Add initial support for the Texas Instruments TPS25990 eFuse.
This adds the basic PMBUS telemetry support for the device.
From Karol Przybylski:
The tps25990_read_word_data function contains a block of unreachable code
caused by the syntactic structure in the PMBUS_VIRT_READ_IIN_MAX case.
Specifically, the return TPS25990_READ_IIN_PEAK; statement immediately
exits the function, making the next lines unreachable.
This patch removes the return statement, leaving the expected handling.
Discovered in coverity: CID 1602227
Tested-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[groeck: Adjust to MODULE_IMPORT_NS API change]
[karprzy7@gmail.com: Fix unreachable code in tps25990_read_word_data]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add a module parameter to force the write protection mode of pmbus chips.
4 protections modes are provided to start with:
* 0: Remove the write protection
* 1: Disable all writes except to the WRITE_PROTECT, OPERATION,
PAGE, ON_OFF_CONFIG and VOUT_COMMAND commands
* 2: Disable all writes except to the WRITE_PROTECT, OPERATION and
PAGE commands
* 3: Disable all writes except to the WRITE_PROTECT command
Of course, if the parameter is not provided, the default write protection
status of the pmbus chips is left untouched.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writing PMBus protected registers does succeed from the smbus perspective,
even if the write is ignored by the device and a communication fault is
raised. This fault will silently be caught and cleared by pmbus irq if one
has been registered.
This means that the regulator call may return succeed although the
operation was ignored.
With this change, the operation which are not supported will be properly
flagged as such and the regulator framework won't even try to execute them.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[groeck: Adjust to EXPORT_SYMBOL_NS_GPL API change]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some applications require Vout to be higher than the detectable voltage
range of the Vsense pin for a given rail. In such applications, a voltage
divider may be placed between Vout and the Vsense pin, but this results
in erroneous telemetry being read back from the part. This change adds
support for a voltage divider to be defined in the devicetree for a (or
multiple) specific rail(s) for a supported digital multiphase device and
for the applicable Vout telemetry to be scaled based on the voltage
divider configuration.
This change copies the implementation of the vout-voltage-divider
devicetree property defined in the maxim,max20730 bindings schema since
it is the best fit for the use case of scaling hwmon PMBus telemetry. The
generic voltage-divider property used by many iio drivers was determined
to be a poor fit because that schema is tied directly to iio and the
isl68137 driver is not an iio driver.
Signed-off-by: Grant Peltier <grantpeltier93@gmail.com>
Message-ID: <8c2d048f87282bcf66313afbf5e923d8fc17b4d7.1731439797.git.grantpeltier93@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pmbus_write_smbalert_mask() ignores the errors if the chip can't set
smbalert mask the standard way. It is not necessarily a problem for the irq
support if the chip is otherwise properly setup but it may leave an
uncleared fault behind.
pmbus_core will pick the fault on the next register_check(). The register
check will fails regardless of the actual register support by the chip.
This leads to missing attributes or debugfs entries for chips that should
provide them.
We cannot rely on register_check() as PMBUS_SMBALERT_MASK may be read-only.
Unconditionally clear the page fault after setting PMBUS_SMBALERT_MASK to
avoid the problem.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 221819ca4c ("hwmon: (pmbus/core) Add interrupt support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Message-ID: <20241105-tps25990-v4-5-0e312ac70b62@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use _pmbus_read_byte_data() rather than calling smbus directly to check
the write protection status. This give a chance to device implementing
write protection differently to report back on the actual write protection
status.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Message-ID: <20241105-tps25990-v4-2-0e312ac70b62@baylibre.com>
[groeck: Fix page parameter of _pmbus_read_byte_data()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for LTC7841. The LTC7841 is a high performance
PolyPhase® single output synchronous boost converter controller.
Multiphase operation reduces input and output capacitor
requirements and allows the use of smaller inductors than the
single-phase equivalent.
