Simon Wunderlich says:
====================
This cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- update include for min/max helpers, by Sven Eckelmann
- add infrastructure and netlink functions for routing algo selection,
by Sven Eckelmann (2 patches)
- drop deprecated debugfs and sysfs support and obsoleted
functionality, by Sven Eckelmann (3 patches)
- drop unused include in fragmentation.c, by Simon Wunderlich
* tag 'batadv-next-pullrequest-20201204' of git://git.open-mesh.org/linux-merge:
batman-adv: Drop unused soft-interface.h include in fragmentation.c
batman-adv: Drop legacy code for auto deleting mesh interfaces
batman-adv: Drop deprecated debugfs support
batman-adv: Drop deprecated sysfs support
batman-adv: Allow selection of routing algorithm over rtnetlink
batman-adv: Prepare infrastructure for newlink settings
batman-adv: Add new include for min/max helpers
batman-adv: Start new development cycle
====================
Link: https://lore.kernel.org/r/20201204154631.21063-1-sw@simonwunderlich.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Zapping pages is required only if we are calling vm_insert_page into a
region where pages had previously been mapped. Receive zerocopy allows
reusing such regions, and hitherto called zap_page_range() before
calling vm_insert_page() in that range.
zap_page_range() can also be triggered from userspace with
madvise(MADV_DONTNEED). If userspace is configured to call this before
reusing a segment, or if there was nothing mapped at this virtual
address to begin with, we can avoid calling zap_page_range() under the
socket lock. That said, if userspace does not do that, then we are
still responsible for calling zap_page_range().
This patch adds a flag that the user can use to hint to the kernel
that a zap is not required. If the flag is not set, or if an older
user application does not have a flags field at all, then the kernel
calls zap_page_range as before. Also, if the flag is set but a zap is
still required, the kernel performs that zap as necessary. Thus
incorrectly indicating that a zap can be avoided does not change the
correctness of operation. It also increases the batchsize for
vm_insert_pages and prefetches the page struct for the batch since
we're about to bump the refcount.
An alternative mechanism could be to not have a flag, assume by
default a zap is not needed, and fall back to zapping if needed.
However, this would harm performance for older applications for which
a zap is necessary, and thus we implement it with an explicit flag
so newer applications can opt in.
When using RPC-style traffic with medium sized (tens of KB) RPCs, this
change yields an efficency improvement of about 30% for QPS/CPU usage.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When TCP receive zerocopy does not successfully map the entire
requested space, it outputs a 'hint' that the caller should recvmsg().
Augment zerocopy to accept a user buffer that it tries to copy this
hint into - if it is possible to copy the entire hint, it will do so.
This elides a recvmsg() call for received traffic that isn't exactly
page-aligned in size.
This was tested with RPC-style traffic of arbitrary sizes. Normally,
each received message required at least one getsockopt() call, and one
recvmsg() call for the remaining unaligned data.
With this change, almost all of the recvmsg() calls are eliminated,
leading to a savings of about 25%-50% in number of system calls
for RPC-style workloads.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SRv6 End.DT4 is defined in the SRv6 Network Programming [1].
The SRv6 End.DT4 is used to implement IPv4 L3VPN use-cases in
multi-tenants environments. It decapsulates the received packets and it
performs IPv4 routing lookup in the routing table of the tenant.
The SRv6 End.DT4 Linux implementation leverages a VRF device in order to
force the routing lookup into the associated routing table.
To make the End.DT4 work properly, it must be guaranteed that the routing
table used for routing lookup operations is bound to one and only one
VRF during the tunnel creation. Such constraint has to be enforced by
enabling the VRF strict_mode sysctl parameter, i.e:
$ sysctl -wq net.vrf.strict_mode=1.
At JANOG44, LINE corporation presented their multi-tenant DC architecture
using SRv6 [2]. In the slides, they reported that the Linux kernel is
missing the support of SRv6 End.DT4 behavior.
The SRv6 End.DT4 behavior can be instantiated using a command similar to
the following:
$ ip route add 2001:db8::1 encap seg6local action End.DT4 vrftable 100 dev eth0
We introduce the "vrftable" extension in iproute2 in a following patch.
[1] https://tools.ietf.org/html/draft-ietf-spring-srv6-network-programming
[2] https://speakerdeck.com/line_developers/line-data-center-networking-with-srv6
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-12-03
The main changes are:
1) Support BTF in kernel modules, from Andrii.
