In preparation for exporting an API to register Intel Vendor Specific
Extended Capabilities (VSEC) from other drivers, remove the pointer to
platform_info from intel_vsec_device. This prevents a potential page fault
when auxiliary drivers probe and attempt to dereference this pointer to
access the needed quirks field. Instead, just add the quirks to
intel_vsec_device.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20231129222132.2331261-5-david.e.box@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit 936874b77d ("platform/x86/intel/vsec: Add PCI error recovery
support to Intel PMT") added an xarray to track the list of vsec devices to
be recovered after a PCI error. But it did not provide cleanup for the list
leading to a memory leak that was caught by kmemleak. Do xa_alloc() before
devm_add_action_or_reset() so that the list may be cleaned up with
xa_erase() in the release function.
Fixes: 936874b77d ("platform/x86/intel/vsec: Add PCI error recovery support to Intel PMT")
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20231129222132.2331261-2-david.e.box@linux.intel.com
[hdegoede@redhat.com: Add missing xa_erase() on error-exit
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The secure boot state of the BlueField SoC is represented by two bits:
0 = production state
1 = secure boot enabled
2 = non-secure (secure boot disabled)
3 = RMA state
There is also a single bit to indicate whether production keys or
development keys are being used when secure boot is enabled.
This single bit (specified by MLXBF_BOOTCTL_SB_DEV_MASK) only has
meaning if secure boot state equals 1 (secure boot enabled).
The secure boot states are as follows:
- “GA secured” is when secure boot is enabled with official production keys.
- “Secured (development)” is when secure boot is enabled with development keys.
Without this fix “GA Secured” is displayed on development cards which is
misleading. This patch updates the logic in "lifecycle_state_show()" to
handle the case where the SoC is configured for secure boot and is using
development keys.
Fixes: 79e29cb8fb ("platform/mellanox: Add bootctl driver for Mellanox BlueField Soc")
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/20231130183515.17214-1-davthompson@nvidia.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
"select ACPI_VIDEO" cause recursive dependency when "depends on HWMON"
is added:
drivers/hwmon/Kconfig:6:error: recursive dependency detected!
drivers/hwmon/Kconfig:6: symbol HWMON is selected by EEEPC_LAPTOP
drivers/platform/x86/Kconfig:326: symbol EEEPC_LAPTOP depends on ACPI_VIDEO
drivers/acpi/Kconfig:208: symbol ACPI_VIDEO is selected by ACER_WMI
drivers/platform/x86/Kconfig:173: symbol ACER_WMI depends on HWMON
Replace the select with depends on to avoid this problem when the next
patch in this series adds "depends on HWMON".
There is a stub defined for the used acpi_video_get_backlight_type()
function when ACPI_VIDEO is not set, so use:
depends on ACPI_VIDEO || ACPI_VIDEO = n
Signed-off-by: SungHwan Jung <onenowy@gmail.com>
Link: https://lore.kernel.org/r/20231124094122.100707-4-onenowy@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Acer Predator PHN16-71 has the mode key that is used to rotate thermal
modes or toggle turbo mode with predator sense app (ver. 4) on windows.
This patch includes platform profile and the mode key support for the
device and also includes a small fix for "WMI_gaming_execute_u64"
function.
Signed-off-by: SungHwan Jung <onenowy@gmail.com>
Link: https://lore.kernel.org/r/20231124094122.100707-2-onenowy@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231112000029.151117-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ASUS have worked around an issue in XInput where it doesn't support USB
selective suspend, which causes suspend issues in Windows. They worked
around this by adjusting the MCU firmware to disable the USB0 hub when
the screen is switched off during the Microsoft DSM suspend path in ACPI.
The issue we have with this however is one of timing - the call the tells
the MCU to this isn't able to complete before suspend is done so we call
this in a prepare() and add a small msleep() to ensure it is done. This
must be done before the screen is switched off to prevent a variety of
possible races.
Further to this the MCU powersave option must also be disabled as it can
cause a number of issues such as:
- unreliable resume connection of N-Key
- complete loss of N-Key if the power is plugged in while suspended
Disabling the powersave option prevents this.
