devm_* functions
mtd: maps: gpio-addr-flash: Fix ioremapped size
mtd: maps: gpio-addr-flash: Replace custom printk
mtd: physmap_of: Release resources on error
...
Pull hwmon updates from Guenter Roeck:
- Add support for trace events to hwmon core
- Add support for NCT6797D, NCT6798D, MAX31725/6, LTM4686
- Support all AMD Family 15h Model 6xh and Model 7xh processors in
k10temp driver
- Convert ina3221 driver to _info API
- Fixes, cleanups, and improvements in various drivers
* tag 'hwmon-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (46 commits)
hwmon: (pmbus) Fix page count auto-detection.
hwmon: (pmbus) remove redundant 'default n' from Kconfig
hwmon: (core) Add trace events to _attr_show/store functions
hwmon: (ina3221) Use _info API to register hwmon device
hwmon: (npcm-750-pwm-fan) Change initial pwm target to 255
hwmon: (ina3221) Validate shunt resistor value from DT
hwmon: (tmp421) make const array 'names' static
hwmon: (core) Add hwmon_in_enable attribute
hwmon: (ina3221) mark PM functions as __maybe_unused
hwmon: (ina3221) Read channel input source info from DT
dt-bindings: hwmon: Add ina3221 documentation
hwmon: (ina3221) Add suspend and resume functions
hwmon: (ina3221) Fix INA3221_CONFIG_MODE macros
hwmon: (ina3221) Add INA3221_CONFIG to volatile_table
MAINTAINERS: Update PMBUS maintainer entry
hwmon: (pwm-fan) Set fan speed to 0 on suspend
hwmon: (pwm-fan) Silence error on probe deferral
hwmon: (scpi-hwmon) remove redundant continue
hwmon: (nct6775) Add support for NCT6798D
hwmon: (nct6775) Add support for NCT6797D
...
Pull dma mapping updates from Christoph Hellwig:
"First batch of dma-mapping changes for 4.20.
There will be a second PR as some big changes were only applied just
before the end of the merge window, and I want to give them a few more
days in linux-next.
Summary:
- mostly more consolidation of the direct mapping code, including
converting over hexagon, and merging the coherent and non-coherent
code into a single dma_map_ops instance (me)
- cleanups for the dma_configure/dma_unconfigure callchains (me)
- better handling of dma_masks in odd setups (me, Alexander Duyck)
- better debugging of passing vmalloc address to the DMA API (Stephen
Boyd)
- CMA command line parsing fix (He Zhe)"
* tag 'dma-mapping-4.20' of git://git.infradead.org/users/hch/dma-mapping: (27 commits)
dma-direct: respect DMA_ATTR_NO_WARN
dma-mapping: translate __GFP_NOFAIL to DMA_ATTR_NO_WARN
dma-direct: document the zone selection logic
dma-debug: Check for drivers mapping invalid addresses in dma_map_single()
dma-direct: fix return value of dma_direct_supported
dma-mapping: move dma_default_get_required_mask under ifdef
dma-direct: always allow dma mask <= physiscal memory size
dma-direct: implement complete bus_dma_mask handling
dma-direct: refine dma_direct_alloc zone selection
dma-direct: add an explicit dma_direct_get_required_mask
dma-mapping: make the get_required_mask method available unconditionally
unicore32: remove swiotlb support
Revert "dma-mapping: clear dev->dma_ops in arch_teardown_dma_ops"
dma-mapping: support non-coherent devices in dma_common_get_sgtable
dma-mapping: consolidate the dma mmap implementations
dma-mapping: merge direct and noncoherent ops
dma-mapping: move the dma_coherent flag to struct device
MIPS: don't select DMA_MAYBE_COHERENT from DMA_PERDEV_COHERENT
dma-mapping: add the missing ARCH_HAS_SYNC_DMA_FOR_CPU_ALL declaration
dma-mapping: fix panic caused by passing empty cma command line argument
...
Pull block layer updates from Jens Axboe:
"This is the main pull request for block changes for 4.20. This
contains:
- Series enabling runtime PM for blk-mq (Bart).