2) Introduce preferred busy-polling, from Björn.
3) bpf_ima_inode_hash() and bpf_bprm_opts_set() helpers, from KP Singh.
4) Memcg-based memory accounting for bpf objects, from Roman.
5) Allow bpf_{s,g}etsockopt from cgroup bind{4,6} hooks, from Stanislav.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (118 commits)
selftests/bpf: Fix invalid use of strncat in test_sockmap
libbpf: Use memcpy instead of strncpy to please GCC
selftests/bpf: Add fentry/fexit/fmod_ret selftest for kernel module
selftests/bpf: Add tp_btf CO-RE reloc test for modules
libbpf: Support attachment of BPF tracing programs to kernel modules
libbpf: Factor out low-level BPF program loading helper
bpf: Allow to specify kernel module BTFs when attaching BPF programs
bpf: Remove hard-coded btf_vmlinux assumption from BPF verifier
selftests/bpf: Add CO-RE relocs selftest relying on kernel module BTF
selftests/bpf: Add support for marking sub-tests as skipped
selftests/bpf: Add bpf_testmod kernel module for testing
libbpf: Add kernel module BTF support for CO-RE relocations
libbpf: Refactor CO-RE relocs to not assume a single BTF object
libbpf: Add internal helper to load BTF data by FD
bpf: Keep module's btf_data_size intact after load
bpf: Fix bpf_put_raw_tracepoint()'s use of __module_address()
selftests/bpf: Add Userspace tests for TCP_WINDOW_CLAMP
bpf: Adds support for setting window clamp
samples/bpf: Fix spelling mistake "recieving" -> "receiving"
bpf: Fix cold build of test_progs-no_alu32
...
====================
Link: https://lore.kernel.org/r/20201204021936.85653-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A batadv net_device is associated to a B.A.T.M.A.N. routing algorithm. This
algorithm has to be selected before the interface is initialized and cannot
be changed after that. The only way to select this algorithm was a module
parameter which specifies the default algorithm used during the creation of
the net_device.
This module parameter is writeable over
/sys/module/batman_adv/parameters/routing_algo and thus allows switching of
the routing algorithm:
1. change routing_algo parameter
2. create new batadv net_device
But this is not race free because another process can be scheduled between
1 + 2 and in that time frame change the routing_algo parameter again.
It is much cleaner to directly provide this information inside the
rtnetlink's RTM_NEWLINK message. The two processes would be (in regards of
the creation parameter of their batadv interfaces) be isolated. This also
eases the integration of batadv devices inside tools like network-manager
or systemd-networkd which are not expecting to operate on /sys before a new
net_device is created.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batadv generic netlink family can be used to retrieve the current state
and set various configuration settings. But there are also settings which
must be set before the actual interface is created.
The rtnetlink already uses IFLA_INFO_DATA to allow net_device families to
transfer such configurations. The minimal required functionality for this
is now available for the batadv rtnl_link_ops. Also a new IFLA class of
attributes will be attached to it because rtnetlink only allows 51
different attributes but batadv_nl_attrs already contains 62 attributes.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Add ability for user-space programs to specify non-vmlinux BTF when attaching
BTF-powered BPF programs: raw_tp, fentry/fexit/fmod_ret, LSM, etc. For this,
attach_prog_fd (now with the alias name attach_btf_obj_fd) should specify FD
of a module or vmlinux BTF object. For backwards compatibility reasons,
0 denotes vmlinux BTF. Only kernel BTF (vmlinux or module) can be specified.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201203204634.1325171-11-andrii@kernel.org
Background:
Broadcast and multicast packages are enqueued for later processing.
This queue was previously hardcoded to 1000.
This proved insufficient for handling very high packet rates.
This resulted in packet drops for multicast.
While at the same time unicast worked fine.
The change:
This patch make the queue length adjustable to accommodate
for environments with very high multicast packet rate.
But still keeps the default value of 1000 unless specified.
The queue length is specified as a request per macvlan
using the IFLA_MACVLAN_BC_QUEUE_LEN parameter.
The actual used queue length will then be the maximum of
any macvlan connected to the same port. The actual used
queue length for the port can be retrieved (read only)
by the IFLA_MACVLAN_BC_QUEUE_LEN_USED parameter for verification.
