Now that all three branches of the switch end up doing the same thing,
we can move the call to hci_uart_register_device() past it and unify the
error message.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In preparation for unduplicating the hci_uart registration code,
schedule a devres action for disabling the SUSCLK rather than doing it
manually.
We cannot really use devm_clk_get_enabled() as we also set the rate
before enabling the clock. While this should in theory work, I don't
want to risk breaking existing users. One solution for the future is to
add devm_clk_get_enabled_with_rate() to the clock framework.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds handling for system suspend and resume. While the host enters
suspend state, the driver will drive the chip into low power state.
Similarly when system is resuming, the driver will wake up the chip.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for IW615 chipset with it's bootloader signature
and firmware file.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for AW693 A1 chipset with it's bootloader signature
and firmware file.
No firmware name change needed for AW693 A0 chipset.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch implements functions for ISO data send and receive in btusb
driver for MediaTek's controller.
MediaTek defines a specific interrupt endpoint for ISO data transmissin
because the characteristics of interrupt endpoint are similar to the
application of ISO data which can support guaranteed transmissin
bandwidth, enough maximum data length and error checking mechanism.
Driver sets up ISO interface and endpoints in btusb_mtk_setup and clears
the setup in btusb_mtk_shutdown. These flow can't move to btmtk.c due to
btusb_driver is only defined in btusb.c when claiming/relaesing interface.
ISO packet anchor stops when driver suspending and resubmit interrupt urb
for ISO data when driver resuming.
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Move btusb_recv_acl_mtk from btusb.c to btmtk.c which holds
vendor specific stuff and would make btusb.c clean.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Move btusb_mtk_[setup, shutdown] and related function from
btusb.c to btmtk.c which holds vendor specific stuff and
would make btusb.c clean.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Move btusb_mtk_hci_wmt_sync from btusb.c to btmtk.c which holds
vendor specific stuff and would make btusb.c clean.
Add usb.h header to btmtksdio.c/btmtkuart.c for usb related element
defined in btmtk.h
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add suspend/resum callback function in btusb_data which are reserved
for vendor specific usage during suspend/resume. hdev->suspend will be
added before stop traffic in btusb_suspend and hdev-> resume will be
added after resubmit urb in btusb_resume.
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Update the code to immediately return an error code if accessing a
related register fails. This ensures that our desired logic for
subsequent register operations is maintained and allows us to promptly
catch any unexpected errors.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Remove the unnecessary goto tag whether there is an error or not, we have
to free the buffer at the end of the function.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
We unnecessarily fallthrough the case for QCA6390 when initializing the
device and hit the condition where - due to the lack of the enable-gpio
- we disable power management despite using the power sequencer. We don't
need to look for clocks on this model so it makes more sense to just
register the hci device and break the switch.
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 9a15ce6857 ("Bluetooth: qca: use the power sequencer for QCA6390")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # RB5
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BT_HCIUART_QCA, which is a bool and an HCI UART component, uses now
power sequencing, so we need to be sure BT_HCIUART_QCA=y and
POWER_SEQUENCING=m cannot happen:
/usr/bin/aarch64-linux-gnu-ld: drivers/bluetooth/hci_qca.o: in function `qca_serdev_probe':
drivers/bluetooth/hci_qca.c:2401:(.text+0xc48): undefined reference to `devm_pwrseq_get'
/usr/bin/aarch64-linux-gnu-ld: drivers/bluetooth/hci_qca.o: in function `qca_power_shutdown':
drivers/bluetooth/hci_qca.c:2192:(.text+0x29e8): undefined reference to `pwrseq_power_off'
/usr/bin/aarch64-linux-gnu-ld: drivers/bluetooth/hci_qca.o: in function `qca_power_on':
drivers/bluetooth/hci_qca.c:1808:(.text+0x3390): undefined reference to `pwrseq_power_on'
Fixes: 9a15ce6857 ("Bluetooth: qca: use the power sequencer for QCA6390")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This handles the timeout error codes sent by the chip as part of the
bootloader signatures during firmware download process.
When the bootloader does not receive a response packet from the host
within a specific time, it adds an error code to the bootloader
signature while requesting for the FW chunk from the same offset.
The host is expected to clear this error code with a NAK, and reply to
only those bootloader signatures which have error code 0.
However, the driver was ignoring this error code and replying with the
firmware chunks instead, which is apparently ignored by the chip and the
chip resends the same bootloader signature with the error code again. This
happens in a loop until the error code self clears and firmware download
proceeds ahead, adding a couple of milliseconds to the total firmware
download time.
