Pull arm64 fixes from Will Deacon:
"Three arm64 fixes for -rc4.
One of them is just a trivial documentation fix, whereas the other two
address a warning in the kexec code and a crash in ftrace on systems
implementing BTI.
The latter patch has a couple of ugly ifdefs which Mark plans to clean
up separately, but as-is the patch is straightforward for backporting
to stable kernels.
Summary:
- Add missing BTI landing instructions to the ftrace*_caller
trampolines
- Fix kexec() WARN when DEBUG_VIRTUAL is enabled
- Fix PAC documentation by removing stale references to compiler
flags"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: ftrace: add missing BTIs
arm64: kexec: use __pa_symbol(empty_zero_page)
arm64: update PAC description for kernel
Pull i2c fixes from Wolfram Sang:
"I2C has another set of driver bugfixes, mostly for the stm32f7 driver"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: rk3x: Handle a spurious start completion interrupt flag
i2c: stm32f7: use proper DMAENGINE API for termination
i2c: stm32f7: stop dma transfer in case of NACK
i2c: stm32f7: recover the bus on access timeout
i2c: stm32f7: flush TX FIFO upon transfer errors
i2c: cbus-gpio: set atomic transfer callback
Pull libata fixes from Damien Le Moal:
"Two sparse warning fixes and a couple of patches to fix an issue with
sata_fsl driver module removal:
- A couple of patches to avoid sparse warnings in libata-sata and in
the pata_falcon driver (from Yang and Finn).
- A couple of sata_fsl driver patches fixing IRQ free and proc
unregister on module removal (from Baokun)"
* tag 'libata-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: replace snprintf in show functions with sysfs_emit
sata_fsl: fix warning in remove_proc_entry when rmmod sata_fsl
sata_fsl: fix UAF in sata_fsl_port_stop when rmmod sata_fsl
pata_falcon: Avoid type warnings from sparse
server->dstaddr can change when the DNS mapping for the
server hostname changes. But conn_id is a u64 counter
that is incremented each time a new TCP connection
is setup. So use only that as a key.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
The fscache client cookie uses the server address
(and port) as the cookie key. This is a problem when
nosharesock is used. Two different connections will
use duplicate cookies. Avoid this by adding
server->conn_id to the key, so that it's guaranteed
that cookie will not be duplicated.
Also, for secondary channels of a session, copy the
fscache pointer from the primary channel. The primary
channel is guaranteed not to go away as long as secondary
channels are in use. Also addresses minor problem found
by kernel test robot.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
The logic for initializing tcon->resource_id is done inside
cifs_root_iget. fscache super cookie relies on this for aux
data. So we need to push the fscache initialization to this
later point during mount.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Fix missed refcounting of IPC tcon used for getting domain-based DFS
root referrals. We want to keep it alive as long as mount is active
and can be refreshed. For standalone DFS root referrals it wouldn't
be a problem as the client ends up having an IPC tcon for both mount
and cache.
Fixes: c88f7dcd6d ("cifs: support nested dfs links over reconnect")
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Enzo Matsumiya <ematsumiya@suse.de>
Signed-off-by: Steve French <stfrench@microsoft.com>
In the native case, PER_CPU_VAR(cpu_tss_rw + TSS_sp0) is the
trampoline stack. But XEN pv doesn't use trampoline stack, so
PER_CPU_VAR(cpu_tss_rw + TSS_sp0) is also the kernel stack.
In that case, source and destination stacks are identical, which means
that reusing swapgs_restore_regs_and_return_to_usermode() in XEN pv
would cause %rsp to move up to the top of the kernel stack and leave the
IRET frame below %rsp.
This is dangerous as it can be corrupted if #NMI / #MC hit as either of
these events occurring in the middle of the stack pushing would clobber
data on the (original) stack.
And, with XEN pv, swapgs_restore_regs_and_return_to_usermode() pushing
the IRET frame on to the original address is useless and error-prone
when there is any future attempt to modify the code.