This will be followed up by a patch to iproute2
in order to adjust the parameter from userspace.
Signed-off-by: Thomas Karlsson <thomas.karlsson@paneda.se>
Link: https://lore.kernel.org/r/dd4673b2-7eab-edda-6815-85c67ce87f63@paneda.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Saeed Mahameed says:
====================
mlx5-next-2020-12-02
Low level mlx5 updates required by both netdev and rdma trees.
* tag 'mlx5-next-2020-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Treat host PF vport as other (non eswitch manager) vport
net/mlx5: Enable host PF HCA after eswitch is initialized
net/mlx5: Rename peer_pf to host_pf
net/mlx5: Make API mlx5_core_is_ecpf accept const pointer
net/mlx5: Export steering related functions
net/mlx5: Expose other function ifc bits
net/mlx5: Expose IP-in-IP TX and RX capability bits
net/mlx5: Update the hardware interface definition for vhca state
net/mlx5: Update the list of the PCI supported devices
net/mlx5: Avoid exposing driver internal command helpers
net/mlx5: Add ts_cqe_to_dest_cqn related bits
net/mlx5: Add misc4 to mlx5_ifc_fte_match_param_bits
net/mlx5: Check dr mask size against mlx5_match_param size
net/mlx5: Add sampler destination type
net/mlx5: Add sample offload hardware bits and structures
====================
Link: https://lore.kernel.org/r/20201203011010.213440-1-saeedm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce get link command which loops through
all available links of all available link groups. It
uses the SMC-R linkgroup list as entry point, not
the socket list, which makes linkgroup diagnosis
possible, in case linkgroup does not contain active
connections anymore.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce get linkgroup command which loops through
all available SMCR linkgroups. It uses the SMC-R linkgroup
list as entry point, not the socket list, which makes
linkgroup diagnosis possible, in case linkgroup does not
contain active connections anymore.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add new netlink command to obtain system information
of the smc module.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The existing busy-polling mode, enabled by the SO_BUSY_POLL socket
option or system-wide using the /proc/sys/net/core/busy_read knob, is
an opportunistic. That means that if the NAPI context is not
scheduled, it will poll it. If, after busy-polling, the budget is
exceeded the busy-polling logic will schedule the NAPI onto the
regular softirq handling.
One implication of the behavior above is that a busy/heavy loaded NAPI
context will never enter/allow for busy-polling. Some applications
prefer that most NAPI processing would be done by busy-polling.
This series adds a new socket option, SO_PREFER_BUSY_POLL, that works
in concert with the napi_defer_hard_irqs and gro_flush_timeout
knobs. The napi_defer_hard_irqs and gro_flush_timeout knobs were
introduced in commit 6f8b12d661 ("net: napi: add hard irqs deferral
feature"), and allows for a user to defer interrupts to be enabled and
instead schedule the NAPI context from a watchdog timer. When a user
enables the SO_PREFER_BUSY_POLL, again with the other knobs enabled,
and the NAPI context is being processed by a softirq, the softirq NAPI
processing will exit early to allow the busy-polling to be performed.
If the application stops performing busy-polling via a system call,
the watchdog timer defined by gro_flush_timeout will timeout, and
regular softirq handling will resume.
In summary; Heavy traffic applications that prefer busy-polling over
softirq processing should use this option.
Example usage:
$ echo 2 | sudo tee /sys/class/net/ens785f1/napi_defer_hard_irqs
$ echo 200000 | sudo tee /sys/class/net/ens785f1/gro_flush_timeout
Note that the timeout should be larger than the userspace processing
window, otherwise the watchdog will timeout and fall back to regular
softirq processing.
Enable the SO_BUSY_POLL/SO_PREFER_BUSY_POLL options on your socket.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/bpf/20201130185205.196029-2-bjorn.topel@gmail.com
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To provide support for ChaCha-Poly cipher we need to define
specific constants and structures.
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the openvswitch module is not accepting the correctly formated
netlink message for the TTL decrement action. For both setting and getting
the dec_ttl action, the actions should be nested in the
OVS_DEC_TTL_ATTR_ACTION attribute as mentioned in the openvswitch.h uapi.
When the original patch was sent, it was tested with a private OVS userspace
implementation. This implementation was unfortunately not upstreamed and
reviewed, hence an erroneous version of this patch was sent out.
