Add test cases for bridge backup port and backup nexthop ID, testing
both good and bad flows.
Example truncated output:
# ./test_bridge_backup_port.sh
[...]
Tests passed: 83
Tests failed: 0
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tests whether addition and deletion of a VLAN upper that coincides
with the current PVID setting throws off forwarding.
This selftests is specifically geared towards offloading drivers. In
particular, mlxsw used to fail this selftest, and an earlier patch in this
patchset fixes the issue. However, there's nothing HW-specific in the test
itself (it absolutely is supposed to pass on SW datapath), and therefore it
is put into the generic forwarding directory.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tests whether changes to PVID that coincide with an existing VLAN
upper throw off forwarding. This selftests is specifically geared towards
offloading drivers, but since there's nothing HW-specific in the test
itself (it absolutely is supposed to pass on SW datapath), it is put into
the generic forwarding directory.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an alternative path involving VLAN 777 instead of the current 555. Then
add tests that verify that marking 777 as PVID makes the 555 path not work,
and the 777 path work.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test relies on PVID being configured on the bridge itself. Thus when
it is deconfigured, the system should lose the ability to forward traffic.
Later when it is added again, the ability to forward traffic should be
regained. Add tests to exercise these configuration changes and verify
results.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two helpers to run a ping test that succeeds when the pings themselves
fail.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the IPsec offload test, this requires netdevsim.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2023-07-13
We've added 67 non-merge commits during the last 15 day(s) which contain
a total of 106 files changed, 4444 insertions(+), 619 deletions(-).
The main changes are:
1) Fix bpftool build in presence of stale vmlinux.h,
from Alexander Lobakin.
2) Introduce bpf_me_mcache_free_rcu() and fix OOM under stress,
from Alexei Starovoitov.
3) Teach verifier actual bounds of bpf_get_smp_processor_id()
and fix perf+libbpf issue related to custom section handling,
from Andrii Nakryiko.
4) Introduce bpf map element count, from Anton Protopopov.
5) Check skb ownership against full socket, from Kui-Feng Lee.
6) Support for up to 12 arguments in BPF trampoline, from Menglong Dong.
7) Export rcu_request_urgent_qs_task, from Paul E. McKenney.
8) Fix BTF walking of unions, from Yafang Shao.
9) Extend link_info for kprobe_multi and perf_event links,
from Yafang Shao.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (67 commits)
selftests/bpf: Add selftest for PTR_UNTRUSTED
bpf: Fix an error in verifying a field in a union
selftests/bpf: Add selftests for nested_trust
bpf: Fix an error around PTR_UNTRUSTED
selftests/bpf: add testcase for TRACING with 6+ arguments
bpf, x86: allow function arguments up to 12 for TRACING
bpf, x86: save/restore regs with BPF_DW size
bpftool: Use "fallthrough;" keyword instead of comments
bpf: Add object leak check.
bpf: Convert bpf_cpumask to bpf_mem_cache_free_rcu.
bpf: Introduce bpf_mem_free_rcu() similar to kfree_rcu().
selftests/bpf: Improve test coverage of bpf_mem_alloc.
rcu: Export rcu_request_urgent_qs_task()
bpf: Allow reuse from waiting_for_gp_ttrace list.
bpf: Add a hint to allocated objects.
bpf: Change bpf_mem_cache draining process.
bpf: Further refactor alloc_bulk().
bpf: Factor out inc/dec of active flag into helpers.
bpf: Refactor alloc_bulk().
bpf: Let free_all() return the number of freed elements.
...