[ bp: Massage commit message. ]
Fixes: 7f2590a110 ("x86/entry/64: Use a per-CPU trampoline stack for IDT entries")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lkml.kernel.org/r/20211126101209.8613-4-jiangshanlai@gmail.com
The commit
c758907004 ("x86/entry/64: Remove unneeded kernel CR3 switching")
removed a CR3 write in the faulting path of load_gs_index().
But the path's FENCE_SWAPGS_USER_ENTRY has no fence operation if PTI is
enabled, see spectre_v1_select_mitigation().
Rather, it depended on the serializing CR3 write of SWITCH_TO_KERNEL_CR3
and since it got removed, add a FENCE_SWAPGS_KERNEL_ENTRY call to make
sure speculation is blocked.
[ bp: Massage commit message and comment. ]
Fixes: c758907004 ("x86/entry/64: Remove unneeded kernel CR3 switching")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20211126101209.8613-3-jiangshanlai@gmail.com
Jann Horn points out that there is another possible race wrt Unix domain
socket garbage collection, somewhat reminiscent of the one fixed in
commit cbcf01128d ("af_unix: fix garbage collect vs MSG_PEEK").
See the extended comment about the garbage collection requirements added
to unix_peek_fds() by that commit for details.
The race comes from how we can locklessly look up a file descriptor just
as it is in the process of being closed, and with the right artificial
timing (Jann added a few strategic 'mdelay(500)' calls to do that), the
Unix domain socket garbage collector could see the reference count
decrement of the close() happen before fget() took its reference to the
file and the file was attached onto a new file descriptor.
This is all (intentionally) correct on the 'struct file *' side, with
RCU lookups and lockless reference counting very much part of the
design. Getting that reference count out of order isn't a problem per
se.
But the garbage collector can get confused by seeing this situation of
having seen a file not having any remaining external references and then
seeing it being attached to an fd.
In commit cbcf01128d ("af_unix: fix garbage collect vs MSG_PEEK") the
fix was to serialize the file descriptor install with the garbage
collector by taking and releasing the unix_gc_lock.
That's not really an option here, but since this all happens when we are
in the process of looking up a file descriptor, we can instead simply
just re-check that the file hasn't been closed in the meantime, and just
re-do the lookup if we raced with a concurrent close() of the same file
descriptor.
Reported-and-tested-by: Jann Horn <jannh@google.com>
Acked-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit
18ec54fdd6 ("x86/speculation: Prepare entry code for Spectre v1 swapgs mitigations")
added FENCE_SWAPGS_{KERNEL|USER}_ENTRY for conditional SWAPGS. In
paranoid_entry(), it uses only FENCE_SWAPGS_KERNEL_ENTRY for both
branches. This is because the fence is required for both cases since the
CR3 write is conditional even when PTI is enabled.
But
96b2371413 ("x86/entry/64: Switch CR3 before SWAPGS in paranoid entry")
changed the order of SWAPGS and the CR3 write. And it missed the needed
FENCE_SWAPGS_KERNEL_ENTRY for the user gsbase case.
Add it back by changing the branches so that FENCE_SWAPGS_KERNEL_ENTRY
can cover both branches.
[ bp: Massage, fix typos, remove obsolete comment while at it. ]
Fixes: 96b2371413 ("x86/entry/64: Switch CR3 before SWAPGS in paranoid entry")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20211126101209.8613-2-jiangshanlai@gmail.com
Merge DTPM fixes for 5.16-rc4.
* powercap:
powercap: DTPM: Drop unused local variable from init_dtpm()
powercap/drivers/dtpm: Disable DTPM at boot time
Properly type the operands being passed to __put_user()/__get_user().
Otherwise, these routines truncate data for dependent instructions
(e.g., INSW) and only read/write one byte.
This has been tested by sending a string with REP OUTSW to a port and
then reading it back in with REP INSW on the same port.
Previous behavior was to only send and receive the first char of the
size. For example, word operations for "abcd" would only read/write
"ac". With change, the full string is now written and read back.