Leaving the patch as-is would cause problems as the kernel module could
interpret additional attributes as actions and vice-versa, due to the
actions not being encapsulated/nested within the actual attribute, but
being concatinated after it.
Fixes: 744676e777 ("openvswitch: add TTL decrement action")
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/160622121495.27296.888010441924340582.stgit@wsfd-netdev64.ntdv.lab.eng.bos.redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide a wrapper function to get the IMA hash of an inode. This helper
is useful in fingerprinting files (e.g executables on execution) and
using these fingerprints in detections like an executable unlinking
itself.
Since the ima_inode_hash can sleep, it's only allowed for sleepable
LSM hooks.
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20201124151210.1081188-3-kpsingh@chromium.org
Extend MRP to support LC mode(link check) for the interconnect port.
This applies only to the interconnect ring.
Opposite to RC mode(ring check) the LC mode is using CFM frames to
detect when the link goes up or down and based on that the userspace
will need to react.
One advantage of the LC mode over RC mode is that there will be fewer
frames in the normal rings. Because RC mode generates InTest on all
ports while LC mode sends CFM frame only on the interconnect port.
All 4 nodes part of the interconnect ring needs to have the same mode.
And it is not possible to have running LC and RC mode at the same time
on a node.
Whenever the MIM starts it needs to detect the status of the other 3
nodes in the interconnect ring so it would send a frame called
InLinkStatus, on which the clients needs to reply with their link
status.
This patch adds InLinkStatus frame type and extends existing rules on
how to forward this frame.
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20201124082525.273820-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix reload stats structure exposed to the user. Change stats structure
hierarchy to have the reload action as a parent of the stat entry and
then stat entry includes value per limit. This will also help to avoid
string concatenation on iproute2 output.
Reload stats structure before this fix:
"stats": {
"reload": {
"driver_reinit": 2,
"fw_activate": 1,
"fw_activate_no_reset": 0
}
}
After this fix:
"stats": {
"reload": {
"driver_reinit": {
"unspecified": 2
},
"fw_activate": {
"unspecified": 1,
"no_reset": 0
}
}
Fixes: a254c26426 ("devlink: Add reload stats")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/1606109785-25197-1-git-send-email-moshe@mellanox.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for data length code modifications for Classical CAN.
The netlink configuration interface always allowed to pass any value
that fits into a byte, therefore only the modification process had to be
extended to handle the raw DLC represenation of Classical CAN frames.
When a DLC value from 0 .. F is provided for Classical CAN frame
modifications the 'len' value is modified as-is with the exception that
potentially existing 9 .. F DLC values in the len8_dlc element are moved
to the 'len' element for the modification operation by mod_retrieve_ccdlc().
After the modification the Classical CAN frame DLC information is brought
back into the correct format by mod_store_ccdlc() which is filling 'len'
and 'len8_dlc' accordingly.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201119084921.2621-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
ISO 11898-1 Chapter 8.4.2.3 defines a 4 bit data length code (DLC) table which
maps the DLC to the payload length of the CAN frame in bytes:
DLC -> payload length
0 .. 8 -> 0 .. 8
9 .. 15 -> 8
Although the DLC values 8 .. 15 in Classical CAN always result in a payload
length of 8 bytes these DLC values are transparently transmitted on the CAN
bus. As the struct can_frame only provides a 'len' element (formerly 'can_dlc')
which contains the plain payload length ( 0 .. 8 ) of the CAN frame, the raw
DLC is not visible to the application programmer, e.g. for testing use-cases.
To access the raw DLC values 9 .. 15 the len8_dlc element is introduced, which
is only valid when the payload length 'len' is 8 and the DLC is greater than 8.
The len8_dlc element is filled by the CAN interface driver and used for CAN
frame creation by the CAN driver when the CAN_CTRLMODE_CC_LEN8_DLC flag is
supported by the driver and enabled via netlink configuration interface.
Reported-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201110101852.1973-2-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The helper uses CLOCK_MONOTONIC_COARSE source of time that is less
accurate but more performant.
