Pull IIO updaate from Jonathan:
IIO: 1st set of new device support, features and cleanup for 6.14
Fairly quiet cycle. Usual mix of new drivers, device support in
existing drivers, features and more general rework and cleanup.
There are a few late breaking or long standing but complex fixes
in here as well.
There is one expected merge conflict due to an upstream fix touching
neighboring code in ti-ads1119. The trivial resolution is the right one with
the result ending up as:
struct {
s16 sample;
aligned_s64 timestamp;
} scan;
New device support
==================
adi,ad4000
- Add support for many Pulsar ADC devices: AD7685, AD7686, AD7687, AD7688,
AD7690, AD7691, AD7693, AD7942, AD7946, AD7980, AD7982, AD7983, AD7984,
AD7988-1 and AD7988-5 ADCs. Generally similar to the AD4000 series
but with lower sampling rates and no configuration registers.
Includes addition of timestamp channels.
adi,adis16480
- Add support for ADIS16486, ADIS16487 and ADIS16489 IMUs. Required a few tweaks
to existing driver and addition of tables.
kionix,kx022a
- Add support for KX134ACR-LBZ accelerometer that is similar to the
KX132ACR-LBZ but with a wider (+-64G) sensor range.
- Add support for KX134-1211 accelerometer that is similar to the
KX132-1211 but with a wider (+-16G) sensor range.
nxp,fxls8962af
- Add support for fxls8974cf and fxls8967af accelerometers, Both are
compatible with fxls8962af but with different device IDs which are used in
presence checks.
renesas,rzg2l
- Add support for Renesas RZ/GS3 SoC ADCs (various driver refactors
precede this to allow for chip differences).
rohm,bd79704
- New driver for this 6 channel DAC.
st,mpu6050
- Support he IAM20380 which is effectively a cut down IAM20608 IMU with only
a gyroscope (no accelerometer).
st,stm-timmer-trigger
- Add support for ADC trigger use case for the STM32MP25 SOC. Do not support
the counter functionality in this driver as that is handled by the
counter subsystem.
ti,opt4060
- New driver for this RGBW color sensor.
Driver drop
===========
rohm,bu20008
- Drop as decision was made to not mass produce this light sensor after
Matti had done all the work to get a driver upstream.
Features
========
adi,ad_sigma_delta library + ad7124
- Allow for GPIO to check interrupt status, enabling this device on
more platforms that don't obey prior (non general) assumptions on
how the interrupt chips work.
- Allow variation in reset sequence length allowing chip specific
optimizations rather than always using worst case.
adi,ad7124
- Add temperature channel support.
adi,ad7173
- Add support calibration modes for this family of ADCs.
adi,adxl345
- Binding update to allow specification of which interrupt line is
connected (or none).
- Support interrupts and FIFO based data capture.
bosch,bme680
- Add regulators support. Note this required a new binding doc rather than
use of trivial-devices
- Runtime PM support.
microchip,pac1921
- Add ACPI support including _DSM for shunt value and label.
renesas,rzg2l
- Enable runtime autosuspend.
- Add suspend and resume support.
tyhx,hx9023s
- Add loading of a firmware file used to set defaults for some
configuration registers.
vishay,veml6030
- Support triggered buffers allowing efficient data capture at
higher speeds.
- Add regmap cache to reduce access to device.
Cleanup and minor fixes
=======================
cross-tree
- Another batch of conversions to devm_regulator_get_enable_read_voltage()
helper and related conversions to full devm that this enables.
- Various patches using guard() to allow early returns and simpler
code flow.
- Various conversions from s64 timestamp __aligned(8) to aligned_s64 type.
Includes a few cleanups where this unsigned and it should have been
signed.
- Fix up some missing types for drive-open-drain in dt-binding docs.
core
- Add missing documentation for iio_dmaengine_buffer_setup_ext()
- Add check that all buffers passed to iio_read_channel_ext_info()
and iio_read_channel_label() are page sized and page aligned.
Done this way because the callbacks are almost always only used
to fill sysfs attributes. The check covers the tiny percentage
of cases where use is made of this data in a consumer driver.
