Pull devicetree updates from Rob Herring:
"DT Bindings:
- Convert and add a bunch of IBM FSI related bindings
- Add a new schema listing legacy compatibles which will (probably)
never be documented. This will silence various checks warning about
them.
- Add bindings for Sierra Wireless mangOH Green SPI IoT interface,
new Arm 2024 Cortex and Neoverse CPUs, QCom sc8180x PDC, QCom SDX75
GPI DMA, imx8mp/imx8qxp fsl,irqsteer, and Renesas RZ/G2UL CRU and
CSI-2 blocks
- Convert Spreadtrum sprd-timer, FSL cpm_qe, FSL fsl,ls-scfg-msi, FSL
q(b)man-*, FSL qoriq-mc, and img,pdc-wdt bindings to DT schema
- Drop obsolete stericsson,abx500.txt
DT core:
- Update dtc to upstream version v1.7.0-93-g1df7b047fe43
- Add support to run DT validation on DTs with applied overlays
- Add helper for creating boolean properties in dynamic nodes and use
that for dynamic PCI nodes
- Clean-up early parsing of '#{address,size}-cells'"
* tag 'devicetree-for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (39 commits)
dt-bindings: timer: sprd-timer: convert to YAML
dt-bindings: incomplete-devices: document devices without bindings
dt-bindings: trivial-devices: document the Sierra Wireless mangOH Green SPI IoT interface
scripts/dtc: Update to upstream version v1.7.0-93-g1df7b047fe43
dt-bindings: soc: fsl: Add fsl,ls1028a-reset for reset syscon node
dt-bindings: soc: fsl: cpm_qe: convert to yaml format
dt-bindings: i2c: i2c-fsi: Convert to json-schema
dt-bindings: fsi: Document the FSI Hub Controller
dt-bindings: fsi: Document the AST2700 FSI controller
dt-bindings: fsi: ast2600-fsi-master: Convert to json-schema
dt-bindings: fsi: ibm,i2cr-fsi-master: Reference common FSI controller
dt-bindings: fsi: Document the FSI controller common properties
dt-bindings: fsi: Document the IBM SBEFIFO engine
dt-bindings: fsi: p9-occ: Convert to json-schema
dt-bindings: fsi: Document the IBM SCOM engine
dt-bindings: fsi: fsi2spi: Document SPI controller child nodes
dt-bindings: interrupt-controller: convert fsl,ls-scfg-msi to yaml
dt-bindings: soc: fsl: Convert q(b)man-* to yaml format
dt-bindings: misc: fsl,qoriq-mc: convert to yaml format
dt-bindings: drop stale Anson Huang from maintainers
...
Pull MFD updates from Lee Jones:
"New Drivers:
- ROHM BD96801 Power Management IC
- Cirrus Logic CS40L50 Haptic Driver with Waveform Memory
- Marvell 88PM886 Power Management IC
New Device Support:
- Keyboard Backlight to ChromeOS Embedded Controller
- LEDs to ChromeOS Embedded Controller
- Charge Control to ChromeOS Embedded Controller
- HW Monitoring Service to ChromeOS Embedded Controller
- AUXADCs to MediaTek MT635{7,8,9} Power Management ICs
New Functionality:
- Allow Syscon consumers to supply their own Regmaps on registration
Fix-ups:
- Constify/staticise applicable data structures
- Remove superfluous/duplicated/unused sections
- Device Tree binding adaptions/conversions/creation
- Trivial; spelling, whitespace, coding-style adaptions
- Utilise centrally provided helpers and macros to aid
simplicity/duplication
- Drop i2c_device_id::driver_data where the value is unused
- Replace ACPI/DT firmware helpers with agnostic variants
- Move over to GPIOD (descriptor-based) APIs
- Annotate a bunch of __counted_by() cases
- Straighten out some includes
Bug Fixes:
- Ensure potentially asserted recent lines are deasserted during
initialisation