====================
Link: https://lore.kernel.org/r/20230714020910.80794-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add selftests for nested_strust to check whehter PTR_UNTRUSTED is cleared
as expected, the result as follows:
#141/1 nested_trust/test_read_cpumask:OK
#141/2 nested_trust/test_skb_field:OK <<<<
#141/3 nested_trust/test_invalid_nested_user_cpus:OK
#141/4 nested_trust/test_invalid_nested_offset:OK
#141/5 nested_trust/test_invalid_skb_field:OK <<<<
#141 nested_trust:OK
The #141/2 and #141/5 are newly added.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Link: https://lore.kernel.org/r/20230713025642.27477-3-laoar.shao@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add fentry_many_args.c and fexit_many_args.c to test the fentry/fexit
with 7/11 arguments. As this feature is not supported by arm64 yet, we
disable these testcases for arm64 in DENYLIST.aarch64. We can combine
them with fentry_test.c/fexit_test.c when arm64 is supported too.
Correspondingly, add bpf_testmod_fentry_test7() and
bpf_testmod_fentry_test11() to bpf_testmod.c
Meanwhile, add bpf_modify_return_test2() to test_run.c to test the
MODIFY_RETURN with 7 arguments.
Add bpf_testmod_test_struct_arg_7/bpf_testmod_test_struct_arg_7 in
bpf_testmod.c to test the struct in the arguments.
And the testcases passed on x86_64:
./test_progs -t fexit
Summary: 5/14 PASSED, 0 SKIPPED, 0 FAILED
./test_progs -t fentry
Summary: 3/2 PASSED, 0 SKIPPED, 0 FAILED
./test_progs -t modify_return
Summary: 1/0 PASSED, 0 SKIPPED, 0 FAILED
./test_progs -t tracing_struct
Summary: 1/0 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/r/20230713040738.1789742-4-imagedong@tencent.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter, wireless and ebpf.
Current release - regressions:
- netfilter: conntrack: gre: don't set assured flag for clash entries
- wifi: iwlwifi: remove 'use_tfh' config to fix crash
Previous releases - regressions:
- ipv6: fix a potential refcount underflow for idev
- icmp6: ifix null-ptr-deref of ip6_null_entry->rt6i_idev in
icmp6_dev()
- bpf: fix max stack depth check for async callbacks
- eth: mlx5e:
- check for NOT_READY flag state after locking
- fix page_pool page fragment tracking for XDP
- eth: igc:
- fix tx hang issue when QBV gate is closed
- fix corner cases for TSN offload
- eth: octeontx2-af: Move validation of ptp pointer before its usage
- eth: ena: fix shift-out-of-bounds in exponential backoff
Previous releases - always broken:
- core: prevent skb corruption on frag list segmentation
- sched:
- cls_fw: fix improper refcount update leads to use-after-free
- sch_qfq: account for stab overhead in qfq_enqueue
- netfilter:
- report use refcount overflow
- prevent OOB access in nft_byteorder_eval
- wifi: mt7921e: fix init command fail with enabled device
- eth: ocelot: fix oversize frame dropping for preemptible TCs
- eth: fec: recycle pages for transmitted XDP frames"
* tag 'net-6.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (79 commits)
selftests: tc-testing: add test for qfq with stab overhead
net/sched: sch_qfq: account for stab overhead in qfq_enqueue
selftests: tc-testing: add tests for qfq mtu sanity check
net/sched: sch_qfq: reintroduce lmax bound check for MTU
wifi: cfg80211: fix receiving mesh packets without RFC1042 header
wifi: rtw89: debug: fix error code in rtw89_debug_priv_send_h2c_set()
net: txgbe: fix eeprom calculation error
net/sched: make psched_mtu() RTNL-less safe
net: ena: fix shift-out-of-bounds in exponential backoff
netdevsim: fix uninitialized data in nsim_dev_trap_fa_cookie_write()
net/sched: flower: Ensure both minimum and maximum ports are specified
MAINTAINERS: Add another mailing list for QUALCOMM ETHQOS ETHERNET DRIVER
docs: netdev: update the URL of the status page
wifi: iwlwifi: remove 'use_tfh' config to fix crash
xdp: use trusted arguments in XDP hints kfuncs
bpf: cpumap: Fix memory leak in cpu_map_update_elem
wifi: airo: avoid uninitialized warning in airo_get_rate()
octeontx2-pf: Add additional check for MCAM rules
net: dsa: Removed unneeded of_node_put in felix_parse_ports_node
net: fec: use netdev_err_once() instead of netdev_err()
...