- Mark scan_timestamp memory of struct iio_dev private ensuring no
drivers change the value which belongs to the IIO core.
documentation
- Various missing ABI docs added.
- ABI docs made to use Y consistently as the wildcard for channel
number.
- Combine duplicate in_currentY_raw entries in ABI docs.
iio-mux
- Fix alignment of buffers passed to iio_channel_read_ext_info().
adi,ad_sigma_delta library
- Respect keep_cs_asserted flag in read path.
- Close a race condition around irq enabling and disabling.
- Use explicit unsigned int in place of unsigned.
adi,ad6695
- Move dt-binding header under adc sub-directory and fix include path in dt
example.
adi,ad7124
- Check number of channels in DT doesn't exceed what the driver can handle.
- Check input specified in DT are possible.
- Improved error reporting during probe.
adi,ad7173
- Drop unused structure element.
adi,ad7293
- Ensure power is turned on before resetting.
adi,adxl345
- Some documentation simplification and parameter renames.
- Add a function than unifies handling of power up and power down.
- Add defines to have a complete set of registers defined.
- Add missing \n to end of error messages.
amlogic,meson_saradc
- Simplify handling of the REG11 register access.
awinic,aw96104
- Constify iio_info structure.
bosch,bmp085
- Add to dt-binding to indicate devices support SPI.
bosch,bmp280
- Use sizeof() to replace a somewhat magic 2.
- Rename sleep related variables so the unit is included and use
fsleep() to replace usleep_range() calls.
bosch,bno055
- Constify struct bin_attribute
capella,cm3232
- Reset device before checking hardware ID inline with suggested flow
from datasheet.
diolan,dln2
- Simplify zeroing of structure used to gather up data by just
clearing the whole thing before writing rather than trying to
clear out he padding after write.
freescale,vf610
- Use devm_ and dev_error_probe() to simplify code and allow dropping
of explicit remove() callback.
invensense,timestamp library
- Use a cast to remove possibility of integer overflow.
kionix,kx022a
- Increase reset delay a little.
maxim,max1363
- Use a buffer of sufficient size in iio_priv() rather than allocating
variable sized buffer at use time.
microchip,mcp4725
- Replace of_property_read_bool() with of_property_present() for
detecting presence of regulator which is obviously not a bool.
nxp,fxls8962af
- Add wakeup-source property to the dt binding to allow these sensors
to wake the system up from suspend.
- Enable finer grained build when not all bus types need to be supported.
renesas,rzg2l
- Use dev_err_probe(), improving handling of probe errors and simplifying
code.
- Convert to devm_ based cleanup.
- Remove unnecessary runtime PM complexity as clocks are managed through
PM domains.
- Switch pm_ptr() removing need for __maybe_unused markings.
- use read_poll_timeout() to replace open coded equivalent.
samsung, ssp_sensors
- Simplify code by always providing timestamp whether or not it
is enabled.
st,lsm6dsx
- Avoid need to include linux/i3c/master by using i3cdev_to_dev() to
get to the contained struct device.
st,stm32-timer-trigger
- Check for clk_enable() fails.
vishay,veml6030
- Use new gts-helper functions and fix the _scale attribute to take into
account changes in gain and integration time.
Various other typo fixes in variable names + documentation and help text.
A few whitespace cleanup patches.
* tag 'iio-for-6.14a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (142 commits)
iio: iio-mux: kzalloc instead of devm_kzalloc to ensure page alignment
iio: adc: ad7625: Add ending newlines to error messages
iio: accel: adxl345: complete the list of defines
iio: accel: adxl345: add FIFO with watermark events
iio: accel: adxl345: initialize FIFO delay value for SPI
iio: accel: adxl345: introduce interrupt handling
iio: light: veml3235: fix scale to conform to ABI
iio: gts-helper: add helpers to ease searches of gain_sel and new_gain
iio: light: veml3235: extend regmap to add cache
iio: light: veml3235: fix code style
dt-bindings: iio: accel: adxl345: add interrupt-names
dt-bindings: iio: accel: adxl345: make interrupts not a required property
dt-bindings: iio: imu: bmi323: add boolean type for drive-open-drain
dt-bindings: iio: imu: bmi270: add boolean type for drive-open-drain
dt-bindings: iio: imu: bmi160: add boolean type for drive-open-drain
iio: adc: meson: simplify MESON_SAR_ADC_REG11 register access
iio: adc: meson: use tabs instead of spaces for some REG11 bit fields
iio: adc: meson: fix voltage reference selection field name typo
iio: adc: rockchip: correct alignment of timestamp
iio: imu: inv_icm42600: switch timestamp type from int64_t __aligned(8) to aligned_s64
...