- Avoid "<module>.ko is added to multiple modules" warnings
- Supply a bunch of MODULE_DESCRIPTIONs to silence modpost warnings
- Fix Wvoid-pointer-to-enum-cast warnings"
* tag 'mfd-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (87 commits)
mfd: timberdale: Attach device properties to TSC2007 board info
mfd: tmio: Move header to platform_data
mfd: tmio: Sanitize comments
mfd: tmio: Update include files
mmc: tmio/sdhi: Fix includes
mfd: tmio: Remove obsolete io accessors
mfd: tmio: Remove obsolete platform_data
watchdog: bd96801_wdt: Add missing include for FIELD_*()
dt-bindings: mfd: syscon: Add APM poweroff mailbox
dt-bindings: mfd: syscon: Split and enforce documenting MFD children
dt-bindings: mfd: rk817: Merge support for RK809
dt-bindings: mfd: rk817: Fixup clocks and reference dai-common
dt-bindings: mfd: syscon: Add TI's opp table compatible
mfd: omap-usb-tll: Use struct_size to allocate tll
dt-bindings: mfd: Explain lack of child dependency in simple-mfd
dt-bindings: mfd: Dual licensing for st,stpmic1 bindings
mfd: omap-usb-tll: Annotate struct usbtll_omap with __counted_by
mfd: tps6594-core: Remove unneeded semicolon in tps6594_check_crc_mode()
mfd: lm3533: Move to new GPIO descriptor-based APIs
mfd: tps65912: Use devm helper functions to simplify probe
...
Pull arm SoC platform updates from Arnd Bergmann:
"The majority of the updates here are Dmitry Torokhov's cleanups for
platform code in the pxa and tegra platforms, changing custom
platform_data structures into DT-compatible software node
declarations.
The other updates are for the MAINTAINERS file, correcting some stale
or missing entries"
* tag 'soc-arm-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: pxa: fix build breakage on PXA3xx
ti: omap: MAINTAINERS: move Benoît Cousson to CREDITS
amazon: MAINTAINERS: change to odd fixes and Tsahee Zidenberg to CREDITS
MAINTAINERS: thead: add git tree
ARM: spitz: Use software nodes for the ADS7846 touchscreen
ARM: spitz: Use software nodes to describe LED GPIOs
ARM: spitz: Use software nodes to describe MMC GPIOs
ARM: spitz: Use software nodes to describe LCD GPIOs
ARM: spitz: Use software nodes to describe audio GPIOs
ARM: spitz: Use software nodes to describe SPI CS lines
ARM: spitz: Simplify instantiating SPI controller
ARM: pxa/gumstix: convert vbus gpio to use software nodes
ARM: pxa: consolidate GPIO chip platform data
ARM: spitz: fix GPIO assignment for backlight
ARM: tegra: paz00: Use software nodes to describe GPIOs for WiFi rfkill
MAINTAINERS: ARM: airoha: add entry to cover Airoha SoC
bus: vexpress-config: Add missing MODULE_DESCRIPTION() macro
arm64: layerscape: remove redundant EDAC_SUPPORT selection
dt-bindings: arm: Remove obsolete RTSM DCSCB binding
arm: vexpress: Remove obsolete RTSM DCSCB support
Pull SoC dt updates from Arnd Bergmann:
"The devicetree updates are fairly well spread out across platforms,
with Qualcomm making up about a third of the total.
There are three new SoCs in existing product families this:
- NXP i.MX95 is a variant of i.MX93, now with six Cortex-A55 cores
instead of just two as well as a GPU and more high-speed I/O
devices.
- Qualcomm QCS8550 is a variant of SM8550 for IOT devices
- Airoha EN7581 is a 10G-PON network chip and related to the MT7981
Wireless router chip from its parent Mediatek.
In total there are 58 new machines, including four riscv boards and
eight for 32-bit arm.