Pull tracing fixes from Steven Rostedt:
- Fix some missing-prototype warnings
- Fix user events struct args (did not include size of struct)
When creating a user event, the "struct" keyword is to denote that
the size of the field will be passed in. But the parsing failed to
handle this case.
- Add selftest to struct sizes for user events
- Fix sample code for direct trampolines.
The sample code for direct trampolines attached to handle_mm_fault().
But the prototype changed and the direct trampoline sample code was
not updated. Direct trampolines needs to have the arguments correct
otherwise it can fail or crash the system.
- Remove unused ftrace_regs_caller_ret() prototype.
- Quiet false positive of FORTIFY_SOURCE
Due to backward compatibility, the structure used to save stack
traces in the kernel had a fixed size of 8. This structure is
exported to user space via the tracing format file. A change was made
to allow more than 8 functions to be recorded, and user space now
uses the size field to know how many functions are actually in the
stack.
But the structure still has size of 8 (even though it points into the
ring buffer that has the required amount allocated to hold a full
stack.
This was fine until the fortifier noticed that the
memcpy(&entry->caller, stack, size) was greater than the 8 functions
and would complain at runtime about it.
Hide this by using a pointer to the stack location on the ring buffer
instead of using the address of the entry structure caller field.
- Fix a deadloop in reading trace_pipe that was caused by a mismatch
between ring_buffer_empty() returning false which then asked to read
the data, but the read code uses rb_num_of_entries() that returned
zero, and causing a infinite "retry".
- Fix a warning caused by not using all pages allocated to store ftrace
functions, where this can happen if the linker inserts a bunch of
"NULL" entries, causing the accounting of how many pages needed to be
off.
- Fix histogram synthetic event crashing when the start event is
removed and the end event is still using a variable from it
- Fix memory leak in freeing iter->temp in tracing_release_pipe()
* tag 'trace-v6.5-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Fix memory leak of iter->temp when reading trace_pipe
tracing/histograms: Add histograms to hist_vars if they have referenced variables
tracing: Stop FORTIFY_SOURCE complaining about stack trace caller
ftrace: Fix possible warning on checking all pages used in ftrace_process_locs()
ring-buffer: Fix deadloop issue on reading trace_pipe
tracing: arm64: Avoid missing-prototype warnings
selftests/user_events: Test struct size match cases
tracing/user_events: Fix struct arg size match check
x86/ftrace: Remove unsued extern declaration ftrace_regs_caller_ret()
arm64: ftrace: Add direct call trampoline samples support
samples: ftrace: Save required argument registers in sample trampolines
Pull HID fixes from Benjamin Tissoires:
- AMD SFH shift-out-of-bounds fix (Basavaraj Natikar)
- avoid struct memcpy overrun warning in the hid-hyperv module (Arnd
Bergmann)
- a quick HID kselftests script fix for our CI to be happy (Benjamin
Tissoires)
- various fixes and additions of device IDs
* tag 'for-linus-2023071101' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: amd_sfh: Fix for shift-out-of-bounds
HID: amd_sfh: Rename the float32 variable
HID: input: fix mapping for camera access keys
HID: logitech-hidpp: Add wired USB id for Logitech G502 Lightspeed
HID: nvidia-shield: Pack inner/related declarations in HOSTCMD reports
HID: hyperv: avoid struct memcpy overrun warning
selftests: hid: fix vmtests.sh not running make headers
Pull more RISC-V updates from Palmer Dabbelt:
- A bunch of fixes/cleanups from the first part of the merge window,
mostly related to ACPI and vector as those were large
- Some documentation improvements, mostly related to the new code
- The "riscv,isa" DT key is deprecated
- Support for link-time dead code elimination
- Support for minor fault registration in userfaultd
- A handful of cleanups around CMO alternatives
* tag 'riscv-for-linus-6.5-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (23 commits)
riscv: mm: mark noncoherent_supported as __ro_after_init
riscv: mm: mark CBO relate initialization funcs as __init
riscv: errata: thead: only set cbom size & noncoherent during boot
riscv: Select HAVE_ARCH_USERFAULTFD_MINOR
RISC-V: Document the ISA string parsing rules for ACPI
risc-v: Fix order of IPI enablement vs RCU startup
mm: riscv: fix an unsafe pte read in huge_pte_alloc()
dt-bindings: riscv: deprecate riscv,isa
RISC-V: drop error print from riscv_hartid_to_cpuid()
riscv: Discard vector state on syscalls
riscv: move memblock_allow_resize() after linear mapping is ready
riscv: Enable ARCH_SUSPEND_POSSIBLE for s2idle
riscv: vdso: include vdso/vsyscall.h for vdso_data
selftests: Test RISC-V Vector's first-use handler
riscv: vector: clear V-reg in the first-use trap
riscv: vector: only enable interrupts in the first-use trap
RISC-V: Fix up some vector state related build failures
RISC-V: Document that V registers are clobbered on syscalls
riscv: disable HAVE_LD_DEAD_CODE_DATA_ELIMINATION for LLD
riscv: enable HAVE_LD_DEAD_CODE_DATA_ELIMINATION
...
Pull mode documentation updates from Jonathan Corbet:
"A half-dozen late arriving docs patches. They are mostly fixes, but we
also have a kernel-doc tweak for enums and the long-overdue removal of
the outdated and redundant patch-submission comments at the top of the
MAINTAINERS file"
* tag 'docs-6.5-2' of git://git.lwn.net/linux:
scripts: kernel-doc: support private / public marking for enums
Documentation: KVM: SEV: add a missing backtick
Documentation: ACPI: fix typo in ssdt-overlays.rst
Fix documentation of panic_on_warn
docs: remove the tips on how to submit patches from MAINTAINERS
docs: fix typo in zh_TW and zh_CN translation
Add a new map test, map_percpu_stats.c, which is checking the correctness of
map's percpu elements counters. For supported maps the test upserts a number
of elements, checks the correctness of the counters, then deletes all the
elements and checks again that the counters sum drops down to zero.
The following map types are tested:
* BPF_MAP_TYPE_HASH, BPF_F_NO_PREALLOC
* BPF_MAP_TYPE_PERCPU_HASH, BPF_F_NO_PREALLOC
* BPF_MAP_TYPE_HASH,
* BPF_MAP_TYPE_PERCPU_HASH,
* BPF_MAP_TYPE_LRU_HASH
* BPF_MAP_TYPE_LRU_PERCPU_HASH
* BPF_MAP_TYPE_LRU_HASH, BPF_F_NO_COMMON_LRU
* BPF_MAP_TYPE_LRU_PERCPU_HASH, BPF_F_NO_COMMON_LRU
* BPF_MAP_TYPE_HASH_OF_MAPS
Signed-off-by: Anton Protopopov <aspsk@isovalent.com>
Acked-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20230706133932.45883-6-aspsk@isovalent.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Use the bpf_timer_set_callback helper to mark timer_cb as an async
callback, and put a direct call to timer_cb in the main subprog.
As the check_stack_max_depth happens after the do_check pass, the order
does not matter. Without the previous fix, the test passes successfully.
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20230705144730.235802-3-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The benchmark could be used to compare the performance of hash map
operations and the memory usage between different flavors of bpf memory
allocator (e.g., no bpf ma vs bpf ma vs reuse-after-gp bpf ma). It also
could be used to check the performance improvement or the memory saving
provided by optimization.
