The search for promisc entries was always done on the first port,
While the addition is done on the correct port.
This lead to resource leackage of promisc entries on the second
port and brought to a state where we could no longer enter to
promiscuous mode after enough iterations of "ifconfig promisc"
on the second port.
Fix that by using the correct port when searching.
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since VFs may be mapped to VMs which aren't trusted entities, flow
steering rules attached through the wrapper on behalf of VFs must be
checked to make sure that their L2 specification relate to MAC address
assigned to that VF, and add L2 specification if its missing.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow for usage of the flow steering Firmware structures in more locations over the driver,
such as the resource tracker, move them from mcg.c to common header files.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
~0 can not be casted to u8. Instead of using the IPACK_ANY_ID for the format
field we introduce a new IPACK_ANY_FORMAT specifically for that field and
defined as 0xff.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Taprogge <jens.taprogge@taprogge.org>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: fixes for v3.6-rc4
Here's a rather big set of fixes for v3.6-rc4.
There are some fixes for bugs which have been pending for a long
time and only now were uncovered, like the musb and dwc3 patches.
We have some remaining fixes for the ep->desc patch series from
Ido, a fix for renesas DMA usage, IRQ check on musb's DMA and
an oops fix on musb Host implementation.
All patches have been pending on linux-usb for a long time and
shouldn't cause any further regressions.
c1dcad2d32 added a new driver configured by
HID_LENOVO_TPKBD but made the hid_have_special_driver entry non-optional which
lead to a recognized but non-working device if the new driver wasn't
configured (which is the correct default).
Signed-off-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
* Fix for TLB flushing introduced in v3.6
* Fix Xen-SWIOTLB not using proper DMA mask - device had 64bit but
in a 32-bit kernel we need to allocate for coherent pages from a
32-bit pool.
* When trying to re-use P2M nodes we had a one-off error and triggered
a BUG_ON check with specific CONFIG_ option.
* When doing FLR in Xen-PCI-backend we would first do FLR then save the
PCI configuration space. We needed to do it the other way around.
* tag 'stable/for-linus-3.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pciback: Fix proper FLR steps.
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
Pull PCI updates from Bjorn Helgaas:
"Power management
- PCI/PM: Enable D3/D3cold by default for most devices
- PCI/PM: Keep parent bridge active when probing device
- PCI/PM: Fix config reg access for D3cold and bridge suspending
- PCI/PM: Add ABI document for sysfs file d3cold_allowed
Core
- PCI: Don't print anything while decoding is disabled"
* tag '3.6-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Don't print anything while decoding is disabled
PCI/PM: Add ABI document for sysfs file d3cold_allowed
PCI/PM: Fix config reg access for D3cold and bridge suspending
PCI/PM: Keep parent bridge active when probing device
PCI/PM: Enable D3/D3cold by default for most devices
Consistently use iio_push_to_buffer instead of manually calling the buffers
store_to callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Since iio_trigger_poll() calls generic_handle_irq() it need to be called from
hardirq context. The sysfs trigger is kicked from userspace, so it is obviously
not possible to fulfill this requirement by calling iio_trigger_poll directly.
As a workaround commit 1f785681 ("staging:iio:trigger sysfs userspace trigger
rework.") added iio_trigger_poll_chained() which uses handle_nested_irq instead
of generic_handle_irq. This in itself is a hack and only works by chance.
handle_nested_irq is intended to be called from the threaded interrupt handler
of the parent IRQ. Using handle_nested_irq is also problematic since it will
only call the threaded handler of the IRQ. But quite a few IIO drivers rely on
their hardirq handler being called or undefined behaviour will occur.
This patch uses the irq_work framework to schedule the call to
iio_trigger_poll() from hardirq context, which fixes the issues described above.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In 3.6-rc3, without this patch, the following error occurs with a modular build:
ERROR: "gen_split_key" [drivers/crypto/caam/caamhash.ko] undefined!
ERROR: "gen_split_key" [drivers/crypto/caam/caamalg.ko] undefined!
Signed-off-by: Ben Collins <ben.c@servergy.com>
Cc: Yuan Kang <Yuan.Kang@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Added usage id processing for ALS. This uses IIO
interfaces for triggered buffer to present data to user
mode.This uses HID sensor framework for registering callback
events from the sensor hub.
Signed-off-by: srinivas pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added usage id processing for Compass 3D. This uses IIO
interfaces for triggered buffer to present data to user
mode.This uses HID sensor framework for registering callback
events from the sensor hub.