The most exciting new addition is probably a pair of laptops based on
the Qualcomm x1e80100 (Snapdragon X1 Elite) chip, the Asus Vivobook
S15 and the Lenovo Yoga Slim7x.
Other noteworthy new additions are:
- A total of 20 Qualcomm based machines, mostly Android devices from
Samsung, Motorola and LG, as well as a wireless router and some
reference designs
- Six NXP i.MX based machines, mostly industrial boards along with
some reference designs
- Mediatek sees some interesting Filogic based routers including the
"OpenWRT One", a few new Chromebooks as well as single-board
computers.
- Four machines from Solidrun based on Marvell cn913x, replacing the
older Armada 8000 based counterparts
- The four Amlogic machines are all set top boxes or reference
designs for them
- The nine new Rockchips machines are mostly single-board computers
including some interesting ones based on the rk3588 chip like the
ROCK 5 ITX board and the CM3588 with its four NVMe slots
- The RISC-V boards are all single-board computers based on Starfive
JH7110, Microchip MPFS and Allwinner D1, which all had similar
boards already
There are also a lot of updates to already supported machines, notably
for the TI K3, Rockchips, Freescale and of course Qualcomm platforms"
* tag 'soc-dt-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (846 commits)
arm64: dts: allwinner: h616: add crypto engine node
riscv: dts: add clock generator for Sophgo SG2042 SoC
arm64: dts: rockchip: Add Xunlong Orange Pi 3B
dt-bindings: arm: rockchip: Add Xunlong Orange Pi 3B
arm64: dts: rockchip: Add Radxa ROCK 3B
dt-bindings: arm: rockchip: Add Radxa ROCK 3B
mailmap: Update Luca Weiss's email address
ARM: dts: ixp4xx: nslu2: beeper uses PWM
arm64: dts: rockchip: add ROCK 5 ITX board
dt-bindings: arm: rockchip: Add ROCK 5 ITX board
arm64: dts: rockchip: Add dma-names to uart1 on Pine64 rk3566 devices
arm64: dts: rockchip: Add avdd supplies to hdmi on rock64
arm64: dts: qcom: msm8916-lg-c50: add initial dts for LG Leon LTE
arm64: dts: qcom: msm8916-lg-m216: Add initial device tree
dt-bindings: arm: qcom: Add msm8916 based LG devices
ARM: dts: qcom: msm8960: correct memory base
arm64: dts: qcom: ipq9574: Add icc provider ability to gcc
dt-bindings: interconnect: Add Qualcomm IPQ9574 support
arm64: dts: qcom: sm8150: Add video clock controller node
arm64: dts: qcom: pm6150: Add vibrator
...
Pull SoC driver updates from Arnd Bergmann:
"The updates to the mediatek, allwinner, ti, tegra, microchip, stm32,
samsung, imx, zynq and amlogic platoforms are fairly small maintenance
changes, either addressing minor mistakes or enabling additional
hardware.
The qualcomm platform changes add a number of features and are larger
than the other ones combined, introducing the use of linux/cleanup.h
across several drivers, adding support for Snapdragon X1E and other
SoCs in platform drivers, a new "protection domain mapper" driver, and
a "shared memory bridge" driver.
The cznic "turris omnia" router based on Marvell Armada gets a
platform driver that talks to the board specific microcontroller.