The benchmark creates a non-preallocated hash map which uses bpf memory
allocator and shows the operation performance and the memory usage of
the hash map under different use cases:
(1) overwrite
Each CPU overwrites nonoverlapping part of hash map. When each CPU
completes overwriting of 64 elements in hash map, it increases the
op_count.
(2) batch_add_batch_del
Each CPU adds then deletes nonoverlapping part of hash map in batch.
When each CPU adds and deletes 64 elements in hash map, it increases
the op_count twice.
(3) add_del_on_diff_cpu
Each two-CPUs pair adds and deletes nonoverlapping part of map
cooperatively. When each CPU adds or deletes 64 elements in hash map,
it will increase the op_count.
The following is the benchmark results when comparing between different
flavors of bpf memory allocator. These tests are conducted on a KVM guest
with 8 CPUs and 16 GB memory. The command line below is used to do all
the following benchmarks:
./bench htab-mem --use-case $name ${OPTS} -w3 -d10 -a -p8
These results show that preallocated hash map has both better performance
and smaller memory footprint.
(1) non-preallocated + no bpf memory allocator (v6.0.19)
use kmalloc() + call_rcu
overwrite per-prod-op: 11.24 ± 0.07k/s, avg mem: 82.64 ± 26.32MiB, peak mem: 119.18MiB
batch_add_batch_del per-prod-op: 18.45 ± 0.10k/s, avg mem: 50.47 ± 14.51MiB, peak mem: 94.96MiB
add_del_on_diff_cpu per-prod-op: 14.50 ± 0.03k/s, avg mem: 4.64 ± 0.73MiB, peak mem: 7.20MiB
(2) preallocated
OPTS=--preallocated
overwrite per-prod-op: 191.42 ± 0.09k/s, avg mem: 1.24 ± 0.00MiB, peak mem: 1.49MiB
batch_add_batch_del per-prod-op: 221.83 ± 0.17k/s, avg mem: 1.23 ± 0.00MiB, peak mem: 1.49MiB
add_del_on_diff_cpu per-prod-op: 39.66 ± 0.31k/s, avg mem: 1.47 ± 0.13MiB, peak mem: 1.75MiB
(3) normal bpf memory allocator
overwrite per-prod-op: 126.59 ± 0.02k/s, avg mem: 2.26 ± 0.00MiB, peak mem: 2.74MiB
batch_add_batch_del per-prod-op: 83.37 ± 0.20k/s, avg mem: 2.14 ± 0.17MiB, peak mem: 2.74MiB
add_del_on_diff_cpu per-prod-op: 21.25 ± 0.24k/s, avg mem: 17.50 ± 3.32MiB, peak mem: 28.87MiB
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20230704025039.938914-1-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth, bpf and wireguard.
Current release - regressions:
- nvme-tcp: fix comma-related oops after sendpage changes
Current release - new code bugs:
- ptp: make max_phase_adjustment sysfs device attribute invisible
when not supported
Previous releases - regressions:
- sctp: fix potential deadlock on &net->sctp.addr_wq_lock
- mptcp:
- ensure subflow is unhashed before cleaning the backlog
- do not rely on implicit state check in mptcp_listen()
Previous releases - always broken:
- net: fix net_dev_start_xmit trace event vs skb_transport_offset()
- Bluetooth:
- fix use-bdaddr-property quirk
- L2CAP: fix multiple UaFs
- ISO: use hci_sync for setting CIG parameters
- hci_event: fix Set CIG Parameters error status handling
- hci_event: fix parsing of CIS Established Event
- MGMT: fix marking SCAN_RSP as not connectable
- wireguard: queuing: use saner cpu selection wrapping
- sched: act_ipt: various bug fixes for iptables <> TC interactions
- sched: act_pedit: add size check for TCA_PEDIT_PARMS_EX
- dsa: fixes for receiving PTP packets with 8021q and sja1105 tagging
- eth: sfc: fix null-deref in devlink port without MAE access
- eth: ibmvnic: do not reset dql stats on NON_FATAL err
Misc:
- xsk: honor SO_BINDTODEVICE on bind"
* tag 'net-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
nfp: clean mc addresses in application firmware when closing port
selftests: mptcp: pm_nl_ctl: fix 32-bit support
selftests: mptcp: depend on SYN_COOKIES
selftests: mptcp: userspace_pm: report errors with 'remove' tests
selftests: mptcp: userspace_pm: use correct server port
selftests: mptcp: sockopt: return error if wrong mark
selftests: mptcp: sockopt: use 'iptables-legacy' if available
selftests: mptcp: connect: fail if nft supposed to work
mptcp: do not rely on implicit state check in mptcp_listen()
mptcp: ensure subflow is unhashed before cleaning the backlog
s390/qeth: Fix vipa deletion
octeontx-af: fix hardware timestamp configuration
net: dsa: sja1105: always enable the send_meta options
net: dsa: tag_sja1105: fix MAC DA patching from meta frames
net: Replace strlcpy with strscpy
pptp: Fix fib lookup calls.
