Pull char / misc / IIO fixes from Greg KH:
"Here are some char/misc/iio and other driver fixes for 6.16-rc7.
Included in here are:
- IIO driver fixes for reported problems
- Interconnect driver fixes for reported problems
- nvmem driver fixes
- bunch of comedi driver fixes for long-term bugs
- Kconfig dependancy fixes for mux drivers
- other small driver fixes for reported problems.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-6.16-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (35 commits)
nvmem: layouts: u-boot-env: remove crc32 endianness conversion
misc: amd-sbi: Explicitly clear in/out arg "mb_in_out"
misc: amd-sbi: Address copy_to/from_user() warning reported in smatch
misc: amd-sbi: Address potential integer overflow issue reported in smatch
comedi: comedi_test: Fix possible deletion of uninitialized timers
comedi: Fix initialization of data for instructions that write to subdevice
comedi: Fix use of uninitialized data in insn_rw_emulate_bits()
comedi: das6402: Fix bit shift out of bounds
comedi: aio_iiro_16: Fix bit shift out of bounds
comedi: pcl812: Fix bit shift out of bounds
comedi: das16m1: Fix bit shift out of bounds
comedi: Fix some signed shift left operations
comedi: Fail COMEDI_INSNLIST ioctl if n_insns is too large
nvmem: imx-ocotp: fix MAC address byte length
MAINTAINERS: add miscdevice Rust abstractions
mux: mmio: Fix missing CONFIG_REGMAP_MMIO
iio: dac: ad3530r: Fix incorrect masking for channels 4-7 in powerdown mode
iio: adc: ad7380: fix adi,gain-milli property parsing
iio: adc: ad7949: use spi_is_bpw_supported()
iio: accel: fxls8962af: Fix use after free in fxls8962af_fifo_flush
...
Fixes for a few clk drivers and bindings:
- Add a missing property to the Mediatek MT8188 clk binding to
keep binding checks happy
- Avoid an OOB by setting the correct number of parents in
dispmix_csr_clk_dev_data
- Allocate clk_hw structs early in probe to avoid an ordering
issue where clk_parent_data points to an unallocated clk_hw
when the child clk is registered before the parent clk in the
SCMI clk driver
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
dt-bindings: clock: mediatek: Add #reset-cells property for MT8188
clk: imx: Fix an out-of-bounds access in dispmix_csr_clk_dev_data
clk: scmi: Handle case where child clocks are initialized before their parents
Pull networking fixes from Paolo Abeni:
"Including fixes from Bluetooth.
Current release - regressions:
- tcp: refine sk_rcvbuf increase for ooo packets
- bluetooth: fix attempting to send HCI_Disconnect to BIS handle
- rxrpc: fix over large frame size warning
- eth: bcmgenet: initialize u64 stats seq counter
Previous releases - regressions:
- tcp: correct signedness in skb remaining space calculation
- sched: abort __tc_modify_qdisc if parent class does not exist
- vsock: fix transport_{g2h,h2g} TOCTOU
- rxrpc: fix bug due to prealloc collision
- tipc: fix use-after-free in tipc_conn_close().
- bluetooth: fix not marking Broadcast Sink BIS as connected
- phy: qca808x: fix WoL issue by utilizing at8031_set_wol()
- eth: am65-cpsw-nuss: fix skb size by accounting for skb_shared_info
Previous releases - always broken:
- netlink: fix wraparounds of sk->sk_rmem_alloc.
- atm: fix infinite recursive call of clip_push().
- eth:
- stmmac: fix interrupt handling for level-triggered mode in DWC_XGMAC2
- rtsn: fix a null pointer dereference in rtsn_probe()"
* tag 'net-6.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (37 commits)
net/sched: sch_qfq: Fix null-deref in agg_dequeue
rxrpc: Fix oops due to non-existence of prealloc backlog struct
rxrpc: Fix bug due to prealloc collision
MAINTAINERS: remove myself as netronome maintainer
selftests/net: packetdrill: add tcp_ooo-before-and-after-accept.pkt
tcp: refine sk_rcvbuf increase for ooo packets
net/sched: Abort __tc_modify_qdisc if parent class does not exist
net: ethernet: ti: am65-cpsw-nuss: Fix skb size by accounting for skb_shared_info
net: thunderx: avoid direct MTU assignment after WRITE_ONCE()
selftests/tc-testing: Create test case for UAF scenario with DRR/NETEM/BLACKHOLE chain
atm: clip: Fix NULL pointer dereference in vcc_sendmsg()
atm: clip: Fix infinite recursive call of clip_push().
atm: clip: Fix memory leak of struct clip_vcc.
atm: clip: Fix potential null-ptr-deref in to_atmarpd().
net: phy: smsc: Fix link failure in forced mode with Auto-MDIX
net: phy: smsc: Force predictable MDI-X state on LAN87xx
net: phy: smsc: Fix Auto-MDIX configuration when disabled by strap
net: stmmac: Fix interrupt handling for level-triggered mode in DWC_XGMAC2
rxrpc: Fix over large frame size warning
net: airoha: Fix an error handling path in airoha_probe()
...
The datasheets refer to the first Ethernet controller as GMAC0, not
EMAC0.
Rename the compatible string to align with the datasheets. A fix for
the device trees will be sent separately.
Fixes: 0454b9057e ("dt-bindings: net: sun8i-emac: Add A523 EMAC0 compatible")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250628054438.2864220-2-wens@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull i2c fixes from Wolfram Sang:
- designware: initialise msg_write_idx during transfer
- microchip: check return value from core xfer call
- realtek: add 'reg' property constraint to the device tree
* tag 'i2c-for-6.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
dt-bindings: i2c: realtek,rtl9301: Fix missing 'reg' constraint
i2c: microchip-core: re-fix fake detections w/ i2cdetect
i2c/designware: Fix an initialization issue
Pull input updates from Dmitry Torokhov:
- support for Acer NGR 200 Controller added to xpad driver
- xpad driver will no longer log errors about URBs at sudden disconnect
- a fix for potential NULL dereference in cs40l50-vibra driver
- several drivers have been switched to using scnprintf() to suppress
warnings about potential output truncation
* tag 'input-for-v6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cs40l50-vibra - fix potential NULL dereference in cs40l50_upload_owt()
Input: alps - use scnprintf() to suppress truncation warning
Input: iqs7222 - explicitly define number of external channels
Input: xpad - support Acer NGR 200 Controller
Input: xpad - return errors from xpad_try_sending_next_out_packet() up
Input: xpad - adjust error handling for disconnect
Input: apple_z2 - drop default ARCH_APPLE in Kconfig
Input: Fully open-code compatible for grepping
dt-bindings: HID: i2c-hid: elan: Introduce Elan eKTH8D18
Input: psmouse - switch to use scnprintf() to suppress truncation warning
Input: lifebook - switch to use scnprintf() to suppress truncation warning
Input: alps - switch to use scnprintf() to suppress truncation warning
Input: atkbd - switch to use scnprintf() to suppress truncation warning
Input: fsia6b - suppress buffer truncation warning for phys
Input: iqs626a - replace snprintf() with scnprintf()
Jonathan writes:
iio: 1st set of fixes for the 6.16 cycle
The usual mixed back of the recent and ancient issues that have surfaced
so far this cycle.
iio-core
- Fix a possible out of bounds write on writing string terminator.
iio-backend:
- Fix a possible out of bounds write on writing string terminator.
adi,ad3530r
- Fix wrong masking for channels 4-7 in powerdown mode as they are in a
second register and mask assumed all in one larger register.
adi,ad7380
- Fix parsing of adi,gain-milli property by reading it as u16 as specified
in the binding.
adi,ad7606
- Tweak dt-binding to allow both interrupts and backend to be wired up
resolving some dt_schema warnings.
- Mask value before returning it in register read as for parallel busses
both the value and (unwanted) address are read back.
adi,ad7949
- Use spi_is_bpw_supported() to correctly handle bits_per_word_mask == 0
which means default value of 8.
invensense,mpu3050
- Fix wrong number of interrupts in the binding as minItems should have
been maxItems.
maxim,max1363
- Two related fixes for a long running mismatch between array indexes
that now results in warnings after the core gained a sanity check.
Resulted in unnecessary channels being sampled.
nxp,fxls8962
- Fix a use after free in fxls8962af_fifo_flush() if it races with buffer
mode tear down.
st,sensors
- Stop using indio_dev->dev before it was initialized as the parent device
should be used anyway for error messages and similar.
st,stm32-adc
- Fix a race when installing chained IRQ handler.
x-powers,axp20x_adc
- Add missing sentinel in ADC channel map (avoid out of bounds read).