The relevant registers in the LTC7841 are similar to the
LTC7880, only reduced by some amount. So it's just a matter of adding
the chip id. The device also doesn't support polling, on top of the
reduced register set, so a separate case for setting the chip info is
added.
Signed-off-by: Mariel Tinaco <Mariel.Tinaco@analog.com>
Message-ID: <20241029013734.293024-4-Mariel.Tinaco@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While touching these structs, also remove commas after the sentinel
entries and use a consistent indention style.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Message-ID: <20240918123150.1540161-7-u.kleine-koenig@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull hwmon updates from Guenter Roeck:
"New drivers:
- driver for Sophgo SG2042 external hardware monitor
- thermal sensor driver for Surface Aggregator Module
Added support to existing drivers:
- oxp-sensors: Support for multiple new devices.
- nct6775: Added G15CF to ASUS WMI monitoring list
Modernizations:
- driver cleanup and update to use with_info API: ina2xx, lm92,
lm95234, max1619, max1668, and max6697.
API updates:
- removed unused devm_hwmon_device_unregister() API function
Other notable changes
- implement and use generic bus access delay for pmbus drivers
- use with scoped for each OF child loop in several drivers
- module unloading fixes for gsc-hwmon and ntc_thermistor drivers
- converted various drivers to use multi-byte regmap operations
- adt7475: Improved devicetree based configuration
- ltc2947: Move to firmware agnostic API
- ltc2978: Converted devicetree description to yaml
- max16065: Addressed overflows when writing limit attributes
Various other minor cleanups, fixes and improvements"
* tag 'hwmon-for-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (96 commits)
hwmon: Remove devm_hwmon_device_unregister() API function
hwmon: (sch5636) Print unknown ID in error string via %*pE
hwmon: (sht21) Use %*ph to print small buffer
hwmon: (pmbus/mpq7932) Constify struct regulator_desc
hwmon: pmbus: pli12096bc: Add write delay
hwmon: pmbus: zl6100: Use generic code
hwmon: pmbus: ucd9000: Use generic code
hwmon: pmbus: max15301: Use generic code
hwmon: pmbus: Implement generic bus access delay
hwmon: (ina2xx) Use shunt voltage to calculate current
hwmon: (ina2xx) Add support for current limits
hwmon: (ina2xx) Pass register to alert limit write functions
hwmon: (ina2xx) Convert to use with_info hwmon API
hwmon: (ina2xx) Move ina2xx_get_value()
hwmon: (ina2xx) Set alert latch
hwmon: (ina2xx) Consolidate chip initialization code
hwmon: (ina2xx) Fix various overflow issues
hwmon: (ina2xx) Re-initialize chip using regmap functions
hwmon: (ina2xx) Use local regmap pointer if used more than once
hwmon: (ina2xx) Mark regmap_config as const
...
The current implementation of pmbus_show_boolean assumes that all devices
support write-back operation of status register to clear pending warnings
or faults. Since clearing individual bits in the status registers was only
introduced in PMBus specification 1.2, this operation may not be supported
by some older devices. This can result in an error while reading boolean
attributes such as temp1_max_alarm.
Fetch PMBus revision supported by the device and modify pmbus_show_boolean
so that it only tries to clear individual status bits if the device is
compliant with PMBus specs >= 1.2. Otherwise clear all fault indicators
on the current page after a fault status was reported.
Fixes: 35f165f089 ("hwmon: (pmbus) Clear pmbus fault/warning bits after read")
Signed-off-by: Patryk Biel <pbiel7@gmail.com>
Message-ID: <20240909-pmbus-status-reg-clearing-v1-1-f1c0d68c6408@gmail.com>
[groeck:
Rewrote description
Moved revision detection code ahead of clear faults command
Assigned revision if return value from PMBUS_REVISION command is 0
Improved return value check from calling _pmbus_write_byte_data()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'struct regulator_desc' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security, especially when the structure holds some
function pointers.
This also makes mpq7932_regulators_desc consistent with
mpq7932_regulators_desc_one which is already a "static const struct
regulator_desc".
