This code works, but technically it uses "num_in_bus_fmts" before it
has been initialized so it leads to static checker warnings and probably
KMEMsan warnings at run time. Initialize the variable to zero to
silence the warning.
Fixes: f32df58acc ("drm/bridge: Add the necessary bits to support bus format negotiation")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/YrrIs3hoGcPVmXc5@kili
Allwinner display drivers are split roughly into two generations. The
first generation was found on early 32-bit ARM SoCs and contains DE1.0
and a custom HDMI controller. Clarify that these options only apply to
a specific list of SoCs, and limit selecting them to 32-bit ARM, to
avoid confusion.
The second generation, found in A83T and newer SoCs (both 32-bit and
64-bit), contains a DE2.0 and a DesignWare HDMI controller. Since this
is the most widely-used generation, enable it by default. The previous
default condition (MACH_SUN8I) was limited to 32-bit SoCs. Also enable
the DSI controller by default, which is found on 64-bit SoCs as well.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220702193250.52959-1-samuel@sholland.org
The current code tries to handle the case where CONFIG_PM isn't selected
by first calling our runtime_resume implementation and then properly
report the power state to the runtime_pm core.
This allows to have a functionning device even if pm_runtime_get_*
functions are nops.
However, the device power state if CONFIG_PM is enabled is
RPM_SUSPENDED, and thus our vc4_hdmi_write() and vc4_hdmi_read() calls
in the runtime_pm hooks will now report a warning since the device might
not be properly powered.
Even more so, we need CONFIG_PM enabled since the previous RaspberryPi
have a power domain that needs to be powered up for the HDMI controller
to be usable.
The previous patch has created a dependency on CONFIG_PM, now we can
just assume it's there and only call pm_runtime_resume_and_get() to make
sure our device is powered in bind.
Link: https://lore.kernel.org/r/20220629123510.1915022-39-maxime@cerno.tech
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
nouveau_bo_init() is backed by ttm_bo_init() and ferries its return code
back to the caller. On failures, ttm will call nouveau_bo_del_ttm() and
free the memory.Thus, when nouveau_bo_init() returns an error, the gem
object has already been released. Then the call to nouveau_bo_ref() will
use the freed "nvbo->bo" and lead to a use-after-free bug.
We should delete the call to nouveau_bo_ref() to avoid the use-after-free.
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 019cbd4a4f ("drm/nouveau: Initialize GEM object before TTM object")
Cc: Thierry Reding <treding@nvidia.com>
Cc: <stable@vger.kernel.org> # v5.4+
Link: https://patchwork.freedesktop.org/patch/msgid/20220705132546.2247677-1-niejianglei2021@163.com
cec_unregister_adapter() assumes that the underlying adapter ops are
callable. For example, if the CEC adapter currently has a valid physical
address, then the unregistration procedure will invalidate the physical
address by setting it to f.f.f.f. Whence the following kernel oops
observed after removing the adv7511 module:
Unable to handle kernel execution of user memory at virtual address 0000000000000000
Internal error: Oops: 86000004 [#1] PREEMPT_RT SMP
Call trace:
0x0
adv7511_cec_adap_log_addr+0x1ac/0x1c8 [adv7511]
cec_adap_unconfigure+0x44/0x90 [cec]
__cec_s_phys_addr.part.0+0x68/0x230 [cec]
__cec_s_phys_addr+0x40/0x50 [cec]
cec_unregister_adapter+0xb4/0x118 [cec]
adv7511_remove+0x60/0x90 [adv7511]
i2c_device_remove+0x34/0xe0
device_release_driver_internal+0x114/0x1f0
driver_detach+0x54/0xe0
bus_remove_driver+0x60/0xd8
driver_unregister+0x34/0x60
i2c_del_driver+0x2c/0x68
adv7511_exit+0x1c/0x67c [adv7511]
__arm64_sys_delete_module+0x154/0x288
invoke_syscall+0x48/0x100
el0_svc_common.constprop.0+0x48/0xe8
do_el0_svc+0x28/0x88
el0_svc+0x1c/0x50
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x15c/0x160
Code: bad PC value
---[ end trace 0000000000000000 ]---
Protect against this scenario by unregistering i2c_cec after
unregistering the CEC adapter. Duly disable the CEC clock afterwards
too.
Fixes: 3b1b975003 ("drm: adv7511/33: add HDMI CEC support")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220612144854.2223873-3-alvin@pqrs.dk
The next call to sii8620_burst_get_tx_buf will result in off-by-one
When ctx->burst.tx_count + size == ARRAY_SIZE(ctx->burst.tx_buf). The same
thing happens in sii8620_burst_get_rx_buf.
This patch also change tx_count and tx_buf to rx_count and rx_buf in
sii8620_burst_get_rx_buf. It is unreasonable to check tx_buf's size and
use rx_buf.