Without this the MCU is unable to initialise itself correctly on resume.
Signed-off-by: "Luke D. Jones" <luke@ljones.dev>
Tested-by: Philip Mueller <philm@manjaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231126230521.125708-2-luke@ljones.dev
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Change asus_q500a_i8042_filter() into a generic i8042-filter,
using a new filter_i8042_e1_extended_codes flag in the quirks struct
to decide if e1 extended codes should be filtered out or not.
This is a preparation patch for adding support for filtering volume key
events being reported twice through both the PS/2 keyboard and asus-wmi.
Note while modifying the code also drop the unnecessary unlikely()
annotations, this is not in a hot path so those are not necessary.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231120154235.610808-3-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The debugfs_create_blob() function has been used to create read-only binary
blobs in debugfs. The function filters out permissions, other than S_IRUSR,
S_IRGRP and S_IROTH, provided while creating the blobs.
The very behavior though is being changed through previous patch in the
series (fs: debugfs: Add write functionality to debugfs blobs) which makes
the binary blobs writable by owners. Thus, all permissions provided while
creating the blobs, except S_IRUSR,S_IWUSR, S_IRGRP, S_IROTH, will be
filtered by debugfs_create_blob().
As such, rectify the permissions of panicinfo file since the S_IFREG flag
was anyways being filtered out by debugfs_create_blob(). Moreover, the
very flag will always be set be set for the panicinfo file through
__debugfs_create_file().
Signed-off-by: Avadhut Naik <Avadhut.Naik@amd.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix the maximum brightness being much too low on the Yoga Tab 3 Pro.
The LP8557 backlight controller can either be configured to multiply its
PWM input and the I2C register set level (requiring both to be at 100%
for 100% output); or to only take the I2C register set level into account.
Multiplying the 2 levels is useful because this will turn off the backlight
when the panel goes off and turns off its PWM output.
But on the YT3-X90F the panel's PWM output defaults to a duty-cycle of much
less then 100%, severely limiting max brightness. In this case the LP8557
should be configured to only take the I2C register into account and
the i915 driver must turn off the backlight separately using a VBT MIPI
sequence to turn off the backlight.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231104205828.63139-4-hdegoede@redhat.com
Currently, WMI drivers have to use the deprecated GUID-based
interface when setting data blocks. This prevents those
drivers from fully moving away from this interface.
Provide wmidev_block_set() so drivers using wmi_set_block() can
fully migrate to the modern bus-based interface.
Tested with a custom SSDT from the Intel Slim Bootloader project.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20231103182526.3524-1-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
amd_pmc_get_dram_size() is used to get the DRAM size information. But
in the current code, mailbox command to get the DRAM size info is sent
based on the values of dev->major and dev->minor.
But dev->major and dev->minor will have either junk or zero assigned to
them until at least once a call to amd_pmc_get_smu_version() is made
which ideally populates dev->major and dev->minor.
However, adding a amd_pmc_get_smu_version() call to
amd_pmc_get_dram_size() has a downside of elevating the boot times.
After talking to the PMFW team, it's understood that the "get dram
size" mbox command would only be supported on specific platforms (like
Mendocino) and not all. So, adjust getting DRAM size behavior such
that,
- if running on Rembrandt or Mendocino and the underlying PMFW knows
how to execute the "get dram size" command it shall give the custom
dram size.
- if the underlying FW does not report the dram size, we just proceed
further and assign the default dram size.
The simplest way to address this is to remove amd_pmc_get_dram_size()
function and directly call the "get dram size" command in the
amd_pmc_s2d_init().
Reported-by: Mark Hasemeyer <markhas@chromium.org>
Fixes: be8325fb3d ("platform/x86/amd: pmc: Get STB DRAM size from PMFW")
Cc: stable@vger.kernel.org
Suggested-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20231116170121.3372222-1-Shyam-sundar.S-k@amd.com
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
'attr_name_kobj' is allocated using kzalloc, but on all the error paths
it is not freed, hence we have a memory leak.
Fix the error path before kobject_init_and_add() by adding kfree().
kobject_put() must be always called after passing the object to
kobject_init_and_add(). Only the error path which is immediately next
to kobject_init_and_add() calls kobject_put() and not any other error
path after it.