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
3516 2264 0 5780 1694 drivers/hwmon/pmbus/mpq7932.o
After:
=====
text data bss dec hex filename
5396 384 0 5780 1694 drivers/hwmon/pmbus/mpq7932.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Message-ID: <c0585a07547ec58d99a5bff5e02b398114bbe312.1725784343.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tests on PLI12096bc showed that sometimes a small delay is necessary
after a write operation before a new operation can be processed.
If not respected the device will probably NACK the data phase of
the SMBus transaction. Tests showed that the probability to observe
transaction errors can be raised by either reading sensor data or
toggling the regulator enable.
Further tests showed that 250 microseconds, as used previously for
the CLEAR_FAULTS workaround, is sufficient.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Message-ID: <20240902075319.585656-5-patrick.rudolph@9elements.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some drivers, like the max15301 or zl6100, are intentionally delaying
SMBus communications, to prevent transmission errors. As this is necessary
on additional PMBus compatible devices, implement a generic delay mechanism
in the pmbus core.
Introduces two delay settings in the pmbus_driver_info struct, one applies
to every SMBus transaction and the other is for write transaction only.
Once set by the driver the SMBus traffic, using the generic pmbus access
helpers, is automatically delayed when necessary.
The two settings are:
access_delay:
- Unit in microseconds
- Stores the accessed timestamp after every SMBus access
- Delays when necessary before the next SMBus access
write_delay:
- Unit in microseconds
- Stores the written timestamp after a write SMBus access
- Delays when necessary before the next SMBus access
This allows to drop the custom delay code from the drivers and easily
introduce this feature in additional pmbus drivers.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Message-ID: <20240902075319.585656-1-patrick.rudolph@9elements.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit ac0c26bae6 ("hwmon: (lm25066) Use i2c_get_match_data()") changed
enum chips to start with 1 instead of 0, under the assumption that
the data pointer in of_device_id must not start with 0 (NULL) if
i2c_get_match_data() is used. However, that is perfectly fine as long as
there is also an i2c_device_id array with the same data which is used
as fallback in that case.
Let enum chips start with 0 to avoid confusion against other drivers
where the enum starts with 0 and i2c_get_match_data() is used as well.
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Earlier it was assumed that the data pointer in of_device_id must not start
with 0 (NULL) if i2c_get_match_data() is used. However, it turns out that
this is perfectly fine as long as there is also an i2c_device_id array with
the same data, which is used as fallback in that case.
Let enum chips start with 0 to avoid confusion against other drivers
where the enum starts with 0 and i2c_get_match_data() is used as well.
While doing that, remove chip_id from struct mp2856_data since it is only
used in the probe function, and typecast the result of i2c_get_match_data()
to kernel_ulong_t to avoid the double typecast.
Cc: Peter Yin <peteryin.openbmc@gmail.com>
Cc: Potin Lai <potin.lai.pt@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Infineon XDP710
- EC Chip driver for Lenovo ThinkStation motherboards
- Analog Devices ADP1050
Improved support for existing drivers:
- emc1403: Convert to with_info API; Support for EMC1428 and EMC1438
- nzxt-kraken3: Support for NZXT Kraken 2023
- aquacomputer_d5next: Support for Octo flow sensors
- pmbus/adm1275: Support for ADM1281
- dell-smm: Supportt for Precision 7540 and G5 5505
Other notable cleanup:
- max6639: Use regmap
- Remove unused structure fields from multiple drivers
- Drop explicit initialization of struct i2c_device_id::driver_data
to zero
- Improve configuration mode handling in it87 driver
- jc42: Drop support for I2C_CLASS_SPD
- Various conversions to devicetree schema
- Add HAS_IOPORT dependencies as needed
Minor fixes and improvements to max31790, coretemp, aspeed-g6-pwm-tach,
pwm-fan, pmbus/mp2975, acpi_power_meter, and lm70 drivers"
* tag 'hwmon-for-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (52 commits)
hwmon: (nzxt-kraken3) Bail out for unsupported device variants
hwmon: (emc1403) Add support for EMC1428 and EMC1438.