Commit 689ca16e52 was an initial implementation which simply printed
the following line during driver debug:
- FW Download received err 0x04 from chip
This commit adds the expected handling to the error codes.
This error handling is valid for data_req bootloader signatures for V3
and future bootloader versions.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Fixes: 689ca16e52 ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This updates the firmware names of 3 chipsets: w8987, w8997, w9098.
These changes are been done to standardize chip specific firmware
file names to be in sync with firmware names of newer chipsets.
The naming convention for BT-only files would be as follows:
For dual-radio WiFi+BT chipsets:
- <protocol-BT><chip-name>_bt_v<HW-version>.bin
For tri-radio WiFi+BT+15.4 chipsets:
- <protocol-BT><protocol-15.4><chip-name>_bt_v<HW-version>.bin
To maintain backward compatibility, this commit adds a provision to
request older firmware file name, if new firmware file name not found in
/lib/firmware/nxp/.
A new device tree property has been introduced called firmware-name, to
override the hardcoded firmware names (old and new) in the driver.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This new variant needs a different core2_window1 and always uses
beamforming.
The BAR2 also has an offset (RAM start, presumably), so add that.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
[sven: rebased, updated some comments, mentioned 4388 in Kconfig]
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When HCI raw sockets are opened, the Bluetooth kernel module doesn't
track CIS/BIS connections. User-space applications have to identify
ISO data by maintaining connection information and look up the mapping
for each ACL data packet received. Besides, btsnoop log captured in
kernel couldn't tell ISO data from ACL data in this case.
To avoid additional lookups, this patch introduces vendor-specific
packet classification for Intel BT controllers to distinguish
ISO data packets from ACL data packets.
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Remove memset(0) after dma_alloc_coherent(), which already zeroes out
the memory, and fix the following two Coccinelle/coccicheck warnings
reported by zalloc-simple.cocci:
btintel_pcie.c:837:19-37: WARNING: dma_alloc_coherent used in
/* Allocate full chunk of data buffer for DMA first and do indexing and
* initialization next, so it can be freed easily
*/
rxq->buf_v_addr already zeroes out memory, so memset is not needed
btintel_pcie.c:792:19-37: WARNING: dma_alloc_coherent used in
/* Allocate full chunk of data buffer for DMA first and do indexing and
* initialization next, so it can be freed easily
*/
txq->buf_v_addr already zeroes out memory, so memset is not needed
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is preferred to use sizeof(*pointer) instead of sizeof(type)
due to the type of the variable can change and one needs not
change the former (unlike the latter). This patch has no effect
on runtime behavior.
Signed-off-by: Erick Archer <erick.archer@outlook.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
'hci_nokia_radio_hdr' looks like it was unused since it's
initial commit.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Free irq before releasing irq vector.
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Firmware sequencer (FSEQ) is a common code shared across Bluetooth
and Wifi. Printing FSEQ will help to debug if there is any mismatch
between Bluetooth and Wifi FSEQ.
Make 'btintel_print_fseq_info' public and use it in btintel_pcie.c.
dmesg:
....
[ 5335.695740] Bluetooth: hci0: Device booted in 33872 usecs
[ 5335.695918] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-0190-0291.ddc
[ 5335.697011] Bluetooth: hci0: Applying Intel DDC parameters completed
[ 5335.697837] Bluetooth: hci0: Firmware timestamp 2024.20 buildtype 0 build 62871
[ 5335.697848] Bluetooth: hci0: Firmware SHA1: 0xeffdce06
[ 5335.698655] Bluetooth: hci0: Fseq status: Success (0x00)
[ 5335.698666] Bluetooth: hci0: Fseq executed: 00.00.04.176
[ 5335.698670] Bluetooth: hci0: Fseq BT Top: 00.00.04.176
[ 5335.750204] Bluetooth: MGMT ver 1.22
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add the support of MT7922 bluetooth subsystem reset that was called the
auto revert to self-recover from the fatal error in the controller like
the host encounters HCI cmd timeout or the controller crashes.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Hao Qin <hao.qin@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reset the controller before downloading the firmware to improve its
reliability. This includes situations like cold or warm reboots, ensuring
the controller is in its initial state before starting the firmware
download.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Hao Qin <hao.qin@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Extract the function btusb_mtk_subsys_reset from the btusb_mtk_reset
for the future handling of resetting bluetooth controller without
the USB reset.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Hao Qin <hao.qin@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Apply the common btmtk_fw_get_filename to avoid the similar coding in each
driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Include a shared function to get the firmware name, to prevent repeating
code for similar chipsets.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Current flow iterates the ACPI table associated with Bluetooth
controller looking for PPAG method. Method name can be directly passed
to acpi_evaluate_object function instead of iterating the table.