We have a BPF CGROUP_SKB firewall that supports event logging through
bpf_perf_event_output(). Each event has a timestamp and currently we use
bpf_ktime_get_ns() for it. Use of bpf_ktime_get_coarse_ns() saves ~15-20
ns in time required for event logging.
bpf_ktime_get_ns():
EgressLogByRemoteEndpoint 113.82ns 8.79M
bpf_ktime_get_coarse_ns():
EgressLogByRemoteEndpoint 95.40ns 10.48M
Signed-off-by: Dmitrii Banshchikov <me@ubique.spb.ru>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20201117184549.257280-1-me@ubique.spb.ru
The helper allows modification of certain bits on the linux_binprm
struct starting with the secureexec bit which can be updated using the
BPF_F_BPRM_SECUREEXEC flag.
secureexec can be set by the LSM for privilege gaining executions to set
the AT_SECURE auxv for glibc. When set, the dynamic linker disables the
use of certain environment variables (like LD_PRELOAD).
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20201117232929.2156341-1-kpsingh@chromium.org
The DLCI driver (dlci.c) implements the Frame Relay protocol. However,
we already have another newer and better implementation of Frame Relay
provided by the HDLC_FR driver (hdlc_fr.c).
The DLCI driver's implementation of Frame Relay is used by only one
hardware driver in the kernel - the SDLA driver (sdla.c).
The SDLA driver provides Frame Relay support for the Sangoma S50x devices.
However, the vendor provides their own driver (along with their own
multi-WAN-protocol implementations including Frame Relay), called WANPIPE.
I believe most users of the hardware would use the vendor-provided WANPIPE
driver instead.
(The WANPIPE driver was even once in the kernel, but was deleted in
commit 8db60bcf30 ("[WAN]: Remove broken and unmaintained Sangoma
drivers.") because the vendor no longer updated the in-kernel WANPIPE
driver.)
Cc: Mike McLagan <mike.mclagan@linux.org>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201114150921.685594-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-11-14
1) Add BTF generation for kernel modules and extend BTF infra in kernel
e.g. support for split BTF loading and validation, from Andrii Nakryiko.
2) Support for pointers beyond pkt_end to recognize LLVM generated patterns
on inlined branch conditions, from Alexei Starovoitov.
3) Implements bpf_local_storage for task_struct for BPF LSM, from KP Singh.
4) Enable FENTRY/FEXIT/RAW_TP tracing program to use the bpf_sk_storage
infra, from Martin KaFai Lau.
5) Add XDP bulk APIs that introduce a defer/flush mechanism to optimize the
XDP_REDIRECT path, from Lorenzo Bianconi.
6) Fix a potential (although rather theoretical) deadlock of hashtab in NMI
context, from Song Liu.
7) Fixes for cross and out-of-tree build of bpftool and runqslower allowing build
for different target archs on same source tree, from Jean-Philippe Brucker.
8) Fix error path in htab_map_alloc() triggered from syzbot, from Eric Dumazet.
9) Move functionality from test_tcpbpf_user into the test_progs framework so it
can run in BPF CI, from Alexander Duyck.
10) Lift hashtab key_size limit to be larger than MAX_BPF_STACK, from Florian Lehner.
Note that for the fix from Song we have seen a sparse report on context
imbalance which requires changes in sparse itself for proper annotation
detection where this is currently being discussed on linux-sparse among
developers [0]. Once we have more clarification/guidance after their fix,
Song will follow-up.
[0] https://lore.kernel.org/linux-sparse/CAHk-=wh4bx8A8dHnX612MsDO13st6uzAz1mJ1PaHHVevJx_ZCw@mail.gmail.com/T/https://lore.kernel.org/linux-sparse/20201109221345.uklbp3lzgq6g42zb@ltop.local/T/
* git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (66 commits)
net: mlx5: Add xdp tx return bulking support
net: mvpp2: Add xdp tx return bulking support
net: mvneta: Add xdp tx return bulking support
net: page_pool: Add bulk support for ptr_ring
net: xdp: Introduce bulking for xdp tx return path
bpf: Expose bpf_d_path helper to sleepable LSM hooks
bpf: Augment the set of sleepable LSM hooks
bpf: selftest: Use bpf_sk_storage in FENTRY/FEXIT/RAW_TP
bpf: Allow using bpf_sk_storage in FENTRY/FEXIT/RAW_TP
bpf: Rename some functions in bpf_sk_storage
bpf: Folding omem_charge() into sk_storage_charge()
selftests/bpf: Add asm tests for pkt vs pkt_end comparison.
selftests/bpf: Add skb_pkt_end test
bpf: Support for pointers beyond pkt_end.
tools/bpf: Always run the *-clean recipes
tools/bpf: Add bootstrap/ to .gitignore
bpf: Fix NULL dereference in bpf_task_storage
tools/bpftool: Fix build slowdown
tools/runqslower: Build bpftool using HOSTCC
tools/runqslower: Enable out-of-tree build
...