Pull misc fixes from Andrew Morton:
"24 hotfixes. 17 are cc:stable. 15 are MM and 9 are non-MM.
The usual bunch of singletons - please see the relevant changelogs for
details"
* tag 'mm-hotfixes-stable-2024-12-07-22-39' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (24 commits)
iio: magnetometer: yas530: use signed integer type for clamp limits
sched/numa: fix memory leak due to the overwritten vma->numab_state
mm/damon: fix order of arguments in damos_before_apply tracepoint
lib: stackinit: hide never-taken branch from compiler
mm/filemap: don't call folio_test_locked() without a reference in next_uptodate_folio()
scatterlist: fix incorrect func name in kernel-doc
mm: correct typo in MMAP_STATE() macro
mm: respect mmap hint address when aligning for THP
mm: memcg: declare do_memsw_account inline
mm/codetag: swap tags when migrate pages
ocfs2: update seq_file index in ocfs2_dlm_seq_next
stackdepot: fix stack_depot_save_flags() in NMI context
mm: open-code page_folio() in dump_page()
mm: open-code PageTail in folio_flags() and const_folio_flags()
mm: fix vrealloc()'s KASAN poisoning logic
Revert "readahead: properly shorten readahead when falling back to do_page_cache_ra()"
selftests/damon: add _damon_sysfs.py to TEST_FILES
selftest: hugetlb_dio: fix test naming
ocfs2: free inode when ocfs2_get_init_inode() fails
nilfs2: fix potential out-of-bounds memory access in nilfs_find_entry()
...
In the function yas537_measure() there is a clamp_val() with limits of
-BIT(13) and BIT(13) - 1. The input clamp value h[] is of type s32. The
BIT() is of type unsigned long integer due to its define in
include/vdso/bits.h. The lower limit -BIT(13) is recognized as -8192 but
expressed as an unsigned long integer. The size of an unsigned long
integer differs between 32-bit and 64-bit architectures. Converting this
to type s32 may lead to undesired behavior.
Additionally, in the calculation lines h[0], h[1] and h[2] the unsigned
long integer divisor BIT(13) causes an unsigned division, shifting the
left-hand side of the equation back and forth, possibly ending up in large
positive values instead of negative values on 32-bit architectures.
To solve those two issues, declare a signed integer with a value of
BIT(13).
There is another omission in the clamp line: clamp_val() returns a value
and it's going nowhere here. Self-assign it to h[i] to make use of the
clamp macro.
Finally, replace clamp_val() macro by clamp() because after changing the
limits from type unsigned long integer to signed integer it's fine that
way.
Link: https://lkml.kernel.org/r/11609b2243c295d65ab4d47e78c239d61ad6be75.1732914810.git.jahau@rocketmail.com
Fixes: 65f79b5010 ("iio: magnetometer: yas530: Add YAS537 variant")
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202411230458.dhZwh3TT-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202411282222.oF0B4110-lkp@intel.com/
Reviewed-by: David Laight <david.laight@aculab.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Pull char/misc/IIO/whatever driver subsystem updates from Greg KH:
"Here is the 'big and hairy' char/misc/iio and other small driver
subsystem updates for 6.13-rc1.
Loads of things in here, and even a fun merge conflict!
- rust misc driver bindings and other rust changes to make misc
drivers actually possible.
I think this is the tipping point, expect to see way more rust
drivers going forward now that these bindings are present. Next
merge window hopefully we will have pci and platform drivers
working, which will fully enable almost all driver subsystems to
start accepting (or at least getting) rust drivers.
This is the end result of a lot of work from a lot of people,
congrats to all of them for getting this far, you've proved many of
us wrong in the best way possible, working code :)
- IIO driver updates, too many to list individually, that subsystem
keeps growing and growing...