Fixes: f980f9c31a (x86/sev-es: Compile early handler code into kernel image)
Signed-off-by: Michael Sterritt <sterritt@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Reviewed-by: Peter Gonda <pgonda@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Link: https://lkml.kernel.org/r/20211119232757.176201-1-sterritt@google.com
The dtpm_descr variable in init_dtpm() is not used after commit
f751db8ada ("powercap/drivers/dtpm: Disable DTPM at boot time"),
so drop it.
Fixes: f751db8ada ("powercap/drivers/dtpm: Disable DTPM at boot time")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are two error paths which accidentally return success instead of
a negative error code.
Fixes: bbd2190ce9 ("Altera TSE: Add main and header file for Altera Ethernet Driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of dma_set_coherent_mask() is not always 0.
To catch the exception in case that dma is not support the mask.
Fixes: 9d61d138ab ("net: broadcom: rename BCM4908 driver & update DT binding")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the selftest framework always treats it as *ok* even though
some of them are failed actually. That's because the script always
returns 0.
It supports PASS/FAIL/SKIP exit code now.
CC: Philip Li <philip.li@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Li Zhijian <zhijianx.li@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KCSAN reported a data-race [1] around tx_rebalance_counter
which can be accessed from different contexts, without
the protection of a lock/mutex.
[1]
BUG: KCSAN: data-race in bond_alb_init_slave / bond_alb_monitor
write to 0xffff888157e8ca24 of 4 bytes by task 7075 on cpu 0:
bond_alb_init_slave+0x713/0x860 drivers/net/bonding/bond_alb.c:1613
bond_enslave+0xd94/0x3010 drivers/net/bonding/bond_main.c:1949
do_set_master net/core/rtnetlink.c:2521 [inline]
__rtnl_newlink net/core/rtnetlink.c:3475 [inline]
rtnl_newlink+0x1298/0x13b0 net/core/rtnetlink.c:3506
rtnetlink_rcv_msg+0x745/0x7e0 net/core/rtnetlink.c:5571
netlink_rcv_skb+0x14e/0x250 net/netlink/af_netlink.c:2491
rtnetlink_rcv+0x18/0x20 net/core/rtnetlink.c:5589
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x5fc/0x6c0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x6e1/0x7d0 net/netlink/af_netlink.c:1916
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg net/socket.c:724 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2409
___sys_sendmsg net/socket.c:2463 [inline]
__sys_sendmsg+0x195/0x230 net/socket.c:2492
__do_sys_sendmsg net/socket.c:2501 [inline]
__se_sys_sendmsg net/socket.c:2499 [inline]
__x64_sys_sendmsg+0x42/0x50 net/socket.c:2499
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff888157e8ca24 of 4 bytes by task 1082 on cpu 1:
bond_alb_monitor+0x8f/0xc00 drivers/net/bonding/bond_alb.c:1511
process_one_work+0x3fc/0x980 kernel/workqueue.c:2298
worker_thread+0x616/0xa70 kernel/workqueue.c:2445
kthread+0x2c7/0x2e0 kernel/kthread.c:327
ret_from_fork+0x1f/0x30
value changed: 0x00000001 -> 0x00000064
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 1082 Comm: kworker/u4:3 Not tainted 5.16.0-rc3-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: bond1 bond_alb_monitor
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the SND_PCI_QUIRK(...) of the TongFang PHxTxX1 barebone. This
fixes the issue of sound not working after s3 suspend.
When waking up from s3 suspend the Coef 0x10 is set to 0x0220 instead of
0x0020. Setting the value manually makes the sound work again. This patch
does this automatically.
While being on it, I also fixed the comment formatting of the quirk and
shortened variable and function names.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Fixes: dd6dd6e3c7 ("ALSA: hda/realtek: Add quirk for TongFang PHxTxX1")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211202165010.876431-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 5fa6863ba6 ("spi: Check we have a spi_device_id for each DT
compatible") added a test to check that every SPI driver has a
spi_device_id for each DT compatiable string defined by the driver
and warns if the spi_device_id is missing. The spi_device_ids are
missing for the dataflash driver and the following warnings are now
seen.