* tag 'iio-fixes-for-6.16a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: dac: ad3530r: Fix incorrect masking for channels 4-7 in powerdown mode
iio: adc: ad7380: fix adi,gain-milli property parsing
iio: adc: ad7949: use spi_is_bpw_supported()
iio: accel: fxls8962af: Fix use after free in fxls8962af_fifo_flush
iio: adc: axp20x_adc: Add missing sentinel to AXP717 ADC channel maps
dt-bindings: iio: gyro: invensense,mpu3050: change irq maxItems
iio: common: st_sensors: Fix use of uninitialize device structs
iio: adc: adi-axi-adc: fix ad7606_bus_reg_read()
dt-bindings: iio: adc: adi,ad7606: fix dt_schema validation warning
iio: adc: max1363: Reorder mode_list[] entries
iio: adc: max1363: Fix MAX1363_4X_CHANS/MAX1363_8X_CHANS[]
iio: adc: stm32-adc: Fix race in installing chained IRQ handler
iio: fix potential out-of-bound write
iio: backend: fix out-of-bound write
Pull networking fixes from Paolo Abeni:
"Including fixes from Bluetooth.
Current release - new code bugs:
- eth:
- txgbe: fix the issue of TX failure
- ngbe: specify IRQ vector when the number of VFs is 7
Previous releases - regressions:
- sched: always pass notifications when child class becomes empty
- ipv4: fix stat increase when udp early demux drops the packet
- bluetooth: prevent unintended pause by checking if advertising is active
- virtio: fix error reporting in virtqueue_resize
- eth:
- virtio-net:
- ensure the received length does not exceed allocated size
- fix the xsk frame's length check
- lan78xx: fix WARN in __netif_napi_del_locked on disconnect
Previous releases - always broken:
- bluetooth: mesh: check instances prior disabling advertising
- eth:
- idpf: convert control queue mutex to a spinlock
- dpaa2: fix xdp_rxq_info leak
- amd-xgbe: align CL37 AN sequence as per databook"
* tag 'net-6.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (38 commits)
vsock/vmci: Clear the vmci transport packet properly when initializing it
dt-bindings: net: sophgo,sg2044-dwmac: Drop status from the example
net: ngbe: specify IRQ vector when the number of VFs is 7
net: wangxun: revert the adjustment of the IRQ vector sequence
net: txgbe: request MISC IRQ in ndo_open
virtio_net: Enforce minimum TX ring size for reliability
virtio_net: Cleanup '2+MAX_SKB_FRAGS'
virtio_ring: Fix error reporting in virtqueue_resize
virtio-net: xsk: rx: fix the frame's length check
virtio-net: use the check_mergeable_len helper
virtio-net: remove redundant truesize check with PAGE_SIZE
virtio-net: ensure the received length does not exceed allocated size
net: ipv4: fix stat increase when udp early demux drops the packet
net: libwx: fix the incorrect display of the queue number
amd-xgbe: do not double read link status
net/sched: Always pass notifications when child class becomes empty
nui: Fix dma_mapping_error() check
rose: fix dangling neighbour pointers in rose_rt_device_down()
enic: fix incorrect MTU comparison in enic_change_mtu()
amd-xgbe: align CL37 AN sequence as per databook
...
Pull tty/serial driver fixes from Greg KH:
"Here are five small serial and tty and vt fixes for 6.16-rc4. Included
in here are:
- kerneldoc fixes for recent vt changes
- imx serial driver fix
- of_node sysfs fix for a regression
- vt missing notification fix
- 8250 dt bindings fix
All of these have been in linux-next for a while with no reported issues"
* tag 'tty-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
dt-bindings: serial: 8250: Make clocks and clock-frequency exclusive
serial: imx: Restore original RXTL for console to fix data loss
serial: core: restore of_node information in sysfs
vt: fix kernel-doc warnings in ucs_get_fallback()
vt: add missing notification when switching back to text mode
Fix following dt_schema warning when offload is used:
DTC [C] arch/arm/boot/dts/xilinx/zynq-zed-adv7511-ad7606.dtb
/home/angelo/dev-baylibre/linux-iio/arch/arm/boot/dts/xilinx/zynq-zed-adv7511-ad7606.dtb: adc@0: 'oneOf' conditional failed, one must be fixed:
'interrupts' is a required property
'io-backends' is a required property
from schema $id: http://devicetree.org/schemas/iio/adc/adi,ad7606.yaml#
There isn't any reason that we couldn't have interrupts wired up at the
same time we are using io-backends or SPI offload, so dropping off the
related "oneOf" block entirely.
Fixes: 81fe5529e8 ("dt-bindings: iio: adc: adi,ad7606: add SPI offload properties")
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20250526-wip-bl-ad7606-dtschema-fixes-v2-1-9bd56d039489@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull devicetree fixes from Rob Herring:
- Convert altr,uart-1.0 and altr,juart-1.0 to DT schema. These were
applied for nios2, but never sent upstream.
- Fix extra '/' in fsl,ls1028a-reset '$id' path
- Fix warnings in ti,sn65dsi83 schema due to unnecessary $ref.
* tag 'devicetree-fixes-for-6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: serial: Convert altr,uart-1.0 to DT schema
dt-bindings: serial: Convert altr,juart-1.0 to DT schema
dt-bindings: soc: fsl,ls1028a-reset: Drop extra "/" in $id
dt-bindings: drm/bridge: ti-sn65dsi83: drop $ref to fix lvds-vod* warnings
The 8250 binding before converting to json-schema states,
- clock-frequency : the input clock frequency for the UART
or
- clocks phandle to refer to the clk used as per Documentation/devicetree
for clock-related properties, where "or" indicates these properties
shouldn't exist at the same time.
Additionally, the behavior of Linux's driver is strange when both clocks
and clock-frequency are specified: it ignores clocks and obtains the
frequency from clock-frequency, left the specified clocks unclaimed. It
may even be disabled, which is undesired most of the time.
But "anyOf" doesn't prevent these two properties from coexisting, as it
considers the object valid as long as there's at LEAST one match.
Let's switch to "oneOf" and disallows the other property if one exists,
precisely matching the original binding and avoiding future confusion on
the driver's behavior.
Fixes: e69f5dc623 ("dt-bindings: serial: Convert 8250 to json-schema")
Cc: stable <stable@kernel.org>
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250623093445.62327-1-ziyao@disroot.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull i2c fixes from Wolfram Sang:
- subsystem: convert drivers to use recent callbacks of struct
i2c_algorithm A typical after-rc1 cleanup, which I couldn't send in
time for rc2
- tegra: fix YAML conversion of device tree bindings
- k1: re-add a check which got lost during upstreaming
* tag 'i2c-for-6.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: k1: check for transfer error
i2c: use inclusive callbacks in struct i2c_algorithm
dt-bindings: i2c: nvidia,tegra20-i2c: Specify the required properties
Pull libnvdimm fix from Ira Weiny:
"This converts the pmem-region device tree bindings to YAML to fix
errors and bring it up to date"
* tag 'libnvdimm-fixes-6.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dt-bindings: pmem: Convert binding to YAML
The Elan eKTH8D18 touchscreen controller is an I2C HID device with a
longer boot-up time. Power sequence timing wise it is compatible with
the eKTH6A12NAY, with a power-on delay of at least 5ms, 20ms
out-of-reset for I2C ack response, and 150ms out-of-reset for I2C HID
enumeration, both shorter than what the eKTH6A12NAY requires.
Enumeration and subsequent operation follows the I2C HID standard.
Add a compatible string for it with the ekth6a12nay one as a fallback.
No enum was used as it is rare to actually add new entries. These
chips are commonly completely backward compatible, and unless the
power sequencing delays change, there is no real effort being made to
keep track of new parts, which come out constantly.
Also drop the constraints on the I2C address since it's not really
part of the binding.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20250617082004.1653492-2-wenst@chromium.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Specify the properties which are essential and which are not for the
Tegra I2C driver to function correctly. This was not added correctly when
the TXT binding was converted to yaml. All the existing DT nodes have
these properties already and hence this does not break the ABI.
dmas and dma-names which were specified as a must in the TXT binding
is now made optional since the driver can work in PIO mode if dmas are
missing.