- Interconnect driver updates
- nvmem driver updates
- pwm driver updates
- platform_driver::remove() fixups, loads of them
- counter driver updates
- misc driver updates (keba?)
- binder driver updates and fixes
- loads of other small char/misc/etc driver updates and additions,
full details in the shortlog.
All of these have been in linux-next for a while, with no other
reported issues other than that merge conflict"
* tag 'char-misc-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (401 commits)
mei: vsc: Fix typo "maintstepping" -> "mainstepping"
firmware: Switch back to struct platform_driver::remove()
misc: isl29020: Fix the wrong format specifier
scripts/tags.sh: Don't tag usages of DEFINE_MUTEX
fpga: Switch back to struct platform_driver::remove()
mei: vsc: Improve error logging in vsc_identify_silicon()
mei: vsc: Do not re-enable interrupt from vsc_tp_reset()
dt-bindings: spmi: qcom,x1e80100-spmi-pmic-arb: Add SAR2130P compatible
dt-bindings: spmi: spmi-mtk-pmif: Add compatible for MT8188
spmi: pmic-arb: fix return path in for_each_available_child_of_node()
iio: Move __private marking before struct element priv in struct iio_dev
docs: iio: ad7380: add adaq4370-4 and adaq4380-4
iio: adc: ad7380: add support for adaq4370-4 and adaq4380-4
iio: adc: ad7380: use local dev variable to shorten long lines
iio: adc: ad7380: fix oversampling formula
dt-bindings: iio: adc: ad7380: add adaq4370-4 and adaq4380-4 compatible parts
bus: mhi: host: pci_generic: Use pcim_iomap_region() to request and map MHI BAR
bus: mhi: host: Switch trace_mhi_gen_tre fields to native endian
misc: atmel-ssc: Use of_property_present() for non-boolean properties
misc: keba: Add hardware dependency
...
The Allegro MicroSystems ALS31300 is a 3-D Linear Hall Effect Sensor
mainly used for 3D head-on motion sensing applications.
The device is configured over I2C, and as part of the Sensor data the
temperature core is also provided.
While the device provides an IRQ gpio, it depends on a configuration
programmed into the internal EEPROM, thus only the default mode is
supported and buffered input via trigger is also supported to allow
streaming values with the same sensing timestamp.
The device can be configured with different sensitivities in factory,
but the sensitivity value used to calculate value into the Gauss
unit is not available from registers, thus the sensitivity is provided
by the compatible/device-id string which is based on the part number
as described in the datasheet page 2.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20241030-topic-input-upstream-als31300-v4-3-494297c9e50a@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jonathan writes:
IIO: 1st set of fixes for the 6.12 cycle.
Most of this pull request is the result of Javier Carrasco doing a
careful audit for missing Kconfig dependencies that luck has meant
the random builds have never hit. The rest is the usual mix of old
bugs that have surfaced and some fallout from the recent merge window.
adi,ad5686
- Fix binding duplication of compatible strings.
bosch,bma400
- Fix an uninitialized variable in the event tap handling.
bosch,bmi323
- Fix several issues in the register saving and restore on suspend/resume
sensiron,spd500
- Fix missing CRC8 dependency
ti,op3001
- Fix a missing full-scale range value (values above this point were
all reported wrongly)
vishay,veml6030
- Fix a segmentation fault due to some type confusion.
- Fix wrong ambient light sensor resolution.
* tag 'iio-fixes-for-6.12a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (34 commits)
iio: frequency: admv4420: fix missing select REMAP_SPI in Kconfig
iio: frequency: {admv4420,adrf6780}: format Kconfig entries
iio: adc: ad4695: Add missing Kconfig select
iio: adc: ti-ads8688: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: hid-sensors: Fix an error handling path in _hid_sensor_set_report_latency()
iioc: dac: ltc2664: Fix span variable usage in ltc2664_channel_config()
iio: dac: stm32-dac-core: add missing select REGMAP_MMIO in Kconfig
iio: dac: ltc1660: add missing select REGMAP_SPI in Kconfig
iio: dac: ad5770r: add missing select REGMAP_SPI in Kconfig
iio: amplifiers: ada4250: add missing select REGMAP_SPI in Kconfig
iio: frequency: adf4377: add missing select REMAP_SPI in Kconfig
iio: resolver: ad2s1210: add missing select (TRIGGERED_)BUFFER in Kconfig
iio: resolver: ad2s1210 add missing select REGMAP in Kconfig
iio: proximity: mb1232: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: pressure: bm1390: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: magnetometer: af8133j: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: light: bu27008: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: chemical: ens160: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: dac: ad5766: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: dac: ad3552r: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
...