WARNING KERN SPI driver mtd_dataflash has no spi_device_id for atmel,at45
WARNING KERN SPI driver mtd_dataflash has no spi_device_id for atmel,dataflash
Fix this by adding the necessary spi_device_ids.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211130112443.107730-1-jonathanh@nvidia.com
Under certain circumstances, the timing settings calculated by
the FSMC NAND controller driver were inaccurate.
These settings led to incorrect data reads or fallback to
timing mode 0 depending on the NAND chip used.
The timing computation did not take into account the following
constraint given in SPEAr3xx reference manual:
twait >= tCEA - (tset * TCLK) + TOUTDEL + TINDEL
Enhance the timings calculation by taking into account this
additional constraint.
This change has no impact on slow timing modes such as mode 0.
Indeed, on mode 0, computed values are the same with and
without the patch.
NANDs which previously stayed in mode 0 because of fallback to
mode 0 can now work at higher speeds and NANDs which were not
working at all because of the corrupted data work at high
speeds without troubles.
Overall improvement on a Micron/MT29F1G08 (flash_speed tool):
mode0 mode3
eraseblock write speed 3220 KiB/s 4511 KiB/s
eraseblock read speed 4491 KiB/s 7529 KiB/s
Fixes: d9fb079571 ("mtd: nand: fsmc: add support for SDR timings")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-5-herve.codina@bootlin.com
When the NV-DDR interface is not supported by the NAND chip,
the value of onfi->nvddr_timing_modes is 0. In this case,
the best_mode variable value in nand_choose_best_nvddr_timings()
is -1. The last for-loop is skipped and the function returns an
uninitialized value.
If this returned value is 0, the nand_choose_best_sdr_timings()
is not executed and no 'best timing' are set. This leads the host
controller and the NAND chip working at default mode 0 timing
even if a better timing can be used.
Fix this uninitialized returned value.
nand_choose_best_sdr_timings() is pretty similar to
nand_choose_best_nvddr_timings(). Even if onfi->sdr_timing_modes
should never be seen as 0, nand_choose_best_sdr_timings() returned
value is fixed.
Fixes: a9ecc8c814 ("mtd: rawnand: Choose the best timings, NV-DDR included")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-3-herve.codina@bootlin.com
There is a small window in time during resume where the hardware
flow control signal RTS can be asserted (which allows a sender to
resume sending data to the UART) but the baud rate has not yet
been restored. This will cause corrupted data and FRAMING, OVERRUN
and BREAK errors. This is happening because the MCTRL register is
shadowed in uart_port struct and is later used during resume to set
the MCTRL register during both serial8250_do_startup() and
uart_resume_port(). Unfortunately, serial8250_do_startup()
happens before the UART baud rate is restored. The fix is to clear
the shadowed mctrl value at the end of suspend and restore it at the
end of resume.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20211201201402.47446-1-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cdnsp_endpoint_init(), cdnsp_ring_alloc() is assigned to pep->ring
and there is a dereference of it in cdnsp_endpoint_init(), which could
lead to a NULL pointer dereference on failure of cdnsp_ring_alloc().
Fix this bug by adding a check of pep->ring.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_USB_CDNSP_GADGET=y show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@vger.kernel.org>
Acked-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130172700.206650-1-zhou1615@umn.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turns out some xHC controllers require all 64 bits in the CRCR register
to be written to execute a command abort.
The lower 32 bits containing the command abort bit is written first.
In case the command ring stops before we write the upper 32 bits then
hardware may use these upper bits to set the commnd ring dequeue pointer.
Solve this by making sure the upper 32 bits contain a valid command
ring dequeue pointer.
The original patch that only wrote the first 32 to stop the ring went
to stable, so this fix should go there as well.
Fixes: ff0e50d356 ("xhci: Fix command ring pointer corruption while aborting a command")
Cc: stable@vger.kernel.org
Tested-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211126122340.1193239-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qdiscs/fq_pie requires CONFIG_NET_SCH_FQ_PIE, otherwise tc will fail
to create a fq_pie qdisc.