- Two pull requests from Christoph for NVMe, with items such as;
- Better AEN tracking
- Multipath improvements
- RDMA fixes
- Rework of FC for target removal
- Fixes for issues identified by static checkers
- Fabric cleanups, as prep for TCP transport
- Various cleanups and bug fixes
- Block merging cleanups (Christoph)
- Conversion of drivers to generic DMA mapping API (Christoph)
- Series fixing ref count issues with blkcg (Dennis)
- Series improving BFQ heuristics (Paolo, et al)
- Series improving heuristics for the Kyber IO scheduler (Omar)
- Removal of dangerous bio_rewind_iter() API (Ming)
- Apply single queue IPI redirection logic to blk-mq (Ming)
- Set of fixes and improvements for bcache (Coly et al)
- Series closing a hotplug race with sysfs group attributes (Hannes)
- Set of patches for lightnvm:
- pblk trace support (Hans)
- SPDX license header update (Javier)
- Tons of refactoring patches to cleanly abstract the 1.2 and 2.0
specs behind a common core interface. (Javier, Matias)
- Enable pblk to use a common interface to retrieve chunk metadata
(Matias)
- Bug fixes (Various)
- Set of fixes and updates to the blk IO latency target (Josef)
- blk-mq queue number updates fixes (Jianchao)
- Convert a bunch of drivers from the old legacy IO interface to
blk-mq. This will conclude with the removal of the legacy IO
interface itself in 4.21, with the rest of the drivers (me, Omar)
- Removal of the DAC960 driver. The SCSI tree will introduce two
replacement drivers for this (Hannes)"
* tag 'for-4.20/block-20181021' of git://git.kernel.dk/linux-block: (204 commits)
block: setup bounce bio_sets properly
blkcg: reassociate bios when make_request() is called recursively
blkcg: fix edge case for blk_get_rl() under memory pressure
nvme-fabrics: move controller options matching to fabrics
nvme-rdma: always have a valid trsvcid
mtip32xx: fully switch to the generic DMA API
rsxx: switch to the generic DMA API
umem: switch to the generic DMA API
sx8: switch to the generic DMA API
sx8: remove dead IF_64BIT_DMA_IS_POSSIBLE code
skd: switch to the generic DMA API
ubd: remove use of blk_rq_map_sg
nvme-pci: remove duplicate check
drivers/block: Remove DAC960 driver
nvme-pci: fix hot removal during error handling
nvmet-fcloop: suppress a compiler warning
nvme-core: make implicit seed truncation explicit
nvmet-fc: fix kernel-doc headers
nvme-fc: rework the request initialization code
nvme-fc: introduce struct nvme_fcp_op_w_sgl
...
Pull arm64 updates from Catalin Marinas:
"Apart from some new arm64 features and clean-ups, this also contains
the core mmu_gather changes for tracking the levels of the page table
being cleared and a minor update to the generic
compat_sys_sigaltstack() introducing COMPAT_SIGMINSKSZ.
Summary:
- Core mmu_gather changes which allow tracking the levels of
page-table being cleared together with the arm64 low-level flushing
routines
- Support for the new ARMv8.5 PSTATE.SSBS bit which can be used to
mitigate Spectre-v4 dynamically without trapping to EL3 firmware
- Introduce COMPAT_SIGMINSTKSZ for use in compat_sys_sigaltstack
- Optimise emulation of MRS instructions to ID_* registers on ARMv8.4
- Support for Common Not Private (CnP) translations allowing threads
of the same CPU to share the TLB entries
- Accelerated crc32 routines
- Move swapper_pg_dir to the rodata section
- Trap WFI instruction executed in user space
- ARM erratum 1188874 workaround (arch_timer)
- Miscellaneous fixes and clean-ups"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (78 commits)
arm64: KVM: Guests can skip __install_bp_hardening_cb()s HYP work
arm64: cpufeature: Trap CTR_EL0 access only where it is necessary
arm64: cpufeature: Fix handling of CTR_EL0.IDC field
arm64: cpufeature: ctr: Fix cpu capability check for late CPUs
Documentation/arm64: HugeTLB page implementation
arm64: mm: Use __pa_symbol() for set_swapper_pgd()
arm64: Add silicon-errata.txt entry for ARM erratum 1188873
Revert "arm64: uaccess: implement unsafe accessors"
arm64: mm: Drop the unused cpu parameter
MAINTAINERS: fix bad sdei paths
arm64: mm: Use #ifdef for the __PAGETABLE_P?D_FOLDED defines
arm64: Fix typo in a comment in arch/arm64/mm/kasan_init.c
arm64: xen: Use existing helper to check interrupt status
arm64: Use daifflag_restore after bp_hardening
arm64: daifflags: Use irqflags functions for daifflags
arm64: arch_timer: avoid unused function warning
arm64: Trap WFI executed in userspace
arm64: docs: Document SSBS HWCAP
arm64: docs: Fix typos in ELF hwcaps
arm64/kprobes: remove an extra semicolon in arch_prepare_kprobe
...