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/iio/ to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
While touching these files, make indention of the struct initializer
consistent in several files.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20241009060056.502059-2-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Jonathan writes:
IIO: 1st set of new device support, features and cleanup for 6.9
IIO Backend support
===================
New approach from Nuno Sa to the problem of reuse of drivers with
IIO devices that are actually the combination of a highspeed chip
and an FPGA core handling the data capture and flows. It will hopefully
also apply to some other split designs. The ad9467 and axi-adi drivers
are converted over to this framework.
New device support
==================
adi,admfm2000
- New driver for this dual microwave down converter.
ams,as73211
- Add support for as7331 UV sensor.
richtek,rtq6056
- Add support for related parts RTQ6053 and RTQ6059
st,lsm6dsx
- Add ASM330LHHXG1 accelerometer and gyro support (mainly IDs)
ti,ads1298
- New driver for this medical ADC.
Features
========
tests
- Unit tests for the gain-time-scale helper library.
bosch,bmi088
- I2C support.
bosh,bmi160
- Add 10EC5280 ACPI ID. Used in a number of devices that won't get fixed.
The ID is actually a PCI ID belonging to realtech. No response was received
to earlier attempts to notify them of this.
The manufacturers of some devices have replied to say they will not fix
this incorrect ID. Add the ID and hope it isn't a problem.
bosch,bmi323
- Add BOSC0200 ACPI ID. Note this is a duplicate of one in the bmc150
driver (it appears these parts share a windows driver).
Both drivers perform an ID check that is safe on the other part before
successfully probing.
hid-sensors-als
- Add color temperature and chromaticity support. Note this is a replacement
for the series reverted in 6.8 that correctly handles all the potential
channel combinations.
honeywell,hsc030pa
- Triggered buffer support (after driver cleanup).
honeywell,mprls00025pa
- Improved error handling.
- New DT binding to allow use of part number triplet as provided in data sheet
to specify equivalent of most of the binding more efficiently.
- SPI support.
memsic,mxc4005
- ACPI ID MDA6655 as seen in the Chuwi Minibook X 2023
ti,hdc3020
- Add threshold event support (after some driver cleanup)
veml,vcnl4000
- Switch to high resolution proximity measurement.
Cleanup
=======
Various minor typo fixes and better use of defines etc.
Treewide
- Stop using ACPI_PTR(). The savings in space are small and not worth
the complexity of __maybe_unused of ifdef guards. To avoid use in
new IIO drivers based on copy and paste, clean it out.
- cleanup.h based handling of iio_device_claim_direct_mode()/
iio_device_release_direct_mode() using scope_cond_guard().
In many drivers this is combined with other automated cleanup
to give maximum simplifications.
An initial set of drivers are converted over to this infrastructure.
Tools
- Use rewinddir() instead of seekdir() to return to start of file.
core
- Make iio_bus_type constant.
adi,ad16475
- Use irq_get_trigger_type() instead of opencoding.
adi,ad16480
- Use irq_get_trigger_type() instead of opencoding.
adi,ad-sigma-delta
- Avoid overwriting IRQ flags if provided by firmware.
ams,as73211
- Use IIO_VAL_FRACTIONAL for scales to simplify the code and potentially
improve accuracy.
gts-library
- Use a div64_u64() instead of a loop to do a division.
honeywell,mprls00025pa
- Clean up dt-binding doc.
- Drop defaults when DT binding not providing values. Very unlikely
these were useful given they were wrong for vast majority of supported
devices.
- Whitespace cleanup
miramems,da280
- Use i2c_get_match_data() to replace hand rolled ACPI matching code.
semtech,sx9324
- Avoid unnecessary copying of property strings.
st,lsm6dsx
- Improve docs, particularly wrt to making addition of new device
support less noisy.
st,lsm9ds0
- Use dev_err_probe() in all probe() error handling.