It fixes following issue:
# not ok 57 83be - Create FQ-PIE with invalid number of flows
# Command exited with 2, expected 0
# Error: Specified qdisc not found.
Signed-off-by: Li Zhijian <zhijianx.li@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark the summary result as FAIL to prevent from confusing the selftest
framework if some of them are failed.
Previously, the selftest framework always treats it as *ok* even though
some of them are failed actually. That's because the script tdc.sh always
return 0.
# All test results:
#
# 1..97
# ok 1 83be - Create FQ-PIE with invalid number of flows
# ok 2 8b6e - Create RED with no flags
[...snip]
# ok 6 5f15 - Create RED with flags ECN, harddrop
# ok 7 53e8 - Create RED with flags ECN, nodrop
# ok 8 d091 - Fail to create RED with only nodrop flag
# ok 9 af8e - Create RED with flags ECN, nodrop, harddrop
# not ok 10 ce7d - Add mq Qdisc to multi-queue device (4 queues)
# Could not match regex pattern. Verify command output:
# qdisc mq 1: root
# qdisc fq_codel 0: parent 1:4 limit 10240p flows 1024 quantum 1514 target 5ms interval 100ms memory_limit 32Mb ecn drop_batch 64
# qdisc fq_codel 0: parent 1:3 limit 10240p flows 1024 quantum 1514 target 5ms interval 100ms memory_limit 32Mb ecn drop_batch 64
[...snip]
# ok 96 6979 - Change quantum of a strict ETS band
# ok 97 9a7d - Change ETS strict band without quantum
#
#
#
#
ok 1 selftests: tc-testing: tdc.sh <<< summary result
CC: Philip Li <philip.li@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Li Zhijian <zhijianx.li@intel.com>
Acked-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The trampoline_pgd only maps the 0xfffffff000000000-0xffffffffffffffff
range of kernel memory (with 4-level paging). This range contains the
kernel's text+data+bss mappings and the module mapping space but not the
direct mapping and the vmalloc area.
This is enough to get the application processors out of real-mode, but
for code that switches back to real-mode the trampoline_pgd is missing
important parts of the address space. For example, consider this code
from arch/x86/kernel/reboot.c, function machine_real_restart() for a
64-bit kernel:
#ifdef CONFIG_X86_32
load_cr3(initial_page_table);
#else
write_cr3(real_mode_header->trampoline_pgd);
/* Exiting long mode will fail if CR4.PCIDE is set. */
if (boot_cpu_has(X86_FEATURE_PCID))
cr4_clear_bits(X86_CR4_PCIDE);
#endif
/* Jump to the identity-mapped low memory code */
#ifdef CONFIG_X86_32
asm volatile("jmpl *%0" : :
"rm" (real_mode_header->machine_real_restart_asm),
"a" (type));
#else
asm volatile("ljmpl *%0" : :
"m" (real_mode_header->machine_real_restart_asm),
"D" (type));
#endif
The code switches to the trampoline_pgd, which unmaps the direct mapping
and also the kernel stack. The call to cr4_clear_bits() will find no
stack and crash the machine. The real_mode_header pointer below points
into the direct mapping, and dereferencing it also causes a crash.
The reason this does not crash always is only that kernel mappings are
global and the CR3 switch does not flush those mappings. But if theses
mappings are not in the TLB already, the above code will crash before it
can jump to the real-mode stub.
Extend the trampoline_pgd to contain all kernel mappings to prevent
these crashes and to make code which runs on this page-table more
robust.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20211202153226.22946-5-joro@8bytes.org
Boris reported that in one of his randconfig builds, objtool got
infinitely stuck. Turns out there's trivial list corruption in the
pv_ops tracking when a function is both in a static table and in a code
assignment.
Avoid re-adding function to the pv_ops[] lists when they're already on
it.
Fixes: db2b0c5d7b ("objtool: Support pv_opsindirect calls for noinstr")
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Link: https://lkml.kernel.org/r/20211202204534.GA16608@worktop.programming.kicks-ass.net
Currently rp_filter tests in fib_tests.sh:fib_rp_filter_test() are
failing. ping sockets are bound to dummy1 using the "-I" option
(SO_BINDTODEVICE), but socket lookup is failing when receiving ping
replies, since the routing table thinks they belong to dummy0.