====================
Link: https://lore.kernel.org/r/20201114020819.29584-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Johannes Berg says:
====================
Some updates:
* injection/radiotap updates for new test capabilities
* remove WDS support - even years ago when we turned
it off by default it was already basically unusable
* support for HE (802.11ax) rates for beacons
* support for some vendor-specific HE rates
* many other small features/cleanups
* tag 'mac80211-next-for-net-next-2020-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (21 commits)
nl80211: fix kernel-doc warning in the new SAE attribute
cfg80211: remove WDS code
mac80211: remove WDS-related code
rt2x00: remove WDS code
b43legacy: remove WDS code
b43: remove WDS code
carl9170: remove WDS code
ath9k: remove WDS code
wireless: remove CONFIG_WIRELESS_WDS
mac80211: assure that certain drivers adhere to DONT_REORDER flag
mac80211: don't overwrite QoS TID of injected frames
mac80211: adhere to Tx control flag that prevents frame reordering
mac80211: add radiotap flag to assure frames are not reordered
mac80211: save HE oper info in BSS config for mesh
cfg80211: add support to configure HE MCS for beacon rate
nl80211: fix beacon tx rate mask validation
nl80211/cfg80211: fix potential infinite loop
cfg80211: Add support to calculate and report 4096-QAM HE rates
cfg80211: Add support to configure SAE PWE value to drivers
ieee80211: Add definition for WFA DPP
...
====================
Link: https://lore.kernel.org/r/20201113101148.25268-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull GPIO fixes from Linus Walleij:
"Some GPIO fixes I've collected with the help of Bartosz.
Nothing special about them: all are driver and kbuild fixes + some
documentation fixes:
- Tidy up a missed function call in the designware driver when
converting to gpiolib irqchip
- Fix some bitmasks in the Aspeed driver
- Fix some kerneldoc warnings and minor bugs in the improved
userspace API documentation
- Revert the revert of the OMAP fix for lost edge wakeup interrupts:
the fix needs to stay in
- Fix a compile error when deselecting the character device
- A bunch of IRQ fixes on the idio GPIO drivers
- Fix an off-by-one error in the SiFive GPIO driver"
* tag 'gpio-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: sifive: Fix SiFive gpio probe
gpio: pcie-idio-24: Enable PEX8311 interrupts
gpio: pcie-idio-24: Fix IRQ Enable Register value
gpio: pcie-idio-24: Fix irq mask when masking
gpiolib: fix sysfs when cdev is not selected
Revert "Revert "gpio: omap: Fix lost edge wake-up interrupts""
gpio: uapi: clarify the meaning of 'empty' char arrays
gpio: uapi: remove whitespace
gpio: uapi: kernel-doc formatting improvements
gpio: uapi: comment consistency
gpio: uapi: fix kernel-doc warnings
gpio: aspeed: fix ast2600 bank properties
gpio: dwapb: Fix missing conversion to GPIO-lib-based IRQ-chip
Allocate ID for vmlinux BTF. This makes it visible when iterating over all BTF
objects in the system. To allow distinguishing vmlinux BTF (and later kernel
module BTF) from user-provided BTFs, expose extra kernel_btf flag, as well as
BTF name ("vmlinux" for vmlinux BTF, will equal to module's name for module
BTF). We might want to later allow specifying BTF name for user-provided BTFs
as well, if that makes sense. But currently this is reserved only for
in-kernel BTFs.
Having in-kernel BTFs exposed IDs will allow to extend BPF APIs that require
in-kernel BTF type with ability to specify BTF types from kernel modules, not
just vmlinux BTF. This will be implemented in a follow up patch set for
fentry/fexit/fmod_ret/lsm/etc.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201110011932.3201430-3-andrii@kernel.org
One use case of PACKET_FANOUT is lockless reception with one socket
per CPU. 256 is a practical limit on increasingly many machines.