Fixes: f10a9b722f ("dt-bindings: i2c: tegra: Convert to json-schema”)
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Cc: <stable@vger.kernel.org> # v5.17+
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Andi Shyti <andi@smida.it>
Link: https://lore.kernel.org/r/20250603153022.39434-1-akhilrajeev@nvidia.com
Convert the Altera JTAG UART binding to DT schema. The "ALTR,uart-1.0"
compatible has long been deprecated, so drop it.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Convert the Altera JTAG UART binding to DT schema. The "ALTR,juart-1.0"
compatible has long been deprecated, so drop it.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Pull RISC-V updates from Palmer Dabbelt:
- Support for the FWFT SBI extension, which is part of SBI 3.0 and a
dependency for many new SBI and ISA extensions
- Support for getrandom() in the VDSO
- Support for mseal
- Optimized routines for raid6 syndrome and recovery calculations
- kexec_file() supports loading Image-formatted kernel binaries
- Improvements to the instruction patching framework to allow for
atomic instruction patching, along with rules as to how systems need
to behave in order to function correctly
- Support for a handful of new ISA extensions: Svinval, Zicbop, Zabha,
some SiFive vendor extensions
- Various fixes and cleanups, including: misaligned access handling,
perf symbol mangling, module loading, PUD THPs, and improved uaccess
routines
* tag 'riscv-for-linus-6.16-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (69 commits)
riscv: uaccess: Only restore the CSR_STATUS SUM bit
RISC-V: vDSO: Wire up getrandom() vDSO implementation
riscv: enable mseal sysmap for RV64
raid6: Add RISC-V SIMD syndrome and recovery calculations
riscv: mm: Add support for Svinval extension
RISC-V: Documentation: Add enough title underlines to CMODX
riscv: Improve Kconfig help for RISCV_ISA_V_PREEMPTIVE
MAINTAINERS: Update Atish's email address
riscv: uaccess: do not do misaligned accesses in get/put_user()
riscv: process: use unsigned int instead of unsigned long for put_user()
riscv: make unsafe user copy routines use existing assembly routines
riscv: hwprobe: export Zabha extension
riscv: Make regs_irqs_disabled() more clear
perf symbols: Ignore mapping symbols on riscv
RISC-V: Kconfig: Fix help text of CMDLINE_EXTEND
riscv: module: Optimize PLT/GOT entry counting
riscv: Add support for PUD THP
riscv: xchg: Prefetch the destination word for sc.w
riscv: Add ARCH_HAS_PREFETCH[W] support with Zicbop
riscv: Add support for Zicbop
...
Pull more spi updates from Mark Brown:
"A small set of updates that came in during the merge window, we've
got:
- Some small fixes for the Broadcom and spi-pci1xxxx drivers
- A change to the QPIC SNAND driver to flag that the error correction
features are less useful than people might be expecting
- A new device ID for the SOPHGO SG2042
- The addition of Yang Shen as a Huawei maintainer"
* tag 'spi-v6.16-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-qpic-snand: document the limited bit error reporting capability
spi: bcm63xx-hsspi: fix shared reset
spi: bcm63xx-spi: fix shared reset
MAINTAINERS: Update HiSilicon SFC driver maintainer
MAINTAINERS: Update HiSilicon SPI Controller driver maintainer
spi: dt-bindings: spi-sg2044-nor: Add SOPHGO SG2042
spi: spi-pci1xxxx: Fix Probe failure with Dual SPI instance with INTx interrupts
Pull pwm fixes from Uwe Kleine-König:
"axi-pwmgen: Fix handling of external clock
The pwm-axi-pwmgen device is backed by an FPGA and can be synthesized
in different ways. Relevant here is that it can use one or two
external clock signals. These fix clock handling for the two clocks
case"
* tag 'pwm/for-6.16-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
pwm: axi-pwmgen: fix missing separate external clock
dt-bindings: pwm: adi,axi-pwmgen: Fix clocks
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.16-rc1.
Included in here are the following:
- USB offload support for audio devices.
I think this takes the record for the most number of patch series
(30+) over the longest period of time (2+ years) to get merged
properly.
Many props go to Wesley Cheng for seeing this effort through, they
took a major out-of-tree hacked-up-monstrosity that was created by
multiple vendors for their specific devices, got it all merged into
a semi-coherent set of changes, and got all of the different major
subsystems to agree on how this should be implemented both with
changes to their code as well as userspace apis, AND wrangled the
hardware companies into agreeing to go forward with this, despite
making them all redo work they had already done in their private
device trees.
This feature offers major power savings on embedded devices where a
USB audio stream can continue to flow while the rest of the system
is sleeping, something that devices running on battery power really
care about. There are still some more small tweaks left to be done
here, and those patches are still out for review and arguing among
the different hardware companies, but this is a major step forward
and a great example of how to do upstream development well.
- small number of thunderbolt fixes and updates, things seem to be
slowing down here (famous last words...)
- xhci refactors and reworking to try to handle some rough corner
cases in some hardware implementations where things don't always
work properly
- typec driver updates
- USB3 power management reworking and updates
- Removal of some old and orphaned UDC gadget drivers that had not
been used in a very long time, dropping over 11 thousand lines from
the tree, always a nice thing, making up for the 12k lines added
for the USB offload feature.
- lots of little updates and fixes in different drivers
All of these have been in linux-next for over 2 weeks, the USB offload
logic has been in there for 8 weeks now, with no reported issues"
* tag 'usb-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (172 commits)
ALSA: usb-audio: qcom: fix USB_XHCI dependency
ASoC: qdsp6: fix compile-testing without CONFIG_OF
usb: misc: onboard_usb_dev: fix build warning for CONFIG_USB_ONBOARD_DEV_USB5744=n
usb: typec: tipd: fix typo in TPS_STATUS_HIGH_VOLAGE_WARNING macro
USB: typec: fix const issue in typec_match()
USB: gadget: udc: fix const issue in gadget_match_driver()
USB: gadget: fix up const issue with struct usb_function_instance
USB: serial: pl2303: add new chip PL2303GC-Q20 and PL2303GT-2AB
USB: serial: bus: fix const issue in usb_serial_device_match()
usb: usbtmc: Fix timeout value in get_stb
usb: usbtmc: Fix read_stb function and get_stb ioctl
ALSA: qc_audio_offload: try to reduce address space confusion
ALSA: qc_audio_offload: avoid leaking xfer_buf allocation
ALSA: qc_audio_offload: rename dma/iova/va/cpu/phys variables
ALSA: usb-audio: qcom: Fix an error handling path in qc_usb_audio_probe()
usb: misc: onboard_usb_dev: Fix usb5744 initialization sequence
dt-bindings: usb: ti,usb8041: Add binding for TI USB8044 hub controller
usb: misc: onboard_usb_dev: Add support for TI TUSB8044 hub
usb: gadget: lpc32xx_udc: Use USB API functions rather than constants
usb: gadget: epautoconf: Use USB API functions rather than constants
...
Pull tty/serial updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.16-rc1.
A little more churn than normal in this portion of the kernel for this
development cycle, Jiri and Nicholas were busy with cleanups and
reviews and fixes for the vt unicode handling logic which composed
most of the overall work in here.
Major changes are:
- vt unicode changes/reverts/changes from Nicholas. This should help
out a lot with screen readers and others that rely on vt console
support
- lock guard additions to the core tty/serial code to clean up lots
of error handling logic
- 8250 driver updates and fixes
- device tree conversions to yaml
- sh-sci driver updates
- other small cleanups and updates for serial drivers and tty core
portions
All of these have been in linux-next for 2 weeks with no reported issues"
* tag 'tty-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (105 commits)
tty: serial: 8250_omap: fix TX with DMA for am33xx
vt: add VT_GETCONSIZECSRPOS to retrieve console size and cursor position
vt: bracketed paste support
vt: remove VT_RESIZE and VT_RESIZEX from vt_compat_ioctl()
vt: process the full-width ASCII fallback range programmatically
vt: make use of ucs_get_fallback() when glyph is unavailable
vt: add ucs_get_fallback()
vt: create ucs_fallback_table.h_shipped with gen_ucs_fallback_table.py
vt: introduce gen_ucs_fallback_table.py to create ucs_fallback_table.h
vt: move glyph determination to a separate function
vt: make sure displayed double-width characters are remembered as such
vt: ucs.c: fix misappropriate in_range() usage
serial: max3100: Replace open-coded parity calculation with parity8()
dt-bindings: serial: 8250_omap: Drop redundant properties
dt-bindings: serial: Convert socionext,milbeaut-usio-uart to DT schema
dt-bindings: serial: Convert microchip,pic32mzda-uart to DT schema
dt-bindings: serial: Convert arm,sbsa-uart to DT schema
dt-bindings: serial: Convert snps,arc-uart to DT schema
dt-bindings: serial: Convert marvell,armada-3700-uart to DT schema
dt-bindings: serial: Convert lantiq,asc to DT schema
...
Pull char / misc / iio driver updates from Greg KH:
"Here is the big char/misc/iio and other small driver subsystem pull
request for 6.16-rc1.