For example, suppose ping is using a SOCK_RAW socket for ICMP messages.
When receiving ping replies, in __raw_v4_lookup(), sk->sk_bound_dev_if
is 3 (dummy1), but dif (skb_rtable(skb)->rt_iif) says 2 (dummy0), so the
raw_sk_bound_dev_eq() check fails. Similar things happen in
ping_lookup() for SOCK_DGRAM sockets.
These tests used to pass due to a bug [1] in iputils, where "ping -I"
actually did not bind ICMP message sockets to device. The bug has been
fixed by iputils commit f455fee41c07 ("ping: also bind the ICMP socket
to the specific device") in 2016, which is why our rp_filter tests
started to fail. See [2] .
Fixing the tests while keeping everything in one netns turns out to be
nontrivial. Rework the tests and build the following topology:
┌─────────────────────────────┐ ┌─────────────────────────────┐
│ network namespace 1 (ns1) │ │ network namespace 2 (ns2) │
│ │ │ │
│ ┌────┐ ┌─────┐ │ │ ┌─────┐ ┌────┐ │
│ │ lo │<───>│veth1│<────────┼────┼─>│veth2│<──────────>│ lo │ │
│ └────┘ ├─────┴──────┐ │ │ ├─────┴──────┐ └────┘ │
│ │192.0.2.1/24│ │ │ │192.0.2.1/24│ │
│ └────────────┘ │ │ └────────────┘ │
└─────────────────────────────┘ └─────────────────────────────┘
Consider sending an ICMP_ECHO packet A in ns2. Both source and
destination IP addresses are 192.0.2.1, and we use strict mode rp_filter
in both ns1 and ns2:
1. A is routed to lo since its destination IP address is one of ns2's
local addresses (veth2);
2. A is redirected from lo's egress to veth2's egress using mirred;
3. A arrives at veth1's ingress in ns1;
4. A is redirected from veth1's ingress to lo's ingress, again, using
mirred;
5. In __fib_validate_source(), fib_info_nh_uses_dev() returns false,
since A was received on lo, but reverse path lookup says veth1;
6. However A is not dropped since we have relaxed this check for lo in
commit 66f8209547 ("fib: relax source validation check for loopback
packets");
Making sure A is not dropped here in this corner case is the whole point
of having this test.
7. As A reaches the ICMP layer, an ICMP_ECHOREPLY packet, B, is
generated;
8. Similarly, B is redirected from lo's egress to veth1's egress (in
ns1), then redirected once again from veth2's ingress to lo's
ingress (in ns2), using mirred.
Also test "ping 127.0.0.1" from ns2. It does not trigger the relaxed
check in __fib_validate_source(), but just to make sure the topology
works with loopback addresses.
Tested with ping from iputils 20210722-41-gf9fb573:
$ ./fib_tests.sh -t rp_filter
IPv4 rp_filter tests
TEST: rp_filter passes local packets [ OK ]
TEST: rp_filter passes loopback packets [ OK ]
[1] https://github.com/iputils/iputils/issues/55
[2] f455fee41c
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes: adb701d6cf ("selftests: add a test case for rp_filter")
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Acked-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211201004720.6357-1-yepeilin.cs@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull drm fixes from Dave Airlie:
"Bit of an uptick in patch count this week, though it's all relatively
small overall.
I suspect msm has been queuing up a few fixes to skew it here.
Otherwise amdgpu has a scattered bunch of small fixes, and then some
vc4, i915.
virtio-gpu changes an rc1 introduced uAPI mistake, and makes it
operate more like other drivers. This should be fine as no userspace
relies on the behaviour yet.