Fixes: e19e9c692f ("drm/bridge/sii8620: add support for burst eMSC transmissions")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220518065856.18936-1-hbh25y@gmail.com
Until now, when running at the maximum resolution of 1280x720 at 32bpp
on the JZ4770 SoC the output was garbled, the X/Y position of the
top-left corner of the framebuffer warping to a random position with
the whole image being offset accordingly, every time a new frame was
being submitted.
This problem can be eliminated by using a bigger burst size for the DMA.
Set in each soc_info structure the maximum burst size supported by the
corresponding SoC, and use it in the driver.
Set the new value using regmap_update_bits() instead of
regmap_set_bits(), since we do want to override the old value of the
burst size. (Note that regmap_set_bits() wasn't really valid before for
the same reason, but it never seemed to be a problem).
Cc: <stable@vger.kernel.org>
Fixes: 90b86fcc47 ("DRM: Add KMS driver for the Ingenic JZ47xx SoCs")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20220702230727.66704-1-paul@crapouillou.net
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Christophe Branchereau <cbranchereau@gmail.com>
HDMI 2.1 section 10.3.6 defines an HDMI Forum EDID Extension Override
Data Block, which may contain a different extension count than the base
block claims. Add support for reading more EDID data if available. The
extra blocks aren't parsed yet, though.
Hard-coding the EEODB parsing instead of using the iterators we have is
a bit of a bummer, but we have to be able to do this on a partially
allocated EDID while reading it.
v2:
- Check for CEA Data Block Collection size (Ville)
- Amend commit message and comment about hard-coded parsing
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/57b57a355d62eb91ad1e3cf555978576f2bd9fdd.1656494768.git.jani.nikula@intel.com
Add a new function drm_edid_connector_update() to replace the
combination of calls drm_connector_update_edid_property() and
drm_add_edid_modes(). Usually they are called in the drivers in this
order, however the former needs information from the latter.
Since the new drm_edid_read*() functions no longer call the connector
updates directly, and the read and update are separated, we'll need this
new function for the connector update.
This is all in drm_edid.c simply to keep struct drm_edid opaque.
v2:
- Share code with drm_connector_update_edid_property() (Ville)
- Add comment about override EDID handling
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/75aa3dbc8c9aa26ebbcdeacd98a466ef8d8827f4.1656494768.git.jani.nikula@intel.com
Add functions drm_edid_override_set() and drm_edid_override_reset() to
support "edid_override" connector debugfs, and to hide the details about
it in drm_edid.c. No functional changes at this time.
Also note in the connector.override_edid flag kernel-doc that this is
only supposed to be modified by the code doing debugfs EDID override
handling. Currently, it is still being modified by amdgpu in
create_eml_sink() and handle_edid_mgmt() for reasons unknown. This was
added in commit 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
and later moved to amdgpu_dm.c in commit e7b07ceef2 ("drm/amd/display:
Merge amdgpu_dm_types and amdgpu_dm").
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8f6b4001630cafac5f44aa5913429ac9979743d2.1656494768.git.jani.nikula@intel.com
With the change to 2 pixels/clock, the pixel doubling in the PV
results in doubling each pair of pixels, ie ABABCDCD instead of
AABBCCDD.
Move the pixel doubling to the HDMI block, however this means
that DBLCLK modes now fall foul of requiring even values for
all the horizontal timing parameters.
As both 480i and 576i fail this, attempt to fix up DBLCLK modes
that have odd timings values.
Fixes: 8323989140 ("drm/vc4: hdmi: Support the BCM2711 HDMI controllers")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-34-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Whenever the maximum BPC is changed, vc4_hdmi_encoder_compute_config()
might pick up a different BPC or format depending on the display
capabilities.
That change will have a number of side effects, including the clock
rates and whether the scrambling is enabled.
However, only drm_crtc_state.connectors_changed will be set to true,
since that properly only affects the connector.
This means that while drm_atomic_crtc_needs_modeset() will return true,
and thus drm_atomic_helper_commit_modeset_enables() will call our
encoder atomic_enable() hook, mode_changed will be false.
So crtc_set_mode() will not call our encoder .atomic_mode_set() hook. We
use this hook in vc4 to set the vc4_hdmi_connector_state.output_bpc (and
output_format), and will then reuse the value in .atomic_enable() to select
whether or not scrambling should be enabled.
However, since our clock rate is pre-computed during .atomic_check(), we
end up with the clocks properly configured, but the scrambling disabled,
leading to a blank screen.
Let's set mode_changed to true in our HDMI driver to force the update of
output_bpc, and thus prevent the issue entirely.
Fixes: ba8c0faebb ("drm/vc4: hdmi: Enable 10/12 bpc output")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-32-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Increase the number of post-sync blanking lines on odd fields instead of
decreasing it on even fields. This makes the total number of lines
properly match the modelines.
Additionally fix the value of PV_VCONTROL_ODD_DELAY, which did not take
pixels_per_clock into account, causing some displays to invert the
fields when driven by bcm2711.
Fixes: 682e62c454 ("drm/vc4: Fix support for interlaced modes on HDMI.")
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-31-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