Overall, a lot of individual changes, but nothing major, just the
normal constant forward progress of new device support and cleanups to
existing subsystems. Highlights in here are:
- Large IIO driver updates and additions and device tree changes
- Android binder bugfixes and logfile fixes
- mhi driver updates
- comedi driver updates
- counter driver updates and additions
- coresight driver updates and additions
- echo driver removal as there are no in-kernel users of it
- nvmem driver updates
- spmi driver updates
- new amd-sbi driver "subsystem" and drivers added
- rust miscdriver binding documentation fix
- other small driver fixes and updates (uio, w1, acrn, hpet,
xillybus, cardreader drivers, fastrpc and others)
All of these have been in linux-next for quite a while with no
reported problems"
* tag 'char-misc-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (390 commits)
binder: fix yet another UAF in binder_devices
counter: microchip-tcb-capture: Add watch validation support
dt-bindings: iio: adc: Add ROHM BD79100G
iio: adc: add support for Nuvoton NCT7201
dt-bindings: iio: adc: add NCT7201 ADCs
iio: chemical: Add driver for SEN0322
dt-bindings: trivial-devices: Document SEN0322
iio: adc: ad7768-1: reorganize driver headers
iio: bmp280: zero-init buffer
iio: ssp_sensors: optimalize -> optimize
HID: sensor-hub: Fix typo and improve documentation
iio: admv1013: replace redundant ternary operator with just len
iio: chemical: mhz19b: Fix error code in probe()
iio: adc: at91-sama5d2: use IIO_DECLARE_BUFFER_WITH_TS
iio: accel: sca3300: use IIO_DECLARE_BUFFER_WITH_TS
iio: adc: ad7380: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: adc: ad4695: rename AD4695_MAX_VIN_CHANNELS
iio: adc: ad4695: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: introduce IIO_DECLARE_BUFFER_WITH_TS macros
iio: make IIO_DMA_MINALIGN minimum of 8 bytes
...
Pull MIPS updates from Thomas Bogendoerfer:
- Added support for EcoNet platform
- Added support for parallel CPU bring up on EyeQ
- Other cleanups and fixes
* tag 'mips_6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (23 commits)
MIPS: loongson2ef: lemote-2f: add missing function prototypes
MIPS: loongson2ef: cs5536: add missing function prototypes
MIPS: SMP: Move the AP sync point before the calibration delay
mips: econet: Fix incorrect Kconfig dependencies
MAINTAINERS: Add entry for newly added EcoNet platform.
mips: dts: Add EcoNet DTS with EN751221 and SmartFiber XP8421-B board
dt-bindings: vendor-prefixes: Add SmartFiber
mips: Add EcoNet MIPS platform support
dt-bindings: mips: Add EcoNet platform binding
MIPS: bcm63xx: nvram: avoid inefficient use of crc32_le_combine()
mips: dts: pic32: pic32mzda: Rename the sdhci nodename to match with common mmc-controller binding
MIPS: SMP: Move the AP sync point before the non-parallel aware functions
MIPS: Replace strcpy() with strscpy() in vpe_elfload()
MIPS: BCM63XX: Replace strcpy() with strscpy() in board_prom_init()
mips: ptrace: Improve code formatting and indentation
MIPS: SMP: Implement parallel CPU bring up for EyeQ
mips: Add -std= flag specified in KBUILD_CFLAGS to vdso CFLAGS
MIPS: Loongson64: Add missing '#interrupt-cells' for loongson64c_ls7a
mips: dts: realtek: Add MDIO controller
MIPS: txx9: gpio: use new line value setter callbacks
...
riscv patches for 6.16-rc1, part 2
* Performance improvements
- Add support for vdso getrandom
- Implement raid6 calculations using vectors
- Introduce svinval tlb invalidation
* Cleanup
- A bunch of deduplication of the macros we use for manipulating instructions
* Misc
- Introduce a kunit test for kprobes
- Add support for mseal as riscv fits the requirements (thanks to Lorenzo for making sure of that :))
[Palmer: There was a rebase between part 1 and part 2, so I've had to do
some more git surgery here... at least two rounds of surgery...]
* alex-pr-2: (866 commits)
RISC-V: vDSO: Wire up getrandom() vDSO implementation
riscv: enable mseal sysmap for RV64
raid6: Add RISC-V SIMD syndrome and recovery calculations
riscv: mm: Add support for Svinval extension
riscv: Add kprobes KUnit test
riscv: kprobes: Remove duplication of RV_EXTRACT_ITYPE_IMM
riscv: kprobes: Remove duplication of RV_EXTRACT_UTYPE_IMM
riscv: kprobes: Remove duplication of RV_EXTRACT_RD_REG
riscv: kprobes: Remove duplication of RVC_EXTRACT_BTYPE_IMM
riscv: kprobes: Remove duplication of RVC_EXTRACT_C2_RS1_REG
riscv: kproves: Remove duplication of RVC_EXTRACT_JTYPE_IMM
riscv: kprobes: Remove duplication of RV_EXTRACT_BTYPE_IMM
riscv: kprobes: Remove duplication of RV_EXTRACT_RS1_REG
riscv: kprobes: Remove duplication of RV_EXTRACT_JTYPE_IMM
riscv: kprobes: Move branch_funct3 to insn.h
riscv: kprobes: Move branch_rs2_idx to insn.h
Linux 6.15-rc6
Input: xpad - fix xpad_device sorting
Input: xpad - add support for several more controllers
Input: xpad - fix Share button on Xbox One controllers
...
riscv patches for 6.16-rc1
* Implement atomic patching support for ftrace which finally allows to
get rid of stop_machine().
* Support for kexec_file_load() syscall
* Improve module loading time by changing the algorithm that counts the
number of plt/got entries in a module.
* Zicbop is now used in the kernel to prefetch instructions
[Palmer: There's been two rounds of surgery on this one, so as a result
it's a bit different than the PR.]
* alex-pr: (734 commits)
riscv: Improve Kconfig help for RISCV_ISA_V_PREEMPTIVE
MAINTAINERS: Update Atish's email address
riscv: hwprobe: export Zabha extension
riscv: Make regs_irqs_disabled() more clear
perf symbols: Ignore mapping symbols on riscv
RISC-V: Kconfig: Fix help text of CMDLINE_EXTEND
riscv: module: Optimize PLT/GOT entry counting
riscv: Add support for PUD THP
riscv: xchg: Prefetch the destination word for sc.w
riscv: Add ARCH_HAS_PREFETCH[W] support with Zicbop
riscv: Add support for Zicbop
riscv: Introduce Zicbop instructions
riscv/kexec_file: Fix comment in purgatory relocator
riscv: kexec_file: Support loading Image binary file
riscv: kexec_file: Split the loading of kernel and others
riscv: Documentation: add a description about dynamic ftrace
riscv: ftrace: support direct call using call_ops
riscv: Implement HAVE_DYNAMIC_FTRACE_WITH_CALL_OPS
riscv: ftrace: support PREEMPT
riscv: add a data fence for CMODX in the kernel mode
...
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Pull RTC updates from Alexandre Belloni:
"There are two new drivers this cycle. There is also support for a
negative offset for RTCs that have been shipped with a date set using
an epoch that is before 1970. This unfortunately happens with some
products that ship with a vendor kernel and an out of tree driver.
Core:
- support negative offsets for RTCs that have shipped with an epoch
earlier than 1970
New drivers:
- NXP S32G2/S32G3
- Sophgo CV1800
Drivers:
- loongson: fix missing alarm notifications for ACPI
- m41t80: kickstart ocillator upon failure
- mt6359: mt6357 support
- pcf8563: fix wrong alarm register
- sh: cleanups"
* tag 'rtc-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (39 commits)
rtc: mt6359: Add mt6357 support
rtc: test: Test date conversion for dates starting in 1900
rtc: test: Also test time and wday outcome of rtc_time64_to_tm()
rtc: test: Emit the seconds-since-1970 value instead of days-since-1970
rtc: Fix offset calculation for .start_secs < 0
rtc: Make rtc_time64_to_tm() support dates before 1970
rtc: pcf8563: fix wrong alarm register
rtc: rzn1: support input frequencies other than 32768Hz
rtc: rzn1: Disable controller before initialization
dt-bindings: rtc: rzn1: add optional second clock
rtc: m41t80: reduce verbosity
rtc: m41t80: kickstart ocillator upon failure
rtc: s32g: add NXP S32G2/S32G3 SoC support
dt-bindings: rtc: add schema for NXP S32G2/S32G3 SoCs
dt-bindings: at91rm9260-rtt: add microchip,sama7d65-rtt
dt-bindings: rtc: at91rm9200: add microchip,sama7d65-rtc
rtc: loongson: Add missing alarm notifications for ACPI RTC events
rtc: sophgo: add rtc support for Sophgo CV1800 SoC
rtc: stm32: drop unused module alias
rtc: s3c: drop unused module alias
...