Signed-off-by: srinivas pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
gcc complains about some potentially uninitalized variables here, yet it
can not happen, due to an enumerated type (either the board is one type
or the other.) Make the compiler happy by providing a default case
option that makes the logic a bit simpler for it to determine that there
really isn't a problem here.
Cc: H Hartley Sweeten <hartleys@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added usage id processing for Gyroscope 3D. This uses IIO
interfaces for triggered buffer to present data to user
mode.This uses HID sensor framework for registering callback
events from the sensor hub.
Signed-off-by: srinivas pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added usage id processing for Accelerometer 3D.This uses IIO
interfaces for triggered buffer to present data to user
mode.This uses HID sensor framework for registering callback
events from the sensor hub.
Signed-off-by: srinivas pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch contains the common code, which is used by all HID sensors.
There are some common set of attributes, which every hid sensor
needs it. This patch contains all such attributes processing.
Also the trigger interface is common among all HID sensors. This
patch contains common trigger functions utilized by all HID sensors.
Signed-off-by: srinivas pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Adding processing for HID Sensor usage table as defined by
HID 1.12, Request #: HUTRR39, dated 05 May, 2011.
This driver uses HID driver framework to register, send and
receive events.
This uses MFD framework, so that actual processing for a
specific usage id can be done in a different driver. For
example an accelerometer driver can be a separate driver and
use the interface provided by this driver to register for
events.
Signed-off-by: srinivas pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Adding Intel and STM sensor hub in the list of drivers with
specialized driver.
Signed-off-by: srinivas pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added hysteresis to the list of channel info enumeration, shared
/separate bit defines and to postfix channel info strings.
Signed-off-by: srinivas pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pull ARM SoC bug fixes from Olof Johansson:
"Mostly Renesas and Atmel bugfixes this time, targeting boot and build
problems. A couple of patches for gemini and kirkwood as well. On a
whole nothing very controversial."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: gemini: fix the gemini build
ARM: shmobile: armadillo800eva: enable rw rootfs mount
ARM: Kirkwood: Fix 'SZ_1M' undeclared here for db88f6281-bp-setup.c
ARM: shmobile: mackerel: fixup usb module order
ARM: shmobile: armadillo800eva: fixup: sound card detection order
ARM: shmobile: marzen: fixup smsc911x id for regulator
ARM: at91/feature-removal-schedule: delay at91_mci removal
ARM: mach-shmobile: armadillo800eva: Enable power button as wakeup source
ARM: mach-shmobile: armadillo800eva: Fix GPIO buttons descriptions
ARM: at91/dts: remove partial parameter in at91sam9g25ek.dts
ARM: at91/clock: fix PLLA overclock warning
ARM: at91: fix rtc-at91sam9 irq issue due to sparse irq support
ARM: at91: fix system timer irq issue due to sparse irq support
ARM: shmobile: sh73a0: fixup RELOC_BASE of intca_irq_pins_desc
If xfernotready is received and there is no request in request_list then
REQUEST_PENDING flag must be set, so that next request in ep queue is executed.
In case of isoc transfer, if xfernotready is already elapsed and even first
request has not been queued to request_list, then issue END TRANSFER, so that
you can receive xfernotready again and can have notion of current microframe.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Earlier we used to check for ep->ep.desc to figure out if this ep has
already been enabled and if so, abort.
Ido Shayevitz removed the usb_endpoint_descriptor from private udc
structure 5a6506f00 ("usb: gadget: Update at91_udc to use
usb_endpoint_descriptor inside the struct usb_ep") but did not fix up
the ep_enable condition because _now_ the member is always true and we
can't check if this ep is enabled twice.
Cc: Ido Shayevitz <idos@codeaurora.org>
Tested-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Tested-by: Mario Isidoro <Mario.Isidoro@tecmic.pt>
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The driver was converted to the new start/stop interface in f3d8bf34c2
("usb: gadget: at91_udc: convert to new style start/stop interface").
I overlooked that the driver is overwritting the private data which is
used by the composite framework. The udc driver doesn't read it, it is
only written here.
Tested-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Tested-by: Mario Isidoro <Mario.Isidoro@tecmic.pt>
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Populate the resources for xhci afresh instead of directly using the
*struct resource* of core. *resource* structure has parent, sibling,
child pointers which should be filled only by resource API's. By
directly using the *resource* pointer of core in xhci, these parent,
sibling, child pointers are already populated even before
*platform_device_add* causing side effects.
Cc: stable@vger.kernel.org # v3.4, v3.5
Reported-by: Ruchika Kharwar <ruchika@ti.com>
Tested-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dma_controller_create() in this MUSB DMA driver only regards 0 as a wrong IRQ
number, despite platform_get_irq_byname() that it calls returns -ENXIO in that
case. It leads to calling request_irq() with a negative IRQ number, and when it
naturally fails, the following is printed to the console:
request_irq -6 failed!
and the DMA controller is not created.