Summary:
dma-buf:
- memory leak fix
msm:
- kasan found memory overwrite
- mmap flags
- fencing error bug
- ioctl NULL ptr
- uninit var
- devfreqless devices fix
- dsi lanes fix
- dp: avoid unpowered aux xfers
amdgpu:
- IP discovery based enumeration fixes
- vkms fixes
- DSC fixes for DP MST
- Audio fix for hotplug with tiled displays
- Misc display fixes
- DP tunneling fix
- DP fix
- Aldebaran fix
amdkfd:
- Locking fix
- Static checker fix
- Fix double free
i915:
- backlight regression
- Intel HDR backlight detection fix
- revert TGL workaround that caused hangs
virtio-gpu:
- switch back to drm_poll
vc4:
- memory leak
- error check fix
- HVS modesetting fixes"
* tag 'drm-fixes-2021-12-03-1' of git://anongit.freedesktop.org/drm/drm: (41 commits)
Revert "drm/i915: Implement Wa_1508744258"
drm/amdkfd: process_info lock not needed for svm
drm/amdgpu: adjust the kfd reset sequence in reset sriov function
drm/amd/display: add connector type check for CRC source set
drm/amdkfd: fix double free mem structure
drm/amdkfd: set "r = 0" explicitly before goto
drm/amd/display: Add work around for tunneled MST.
drm/amd/display: Fix for the no Audio bug with Tiled Displays
drm/amd/display: Clear DPCD lane settings after repeater training
drm/amd/display: Allow DSC on supported MST branch devices
drm/amdgpu: Don't halt RLC on GFX suspend
drm/amdgpu: fix the missed handling for SDMA2 and SDMA3
drm/amdgpu: check atomic flag to differeniate with legacy path
drm/amdgpu: cancel the correct hrtimer on exit
drm/amdgpu/sriov/vcn: add new vcn ip revision check case for SIENNA_CICHLID
drm/i915/dp: Perform 30ms delay after source OUI write
dma-buf: system_heap: Use 'for_each_sgtable_sg' in pages free flow
drm/i915: Add support for panels with VESA backlights with PWM enable/disable
drm/vc4: kms: Fix previous HVS commit wait
drm/vc4: kms: Don't duplicate pending commit
...
Kumar Kartikeya says:
====================
This set includes fixes for two regressions and one build warning introduced by
the kfunc for modules series.
Changelog:
----------
v1 -> v2:
v1: https://lore.kernel.org/bpf/20211115191840.496263-1-memxor@gmail.com
* Instead of demoting resolve_btfids warning to debug, only skip in case of
set->cnt == 0.
====================
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
resolve_btfids prints a warning when it finds an unresolved symbol,
(id == 0) in id_patch. This can be the case for BTF sets that are empty
(due to disabled config options), hence printing warnings for certain
builds, most recently seen in [0].
The reason behind this is because id->cnt aliases id->id in btf_id
struct, leading to empty set showing up as ID 0 when we get to id_patch,
which triggers the warning. Since sets are an exception here, accomodate
by reusing hole in btf_id for bool is_set member, setting it to true for
BTF set when setting id->cnt, and use that to skip extraneous warning.
[0]: https://lore.kernel.org/all/1b99ae14-abb4-d18f-cc6a-d7e523b25542@gmail.com
Before:
; ./tools/bpf/resolve_btfids/resolve_btfids -v -b vmlinux net/ipv4/tcp_cubic.ko
adding symbol tcp_cubic_kfunc_ids
WARN: resolve_btfids: unresolved symbol tcp_cubic_kfunc_ids
patching addr 0: ID 0 [tcp_cubic_kfunc_ids]
sorting addr 4: cnt 0 [tcp_cubic_kfunc_ids]
update ok for net/ipv4/tcp_cubic.ko
After:
; ./tools/bpf/resolve_btfids/resolve_btfids -v -b vmlinux net/ipv4/tcp_cubic.ko
adding symbol tcp_cubic_kfunc_ids
patching addr 0: ID 0 [tcp_cubic_kfunc_ids]
sorting addr 4: cnt 0 [tcp_cubic_kfunc_ids]
update ok for net/ipv4/tcp_cubic.ko
Fixes: 0e32dfc80b ("bpf: Enable TCP congestion control kfunc from modules")
Reported-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20211122144742.477787-4-memxor@gmail.com