Pull dmaengine updates from Vinod Koul:
"A fairly small update for the dmaengine subsystem. This has a new ARM
dmaengine driver and couple of new device support and few driver
changes:
New support:
- Renesas RZ/V2H(P) dma support for r9a09g057
- Arm DMA-350 driver
- Tegra Tegra264 ADMA support
Updates:
- AMD ptdma driver code removal and optimizations
- Freescale edma error interrupt handler support"
* tag 'dmaengine-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (27 commits)
dmaengine: idxd: Remove unused pointer and macro
arm64: dts: renesas: r9a09g057: Add DMAC nodes
dmaengine: sh: rz-dmac: Add RZ/V2H(P) support
dmaengine: sh: rz-dmac: Allow for multiple DMACs
irqchip/renesas-rzv2h: Add rzv2h_icu_register_dma_req()
dt-bindings: dma: rz-dmac: Document RZ/V2H(P) family of SoCs
dt-bindings: dma: rz-dmac: Restrict properties for RZ/A1H
dmaengine: idxd: Narrow the restriction on BATCH to ver. 1 only
dmaengine: ti: Add NULL check in udma_probe()
fsldma: Set correct dma_mask based on hw capability
dmaengine: idxd: Check availability of workqueue allocated by idxd wq driver before using
dmaengine: xilinx_dma: Set dma_device directions
dmaengine: tegra210-adma: Add Tegra264 support
dt-bindings: Document Tegra264 ADMA support
dmaengine: dw-edma: Add HDMA NATIVE map check
dmaegnine: fsl-edma: add edma error interrupt handler
dt-bindings: dma: fsl-edma: increase maxItems of interrupts and interrupt-names
dmaengine: ARM_DMA350 should depend on ARM/ARM64
dt-bindings: dma: qcom,bam: Document dma-coherent property
dmaengine: Add Arm DMA-350 driver
...
Pull phy updates from Vinod Koul:
"As usual featuring couple of new driver and bunch of new device
support and some driver changes to Freescale, rockchip driver along
with couple of yaml binding conversions.
New Support:
- Qualcomm IPQ5424 qusb2 support, IPQ5018 uniphy-pcie driver
- Rockchip usb2 support for RK3562, RK3036 usb2 phy support
- Samsung exynos2200 eusb2 phy support and driver refactoring for
this support, exynos7870 USBDRD support
- Mediatek MT7988 xs-phy support
- Broadcom BCM74110 usb phy support
- Renesas RZ/V2H(P) usb2 phy support
Updates:
- Freescale phy rate claculation updates, i.MX95 tuning support
- Better error handling for amlogic pcie phy
- Rockchip color depth configuration and management support
- Yaml binding conversion for RK3399 Type-C and PCIe Phy"
* tag 'phy-for-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (77 commits)
phy: tegra: p2u: Broaden architecture dependency
phy: rockchip: inno-usb2: Add usb2 phy support for rk3562
dt-bindings: phy: rockchip,inno-usb2phy: add rk3562
phy: rockchip: inno-usb2: add phy definition for rk3036
dt-bindings: phy: rockchip,inno-usb2phy: add rk3036 compatible
phy: freescale: fsl-samsung-hdmi: Improve LUT search for best clock
phy: freescale: fsl-samsung-hdmi: Refactor finding PHY settings
phy: freescale: fsl-samsung-hdmi: Rename phy_clk_round_rate
phy: renesas: phy-rcar-gen3-usb2: Add USB2.0 PHY support for RZ/V2H(P)
phy: renesas: phy-rcar-gen3-usb2: Sort compatible entries by SoC part number
dt-bindings: phy: renesas,usb2-phy: Document RZ/V2H(P) SoC
dt-bindings: phy: renesas,usb2-phy: Add clock constraint for RZ/G2L family
phy: exynos5-usbdrd: support Exynos USBDRD 3.2 4nm controller
phy: phy-snps-eusb2: add support for exynos2200
phy: phy-snps-eusb2: refactor reference clock init
phy: phy-snps-eusb2: make reset control optional
phy: phy-snps-eusb2: make repeater optional
phy: phy-snps-eusb2: split phy init code
phy: phy-snps-eusb2: refactor constructs names
phy: move phy-qcom-snps-eusb2 out of its vendor sub-directory
...
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Print the actual delay time in pci_bridge_wait_for_secondary_bus()
instead of assuming it was 1000ms (Wilfred Mallawa)
- Revert 'iommu/amd: Prevent binding other PCI drivers to IOMMU PCI
devices', which broke resume from system sleep on AMD platforms and
has been fixed by other commits (Lukas Wunner)
Resource management:
- Remove mtip32xx use of pcim_iounmap_regions(), which is deprecated
and unnecessary (Philipp Stanner)
- Remove pcim_iounmap_regions() and pcim_request_region_exclusive()
and related flags since all uses have been removed (Philipp
Stanner)
- Rework devres 'request' functions so they are no longer 'hybrid',
i.e., their behavior no longer depends on whether
pcim_enable_device or pci_enable_device() was used, and remove
related code (Philipp Stanner)
- Warn (not BUG()) about failure to assign optional resources (Ilpo
Järvinen)
Error handling:
- Log the DPC Error Source ID only when it's actually valid (when
ERR_FATAL or ERR_NONFATAL was received from a downstream device)
and decode into bus/device/function (Bjorn Helgaas)
- Determine AER log level once and save it so all related messages
use the same level (Karolina Stolarek)
- Use KERN_WARNING, not KERN_ERR, when logging PCIe Correctable
Errors (Karolina Stolarek)
- Ratelimit PCIe Correctable and Non-Fatal error logging, with sysfs
controls on interval and burst count, to avoid flooding logs and
RCU stall warnings (Jon Pan-Doh)
Power management:
- Increment PM usage counter when probing reset methods so we don't
try to read config space of a powered-off device (Alex Williamson)
- Set all devices to D0 during enumeration to ensure ACPI opregion is
connected via _REG (Mario Limonciello)
Power control:
- Rename pwrctrl Kconfig symbols from 'PWRCTL' to 'PWRCTRL' to match
the filename paths. Retain old deprecated symbols for
compatibility, except for the pwrctrl slot driver
(PCI_PWRCTRL_SLOT) (Johan Hovold)
- When unregistering pwrctrl, cancel outstanding rescan work before
cleaning up data structures to avoid use-after-free issues (Brian
Norris)
Bandwidth control:
- Simplify link bandwidth controller by replacing the count of Link
Bandwidth Management Status (LBMS) events with a PCI_LINK_LBMS_SEEN
flag (Ilpo Järvinen)
- Update the Link Speed after retraining, since the Link Speed may
have changed (Ilpo Järvinen)
PCIe native device hotplug:
- Ignore Presence Detect Changed caused by DPC.
pciehp already ignores Link Down/Up events caused by DPC, but on
slots using in-band presence detect, DPC causes a spurious Presence
Detect Changed event (Lukas Wunner)
- Ignore Link Down/Up caused by Secondary Bus Reset.
On hotplug ports using in-band presence detect, the reset causes a
Presence Detect Changed event, which mistakenly caused teardown and
re-enumeration of the device. Drivers may need to annotate code
that resets their device (Lukas Wunner)
Virtualization:
- Add an ACS quirk for Loongson Root Ports that don't advertise ACS
but don't allow peer-to-peer transactions between Root Ports; the
quirk allows each Root Port to be in a separate IOMMU group (Huacai
Chen)
Endpoint framework:
- For fixed-size BARs, retain both the actual size and the possibly
larger size allocated to accommodate iATU alignment requirements
(Jerome Brunet)
- Simplify ctrl/SPAD space allocation and avoid allocating more space
than needed (Jerome Brunet)
- Correct MSI-X PBA offset calculations for DesignWare and Cadence
endpoint controllers (Niklas Cassel)
- Align the return value (number of interrupts) encoding for
pci_epc_get_msi()/pci_epc_ops::get_msi() and
pci_epc_get_msix()/pci_epc_ops::get_msix() (Niklas Cassel)
- Align the nr_irqs parameter encoding for
pci_epc_set_msi()/pci_epc_ops::set_msi() and
pci_epc_set_msix()/pci_epc_ops::set_msix() (Niklas Cassel)
Common host controller library:
- Convert pci-host-common to a library so platforms that don't need
native host controller drivers don't need to include these helper
functions (Manivannan Sadhasivam)