When submitting a bio, multiple recursive calls to make_request() may
occur. This causes the initial associate done in blkcg_bio_issue_check()
to be incorrect and reference the prior request_queue. This introduces
a helper to do reassociation when make_request() is recursively called.
Fixes: a7b39b4e96 ("blkcg: always associate a bio with a blkg")
Reported-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Tested-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It is possible for blkg creation to fail when in blk_get_rl(). In this
situation, the fallback logic returns the nearest created blkg. There is
however special handling for the request_list for the root blkcg. This
fixes the missing edge case from the earlier series changing
blk_get_rl().
Fixes: e2b0989954 ("blkcg: cleanup and make blk_get_rl use blkg_lookup_create")
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Dave writes:
"drm fixes for 4.19 final (part 2)
Looked like two stragglers snuck in, one very urgent the pageflipping
was missing a reference that could result in a GPF on non-i915
drivers, the other is an overflow in the sun4i dotclock calcs
resulting in a mode not getting set."
* tag 'drm-fixes-2018-10-20-1' of git://anongit.freedesktop.org/drm/drm:
drm/sun4i: Fix an ulong overflow in the dotclock driver
drm: Get ref on CRTC commit object when waiting for flip_done
The regmap API had a noinc_read function added for instances where devices
supported returning data from an internal FIFO in a single read.
This commit adds the noinc_write variant to allow writing to a non
incrementing register, this is used in devices such as the sx1301 for
loading firmware.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
NAND core changes:
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID byte.
David writes:
"Networking
1) Fix gro_cells leak in xfrm layer, from Li RongQing.
2) BPF selftests change RLIMIT_MEMLOCK blindly, don't do that. From
Eric Dumazet.
3) AF_XDP calls synchronize_net() under RCU lock, fix from Björn
Töpel.
4) Out of bounds packet access in _decode_session6(), from Alexei
Starovoitov.
5) Several ethtool bugs, where we copy a struct into the kernel twice
and our validations of the values in the first copy can be
invalidated by the second copy due to asynchronous updates to the
memory by the user. From Wenwen Wang.
6) Missing netlink attribute validation in cls_api, from Davide
Caratti.
7) LLC SAP sockets neet to be SOCK_RCU FREE, from Cong Wang.
8) rxrpc operates on wrong kvec, from Yue Haibing.
9) A regression was introduced by the disassosciation of route
neighbour references in rt6_probe(), causing probe for
neighbourless routes to not be properly rate limited. Fix from
Sabrina Dubroca.
10) Unsafe RCU locking in tipc, from Tung Nguyen.
11) Use after free in inet6_mc_check(), from Eric Dumazet.
12) PMTU from icmp packets should update the SCTP transport pathmtu,
from Xin Long.
13) Missing peer put on error in rxrpc, from David Howells.
14) Fix pedit in nfp driver, from Pieter Jansen van Vuuren.
15) Fix overflowing shift statement in qla3xxx driver, from Nathan
Chancellor.
16) Fix Spectre v1 in ptp code, from Gustavo A. R. Silva.
17) udp6_unicast_rcv_skb() interprets udpv6_queue_rcv_skb() return
value in an inverted manner, fix from Paolo Abeni.