mlxsw: spectrum_router: Fix an IS_ERR() vs NULL check
net/sched: act_pedit: Add size check for TCA_PEDIT_PARMS_EX
xsk: Honor SO_BINDTODEVICE on bind
ptp: Make max_phase_adjustment sysfs device attribute invisible when not supported
...
When building the kselftests out-of-tree, e.g. ...
| make ARCH=riscv CROSS_COMPILE=riscv64-linux-gnu- \
| O=/tmp/kselftest headers
| make ARCH=riscv CROSS_COMPILE=riscv64-linux-gnu- \
| O=/tmp/kselftest HOSTCC=gcc FORMAT= \
| SKIP_TARGETS="arm64 ia64 powerpc sparc64 x86 sgx" \
| -C tools/testing/selftests gen_tar
... the kselftest build would not pick up the correct GENDIR path, and
therefore not including autoconf.h.
Correct that by taking $(O) into consideration when figuring out the
GENDIR path.
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230705113926.751791-3-bjorn@kernel.org
When using pm_nl_ctl to validate userspace path-manager's behaviours, it
was failing on 32-bit architectures ~half of the time.
pm_nl_ctl was not reporting any error but the command was not doing what
it was expected to do. As a result, the expected linked event was not
triggered after and the test failed.
This is due to the fact the token given in argument to the application
was parsed as an integer with atoi(): in a 32-bit arch, if the number
was bigger than INT_MAX, 2147483647 was used instead.
This can simply be fixed by using strtoul() instead of atoi().
The errors have been seen "by chance" when manually looking at the
results from LKFT.
Fixes: 9a0b36509d ("selftests: mptcp: support MPTCP_PM_CMD_ANNOUNCE")
Cc: stable@vger.kernel.org
Fixes: ecd2a77d67 ("selftests: mptcp: support MPTCP_PM_CMD_REMOVE")
Fixes: cf8d0a6dfd ("selftests: mptcp: support MPTCP_PM_CMD_SUBFLOW_CREATE")
Fixes: 57cc361b8d ("selftests: mptcp: support MPTCP_PM_CMD_SUBFLOW_DESTROY")
Fixes: ca188a25d4 ("selftests: mptcp: userspace PM support for MP_PRIO signals")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPTCP selftests are using TCP SYN Cookies for quite a while now, since
v5.9.
Some CIs don't have this config option enabled and this is causing
issues in the tests:
# ns1 MPTCP -> ns1 (10.0.1.1:10000 ) MPTCP (duration 167ms) sysctl: cannot stat /proc/sys/net/ipv4/tcp_syncookies: No such file or directory
# [ OK ]./mptcp_connect.sh: line 554: [: -eq: unary operator expected
There is no impact in the results but the test is not doing what it is
supposed to do.