Apple PCIe controller driver:
- Extract ECAM bridge creation helper from pci_host_common_probe() to
separate driver-specific things like MSI from PCI things (Marc
Zyngier)
- Dynamically allocate RID-to_SID bitmap to prepare for SoCs with
varying capabilities (Marc Zyngier)
- Skip ports disabled in DT when setting up ports (Janne Grunau)
- Add t6020 compatible string (Alyssa Rosenzweig)
- Add T602x PCIe support (Hector Martin)
- Directly set/clear INTx mask bits because T602x dropped the
accessors that could do this without locking (Marc Zyngier)
- Move port PHY registers to their own reg items to accommodate
T602x, which moves them around; retain default offsets for existing
DTs that lack phy%d entries with the reg offsets (Hector Martin)
- Stop polling for core refclk, which doesn't work on T602x and the
bootloader has already done anyway (Hector Martin)
- Use gpiod_set_value_cansleep() when asserting PERST# in probe
because we're allowed to sleep there (Hector Martin)
Cadence PCIe controller driver:
- Drop a runtime PM 'put' to resolve a runtime atomic count underflow
(Hans Zhang)
- Make the cadence core buildable as a module (Kishon Vijay Abraham I)
- Add cdns_pcie_host_disable() and cdns_pcie_ep_disable() for use by
loadable drivers when they are removed (Siddharth Vadapalli)
Freescale i.MX6 PCIe controller driver:
- Apply link training workaround only on IMX6Q, IMX6SX, IMX6SP
(Richard Zhu)
- Remove redundant dw_pcie_wait_for_link() from
imx_pcie_start_link(); since the DWC core does this, imx6 only
needs it when retraining for a faster link speed (Richard Zhu)
- Toggle i.MX95 core reset to align with PHY powerup (Richard Zhu)
- Set SYS_AUX_PWR_DET to work around i.MX95 ERR051624 erratum: in
some cases, the controller can't exit 'L23 Ready' through Beacon or
PERST# deassertion (Richard Zhu)
- Clear GEN3_ZRXDC_NONCOMPL to work around i.MX95 ERR051586 erratum:
controller can't meet 2.5 GT/s ZRX-DC timing when operating at 8
GT/s, causing timeouts in L1 (Richard Zhu)
- Wait for i.MX95 PLL lock before enabling controller (Richard Zhu)
- Save/restore i.MX95 LUT for suspend/resume (Richard Zhu)
Mobiveil PCIe controller driver:
- Return bool (not int) for link-up check in
mobiveil_pab_ops.link_up() and layerscape-gen4, mobiveil (Hans
Zhang)
NVIDIA Tegra194 PCIe controller driver:
- Create debugfs directory for 'aspm_state_cnt' only when
CONFIG_PCIEASPM is enabled, since there are no other entries (Hans
Zhang)
Qualcomm PCIe controller driver:
- Add OF support for parsing DT 'eq-presets-<N>gts' property for lane
equalization presets (Krishna Chaitanya Chundru)
- Read Maximum Link Width from the Link Capabilities register if DT
lacks 'num-lanes' property (Krishna Chaitanya Chundru)
- Add Physical Layer 64 GT/s Capability ID and register offsets for
8, 32, and 64 GT/s lane equalization registers (Krishna Chaitanya
Chundru)
- Add generic dwc support for configuring lane equalization presets
(Krishna Chaitanya Chundru)
- Add DT and driver support for PCIe on IPQ5018 SoC (Nitheesh Sekar)
Renesas R-Car PCIe controller driver:
- Describe endpoint BAR 4 as being fixed size (Jerome Brunet)
- Document how to obtain R-Car V4H (r8a779g0) controller firmware
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Reorder rockchip_pci_core_rsts because
reset_control_bulk_deassert() deasserts in reverse order, to fix a
link training regression (Jensen Huang)
- Mark RK3399 as being capable of raising INTx interrupts (Niklas
Cassel)
Rockchip DesignWare PCIe controller driver:
- Check only PCIE_LINKUP, not LTSSM status, to determine whether the
link is up (Shawn Lin)
- Increase N_FTS (used in L0s->L0 transitions) and enable ASPM L0s
for Root Complex and Endpoint modes (Shawn Lin)
- Hide the broken ATS Capability in rockchip_pcie_ep_init() instead
of rockchip_pcie_ep_pre_init() so it stays hidden after PERST#
resets non-sticky registers (Shawn Lin)
- Call phy_power_off() before phy_exit() in rockchip_pcie_phy_deinit()
(Diederik de Haas)
Synopsys DesignWare PCIe controller driver:
- Set PORT_LOGIC_LINK_WIDTH to one lane to make initial link training
more robust; this will not affect the intended link width if all
lanes are functional (Wenbin Yao)
- Return bool (not int) for link-up check in dw_pcie_ops.link_up()
and armada8k, dra7xx, dw-rockchip, exynos, histb, keembay,
keystone, kirin, meson, qcom, qcom-ep, rcar_gen4, spear13xx,
tegra194, uniphier, visconti (Hans Zhang)
- Add debugfs support for exposing DWC device-specific PTM context
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Make j721e buildable as a loadable and removable module (Siddharth
Vadapalli)
- Fix j721e host/endpoint dependencies that result in link failures
in some configs (Arnd Bergmann)
Device tree bindings:
- Add qcom DT binding for 'global' interrupt (PCIe controller and
link-specific events) for ipq8074, ipq8074-gen3, ipq6018, sa8775p,
sc7280, sc8180x sdm845, sm8150, sm8250, sm8350 (Manivannan
Sadhasivam)
- Add qcom DT binding for 8 MSI SPI interrupts for msm8998, ipq8074,
ipq8074-gen3, ipq6018 (Manivannan Sadhasivam)
- Add dw rockchip DT binding for rk3576 and rk3562 (Kever Yang)
- Correct indentation and style of examples in brcm,stb-pcie,
cdns,cdns-pcie-ep, intel,keembay-pcie-ep, intel,keembay-pcie,
microchip,pcie-host, rcar-pci-ep, rcar-pci-host, xilinx-versal-cpm
(Krzysztof Kozlowski)
- Convert Marvell EBU (dove, kirkwood, armada-370, armada-xp) and
armada8k from text to schema DT bindings (Rob Herring)
- Remove obsolete .txt DT bindings for content that has been moved to
schemas (Rob Herring)
- Add qcom DT binding for MHI registers in IPQ5332, IPQ6018, IPQ8074
and IPQ9574 (Varadarajan Narayanan)
- Convert v3,v360epc-pci from text to DT schema binding (Rob Herring)
- Change microchip,pcie-host DT binding to be 'dma-noncoherent' since
PolarFire may be configured that way (Conor Dooley)
Miscellaneous:
- Drop 'pci' suffix from intel_mid_pci.c filename to match similar
files (Andy Shevchenko)
- All platforms with PCI have an MMU, so add PCI Kconfig dependency
on MMU to simplify build testing and avoid inadvertent build
regressions (Arnd Bergmann)
- Update Krzysztof Wilczyński's email address in MAINTAINERS
(Krzysztof Wilczyński)
- Update Manivannan Sadhasivam's email address in MAINTAINERS
(Manivannan Sadhasivam)"
* tag 'pci-v6.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (147 commits)
MAINTAINERS: Update Manivannan Sadhasivam email address
PCI: j721e: Fix host/endpoint dependencies
PCI: j721e: Add support to build as a loadable module
PCI: cadence-ep: Introduce cdns_pcie_ep_disable() helper for cleanup
PCI: cadence-host: Introduce cdns_pcie_host_disable() helper for cleanup
PCI: cadence: Add support to build pcie-cadence library as a kernel module
MAINTAINERS: Update Krzysztof Wilczyński email address
PCI: Remove unnecessary linesplit in __pci_setup_bridge()
PCI: WARN (not BUG()) when we fail to assign optional resources
PCI: Remove unused pci_printk()
PCI: qcom: Replace PERST# sleep time with proper macro
PCI: dw-rockchip: Replace PERST# sleep time with proper macro
PCI: host-common: Convert to library for host controller drivers
PCI/ERR: Remove misleading TODO regarding kernel panic
PCI: cadence: Remove duplicate message code definitions
PCI: endpoint: Align pci_epc_set_msix(), pci_epc_ops::set_msix() nr_irqs encoding
PCI: endpoint: Align pci_epc_set_msi(), pci_epc_ops::set_msi() nr_irqs encoding
PCI: endpoint: Align pci_epc_get_msix(), pci_epc_ops::get_msix() return value encoding
PCI: endpoint: Align pci_epc_get_msi(), pci_epc_ops::get_msi() return value encoding
PCI: cadence-ep: Correct PBA offset in .set_msix() callback
...