18) Fix missed unresolved entries in ipmr dumps, from Nikolay
Aleksandrov.
19) Fix NAPI handling under high load, we can completely miss events
when NAPI has to loop more than one time in a cycle. From Heiner
Kallweit."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (49 commits)
ip6_tunnel: Fix encapsulation layout
tipc: fix info leak from kernel tipc_event
net: socket: fix a missing-check bug
net: sched: Fix for duplicate class dump
r8169: fix NAPI handling under high load
net: ipmr: fix unresolved entry dumps
net: mscc: ocelot: Fix comment in ocelot_vlant_wait_for_completion()
sctp: fix the data size calculation in sctp_data_size
virtio_net: avoid using netif_tx_disable() for serializing tx routine
udp6: fix encap return code for resubmitting
mlxsw: core: Fix use-after-free when flashing firmware during init
sctp: not free the new asoc when sctp_wait_for_connect returns err
sctp: fix race on sctp_id2asoc
r8169: re-enable MSI-X on RTL8168g
net: bpfilter: use get_pid_task instead of pid_task
ptp: fix Spectre v1 vulnerability
net: qla3xxx: Remove overflowing shift statement
geneve, vxlan: Don't set exceptions if skb->len < mtu
geneve, vxlan: Don't check skb_dst() twice
sctp: get pr_assoc and pr_stream all status with SCTP_PR_SCTP_ALL instead
...
Dave writes:
"drm fixes for 4.19 final
Just a last set of misc core fixes for final.
4 fixes, one use after free, one fb integration fix, one EDID fix,
and one laptop panel quirk,"
* tag 'drm-fixes-2018-10-19' of git://anongit.freedesktop.org/drm/drm:
drm/edid: VSDB yCBCr420 Deep Color mode bit definitions
drm: fix use of freed memory in drm_mode_setcrtc
drm: fb-helper: Reject all pixel format changing requests
drm/edid: Add 6 bpc quirk for BOE panel in HP Pavilion 15-n233sl
This fixes a general protection fault, caused by accessing the contents
of a flip_done completion object that has already been freed. It occurs
due to the preemption of a non-blocking commit worker thread W by
another commit thread X. X continues to clear its atomic state at the
end, destroying the CRTC commit object that W still needs. Switching
back to W and accessing the commit objects then leads to bad results.
Worker W becomes preemptable when waiting for flip_done to complete. At
this point, a frequently occurring commit thread X can take over. Here's
an example where W is a worker thread that flips on both CRTCs, and X
does a legacy cursor update on both CRTCs:
...
1. W does flip work
2. W runs commit_hw_done()
3. W waits for flip_done on CRTC 1
4. > flip_done for CRTC 1 completes
5. W finishes waiting for CRTC 1
6. W waits for flip_done on CRTC 2
7. > Preempted by X
8. > flip_done for CRTC 2 completes
9. X atomic_check: hw_done and flip_done are complete on all CRTCs
10. X updates cursor on both CRTCs
11. X destroys atomic state
12. X done
13. > Switch back to W
14. W waits for flip_done on CRTC 2
15. W raises general protection fault
The error looks like so:
general protection fault: 0000 [#1] PREEMPT SMP PTI
**snip**
Call Trace:
lock_acquire+0xa2/0x1b0
_raw_spin_lock_irq+0x39/0x70
wait_for_completion_timeout+0x31/0x130
drm_atomic_helper_wait_for_flip_done+0x64/0x90 [drm_kms_helper]
amdgpu_dm_atomic_commit_tail+0xcae/0xdd0 [amdgpu]
commit_tail+0x3d/0x70 [drm_kms_helper]
process_one_work+0x212/0x650
worker_thread+0x49/0x420
kthread+0xfb/0x130
ret_from_fork+0x3a/0x50
Modules linked in: x86_pkg_temp_thermal amdgpu(O) chash(O)
gpu_sched(O) drm_kms_helper(O) syscopyarea sysfillrect sysimgblt
fb_sys_fops ttm(O) drm(O)
Note that i915 has this issue masked, since hw_done is signaled after
waiting for flip_done. Doing so will block the cursor update from
happening until hw_done is signaled, preventing the cursor commit from
destroying the state.
v2: The reference on the commit object needs to be obtained before
hw_done() is signaled, since that's the point where another commit
is allowed to modify the state. Assuming that the
new_crtc_state->commit object still exists within flip_done() is
incorrect.