The reset and cache subsystems get a few minor updates to SoC specific
drivers, while the ff-a, scmi and optee firmware drivers get some code
refactoring and new features"
* tag 'soc-drivers-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (122 commits)
firmware: turris-mox-rwtm: Initialize completion before mailbox
firmware: turris-mox-rwtm: Fix checking return value of wait_for_completion_timeout()
firmware: turris-mox-rwtm: Do not complete if there are no waiters
MAINTAINERS: drop riscv list from cache controllers
platform: cznic: turris-omnia-mcu: fix Kconfig dependencies
bus: sunxi-rsb: Constify struct regmap_bus
soc: sunxi: sram: Constify struct regmap_config
platform: cznic: turris-omnia-mcu: Depend on WATCHDOG
platform: cznic: turris-omnia-mcu: Depend on OF
soc: samsung: exynos-pmu: add support for PMU_ALIVE non atomic registers
arm64: stm32: enable scmi regulator for stm32
firmware: qcom: tzmem: blacklist more platforms for SHM Bridge
soc: qcom: wcnss: simplify with cleanup.h
soc: qcom: pdr: simplify with cleanup.h
soc: qcom: ocmem: simplify with cleanup.h
soc: qcom: mdt_loader: simplify with cleanup.h
soc: qcom: llcc: simplify with cleanup.h
firmware: qcom: tzmem: simplify returning pointer without cleanup
soc: qcom: socinfo: Add PM6350 PMIC
arm64: dts: renesas: rz-smarc: Replace fixed regulator for USB VBUS
...
Pull MMC updates from Ulf Hansson:
"MMC host:
- Convert from using tasklet to the BH workqueue
- dw_mmc-bluefield: Add support for eMMC HW reset
- mmc_spi: Allow spi controllers incapable of lower than 400kHz
- sdhci: Rework code to eliminate SDHCI_QUIRK_UNSTABLE_RO_DETECT
- sdhci-brcmstb: Add support for the BCM2712 variant
- sdhci-esdhc-imx: Disable card-detect as system wakeup on S32G platforms
- sdhci-msm: Add support for the SDX75 variant
- sdhci-of-dwcmshc: Enable CQE support for some Rockchip variants
- sdhci-of-esdhc: Convert DT-bindings to yaml
- sdhci-sprd: Convert DT-bindings to yaml
MEMSTICK:
- rtsx_pci_ms: Remove the unused Realtek PCI memstick driver"
* tag 'mmc-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (26 commits)
MAINTAINERS: add 's32@nxp.com' as relevant mailing list for 'sdhci-esdhc-imx' driver
mmc: sdhci-esdhc-imx: obtain the 'per' clock rate after its enablement
mmc: sdhci-esdhc-imx: disable card detect wake for S32G based platforms
dt-bindings: mmc: sdhci-sprd: convert to YAML
mmc: davinci_mmc: report all possible bus widths
mmc: dw_mmc-bluefield: Add support for eMMC HW reset
mmc: dw_mmc: Add support for platform specific eMMC HW reset
mmc: sdhci_am654: Constify struct regmap_config
mmc: Convert from tasklet to BH workqueue
mmc: sdhi: Convert from tasklet to BH workqueue
mmc: mmc_spi: allow for spi controllers incapable of getting as low as 400k
memstick: rtsx_pci_ms: Remove Realtek PCI memstick driver
MAINTAINERS: drop entry for VIA SD/MMC controller
mmc: tmio: Remove obsolete .set_pwr() callback()
mfd: tmio: Remove obsolete .set_clk_div() callback
mmc: sdhci-brcmstb: Add ARCH_BCM2835 option
mmc: sdhci: Eliminate SDHCI_QUIRK_UNSTABLE_RO_DETECT
dt-bindings: mmc: Convert fsl-esdhc.txt to yaml
dt-bindings: mmc: mmc-spi-slot: Change voltage-ranges to uint32-matrix
mmc: add missing MODULE_DESCRIPTION() macros
...
A few more Arm64 DeviceTree updates for v6.11
This introduces support for Lenovo Thinkpad Yoga slim 7x, LG Leon LTE,
and LG K10 (K420n).
In addition to this, all Gen-1 platforms gets the DWC3 quirk to disable
"SuperSpeed in park mode", which resolves an instabliity issue seen in
host mode.
For Fairphone 4, PM6150L and PMK8003 thermal sensors are added and
thermal zones defined.
Two fastrpc contexts on SM6350 are marked as non-secure, to allow
non-secure usage.
