Merge from Jonathan:
IIO: 2nd set of fixes for the 6.13 cycle.
Given timing so late in cycle and that they are all confined to
specific drivers, it is fine for these to go upstream early in the
6.14 cycle.
hid-sensors
- Handle processed attention channel rather than just returning
an error.
adi,ad3552r
- Fix output ranges for ad3541r and ad3542r.
- Clear the reset status flag so that we can pick up any resets
during operation.
adi,ad5791
- Fix a misleading dt binding example where the sense of the
interrupt was reversed.
adi,ad7606
- Fix some hard coded offsets that should be taking the number of
channels on a particular part into account. These were missed
due to some racing changes.
ams,as73211
- Fix an off by one in optimized path for just reading the colour
channels.
bosch,bme680
- Fix type of variable passed as pointer, ensuring it works on
big endian systems and doesn't expose uninitialized data.
* tag 'iio-fixes-for-6.13b' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: dac: ad3552r-hs: clear reset status flag
iio: dac: ad3552r-common: fix ad3541/2r ranges
iio: chemical: bme680: Fix uninitialized variable in __bme680_read_raw()
iio: light: as73211: fix channel handling in only-color triggered buffer
dt-bindings: iio: dac: ad5791: ldac gpio is active low
iio: hid-sensor-prox: Fix invalid read_raw for attention
iio: adc: ad7606: Fix hardcoded offset in the ADC channels
Fix ad3541/2r voltage ranges to be as per ad3542r datasheet,
rev. C, table 38 (page 57).
The wrong ad354xr ranges was generating erroneous Vpp output.
In more details:
- fix wrong number of ranges, they are 5 ranges, not 6,
- remove non-existent 0-3V range,
- adjust order, since ad3552r_find_range() get a wrong index,
producing a wrong Vpp as output.
Retested all the ranges on real hardware, EVALAD3542RFMCZ:
adi,output-range-microvolt (fdt):
<(000000) (2500000)>; ok (Rfbx1, switch 10)
<(000000) (5000000)>; ok (Rfbx1, switch 10)
<(000000) (10000000)>; ok (Rfbx1, switch 10)
<(-5000000) (5000000)>; ok (Rfbx2, switch +/- 5)
<(-2500000) (7500000)>; ok (Rfbx2, switch -2.5/7.5)
Fixes: 8f2b54824b ("drivers:iio:dac: Add AD3552R driver support")
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250108-wip-bl-ad3552r-axi-v0-iio-testing-carlos-v2-1-2dac02f04638@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BD79703 is a 6 channel digital to analog converter.
Based on the data-sheet examples the hardware would support setting the
DAC word without changing the actual output. The data-sheet is not too
specific on how the enabling the output of new voltage set by DAC
should be done - hence this is not implemented by the driver.
The BD79703 would also support two specific "PULL_DOWN" modes. These
aren't currently supported by the driver either.
Add a very basic support for controlling the channel outputs one-by-one.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/bc77d7b979ca28408a216f597082fcd94ec63be7.1734608215.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simplify the code by using devm_regulator_get_enable_read_voltage().
There is a small change in behavior. Before, all errors from
devm_regulator_get_optional() were ignored and assumed to mean that
the external reference supply was absent. Now, only -ENODEV is checked
and other errors will cause a failure to probe. So now, this will
catch errors, like using the wrong data type for the devicetree
property.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20241120-iio-regulator-cleanup-round-6-v1-3-d5a5360f7ec3@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
write_event_config callback use an int for state, but it is actually a
boolean. iio_ev_state_store is actually using kstrtobool to check user
input, then gives the converted boolean value to write_event_config.
Fix signature and update all iio drivers to use the new signature.
This patch has been partially written using coccinelle with the
following script:
$ cat iio-bool.cocci
// Options: --all-includes
virtual patch
@c1@
identifier iioinfo;
identifier wecfunc;
@@
static const struct iio_info iioinfo = {
...,
.write_event_config =
(
wecfunc
|
&wecfunc
),
...,
};
@@
identifier c1.wecfunc;
identifier indio_dev, chan, type, dir, state;
@@
int wecfunc(struct iio_dev *indio_dev, const struct iio_chan_spec *chan, enum iio_event_type type, enum iio_event_direction dir,
-int
+bool
state) {
...