Fix by getting a reference in setup_commit(), and releasing it
during default_clear().
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539611200-6184-1-git-send-email-sunpeng.li@amd.com
Jann Horn points out that our TLB flushing was subtly wrong for the
mremap() case. What makes mremap() special is that we don't follow the
usual "add page to list of pages to be freed, then flush tlb, and then
free pages". No, mremap() obviously just _moves_ the page from one page
table location to another.
That matters, because mremap() thus doesn't directly control the
lifetime of the moved page with a freelist: instead, the lifetime of the
page is controlled by the page table locking, that serializes access to
the entry.
As a result, we need to flush the TLB not just before releasing the lock
for the source location (to avoid any concurrent accesses to the entry),
but also before we release the destination page table lock (to avoid the
TLB being flushed after somebody else has already done something to that
page).
This also makes the whole "need_flush" logic unnecessary, since we now
always end up flushing the TLB for every valid entry.
Reported-and-tested-by: Jann Horn <jannh@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sctp data size should be calculated by subtracting data chunk header's
length from chunk_hdr->length, not just data header.
Fixes: 668c9beb90 ("sctp: implement assign_number for sctp_stream_interleave")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steven writes:
"tracing: Two fixes for 4.19
This fixes two bugs:
- Fix size mismatch of tracepoint array
- Have preemptirq test module use same clock source of the selftest"
* tag 'trace-v4.19-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Use trace_clock_local() for looping in preemptirq_delay_test.c
tracepoint: Fix tracepoint array element size mismatch
We shouldn't abuse exceptions: if the destination MTU is already higher
than what we're transmitting, no exception should be created.
Fixes: 52a589d51f ("geneve: update skb dst pmtu on tx path")
Fixes: a93bf0ff44 ("vxlan: update skb dst pmtu on tx path")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 46e0c9be20 ("kernel: tracepoints: add support for relative
references") changes the layout of the __tracepoint_ptrs section on
architectures supporting relative references. However, it does so
without turning struct tracepoint * const into const int elsewhere in
the tracepoint code, which has the following side-effect:
Setting mod->num_tracepoints is done in by module.c:
mod->tracepoints_ptrs = section_objs(info, "__tracepoints_ptrs",
sizeof(*mod->tracepoints_ptrs),
&mod->num_tracepoints);
Basically, since sizeof(*mod->tracepoints_ptrs) is a pointer size
(rather than sizeof(int)), num_tracepoints is erroneously set to half the
size it should be on 64-bit arch. So a module with an odd number of
tracepoints misses the last tracepoint due to effect of integer
division.
So in the module going notifier:
for_each_tracepoint_range(mod->tracepoints_ptrs,
mod->tracepoints_ptrs + mod->num_tracepoints,
tp_module_going_check_quiescent, NULL);
the expression (mod->tracepoints_ptrs + mod->num_tracepoints) actually
evaluates to something within the bounds of the array, but miss the
last tracepoint if the number of tracepoints is odd on 64-bit arch.
Fix this by introducing a new typedef: tracepoint_ptr_t, which
is either "const int" on architectures that have PREL32 relocations,
or "struct tracepoint * const" on architectures that does not have
this feature.
Also provide a new tracepoint_ptr_defer() static inline to
encapsulate deferencing this type rather than duplicate code and
ugly idefs within the for_each_tracepoint_range() implementation.
This issue appears in 4.19-rc kernels, and should ideally be fixed
before the end of the rc cycle.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Jessica Yu <jeyu@kernel.org>
Link: http://lkml.kernel.org/r/20181013191050.22389-1-mathieu.desnoyers@efficios.com
Link: http://lkml.kernel.org/r/20180704083651.24360-7-ard.biesheuvel@linaro.org
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morris <james.morris@microsoft.com>
Cc: James Morris <jmorris@namei.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Thomas Garnier <thgarnie@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
According to rfc7496 section 4.3 or 4.4:
sprstat_policy: This parameter indicates for which PR-SCTP policy
the user wants the information. It is an error to use
SCTP_PR_SCTP_NONE in sprstat_policy. If SCTP_PR_SCTP_ALL is used,
the counters provided are aggregated over all supported policies.