Increase PACKET_FANOUT_MAX to 64K. Expand setsockopt PACKET_FANOUT to
take an extra argument max_num_members. Also explicitly define a
fanout_args struct, instead of implicitly casting to an integer. This
documents the API and simplifies the control flow.
If max_num_members is not specified or is set to 0, then 256 is used,
same as before.
Signed-off-by: Tanner Love <tannerlove@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When udp_memory_allocated is at the limit, __udp_enqueue_schedule_skb
will return a -ENOBUFS, and skb will be dropped in __udp_queue_rcv_skb
without any counters being done. It's hard to find out what happened
once this happen.
So we introduce a UDP_MIB_MEMERRORS to do this job. Well, this change
looks friendly to the existing users, such as netstat:
$ netstat -u -s
Udp:
0 packets received
639 packets to unknown port received.
158689 packet receive errors
180022 packets sent
RcvbufErrors: 20930
MemErrors: 137759
UdpLite:
IpExt:
InOctets: 257426235
OutOctets: 257460598
InNoECTPkts: 181177
v2:
- Fix some alignment problems
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Link: https://lore.kernel.org/r/1604627354-43207-1-git-send-email-dong.menglong@zte.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull sound fixes from Takashi Iwai:
"Quite a bunch of small fixes that have been gathered since the last
pull, including changes like below:
- HD-audio runtime PM fixes and refactoring
- HD-audio and USB-audio quirks
- SOF warning fix
- Various ASoC device-specific fixes for Intel, Qualcomm, etc"
* tag 'sound-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (26 commits)
ALSA: usb-audio: Add implicit feedback quirk for Qu-16
ASoC: mchp-spdiftx: Do not set Validity bit(s)
ALSA: usb-audio: Add implicit feedback quirk for MODX
ALSA: usb-audio: add usb vendor id as DSD-capable for Khadas devices
ALSA: hda/realtek - Enable headphone for ASUS TM420
ALSA: hda: prevent undefined shift in snd_hdac_ext_bus_get_link()
ASoC: qcom: lpass-cpu: Fix clock disable failure
ASoC: qcom: lpass-sc7180: Fix MI2S bitwidth field bit positions
ASoC: codecs: wcd9335: Set digital gain range correctly
ASoC: codecs: wcd934x: Set digital gain range correctly
ALSA: hda: Reinstate runtime_allow() for all hda controllers
ALSA: hda: Separate runtime and system suspend
ALSA: hda: Refactor codec PM to use direct-complete optimization
ALSA: hda/realtek - Fixed HP headset Mic can't be detected
ALSA: usb-audio: Add implicit feedback quirk for Zoom UAC-2
ALSA: make snd_kcontrol_new name a normal string
ALSA: fix kernel-doc markups
ASoC: SOF: loader: handle all SOF_IPC_EXT types
ASoC: cs42l51: manage mclk shutdown delay
ASoC: qcom: sdm845: set driver name correctly
...
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.10-rc3, including fixes from wireless, can, and
netfilter subtrees.
Current merge window - bugs in new features:
- can: isotp: isotp_rcv_cf(): enable RX timeout handling in
listen-only mode
Previous releases - regressions:
- mac80211:
- don't require VHT elements for HE on 2.4 GHz
- fix regression where EAPOL frames were sent in plaintext
- netfilter:
- ipset: Update byte and packet counters regardless of whether
they match
- ip_tunnel: fix over-mtu packet send by allowing fragmenting even if
inner packet has IP_DF (don't fragment) set in its header (when
TUNNEL_DONT_FRAGMENT flag is not set on the tunnel dev)
- net: fec: fix MDIO probing for some FEC hardware blocks
- ip6_tunnel: set inner ipproto before ip6_tnl_encap to un-break gso
support
- sctp: Fix COMM_LOST/CANT_STR_ASSOC err reporting on big-endian
platforms, sparse-related fix used the wrong integer size
Previous releases - always broken:
- netfilter: use actual socket sk rather than skb sk when routing
harder
- r8169: work around short packet hw bug on RTL8125 by padding frames
- net: ethernet: ti: cpsw: disable PTPv1 hw timestamping
advertisement, the hardware does not support it
- chelsio/chtls: fix always leaking ctrl_skb and another leak caused
by a race condition
- fix drivers incorrectly writing into skbs on TX:
- cadence: force nonlinear buffers to be cloned
- gianfar: Account for Tx PTP timestamp in the skb headroom
- gianfar: Replace skb_realloc_headroom with skb_cow_head for PTP
- can: flexcan:
- remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
- add ECC initialization for VF610 and LX2160A
- flexcan_remove(): disable wakeup completely