Fixes: fed61c4b58 ("selftests: mptcp: make 2nd net namespace use tcp syn cookies unconditionally")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an error was detected when checking the marks, a message was
correctly printed mentioning the error but followed by another one
saying everything was OK and the selftest was not marked as failed as
expected.
Now the 'ret' variable is directly set to 1 in order to make sure the
exit is done with an error, similar to what is done in other functions.
While at it, the error is correctly propagated to the caller.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: dc65fe82fb ("selftests: mptcp: add packet mark test case")
Cc: stable@vger.kernel.org
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of "external" errors when preparing the environment for the
TProxy tests, the subtests were marked as skipped.
This is fine but it means these errors are ignored. On MPTCP Public CI,
we do want to catch such issues and mark the selftest as failed if there
are such issues. We can then use mptcp_lib_fail_if_expected_feature()
helper that has been recently added to fail if needed.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 5fb62e9cd3 ("selftests: mptcp: add tproxy test case")
Cc: stable@vger.kernel.org
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel cmdline option panic_on_warn expects an integer, it is not a
plain option as documented. A number of uses in the tree figured this
already, and use panic_on_warn=1 for their purpose.
Adjust a comment which otherwise may mislead people in the future.
Fixes: 9e3961a097 ("kernel: add panic_on_warn")
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Pull kvm updates from Paolo Bonzini:
"ARM64:
- Eager page splitting optimization for dirty logging, optionally
allowing for a VM to avoid the cost of hugepage splitting in the
stage-2 fault path.
- Arm FF-A proxy for pKVM, allowing a pKVM host to safely interact
with services that live in the Secure world. pKVM intervenes on
FF-A calls to guarantee the host doesn't misuse memory donated to
the hyp or a pKVM guest.
- Support for running the split hypervisor with VHE enabled, known as
'hVHE' mode. This is extremely useful for testing the split
hypervisor on VHE-only systems, and paves the way for new use cases
that depend on having two TTBRs available at EL2.
- Generalized framework for configurable ID registers from userspace.
KVM/arm64 currently prevents arbitrary CPU feature set
configuration from userspace, but the intent is to relax this
limitation and allow userspace to select a feature set consistent
with the CPU.
- Enable the use of Branch Target Identification (FEAT_BTI) in the
hypervisor.
- Use a separate set of pointer authentication keys for the
hypervisor when running in protected mode, as the host is untrusted
at runtime.
- Ensure timer IRQs are consistently released in the init failure
paths.
- Avoid trapping CTR_EL0 on systems with Enhanced Virtualization
Traps (FEAT_EVT), as it is a register commonly read from userspace.
- Erratum workaround for the upcoming AmpereOne part, which has
broken hardware A/D state management.
RISC-V:
- Redirect AMO load/store misaligned traps to KVM guest
- Trap-n-emulate AIA in-kernel irqchip for KVM guest
- Svnapot support for KVM Guest
s390:
- New uvdevice secret API
- CMM selftest and fixes
- fix racy access to target CPU for diag 9c
x86:
- Fix missing/incorrect #GP checks on ENCLS
- Use standard mmu_notifier hooks for handling APIC access page
- Drop now unnecessary TR/TSS load after VM-Exit on AMD
- Print more descriptive information about the status of SEV and
SEV-ES during module load
- Add a test for splitting and reconstituting hugepages during and
after dirty logging
- Add support for CPU pinning in demand paging test
- Add support for AMD PerfMonV2, with a variety of cleanups and minor
fixes included along the way
- Add a "nx_huge_pages=never" option to effectively avoid creating NX
hugepage recovery threads (because nx_huge_pages=off can be toggled
at runtime)
- Move handling of PAT out of MTRR code and dedup SVM+VMX code
- Fix output of PIC poll command emulation when there's an interrupt
- Add a maintainer's handbook to document KVM x86 processes,
preferred coding style, testing expectations, etc.