We change to dump pr_assoc and pr_stream all status by SCTP_PR_SCTP_ALL
instead, and return error for SCTP_PR_SCTP_NONE, as it also said "It is
an error to use SCTP_PR_SCTP_NONE in sprstat_policy. "
Fixes: 826d253d57 ("sctp: add SCTP_PR_ASSOC_STATUS on sctp sockopt")
Fixes: d229d48d18 ("sctp: add SCTP_PR_STREAM_STATUS sockopt for prsctp")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
amifd.h and amifdreg.h are only used from amiflop.c, and they're pretty
small, so move the contents to amiflop.c and get rid of the .h files.
This is preparation for adding a struct blk_mq_tag_set to struct
amiga_floppy_struct.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Straight forward conversion, using an internal list to enable the
driver to pull requests at will.
Dynamically allocate the tag set to avoid having to pull in the
block headers for blktrans.h, since various mtd drivers use
block conflicting names for defines and functions.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Tested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Other than asoc pmtu sync from all transports, sctp_assoc_sync_pmtu
is also processing transport pmtu_pending by icmp packets. But it's
meaningless to use sctp_dst_mtu(t->dst) as new pmtu for a transport.
The right pmtu value should come from the icmp packet, and it would
be saved into transport->mtu_info in this patch and used later when
the pmtu sync happens in sctp_sendmsg_to_asoc or sctp_packet_config.
Besides, without this patch, as pmtu can only be updated correctly
when receiving a icmp packet and no place is holding sock lock, it
will take long time if the sock is busy with sending packets.
Note that it doesn't process transport->mtu_info in .release_cb(),
as there is no enough information for pmtu update, like for which
asoc or transport. It is not worth traversing all asocs to check
pmtu_pending. So unlike tcp, sctp does this in tx path, for which
mtu_info needs to be atomic_t.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When commit 270972554c ("[IPV6]: ROUTE: Add Router Reachability
Probing (RFC4191).") introduced router probing, the rt6_probe() function
required that a neighbour entry existed. This neighbour entry is used to
record the timestamp of the last probe via the ->updated field.
Later, commit 2152caea71 ("ipv6: Do not depend on rt->n in rt6_probe().")
removed the requirement for a neighbour entry. Neighbourless routes skip
the interval check and are not rate-limited.
This patch adds rate-limiting for neighbourless routes, by recording the
timestamp of the last probe in the fib6_info itself.
Fixes: 2152caea71 ("ipv6: Do not depend on rt->n in rt6_probe().")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-10-10
This pull request includes some fixes to mlx5 driver,
Please pull and let me know if there's any problem.
For -stable v4.11:
('net/mlx5: Take only bit 24-26 of wqe.pftype_wq for page fault type')
For -stable v4.17:
('net/mlx5: Fix memory leak when setting fpga ipsec caps')
For -stable v4.18:
('net/mlx5: WQ, fixes for fragmented WQ buffers API')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This pattern is repeated throughout all the blk-mq conversions.
Provide a basic helper to get it done.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Will writes:
"More arm64 fixes
- Reject CHAIN PMU events when they are not part of a 64-bit counter
- Fix WARN_ON_ONCE() that triggers for reserved regions that don't
correspond to mapped memory"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: perf: Reject stand-alone CHAIN events for PMUv3
arm64: Fix /proc/iomem for reserved but not memory regions
This spares drivers from #ifdef-ing on CONFIG_PCI if the driver can be
optionally built on machines without PCI bus.
Consistent with acpi_driver_match_device() and similar.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Arnd writes:
"ARM: SoC fixes for 4.19
Two last minute bugfixes, both for NXP platforms:
* The Layerscape 'qbman' infrastructure suffers from probe ordering
bugs in some configurations, a two-patch series adds a hotfix for
this. 4.20 will have a longer set of patches to rework it.