Fixes: c585a92b2f ("Bluetooth: btintel: Set Per Platform Antenna Gain(PPAG)")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds a new flag BTNXPUART_FW_DOWNLOAD_ABORT which handles the
situation where driver is removed while firmware download is in
progress.
logs:
modprobe btnxpuart
[65239.230431] Bluetooth: hci0: ChipID: 7601, Version: 0
[65239.236670] Bluetooth: hci0: Request Firmware: nxp/uartspi_n61x_v1.bin.se
rmmod btnxpuart
[65241.425300] Bluetooth: hci0: FW Download Aborted
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Tested-by: Guillaume Legoupil <guillaume.legoupil@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BCM4377_TIMEOUT is always used to wait for completitions and their API
expects a timeout in jiffies instead of msecs.
Fixes: 8a06127602 ("Bluetooth: hci_bcm4377: Add new driver for BCM4377 PCIe boards")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This sets the default power save mode setting to enabled.
The power save feature is now stable and stress test issues, such as the
TX timeout error, have been resolved.
commit c7ee0bc8db32 ("Bluetooth: btnxpuart: Resolve TX timeout error in
power save stress test")
With this setting, the driver will send the vendor command to FW at
startup, to enable power save feature.
User can disable this feature using the following vendor command:
hcitool cmd 3f 23 03 00 00 (HCI_NXP_AUTO_SLEEP_MODE)
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit 272970be3d ("Bluetooth: hci_qca: Fix driver shutdown on closed
serdev") will cause below regression issue:
BT can't be enabled after below steps:
cold boot -> enable BT -> disable BT -> warm reboot -> BT enable failure
if property enable-gpios is not configured within DT|ACPI for QCA6390.
The commit is to fix a use-after-free issue within qca_serdev_shutdown()
by adding condition to avoid the serdev is flushed or wrote after closed
but also introduces this regression issue regarding above steps since the
VSC is not sent to reset controller during warm reboot.
Fixed by sending the VSC to reset controller within qca_serdev_shutdown()
once BT was ever enabled, and the use-after-free issue is also fixed by
this change since the serdev is still opened before it is flushed or wrote.
Verified by the reported machine Dell XPS 13 9310 laptop over below two
kernel commits:
commit e00fc2700a3f ("Bluetooth: btusb: Fix triggering coredump
implementation for QCA") of bluetooth-next tree.
commit b23d98d46d ("Bluetooth: btusb: Fix triggering coredump
implementation for QCA") of linus mainline tree.
Fixes: 272970be3d ("Bluetooth: hci_qca: Fix driver shutdown on closed serdev")
Cc: stable@vger.kernel.org
Reported-by: Wren Turkal <wt@penguintechs.org>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218726
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Wren Turkal <wt@penguintechs.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
check pdata return of skb_pull_data, instead of data.
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Vijay Satija <vijay.satija@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Some Broadcom controllers found on Apple Silicon machines abuse the
reserved bits inside the PHY fields of LE Extended Advertising Report
events for additional flags. Add a quirk to drop these and correctly
extract the Primary/Secondary_PHY field.
The following excerpt from a btmon trace shows a report received with
"Reserved" for "Primary PHY" on a 4388 controller:
> HCI Event: LE Meta Event (0x3e) plen 26
LE Extended Advertising Report (0x0d)
Num reports: 1
Entry 0
Event type: 0x2515
Props: 0x0015
Connectable
Directed
Use legacy advertising PDUs
Data status: Complete
Reserved (0x2500)
Legacy PDU Type: Reserved (0x2515)
Address type: Random (0x01)
Address: 00:00:00:00:00:00 (Static)
Primary PHY: Reserved
Secondary PHY: No packets
SID: no ADI field (0xff)
TX power: 127 dBm
RSSI: -60 dBm (0xc4)
Periodic advertising interval: 0.00 msec (0x0000)
Direct address type: Public (0x00)
Direct address: 00:00:00:00:00:00 (Apple, Inc.)
Data length: 0x00
Cc: stable@vger.kernel.org
Fixes: 2e7ed5f5e6 ("Bluetooth: hci_sync: Use advertised PHYs on hci_le_ext_create_conn_sync")
Reported-by: Janne Grunau <j@jannau.net>
Closes: https://lore.kernel.org/all/Zjz0atzRhFykROM9@robin
Tested-by: Janne Grunau <j@jannau.net>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