- Misc cleanups, fixes and comments
Generic:
- Miscellaneous bugfixes and cleanups
Selftests:
- Generate dependency files so that partial rebuilds work as
expected"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (153 commits)
Documentation/process: Add a maintainer handbook for KVM x86
Documentation/process: Add a label for the tip tree handbook's coding style
KVM: arm64: Fix misuse of KVM_ARM_VCPU_POWER_OFF bit index
RISC-V: KVM: Remove unneeded semicolon
RISC-V: KVM: Allow Svnapot extension for Guest/VM
riscv: kvm: define vcpu_sbi_ext_pmu in header
RISC-V: KVM: Expose IMSIC registers as attributes of AIA irqchip
RISC-V: KVM: Add in-kernel virtualization of AIA IMSIC
RISC-V: KVM: Expose APLIC registers as attributes of AIA irqchip
RISC-V: KVM: Add in-kernel emulation of AIA APLIC
RISC-V: KVM: Implement device interface for AIA irqchip
RISC-V: KVM: Skeletal in-kernel AIA irqchip support
RISC-V: KVM: Set kvm_riscv_aia_nr_hgei to zero
RISC-V: KVM: Add APLIC related defines
RISC-V: KVM: Add IMSIC related defines
RISC-V: KVM: Implement guest external interrupt line management
KVM: x86: Remove PRIx* definitions as they are solely for user space
s390/uv: Update query for secret-UVCs
s390/uv: replace scnprintf with sysfs_emit
s390/uvdevice: Add 'Lock Secret Store' UVC
...
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty/serial driver updates for 6.5-rc1.
Included in here are:
- tty_audit code cleanups from Jiri
- more 8250 cleanups from Ilpo
- samsung_tty driver bugfixes
- 8250 lock port updates
- usual fsl_lpuart driver updates and fixes
- other small serial driver fixes and updates, full details in the
shortlog
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits)
tty_audit: make data of tty_audit_log() const
tty_audit: make tty pointers in exposed functions const
tty_audit: make icanon a bool
tty_audit: invert the condition in tty_audit_log()
tty_audit: use kzalloc() in tty_audit_buf_alloc()
tty_audit: use TASK_COMM_LEN for task comm
Revert "8250: add support for ASIX devices with a FIFO bug"
serial: atmel: don't enable IRQs prematurely
tty: serial: Add Nuvoton ma35d1 serial driver support
tty: serial: fsl_lpuart: add earlycon for imx8ulp platform
tty: serial: imx: fix rs485 rx after tx
selftests: tty: add selftest for tty timestamp updates
tty: tty_io: update timestamps on all device nodes
tty: fix hang on tty device with no_room set
serial: core: fix -EPROBE_DEFER handling in init
serial: 8250_omap: Use force_suspend and resume for system suspend
tty: serial: samsung_tty: Use abs() to simplify some code
tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() when iterating clk
tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() in case of error
serial: 8250: Apply FSL workarounds also without SERIAL_8250_CONSOLE
...
Packets bound for peers can queue up prior to the device private key
being set. For example, if persistent keepalive is set, a packet is
queued up to be sent as soon as the device comes up. However, if the
private key hasn't been set yet, the handshake message never sends, and
no timer is armed to retry, since that would be pointless.
But, if a user later sets a private key, the expectation is that those
queued packets, such as a persistent keepalive, are actually sent. So
adjust the configuration logic to account for this edge case, and add a
test case to make sure this works.
Maxim noticed this with a wg-quick(8) config to the tune of:
[Interface]
PostUp = wg set %i private-key somefile
[Peer]
PublicKey = ...
Endpoint = ...
PersistentKeepalive = 25
Here, the private key gets set after the device comes up using a PostUp
script, triggering the bug.
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Cc: stable@vger.kernel.org
Reported-by: Maxim Cournoyer <maxim.cournoyer@gmail.com>
Tested-by: Maxim Cournoyer <maxim.cournoyer@gmail.com>
Link: https://lore.kernel.org/wireguard/87fs7xtqrv.fsf@gmail.com/
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