}
make coccicheck MODE=patch COCCI=iio-bool.cocci M=drivers/iio
Unfortunately, this script didn't match all files:
* all write_event_config callbacks using iio_device_claim_direct_scoped
were not detected and not patched.
* all files that do not assign and declare the write_event_config
callback in the same file.
iio.h was also manually updated.
The patch was build tested using allmodconfig config.
cc: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20241031-iio-fix-write-event-config-signature-v2-7-2bcacbb517a2@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add High Speed ad3552r platform driver.
The ad3552r DAC is controlled by a custom (fpga-based) DAC IP
through the current AXI backend, or similar alternative IIO backend.
Compared to the existing driver (ad3552r.c), that is a simple SPI
driver, this driver is coupled with a DAC IIO backend that finally
controls the ad3552r by a fpga-based "QSPI+DDR" interface, to reach
maximum transfer rate of 33MUPS using dma stream capabilities.
All commands involving QSPI bus read/write are delegated to the backend
through the provided APIs for bus read/write.
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20241028-wip-bl-ad3552r-axi-v0-iio-testing-v9-7-f6960b4f9719@kernel-space.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If REGMAP_SPI is n and LTC2664 is y, the following build error occurs:
riscv64-unknown-linux-gnu-ld: drivers/iio/dac/ltc2664.o: in function `ltc2664_probe':
ltc2664.c:(.text+0x714): undefined reference to `__devm_regmap_init_spi'
Select REGMAP_SPI instead of REGMAP for LTC2664 to fix it.
Fixes: 4cc2fc445d ("iio: dac: ltc2664: Add driver for LTC2664 and LTC2672")
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20241024015553.1111253-1-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jonathan writes:
IIO: 1st set of fixes for the 6.12 cycle.
Most of this pull request is the result of Javier Carrasco doing a
careful audit for missing Kconfig dependencies that luck has meant
the random builds have never hit. The rest is the usual mix of old
bugs that have surfaced and some fallout from the recent merge window.
adi,ad5686
- Fix binding duplication of compatible strings.
bosch,bma400
- Fix an uninitialized variable in the event tap handling.
bosch,bmi323
- Fix several issues in the register saving and restore on suspend/resume
sensiron,spd500
- Fix missing CRC8 dependency
ti,op3001
- Fix a missing full-scale range value (values above this point were
all reported wrongly)
vishay,veml6030
- Fix a segmentation fault due to some type confusion.
- Fix wrong ambient light sensor resolution.
* tag 'iio-fixes-for-6.12a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (34 commits)
iio: frequency: admv4420: fix missing select REMAP_SPI in Kconfig
iio: frequency: {admv4420,adrf6780}: format Kconfig entries
iio: adc: ad4695: Add missing Kconfig select
iio: adc: ti-ads8688: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: hid-sensors: Fix an error handling path in _hid_sensor_set_report_latency()
iioc: dac: ltc2664: Fix span variable usage in ltc2664_channel_config()
iio: dac: stm32-dac-core: add missing select REGMAP_MMIO in Kconfig
iio: dac: ltc1660: add missing select REGMAP_SPI in Kconfig
iio: dac: ad5770r: add missing select REGMAP_SPI in Kconfig
iio: amplifiers: ada4250: add missing select REGMAP_SPI in Kconfig
iio: frequency: adf4377: add missing select REMAP_SPI in Kconfig
iio: resolver: ad2s1210: add missing select (TRIGGERED_)BUFFER in Kconfig
iio: resolver: ad2s1210 add missing select REGMAP in Kconfig
iio: proximity: mb1232: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: pressure: bm1390: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: magnetometer: af8133j: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: light: bu27008: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: chemical: ens160: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: dac: ad5766: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: dac: ad3552r: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
...
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/iio/ to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
While touching these files, make indention of the struct initializer
consistent in several files.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20241009060056.502059-2-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