The video clock controller on SM8150 is introduced. IPQ9574 GCC is
marked as a interconnect provider. The vibrator block in the PM6150 is
described.
On SC7280 the download mode register is defined for SCM, allowing it to
enable/disable the ramdump support during a system crash.
Lastly, add a mailmap entry for Luca Weiss.
* tag 'qcom-arm64-for-6.11-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (22 commits)
mailmap: Update Luca Weiss's email address
arm64: dts: qcom: msm8916-lg-c50: add initial dts for LG Leon LTE
arm64: dts: qcom: msm8916-lg-m216: Add initial device tree
dt-bindings: arm: qcom: Add msm8916 based LG devices
arm64: dts: qcom: ipq9574: Add icc provider ability to gcc
dt-bindings: interconnect: Add Qualcomm IPQ9574 support
arm64: dts: qcom: sm8150: Add video clock controller node
arm64: dts: qcom: pm6150: Add vibrator
arm64: dts: qcom: sc7280: Enable download mode register write
arm64: dts: qcom: sm7225-fairphone-fp4: Add PM6150L thermals
arm64: dts: qcom: sm7225-fairphone-fp4: Add PMK8003 thermals
arm64: dts: qcom: sm6350: Add missing qcom,non-secure-domain property
arm64: dts: qcom: sdm845: Disable SS instance in Parkmode for USB
arm64: dts: qcom: msm8996: Disable SS instance in Parkmode for USB
arm64: dts: qcom: sm6350: Disable SS instance in Parkmode for USB
arm64: dts: qcom: sm6115: Disable SS instance in Parkmode for USB
arm64: dts: qcom: sdm630: Disable SS instance in Parkmode for USB
arm64: dts: qcom: msm8998: Disable SS instance in Parkmode for USB
arm64: dts: qcom: ipq8074: Disable SS instance in Parkmode for USB
arm64: dts: qcom: ipq6018: Disable SS instance in Parkmode for USB
...
Link: https://lore.kernel.org/r/20240709193406.3966-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
TI SoC driver updates for v6.11
- Update TISCI protocol URL link which was dead
- socinfo: Add j721E SR 2.0 detection support
- MAINTAINER list additions: ti,pruss.yaml and ti,j721e-system-controller.yaml
- pm33xx: log statement improvement
- knav_qmss: minor data structure optimization
* tag 'ti-driver-soc-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
dt-bindings: soc: ti: Move ti,j721e-system-controller.yaml to soc/ti
MAINTAINERS: Add entry for ti,pruss.yaml to TI KEYSTONE MULTICORE NAVIGATOR DRIVERS
soc: ti: k3-socinfo: Add J721E SR2.0
soc: ti: knav_qmss: Constify struct knav_range_ops
firmware: ti_sci: fix TISCI protocol URL link
dt-bindings: ti: fix TISCI protocol URL link
soc: ti: pm33xx: Fix missing newlines in log statements
Link: https://lore.kernel.org/r/20240705151449.s4rngkehjn73favn@stream
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add devicetree binding documentation for the Radxa ROCK 3B board.
The Radxa ROCK 3B is a single-board computer based on the Pico-ITX form
factor (100mm x 75mm). Two versions of the ROCK 3B exists, a community
version based on the RK3568 SoC and an industrial version based on the
RK3568J SoC.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240627211737.1985549-2-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
One new board, the pretty interesting Rock 5 ITX, some improvements
for the Lunzn Fastrhino R6xS boards, allowing dma on uarts connected
to bluetooth modules and an update for the gpu operating points on
rk356x. As well as some minor fixes for missing power-dmains and
ethernet phy binding adherence.