- Add OF support for parsing DT 'eq-presets-<N>gts' property for lane
equalization presets (Krishna Chaitanya Chundru)
- Read Maximum Link Width from the Link Capabilities register if DT lacks
'num-lanes' property (Krishna Chaitanya Chundru)
- Add Physical Layer 64 GT/s Capability ID and register offsets for 8, 32,
and 64 GT/s lane equalization registers (Krishna Chaitanya Chundru)
- Add generic dwc support for configuring lane equalization presets
(Krishna Chaitanya Chundru)
- Add DT and driver support for PCIe on IPQ5018 SoC (Nitheesh Sekar)
* pci/controller/qcom:
PCI: qcom: Add support for IPQ5018
dt-bindings: PCI: qcom: Add IPQ5018 SoC
PCI: dwc: Add support for configuring lane equalization presets
PCI: Add lane equalization register offsets
PCI: dwc: Update pci->num_lanes to maximum supported link width
PCI: of: Add of_pci_get_equalization_presets() API
Pull LED updates from Lee Jones:
"LED Triggers:
- Allow writing "default" to the sysfs 'trigger' attribute to set an
LED to its default trigger
- If the default trigger is "none", writing "default" will remove the
current trigger
- Updated sysfs ABI documentation for the new "default" trigger
functionality
LED KUnit Testing:
- Provide a skeleton KUnit test suite for the LEDs framework
- Expand the LED class device registration KUnit test to cover more
scenarios, including 'brightness_get' behavior
- Add KUnit tests for the LED lookup and get API ('led_add_lookup',
'devm_led_get')
LED Flash Class:
- Add support for setting flash/strobe duration through a new
'duration_set' op and 'led_set_flash_duration()' function, aligning
with 'V4L2_CID_FLASH_DURATION'
Texas Instruments TPS6131x:
- Add a new driver for the TPS61310/TPS61311 flash LED controllers
- The driver supports the device's three constant-current sinks for
flash and torch modes
LED Core:
- Prevent potential 'snprintf()' truncations in LED names by checking
for buffer overflows
ChromeOS EC LEDs:
- Avoid a -Wflex-array-member-not-at-end GCC warning by replacing an
on-stack flexible structure definition with a utility function call
Multicolor LEDs:
- Fix issue where setting multi_intensity while software blinking is
active could stop blinking
PCA955x LEDs:
- Avoid potential buffer overflow when creating default labels by
changing a field's type to 'u8' and updating format specifiers
PCA995x LEDs:
- Fix a typo (stray space) in an 'of_device_id' entry in the
'pca995x_of_match' table
Kconfig:
- Prevent LED drivers from being enabled by default when
'COMPILE_TEST' is set
Device Property API:
- Split 'device_get_child_node_count()' into a new helper
'fwnode_get_child_node_count()' that doesn't require a device
struct, making the API more symmetrical
Driver Modernization (using 'fwnode_get_child_node_count()'):
- Update 'leds-pwm-multicolor', 'leds-ncp5623' and 'leds-ncp5623' to
use the new 'fwnode_get_child_node_count()' helper, removing their
custom implementation
- As above in the USB Type-C TCPM driver
Driver Modernization (using new GPIO setter callbacks):
- Convert 'leds-lgm-sso' to use new GPIO line value setter callbacks
which return an integer for error handling
- Convert 'leds-pca955x', 'leds-pca9532' and 'leds-tca6507' to use
new GPIO setter callbacks
Documentation:
- Remove the '.rst' extension for 'leds-st1202' in the documentation
index for consistency
LP8860 LEDs:
- Use 'regmap_multi_reg_write()' for EEPROM writes instead of manual
looping
- Use scoped mutex guards and 'devm_mutex_init()' to simplify
function exits and ensure automatic cleanup
- Remove default register definitions that are unused when regmap
caching is not active
- Use 'devm_regulator_get_enable_optional()' to handle the optional
regulator, simplifying enabling and removing manual disabling
- Refactor 'lp8860_unlock_eeprom()' to only perform the unlock
operation, removing the lock part and an unnecessary parameter
- Use a 'devm' action to disable the enable-GPIO, simplifying cleanup
and error paths, and remove the now-empty '.remove()' function
Turris Omnia LEDs:
- Drop unnecessary commas in terminator entries of 'struct attribute'
and 'struct of_device_id' arrays
MT6370 RGB LEDs:
- Use the 'LINEAR_RANGE()' for defining 'struct linear_range' entries
to improve robustness
Texas Instruments TPS6131x:
- Add new devicetree bindings for the TI TPS61310/TPS61311 flash LED
driver"
* tag 'leds-next-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (31 commits)
leds: tps6131x: Add support for Texas Instruments TPS6131X flash LED driver
dt-bindings: leds: Add Texas Instruments TPS6131x flash LED driver
leds: flash: Add support for flash/strobe duration
leds: rgb: leds-mt6370-rgb: Improve definition of some struct linear_range
leds: led-test: Provide tests for the lookup and get infrastructure
leds: led-test: Fill out the registration test to cover more test cases
leds: led-test: Remove standard error checking after KUNIT_ASSERT_*()
leds: pca995x: Fix typo in pca995x_of_match's of_device_id entry
leds: Provide skeleton KUnit testing for the LEDs framework
leds: tca6507: Use new GPIO line value setter callbacks
leds: pca9532: Use new GPIO line value setter callbacks
leds: pca955x: Use new GPIO line value setter callbacks
leds: lgm-sso: Use new GPIO line value setter callbacks
leds: Do not enable by default during compile testing
leds: turris-omnia: Drop commas in the terminator entries
leds: lp8860: Disable GPIO with devm action
leds: lp8860: Only unlock in lp8860_unlock_eeprom()
leds: lp8860: Enable regulator using enable_optional helper
leds: lp8860: Remove default regs when not caching
leds: lp8860: Use new mutex guards to cleanup function exits
...
Pull MFD updates from Lee Jones:
"Samsung Exynos ACPM:
- Populate child platform devices from device tree data
- Introduce a new API, 'devm_acpm_get_by_node()', for child devices
to get the ACPM handle
ROHM PMICs:
- Add support for the ROHM BD96802 scalable companion PMIC to the
BD96801 core driver
- Add support for controlling the BD96802 using the BD96801 regulator
driver
- Add support to the BD96805, which is almost identical to the
BD96801
- Add support to the BD96806, which is similar to the BD96802
Maxim MAX77759:
- Add a core driver for the MAX77759 companion PMIC
- Add a GPIO driver for the expander functions on the MAX77759
- Add an NVMEM driver to expose the non-volatile memory on the
MAX77759
STMicroelectronics STM32MP25:
- Add support for the STM32MP25 SoC to the stm32-lptimer
- Add support for the STM32MP25 to the clocksource driver, handling
new register access requirements
- Add support for the STM32MP25 to the PWM driver, enabling up to two
PWM outputs
Broadcom BCM590xx:
- Add support for the BCM59054 PMU
- Parse the PMU ID and revision to support behavioral differences
between chip revisions
- Add regulator support for the BCM59054
Samsung S2MPG10:
- Add support for the S2MPG10 PMIC, which communicates via the
Samsung ACPM firmware instead of I2C
Exynos ACPM:
- Improve timeout detection reliability by using ktime APIs instead
of a loop counter assumption
- Allow PMIC access during late system shutdown by switching to
'udelay()' instead of a sleeping function
- Fix an issue where reading command results longer than 8 bytes
would fail
- Silence non-error '-EPROBE_DEFER' messages during boot to clean up
logs
Exynos LPASS:
- Fix an error handling path by switching to
'devm_regmap_init_mmio()' to prevent resource leaks
- Fix a bug where 'exynos_lpass_disable()' was called twice in the
remove function
- Fix another resource leak in the probe's error path by using
'devm_add_action_or_reset()'
Samsung SEC:
- Handle the s2dos05, which does not have IRQ support, explicitly to
prevent warnings
- Fix the core driver to correctly handle errors from
'sec_irq_init()' instead of ignoring them
STMPE-SPI:
- Correct an undeclared identifier in the 'MODULE_DEVICE_TABLE' macro
MAINTAINERS:
- Adjust a file path for the Siemens IPC LED drivers entry to fix a
broken reference
Maxim Drivers:
- Correct the spelling of "Electronics" in Samsung copyright headers
across multiple files
General:
- Fix wakeup source memory leaks on device unbind for 88pm886,
as3722, max14577, max77541, max77705, max8925, rt5033, and
sprd-sc27xx drivers
Samsung SEC Drivers:
- Split the driver into a transport-agnostic core ('sec-core') and
transport-specific ('sec-i2c', 'sec-acpm') modules to support
non-I2C devices
- Merge the 'sec-core' and 'sec-irq' modules to reduce memory
consumption
- Move internal APIs to a private header to clean up the public API
- Improve code style by sorting includes, cleaning up headers,
sorting device tables, and using helper macros like
'dev_err_probe()', 'MFD_CELL', and 'REGMAP_IRQ_REG'
- Make regmap configuration for s2dos05/s2mpu05 explicit to improve
clarity
- Rework platform data and regmap instantiation to use OF match data
instead of a large switch statement
ROHM BD96801/2:
- Prepare the driver for new models by separating chip-specific data
into its own structure
- Drop IC name prefix from IRQ resource names in both the MFD and
regulator drivers for simplification
Broadcom BCM590xx:
- Refactor the regulator driver to store descriptions in a table to
ease support for new chips
- Rename BCM59056-specific data to prepare for the addition of other
regulators
- Use 'dev_err_probe()' for cleaner error handling
Exynos ACPM:
- Correct kerneldoc warnings and use the conventional 'np' argument
name
General MFD:
- Convert 'aat2870' and 'tps65010' to use the per-client debugfs
directory provided by the I2C core
- Convert 'sm501', 'tps65010' and 'ucb1x00' to use the new GPIO line
value setter callbacks
- Constify 'regmap_irq_chip' and other structures in '88pm886' to
move data to read-only sections
BCM590xx:
- Drop the unused "id" member from the 'bcm590xx' struct in
preparation for a replacement
Samsung SEC Core:
- Remove forward declarations for functions that no longer exist
SM501:
- Remove the unused 'sm501_find_clock()' function
New Compatibles:
- Google: Add a PMIC child node to the 'google,gs101-acpm-ipc'
binding
- ROHM: Add new bindings for 'rohm,bd96802-regulator' and
'rohm,bd96802-pmic', and add compatibles for BD96805 and BD96806
- Maxim: Add new bindings for 'maxim,max77759-gpio',
'maxim,max77759-nvmem', and the top-level 'maxim,max77759'
- STM: Add 'stm32mp25' compatible to the 'stm32-lptimer' binding
- Broadcom: Add 'bcm59054' compatible
- Atmel/Microchip: Add 'microchip,sama7d65-gpbr' and
'microchip,sama7d65-secumod' compatibles
- Samsung: Add 's2mpg10' compatible to the 'samsung,s2mps11' MFD
binding
- MediaTek: Add compatibles for 'mt6893' (scpsys), 'mt7988-topmisc',
and 'mt8365-infracfg-nao'
- Qualcomm: Add 'qcom,apq8064-mmss-sfpb' and 'qcom,apq8064-sps-sic'
syscon compatibles
Refactoring & Cleanup:
- Convert Broadcom BCM59056 devicetree bindings to YAML and split
them into MFD and regulator parts
- Convert the Microchip AT91 secumod binding to YAML
- Drop unrelated consumer nodes from binding examples to reduce bloat
- Correct indentation and style in various DTS examples"
* tag 'mfd-next-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (81 commits)
mfd: maxim: Correct Samsung "Electronics" spelling in copyright headers
mfd: maxim: Correct Samsung "Electronics" spelling in headers
mfd: sm501: Remove unused sm501_find_clock
mfd: 88pm886: Constify struct regmap_irq_chip and some other structures
dt-bindings: mfd: syscon: Add mediatek,mt8365-infracfg-nao
mfd: sprd-sc27xx: Fix wakeup source leaks on device unbind
mfd: rt5033: Fix wakeup source leaks on device unbind
mfd: max8925: Fix wakeup source leaks on device unbind
mfd: max77705: Fix wakeup source leaks on device unbind
mfd: max77541: Fix wakeup source leaks on device unbind
mfd: max14577: Fix wakeup source leaks on device unbind
mfd: as3722: Fix wakeup source leaks on device unbind
mfd: 88pm886: Fix wakeup source leaks on device unbind
dt-bindings: mfd: Correct indentation and style in DTS example
dt-bindings: mfd: Drop unrelated nodes from DTS example
dt-bindings: mfd: syscon: Add qcom,apq8064-sps-sic
dt-bindings: mfd: syscon: Add qcom,apq8064-mmss-sfpb
mfd: stmpe-spi: Correct the name used in MODULE_DEVICE_TABLE
dt-bindings: mfd: syscon: Add mt7988-topmisc
mfd: exynos-lpass: Fix another error handling path in exynos_lpass_probe()
...