- Improved header includes.
- Tidy up termination of ID tables.
ti,ads1014
- Correct upper bound on PGA (wrong value had no actual impact)
ti,afe4403/4404
- devm_ useage to simplify error handling in probe() and allow() remove to
be dropped.
voltage-divider
- Add dt-binding for io-channel-cells to allow such a device to be both
an IIO consumer and IIO producer at the same time.
* tag 'iio-for-6.9a' of http://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (106 commits)
iio: imu: bmi323: Add ACPI Match Table
iio: accel: bmc150: Document duplicate ACPI entries with bmi323 driver
iio: adc: ti-ads1298: Add driver
dt-bindings: iio: adc: ti-ads1298: Add bindings
iio: pressure: hsc030pa add triggered buffer
iio: pressure: hsc030pa add mandatory delay
iio: pressure: hsc030pa: update datasheet URLs
iio: pressure: hsc030pa: include cleanup
iio: pressure: hsc030pa: use signed type to hold div_64() result
dt-bindings: iio: pressure: honeywell,hsc030pa.yaml add spi props
iio: st_sensors: lsm9ds0: Use common style for terminator in ID tables
iio: st_sensors: lsm9ds0: Don't use "proxy" headers
iio: st_sensors: lsm9ds0: Use dev_err_probe() everywhere
iio: adc: adi-axi-adc: move to backend framework
iio: adc: ad9467: convert to backend framework
iio: add the IIO backend framework
iio: buffer-dmaengine: export buffer alloc and free functions
of: property: add device link support for io-backends
dt-bindings: adc: axi-adc: update bindings for backend framework
dt-bindings: adc: ad9467: add new io-backend property
...
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem changes
for 6.8-rc1.
Other than lots of binder driver changes (as you can see by the merge
conflicts) included in here are:
- lots of iio driver updates and additions
- spmi driver updates
- eeprom driver updates
- firmware driver updates
- ocxl driver updates
- mhi driver updates
- w1 driver updates
- nvmem driver updates
- coresight driver updates
- platform driver remove callback api changes
- tags.sh script updates
- bus_type constant marking cleanups
- lots of other small driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (341 commits)
android: removed duplicate linux/errno
uio: Fix use-after-free in uio_open
drivers: soc: xilinx: add check for platform
firmware: xilinx: Export function to use in other module
scripts/tags.sh: remove find_sources
scripts/tags.sh: use -n to test archinclude
scripts/tags.sh: add local annotation
scripts/tags.sh: use more portable -path instead of -wholename
scripts/tags.sh: Update comment (addition of gtags)
firmware: zynqmp: Convert to platform remove callback returning void
firmware: turris-mox-rwtm: Convert to platform remove callback returning void
firmware: stratix10-svc: Convert to platform remove callback returning void
firmware: stratix10-rsu: Convert to platform remove callback returning void
firmware: raspberrypi: Convert to platform remove callback returning void
firmware: qemu_fw_cfg: Convert to platform remove callback returning void
firmware: mtk-adsp-ipc: Convert to platform remove callback returning void
firmware: imx-dsp: Convert to platform remove callback returning void
firmware: coreboot_table: Convert to platform remove callback returning void
firmware: arm_scpi: Convert to platform remove callback returning void
firmware: arm_scmi: Convert to platform remove callback returning void
...
The current offset has the scale already applied to it. The ABI
documentation defines the offset parameter as "offset to be added
to <type>[Y]_raw prior to scaling by <type>[Y]_scale in order to
obtain value in the <type> units as specified in <type>[Y]_raw
documentation"
The right value is obtained at 0 degrees Celsius by the formula provided
in the datasheet:
T = Tsens_t0 + (Tadc_t - Tadc_t0) / Tadc_res
where:
T = 0 degrees Celsius
Tsens_t0 (reference temperature) = 25 degrees Celsius
Tadc_t0 (16-bit format for Tsens_t0) = 17508
Tadc_res = 60.1 LSB/degree Celsius
The resulting offset is 16005.5, which has been truncated to 16005 to
provide an integer value with a precision loss smaller than the 1-LSB
measurement precision.