hwmon: Drop explicit initialization of struct i2c_device_id::driver_data to 0 (part 2)
hwmon: (emc1403) Add support for conversion interval configuration
hwmon: (emc1403) Support 11 bit accuracy
hwmon: (emc1403) Convert to with_info API
hwmon: (max6639) Use regmap
hwmon: (npcm750-pwm-fan) Remove another unused field in struct npcm7xx_cooling_device
hwmon: (npcm750-pwm-fan) Remove an unused field in struct npcm7xx_cooling_device
hwmon: (stts751) Remove an unused field in struct stts751_priv
hwmon: Drop explicit initialization of struct i2c_device_id::driver_data to 0
hwmon: (max31790) revise the scale to write pwm
hwmon: (nzxt-kraken3) Add support for NZXT Kraken 2023 (standard and Elite) models
hwmon: (nzxt-kraken3) Decouple device names from kinds
hwmon: (it87) Remove tests nolonger required
hwmon: (it87) Test for chipset before entering configuration mode
hwmon: (it87) Do not enter configuration mode for some chiptypes
hwmon: (it87) Rename FEAT_CONF_NOEXIT to FEAT_NOCONF as more descriptive of requirement
hwmon: (pmbus) Add support for Infineon XDP710
dt-bindings: hwmon: Add infineon xdp710 driver bindings
...
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
This is a follow up to commit d8a66f3621 ("hwmon: Drop explicit
initialization of struct i2c_device_id::driver_data to 0") which I
created before identifying a few corner cases in my conversion script.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240508072027.2119857-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for ADP1050 Digital Controller for Isolated Power Supplies
with PMBus interface Voltage, Current and Temperature Monitor.
The ADP1050 implements several features to enable a robust
system of parallel and redundant operation for customers who
require high availability. The device can measure voltage,
current and temperature that can be used in different
techniques to identify and safely shut down an erroneous
power supply in parallel operation mode.
Signed-off-by: Radu Sabau <radu.sabau@analog.com>
Link: https://lore.kernel.org/r/20240321142201.10330-2-radu.sabau@analog.com
[groeck: Fixed corrupted link in documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The current driver code no longer perfrom internal conversion from
VID to direct. Instead it configures READ_VOUT using MFR_DC_LOOP_CTRL.
Correct the comment message inside the 'mp2975_read_byte_data'
function to match the driver logic.
Signed-off-by: Konstantin Aladyshev <aladyshev22@gmail.com>
Fixes: c60fe56c16 ("hwmon: (pmbus/mp2975) Fix driver initialization for MP2975 device")
Link: https://lore.kernel.org/r/20240127154844.989-1-aladyshev22@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The commit 1feb31e810 ("hwmon: (pmbus/mp2975) Simplify VOUT code")
has introduced a bug that makes it impossible to initialize MP2975
device:
"""
mp2975 5-0020: Failed to identify chip capabilities
i2c i2c-5: new_device: Instantiated device mp2975 at 0x20
i2c i2c-5: delete_device: Deleting device mp2975 at 0x20
"""
Since the 'read_byte_data' function was removed from the
'pmbus_driver_info ' structure the driver no longer reports correctly
that VOUT mode is direct. Therefore 'pmbus_identify_common' fails
with error, making it impossible to initialize the device.
Restore 'read_byte_data' function to fix the issue.
Tested:
- before: it is not possible to initialize MP2975 device with the
'mp2975' driver,
- after: 'mp2975' correctly initializes MP2975 device and all sensor
data is correct.
Fixes: 1feb31e810 ("hwmon: (pmbus/mp2975) Simplify VOUT code")
Signed-off-by: Konstantin Aladyshev <aladyshev22@gmail.com>
Link: https://lore.kernel.org/r/20240126205714.2363-1-aladyshev22@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