- can: fix packet echo functionality:
- peak_canfd: fix echo management when loopback is on
- make sure skbs are not freed in IRQ context in case they need to
be dropped
- always clone the skbs to make sure they have a reference on the
socket, and prevent it from disappearing
- fix real payload length return value for RTR frames
- can: j1939: return failure on bind if netdev is down, rather than
waiting indefinitely
Misc:
- IPv6: reply ICMP error if the first fragment don't include all
headers to improve compliance with RFC 8200"
* tag 'net-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
ionic: check port ptr before use
r8169: work around short packet hw bug on RTL8125
net: openvswitch: silence suspicious RCU usage warning
chelsio/chtls: fix always leaking ctrl_skb
chelsio/chtls: fix memory leaks caused by a race
can: flexcan: flexcan_remove(): disable wakeup completely
can: flexcan: add ECC initialization for VF610
can: flexcan: add ECC initialization for LX2160A
can: flexcan: remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
can: mcp251xfd: remove unneeded break
can: mcp251xfd: mcp251xfd_regmap_nocrc_read(): fix semicolon.cocci warnings
can: mcp251xfd: mcp251xfd_regmap_crc_read(): increase severity of CRC read error messages
can: peak_canfd: pucan_handle_can_rx(): fix echo management when loopback is on
can: peak_usb: peak_usb_get_ts_time(): fix timestamp wrapping
can: peak_usb: add range checking in decode operations
can: xilinx_can: handle failure cases of pm_runtime_get_sync
can: ti_hecc: ti_hecc_probe(): add missed clk_disable_unprepare() in error path
can: isotp: padlen(): make const array static, makes object smaller
can: isotp: isotp_rcv_cf(): enable RX timeout handling in listen-only mode
can: isotp: Explain PDU in CAN_ISOTP help text
...
The flag indicates to user space that the nexthop is not programmed to
forward packets in hardware, but rather to trap them to the CPU. This is
needed, for example, when the MAC of the nexthop neighbour is not
resolved and packets should reach the CPU to trigger neighbour
resolution.
The flag will be used in subsequent patches by netdevsim to test nexthop
objects programming to device drivers and in the future by mlxsw as
well.
Changes since RFC:
* Reword commit message
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The currently available bpf_get_current_task returns an unsigned integer
which can be used along with BPF_CORE_READ to read data from
the task_struct but still cannot be used as an input argument to a
helper that accepts an ARG_PTR_TO_BTF_ID of type task_struct.
In order to implement this helper a new return type, RET_PTR_TO_BTF_ID,
is added. This is similar to RET_PTR_TO_BTF_ID_OR_NULL but does not
require checking the nullness of returned pointer.
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20201106103747.2780972-6-kpsingh@chromium.org
Similar to bpf_local_storage for sockets and inodes add local storage
for task_struct.
The life-cycle of storage is managed with the life-cycle of the
task_struct. i.e. the storage is destroyed along with the owning task
with a callback to the bpf_task_storage_free from the task_free LSM
hook.
The BPF LSM allocates an __rcu pointer to the bpf_local_storage in
the security blob which are now stackable and can co-exist with other
LSMs.
The userspace map operations can be done by using a pid fd as a key
passed to the lookup, update and delete operations.
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20201106103747.2780972-3-kpsingh@chromium.org
Add support to configure SAE PWE preference from userspace to drivers in
both AP and STA modes. This is needed for cases where the driver takes
care of Authentication frame processing (SME in the driver) so that
correct enforcement of the acceptable PWE derivation mechanism can be
performed.
The userspace applications can pass the sae_pwe value using the
NL80211_ATTR_SAE_PWE attribute in the NL80211_CMD_CONNECT and
NL80211_CMD_START_AP commands to the driver. This allows selection
between the hunting-and-pecking loop and hash-to-element options for PWE
derivation. For backwards compatibility, this new attribute is optional
and if not included, the driver is notified of the value being
unspecified.
Signed-off-by: Rohan Dutta <drohan@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20201027100910.22283-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