Fix the offset to apply its value prior to scaling.
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/9879beec-05fc-4fc6-af62-d771e238954e@wolfvision.net
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-41-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jonathan writes:
1st set of IIO new device support, features and cleanup for the 6.5 cycle.
New device support
- honeywell,mprls0025pa
* New driver and dt-bindings for this series of pressure sensors.
- invensense,mpu6050
* Add support for ICM 20600 IMU (ID, bindings and device data).
- melexis,mlx90614
* Add support for mlx90615 Infra Red Thermometer after driver cleanup
and refactoring to support the differences in this device.
- renesas,x9250
* New driver and bindings for this quad potentiometer.
- rockchip,saradc
* Add support for RK3588. Also included is a bunch of refactoring and
cleanup for that driver.
- rohm,bu27008
* New driver bindings etc for this 5 photodiode color sensor.
- st,lsm9ds0/st,st-sensors
* ID added for LSM303D accelerometer and magnetometer including ACPI binding.
- ti,opt4001
* New driver and bindings for this ambient light sensor.
Features
- core
* Introduce iio_validate_own_trigger() for cases where a driver can only
consumer a trigger it registered (detected via same parent device).
Use it in the kionix,kx022a driver and new rohm,by27008 driver.
- dynaimage,al3320a
* ACPI binding CALS0001 seen on Lenovo Yoga Table 2 devices.
- kionix,kx002a
* Enable asynchronous probe.
- rohm,bu27034
* Enable asynchronous probe.
- ti,tmp006
* Explicit support for DT including binding documentation.
Cleanups, minor fixes and misc improvements.
- treewide
* Switch I2C drivers from probe_new() back to probe() - part of the
long process of getting rid of a parameter from probe()
* Various whitespace and typo fixes not otherwise called out.
- core
* industrialio-buffer,Style cleanup.
* Add documentation to extend_name field of struct iio_chan_spec to
direct people using it towards the label infrastructure instead.
extend_name was a design mistake a long time back so directly people
away from it may be useful.
- adi,ad7606
* Add HAS_IOPORT dependency to prepare for some Kconfig changes.
- bosch,bma400
* Drop pointless print of ret in a dev_err_probe() message.
- invensense,icm42600
* Rework timestamp handling to reduce jitter.
- mediatek,mt7986-auxdac
* Add DT binding for this part.
- qcom,spmi-vadc
* Allow for 1/16th prescaling used on a few devices.
* Various changes to channel labeling and naming, including dropping
use of fwnode_name which generates odd channel names. Small ABI
change as a result, but not thought to be a problem for users of this
platform.
- st,lsm6dsx
* dt-binding: Use common schema for mount-matrix via a reference.
- st,stm32
* Add a debug print for when legacy channel config is used.
- ti,palmas-adc
* Drop unused i2c.h include.
* tag 'iio-for-6.5a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (59 commits)
dt-bindings: iio: rockchip: Fix 'oneOf' condition failed warning
dt-bindings: iio: afe: voltage-divider: Spelling s/curcuit/circuit/
dt-bindings: iio: adc: Add rockchip,rk3588-saradc string
iio: adc: rockchip_saradc: Use dev_err_probe
iio: adc: rockchip_saradc: Match alignment with open parenthesis
iio: adc: rockchip_saradc: Use of_device_get_match_data
iio: adc: rockchip_saradc: Make use of devm_clk_get_enabled
iio: adc: rockchip_saradc: Add support for RK3588
iio: adc: rockchip_saradc: Add callback functions
iio: temperature: tmp006: Add OF device matching support
dt-bindings: iio: temperature: Add support for tmp006
staging: iio: Switch i2c drivers back to use .probe()
iio: amplifiers: ad8366 Fix whitespace issue
iio: imu: inv_icm42600: avoid frequent timestamp jitter
MAINTAINERS: Add ROHM BU27008
iio: light: ROHM BU27008 color sensor
iio: kx022a: Use new iio_validate_own_trigger()
iio: trigger: Add simple trigger_validation helper
dt-bindings: iio: light: ROHM BU27008
iio: mlx90614: Add MLX90615 support
...