* tag 'v6.11-rockchip-dts64-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: add ROCK 5 ITX board
dt-bindings: arm: rockchip: Add ROCK 5 ITX board
arm64: dts: rockchip: Add dma-names to uart1 on Pine64 rk3566 devices
arm64: dts: rockchip: Add avdd supplies to hdmi on rock64
arm64: dts: rockchip: fixes PHY reset for Lunzn Fastrhino R68S
arm64: dts: rockchip: disable display subsystem for Lunzn Fastrhino R6xS
arm64: dts: rockchip: remove unused usb2 nodes for Lunzn Fastrhino R6xS
arm64: dts: rockchip: fix pmu_io supply for Lunzn Fastrhino R6xS
arm64: dts: rockchip: fix usb regulator for Lunzn Fastrhino R6xS
arm64: dts: rockchip: fix regulator name for Lunzn Fastrhino R6xS
arm64: dts: rockchip: Add dma-names to uart1 on quartz64-b
arm64: dts: rockchip: Update GPU OPP voltages in RK356x SoC dtsi
arm64: dts: rockchip: Add GPU OPP voltage ranges to RK356x SoC dtsi
arm64: dts: rockchip: Drop ethernet-phy-ieee802.3-c22 from PHY compatible string on all RK3588 boards
arm64: dts: rockchip: Add missing power-domains for rk356x vop_mmu
Link: https://lore.kernel.org/r/1998182.CrzyxZ31qj@diego
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm Arm64 DeviceTree updates for v6.11
This introduces 11 new boards, namely:
* ASUS Vivobook S 15
* Lenovo Smart Tab M10 DTS
* Motorola Moto E 2015 LTE (surnia)
* Motorola Moto G 2015 (osprey)
* Motorola Moto G4 Play (harpia)
* Qualcomm AIM300 AIoT development board
* Qualcomm SM8650 Hardware Development Kit (HDK)
* SHIFTphone 8
* Samsung Galaxy Z Fold5
* Schneider HMIBSC board DTS
* TP-Link Archer AX55 v1
Of particular interest here is the Asus Vivobook, the first supported X1
Elite consumer laptop.
For IPQ6018 an SDHCI controller is added and on IPQ9574 an MDIO bus is
described.
The improvements to MSM8916-based devices continues, with sound and
mdoem support added to Acer Iconia Talk S and GPLUS FL8005A, the latter
also gaining BMS support. Samsung Galaxy devices gains PMIC and charger
definitions, NFC support and MUIC. Accelerometer and magnetometer
support is added to the Samsung Galaxy Grand Prime devices.
On MSM8976 definitions for IOMMU, the display subsystem, wifi subsystem,
and Adreno GPU are added.
On MSM8996 UFS core clock frequencies are specified, FastRPC nodes are
added for the audio DSP, glink-edges are described where available, the
display subsystem reset is added.
Venus is introduced on MSM8998 and the "No MSA Ready" quirk is added to
allow ath10k to come up.
GPU support is added to QCM2290 and enabled on the RB1 development
board.
The I2C controller used for communicating with the LT9611UXC HDMI
bridge is temporarily replaced with i2c-gpio while issues with the
builtin controller is diagnosed. The same is done for RB2, on the
QRB4210 platform.
On RB2 TCPM max current draw is corrected and the vreg_l9a regulator is
marked as always on to match expectations.
On the QDU1000 platform, USB is added, secure QFPROM is introduced to
allow LLCC to access OTP data. USB is enabled on the two IDP boards.
SA8775p gains PCIe endpoint definitions, LLCCC support, IMEM and PIL
info regions. Nodes are marked as dma-coherent as needed, a dedicated
carveout for shared memory bridge allocations is introduced.
The SA8775P ride device is split in the two versions r2 and r3.
The SC7180 Trogdor clamshell/detachable fragments are refactored for
convenience, and pwmleds are disabled where unused.
On SC7280 the APR nodes for interfacing with the audio services in audio
DSP firmware are introduced. The Qualcomm SMMU TBUs are described, to
enable improved debug support. QoS clocks are added to interconnects, as
needed in order to operate the QoS settings on some buses.
SuperSpeed in park is disabled for the primary DWC3 instance to address
host controller issues under load.