Fix the error handling after kobject_init_and_add() by moving the
kobject_put() into the goto label err_other_attr_init that is already
used by all the error paths after kobject_init_and_add().
Fixes: a34fc329b1 ("platform/x86: hp-bioscfg: bioscfg")
Cc: stable@vger.kernel.org # 6.6.x: c5dbf04160: platform/x86: hp-bioscfg: Simplify return check in hp_add_other_attributes()
Cc: stable@vger.kernel.org # 6.6.x: 5736aa9537: platform/x86: hp-bioscfg: move mutex_lock() down in hp_add_other_attributes()
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202309201412.on0VXJGo-lkp@intel.com/
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
[ij: Added the stable dep tags]
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20231113200742.3593548-3-harshit.m.mogalapalli@oracle.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The cros_ec_sensor_ring_median function currently uses an inefficient
sorting algorithm (> O(n)) to find the median of an array. This patch
replaces the sorting approach with the quickselect algorithm, which
achieves an average time complexity of O(n).
The algorithm employs the median-of-three rule to select the pivot,
mitigating worst-case scenarios and reducing the expected number of
necessary comparisons. This strategy enhances the algorithm's
efficiency and ensures a more balanced partitioning.
In the worst case, the runtime of quickselect could regress to O(n^2).
To address this, alternative algorithms like median-of-medians that
can guarantee O(n) even in the worst case. However, due to higher
overhead and increased complexity of implementation, quickselect
remains a pragmatic choice for our use case.
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Link: https://lore.kernel.org/r/20231110165314.1559285-1-visitorckw@gmail.com
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Pull x86 microcode loading updates from Borislac Petkov:
"Major microcode loader restructuring, cleanup and improvements by
Thomas Gleixner:
- Restructure the code needed for it and add a temporary initrd
mapping on 32-bit so that the loader can access the microcode
blobs. This in itself is a preparation for the next major
improvement:
- Do not load microcode on 32-bit before paging has been enabled.
Handling this has caused an endless stream of headaches, issues,
ugly code and unnecessary hacks in the past. And there really
wasn't any sensible reason to do that in the first place. So switch
the 32-bit loading to happen after paging has been enabled and turn
the loader code "real purrty" again
- Drop mixed microcode steppings loading on Intel - there, a single
patch loaded on the whole system is sufficient
- Rework late loading to track which CPUs have updated microcode
successfully and which haven't, act accordingly
- Move late microcode loading on Intel in NMI context in order to
guarantee concurrent loading on all threads
- Make the late loading CPU-hotplug-safe and have the offlined
threads be woken up for the purpose of the update
- Add support for a minimum revision which determines whether late
microcode loading is safe on a machine and the microcode does not
change software visible features which the machine cannot use
anyway since feature detection has happened already. Roughly, the
minimum revision is the smallest revision number which must be
loaded currently on the system so that late updates can be allowed
- Other nice leanups, fixess, etc all over the place"
* tag 'x86_microcode_for_v6.7_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
x86/microcode/intel: Add a minimum required revision for late loading
x86/microcode: Prepare for minimal revision check
x86/microcode: Handle "offline" CPUs correctly
x86/apic: Provide apic_force_nmi_on_cpu()
x86/microcode: Protect against instrumentation
x86/microcode: Rendezvous and load in NMI
x86/microcode: Replace the all-in-one rendevous handler
x86/microcode: Provide new control functions
x86/microcode: Add per CPU control field
x86/microcode: Add per CPU result state
x86/microcode: Sanitize __wait_for_cpus()
x86/microcode: Clarify the late load logic
x86/microcode: Handle "nosmt" correctly
x86/microcode: Clean up mc_cpu_down_prep()
x86/microcode: Get rid of the schedule work indirection
x86/microcode: Mop up early loading leftovers
x86/microcode/amd: Use cached microcode for AP load
x86/microcode/amd: Cache builtin/initrd microcode early
x86/microcode/amd: Cache builtin microcode too
x86/microcode/amd: Use correct per CPU ucode_cpu_info
...