* The old imx53-qsb board regressed in 4.19 after the addition
of cpufreq support, adding a set of explicit operating points
fixes this."
* tag 'armsoc-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
soc: fsl: qman_portals: defer probe after qman's probe
soc: fsl: qbman: add APIs to retrieve the probing status
ARM: dts: imx53-qsb: disable 1.2GHz OPP
It doesn't make sense for a perf event to be configured as a CHAIN event
in isolation, so extend the arm_pmu structure with a ->filter_match()
function to allow the backend PMU implementation to reject CHAIN events
early.
Cc: <stable@vger.kernel.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Linus writes:
"GPIO fix for the v4.19 series:
- Fix up the interrupt parent for the irqdomains."
* tag 'gpio-v4.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Assign gpio_irq_chip::parents to non-stack pointer
Dmitry writes:
"Input updates for v4.19-rc7
- we added a few scheduling points into various input interfaces to
ensure that large writes will not cause RCU stalls
- fixed configuring PS/2 keyboards as wakeup devices on newer
platforms
- added a new Xbox gamepad ID."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: uinput - add a schedule point in uinput_inject_events()
Input: evdev - add a schedule point in evdev_write()
Input: mousedev - add a schedule point in mousedev_write()
Input: i8042 - enable keyboard wakeups by default when s2idle is used
Input: xpad - add support for Xbox1 PDP Camo series gamepad
Stephen writes:
"A couple of warning fixes:
Two fixes from Peter Oberparleiter <oberpar@linux.ibm.com>:
Commit 6b7dca401c ("tracing: Allow gcov profiling on only ftrace subsystem")
uncovered linker problems when using gcov kernel profiling on some
architectures. These problems were likely introduced earlier, and are
possibly related to compiler changes."
* tag 'next-fixes-20181012' of git://git.kernel.org/pub/scm/linux/kernel/git/sfr/next-fixes:
vmlinux.lds.h: Fix linker warnings about orphan .LPBX sections
vmlinux.lds.h: Fix incomplete .text.exit discards
David writes:
"Networking
1) RXRPC receive path fixes from David Howells.
2) Re-export __skb_recv_udp(), from Jiri Kosina.
3) Fix refcounting in u32 classificer, from Al Viro.
4) Userspace netlink ABI fixes from Eugene Syromiatnikov.
5) Don't double iounmap on rmmod in ena driver, from Arthur
Kiyanovski.
6) Fix devlink string attribute handling, we must pull a copy into a
kernel buffer if the lifetime extends past the netlink request.
From Moshe Shemesh.
7) Fix hangs in RDS, from Ka-Cheong Poon.
8) Fix recursive locking lockdep warnings in tipc, from Ying Xue.
9) Clear RX irq correctly in socionext, from Ilias Apalodimas.
10) bcm_sf2 fixes from Florian Fainelli."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
net: dsa: bcm_sf2: Call setup during switch resume
net: dsa: bcm_sf2: Fix unbind ordering
net: phy: sfp: remove sfp_mutex's definition
r8169: set RX_MULTI_EN bit in RxConfig for 8168F-family chips
net: socionext: clear rx irq correctly
net/mlx4_core: Fix warnings during boot on driverinit param set failures
tipc: eliminate possible recursive locking detected by LOCKDEP
selftests: udpgso_bench.sh explicitly requires bash
selftests: rtnetlink.sh explicitly requires bash.
qmi_wwan: Added support for Gemalto's Cinterion ALASxx WWAN interface
tipc: queue socket protocol error messages into socket receive buffer
tipc: set link tolerance correctly in broadcast link
net: ipv4: don't let PMTU updates increase route MTU
net: ipv4: update fnhe_pmtu when first hop's MTU changes
net/ipv6: stop leaking percpu memory in fib6 info
rds: RDS (tcp) hangs on sendto() to unresponding address
net: make skb_partial_csum_set() more robust against overflows
devlink: Add helper function for safely copy string param
devlink: Fix param cmode driverinit for string type
devlink: Fix param set handling for string type
...