Pull ata updates from Damien Le Moal:
- Simplify ata_print_version_once() using dev_dbg_once() (Heiner)
- Some cleanups of libata-sata code to simplify the sense data fetching
code and use BIT() macro for tag bit handling (Niklas)
- Fix variable name spelling in the sata_sx4 driver (Colin)
- Improve sense data information field handling for passthrough
commands (Igor)
- Add Rockchip RK3576 SoC compatible to the Designware AHCI DT bindings
(Nicolas)
- Add a message to indicate if a port is marked as external or not, to
help with debugging potential issues with LPM (Niklas)
- Convert DT bindings for "ti,dm816-ahci", "apm,xgene-ahci",
"cavium,ebt3000-compact-flash", "marvell,orion-sata", and
"arasan,cf-spear1340" to DT schema (Rob)
- Cleanup and improve the code and related comments for HIPM and DIPM
(host initiated and device initiated power managent) handling.
In particular, keep DIPM disabled while modifying the allowed LPM
states to avoid races with the device initiating power state changes
(Niklas)
* tag 'ata-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: libata-eh: Keep DIPM disabled while modifying the allowed LPM states
ata: libata-eh: Rename no_dipm variable to be more clear
ata: libata-eh: Rename hipm and dipm variables
ata: libata-eh: Add ata_eh_set_lpm() WARN_ON_ONCE
ata: libata-eh: Update DIPM comments to reflect reality
dt-bindings: ata: Convert arasan,cf-spear1340 to DT schema
dt-bindings: ata: Convert marvell,orion-sata to DT schema
dt-bindings: ata: Convert cavium,ebt3000-compact-flash to DT schema
dt-bindings: ata: Convert apm,xgene-ahci to DT schema
dt-bindings: ata: Convert st,ahci to DT schema
dt-bindings: ata: Convert ti,dm816-ahci to DT schema
ata: libata: Print if port is external on boot
dt-bindings: ata: rockchip-dwc-ahci: add RK3576 compatible
ata: libata-scsi: Do not set the INFORMATION field twice for ATA PT
ata: sata_sx4: Fix spelling mistake "parttern" -> "pattern"
ata: libata-sata: Use BIT() macro to convert tag to bit field
ata: libata-sata: Simplify sense_valid fetching
ata: libata-core: Simplify ata_print_version_once
Pull hwmon updates from Guenter Roeck:
"New drivers:
- KEBA fan controller
- KEBA battery monitoring controller
- MAX77705
Support added to existing drivers:
- MAXIMUS VI HERO and ROG MAXIMUS Z90 Formula support (asus-ec-sensors)
- SQ52206 support (ina238)
- lt3074 support (pmbus/lt3074)
- ADPM12160 support (pmbus/max34440)
- MPM82504 and for MPM3695 family support (pmbus/mpq8785)
- Add the Dell OptiPlex 7050 to the DMI whitelist (dell-smm)
- Zen5 Ryzen Desktop support (k10temp)
Various other minor fixes and improvements"
* tag 'hwmon-for-v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (48 commits)
doc: hwmon: acpi_power_meter: Add information about enabling the power capping feature.
hwmon: (isl28022) Fix current reading calculation
hwmon: (lm75) Fix I3C transfer buffer pointer for incoming data
hwmon: Add KEBA fan controller support
hwmon: pmbus: mpq8785: Add support for MPM3695 family
hwmon: pmbus: mpq8785: Add support for MPM82504
hwmon: pmbus: mpq8785: Implement VOUT feedback resistor divider ratio configuration
hwmon: pmbus: mpq8785: Prepare driver for multiple device support
dt-bindings: hwmon: Add bindings for mpq8785 driver
hwmon: (ina238) Modify the calculation formula to adapt to different chips
hwmon: (ina238) Add support for SQ52206
dt-bindings: Add SQ52206 to ina2xx devicetree bindings
hwmon: (ina238) Add ina238_config to save configurations for different chips
hwmon: (ausus-ec-sensors) add MAXIMUS VI HERO.
hwmon: (isl28022, nct7363) Convert to use maple tree register cache
hwmon: (asus-ec-sensors) check sensor index in read_string()
hwmon: (asus-ec-sensors) add ROG MAXIMUS Z90 Formula.
dt-bindings: hwmon: Add Sophgo SG2044 external hardware monitor support
hwmon: (max77705) Add initial support
hwmon: (tmp102) add vcc regulator support
...
Pull hyperv updates from Wei Liu:
- Support for Virtual Trust Level (VTL) on arm64 (Roman Kisel)
- Fixes for Hyper-V UIO driver (Long Li)
- Fixes for Hyper-V PCI driver (Michael Kelley)
- Select CONFIG_SYSFB for Hyper-V guests (Michael Kelley)
- Documentation updates for Hyper-V VMBus (Michael Kelley)
- Enhance logging for hv_kvp_daemon (Shradha Gupta)
* tag 'hyperv-next-signed-20250602' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: (23 commits)
Drivers: hv: Always select CONFIG_SYSFB for Hyper-V guests
Drivers: hv: vmbus: Add comments about races with "channels" sysfs dir
Documentation: hyperv: Update VMBus doc with new features and info
PCI: hv: Remove unnecessary flex array in struct pci_packet
Drivers: hv: Remove hv_alloc/free_* helpers
Drivers: hv: Use kzalloc for panic page allocation
uio_hv_generic: Align ring size to system page
uio_hv_generic: Use correct size for interrupt and monitor pages
Drivers: hv: Allocate interrupt and monitor pages aligned to system page boundary
arch/x86: Provide the CPU number in the wakeup AP callback
x86/hyperv: Fix APIC ID and VP index confusion in hv_snp_boot_ap()
PCI: hv: Get vPCI MSI IRQ domain from DeviceTree
ACPI: irq: Introduce acpi_get_gsi_dispatcher()
Drivers: hv: vmbus: Introduce hv_get_vmbus_root_device()
Drivers: hv: vmbus: Get the IRQ number from DeviceTree
dt-bindings: microsoft,vmbus: Add interrupt and DMA coherence properties
arm64, x86: hyperv: Report the VTL the system boots in
arm64: hyperv: Initialize the Virtual Trust Level field
Drivers: hv: Provide arch-neutral implementation of get_vtl()
Drivers: hv: Enable VTL mode for arm64
...