Fix this function to filter out the error values as well as 0.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On platform_device_add() failure, the TUSB6010 glue layer forgets to call
platform_device_put() -- probably due to a typo...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
when using musb_urb_enqueue to submit three urbs to the same endpoint, when
hep->hcpriv is NULL, qh will be allocated when the first urb is completed.
When the IRQ completes the next two urbs, qh->hep->hcpriv will be set to NULL.
Now the second urb get musb->lock and executes musb_schedule(), but
next_urb(qh) is NULL, so musb_start_urb will Oops.
[ balbi@ti.com : practically rewrote commit log so it makes sense ]
Signed-off-by: mayuzheng <myz147@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Without a reply for USB_DT_BOS the USB3 mode does not work since
448b6eb1 ("USB: Make sure to fetch the BOS desc for roothubs.).
Cc: stable@vger.kernel.org #v3.5
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If USB2 host controller probes fine but USB3 does not then we don't
remove the USB controller properly and lock up the system while the HUB
code will try to enumerate the USB2 controller and access memory which
is no longer available in case the dummy_hcd was compiled as a module.
This is a problem since 448b6eb1 ("USB: Make sure to fetch the BOS desc
for roothubs.) if used in USB3 mode because dummy does not provide this
descriptor and explodes later.
Cc: stable@vger.kernel.org # v3.5
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case of ep0 out, if length is not aligned to maxpacket size then we use
dwc->ep_bounce_addr for dma transfer and not request->dma. Since, we have
alreday done memcpy from dwc->ep0_bounce to request->buf, so we do not need to
issue cache sync function. In fact, cache sync function will bring wrong data
in request->buf from request->dma in this scenario.
So, cache sync function must not be executed in case of ep0 bounced.
Cc: <stable@vger.kernel.org> # v3.4 v3.5
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If f_fs.c and u_serial.c are combined together using #include, which has
been a common practice so far, the pr_vdebug macro is defined multiple
times. Define it only once.
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB autosuspend suspends vhci_hcd. In this process hcd_bus_suspend gets
executed which puts vhci_hcd in suspend state and calls vhci_hub_status.
vhci_hub_status function checks hub state and if it is in suspend state,
usb_hcd_resume_root_hub gets executed which resumes hub and if hub is
idle, again autosuspend puts it in suspend state and this goes on.
vhci_hub_status should resume hub only when hub port is in suspend state
and hub port status has changed.
Signed-off-by: navin patidar <navinp@cdac.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Almost all of usbip assumes that the_controller->lock is acquired
before vdev->priv_lock. The exception is in
vhci_device_unlink_cleanup(), where locks are acquired in the
reverse order. This leads to occasional deadlocks.
Fixing this is a bit fiddly, as the_controller->lock can't be held
when calling usb_hcd_unlink_urb_from_ep() in the middle of the list
traversal. As I can't rule out concurrent callers to this function
(perhaps it is safe?), the code here becomes slightly uglier - when
locks are dropped in the middle so the list may have emptied itself
(not even list_for_each_entry_safe is safe here).
Signed-off-by: Bernard Blackham <b-linuxgit@largestprime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If "pool_id" is negative then it leads to a read before the start of the
array. If "cli_id" is out of bounds then it leads to a NULL dereference
of "cli". GCC would have warned about that bug except that we
initialized the warning message away.
Also it's better to put the parameter names into the function
declaration in the .h file. It serves as a kind of documentation.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we do FLR and save PCI config we did it in the wrong order.
The end result was that if a PCI device was unbind from
its driver, then binded to xen-pciback, and then back to its
driver we would get:
> lspci -s 04:00.0
04:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
13:42:12 # 4 :~/
> echo "0000:04:00.0" > /sys/bus/pci/drivers/pciback/unbind
> modprobe e1000e
e1000e: Intel(R) PRO/1000 Network Driver - 2.0.0-k
e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
e1000e 0000:04:00.0: Disabling ASPM L0s L1
e1000e 0000:04:00.0: enabling device (0000 -> 0002)
xen: registering gsi 48 triggering 0 polarity 1
Already setup the GSI :48
e1000e 0000:04:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
e1000e: probe of 0000:04:00.0 failed with error -2
This fixes it by first saving the PCI configuration space, then
doing the FLR.
Reported-by: Ren, Yongjie <yongjie.ren@intel.com>
Reported-and-Tested-by: Tobias Geiger <tobias.geiger@vido.info>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: stable@vger.kernel.org