Trace events are useful for people who collect data from the
Ftrace outputs. There're people who analyse the relationship
of cpufreq, thermal and hwmon (power/voltage/current) using
the convenient and timestamped Ftrace outputs, while unlike
cpufreq and thermal subsystems the hwmon does not have trace
events supported yet.
So this patch adds initial trace events for the hwmon core.
To call hwmon_attr_base() for aligned attr index numbers, it
also moves the function upward.
Ftrace outputs:
...: hwmon_attr_show_string: index=2, attr_name=in2_label, val=VDD_5V
...: hwmon_attr_show: index=2, attr_name=in2_input, val=5112
...: hwmon_attr_show: index=2, attr_name=curr2_input, val=440
Note that the _attr_show and _attr_store functions are tied
to the _with_info API. So a hwmon driver requiring the trace
events feature should use _with_info API to register a hwmon
device.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Enabling both CONFIG_LD_DEAD_CODE_DATA_ELIMINATION=y and
CONFIG_GCOV_PROFILE_ALL=y results in linker warnings:
warning: orphan section `.data..LPBX1' being placed in
section `.data..LPBX1'.
LD_DEAD_CODE_DATA_ELIMINATION adds compiler flag -fdata-sections. This
option causes GCC to create separate data sections for data objects,
including those generated by GCC internally for gcov profiling. The
names of these objects start with a dot (.LPBX0, .LPBX1), resulting in
section names starting with 'data..'.
As section names starting with 'data..' are used for specific purposes
in the Linux kernel, the linker script does not automatically include
them in the output data section, resulting in the "orphan section"
linker warnings.
Fix this by specifically including sections named "data..LPBX*" in the
data section.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Enabling CONFIG_GCOV_PROFILE_ALL=y causes linker errors on ARM:
`.text.exit' referenced in section `.ARM.exidx.text.exit':
defined in discarded section `.text.exit'
`.text.exit' referenced in section `.fini_array.00100':
defined in discarded section `.text.exit'
And related errors on NDS32:
`.text.exit' referenced in section `.dtors.65435':
defined in discarded section `.text.exit'
The gcov compiler flags cause certain compiler versions to generate
additional destructor-related sections that are not yet handled by the
linker script, resulting in references between discarded and
non-discarded sections.
Since destructors are not used in the Linux kernel, fix this by
discarding these additional sections.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Greentime Hu <green.hu@gmail.com>
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tejun writes:
"cgroup fixes for v4.19-rc7
One cgroup2 threaded mode fix for v4.19-rc7. While threaded mode
isn't used widely (yet) and the bug requires somewhat convoluted
sequence of operations, it causes a userland visible malfunction -
EINVAL on a valid attempt to enable threaded mode. This pull request
contains the fix"
* 'for-4.19-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: Fix dom_cgrp propagation when enabling threaded mode
This adds reasonable comments, but they definitely needs better names.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The MMP2 platform, that uses device tree, has this controller. Let's add
devicetree alongside platform & PCI.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 5aad1de5ea ("ipv4: use separate genid for next hop
exceptions"), exceptions get deprecated separately from cached
routes. In particular, administrative changes don't clear PMTU anymore.
As Stefano described in commit e9fa1495d7 ("ipv6: Reflect MTU changes
on PMTU of exceptions for MTU-less routes"), the PMTU discovered before
the local MTU change can become stale:
- if the local MTU is now lower than the PMTU, that PMTU is now
incorrect
- if the local MTU was the lowest value in the path, and is increased,
we might discover a higher PMTU
Similarly to what commit e9fa1495d7 did for IPv6, update PMTU in those
cases.
If the exception was locked, the discovered PMTU was smaller than the
minimal accepted PMTU. In that case, if the new local MTU is smaller
than the current PMTU, let PMTU discovery figure out if locking of the
exception is still needed.
To do this, we need to know the old link MTU in the NETDEV_CHANGEMTU
notifier. By the time the notifier is called, dev->mtu has been
changed. This patch adds the old MTU as additional information in the
notifier structure, and a new call_netdevice_notifiers_u32() function.
Fixes: 5aad1de5ea ("ipv4: use separate genid for next hop exceptions")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