The PM8008 (camera PMIC) is introduced in Fairphone 5, regulators are
named for better output, and firmware name for IPA is adjusted to the
preferred file format.
The HDMI bridge on Rb3gen2 is described, rtc, gpi-dma and qup nodes are
enabled.
The Type-C port manager found in PM7250b is enabled, for targets not
using pmic-glink firmware for Type-C management.
SC8180X gets a number of smaller corrections, and some cleanups -
related to both functional issues and DeviceTree validation.
The PSHOLD node is marked reserved, after reports that this causes
issues during shutdown. Description of the USB signals are updated to
match the signal path. The PM8008 camera PMIC is added to Lenovo
ThinkPad X13s.
The PM660 PMIC is extended with charger and rradc definitions, and the
SDM670 gains a SMEM region definition.
On SDM845 the Qualcomm SMMU TBU nodes are described, to enable improved
debug output during faults etc. The UFS PHY is associated with its GDSC,
and the DisplayPort controller is wired up to the QMP PHY.
The Lenovo Yoga C630 Embedded Controller is introduced, adding battery
and Type-C port management and altmode support. The C630 also gains WiFI
calibration variant information, to cause selection of the right data.
The missing IPA firmware path is corrected.
For the SDX75 platform, AOSS, IPCC, SDHCI, TCSR, modem SMP2P, I2C and
SPI nodes are introduced. SD-card support is added to the IDP board.
CPUfreq support is introduced for the SM4450 platform.
Missing reset is added to the SDHC controller of SM6115. The UFS PHY
is associated with its GDSC, so is the PHY on SM6350.
On Fairphone 4, the camera pmic (PM8008) is introduced, regulators are
named for more informative debug output, and USB role switching is
enabled.
On the Fairphone 3, vibrator support is added and enabled.
On SM8250, the USB signal paths are properly described in the OF graph,
the UFS PHY gains its required power-domains description.
Thanks to the introduction of PCI power sequence support, the QRB5165
RB5 WiFi chip can now be powered up, so this is added.
Touchscreen interrupt flags are corrected accross a number of Sony
Xperia devices, to remove the unexpected traces from downstream.
On SM8450 an OPP-table is introduced for the PCIe controllers, to
specify the bandwidth and performance state requirements for the
different genrations and link widths. For this the PCIe controllers also
gains interconnect path definitions. The LLCC register layout is
corrected, and the UFS PHY is associated with its GDSC.
On the SM8550 development boards speaker port mapping is added. WiFi
support is finally enabled on the QRD board.
The new AIM300 development platform/board is introduced.
For SM8650 video and camera clock controller are introduced. SCM node
gains details necessary to trigger USB ramdump (download mode) upon a
system crash.
WiFi support and speaker port mapping is added to the QRD and the newly
introduced HDK. On the MTP the USB Type-C connector is describe to be
routed to the PHY.
In addition to the base HDK, a Display Card overlay is also introduced.
For X1 Elite bwmon, fastrpc and GPU support, tsens, and the missing PCIe
6a instance are added. Thermal zones are described. Pmic-glink is
introduced for both CRD and QCP devices, and remaining PMICs are
described. Audio support is also added to the QCP.
An explicit, larger, chunk of CMA memory is added to the various
devices, in order to compensate for the lack of IOMMU for PCIe.
Across a wide range of platforms, the thermal zone polling delays are
removed as supplies are interrupt driven anyways. Also thermal related
is the introduction of GPU thermal throttling, across many SoCs.
The old SMSM implementation is finally transitioned to using the
mailbox-based description and implementation for invoking interrupts on
remote processors. As such interrupt-triggering is converted to use this
mechanism on related platforms.
The usb-role-switch property is removed for all USB instances hard coded
to either host or peripheral across a range of boards.
* tag 'qcom-arm64-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (279 commits)
dt-bindings: arm: qcom: Document samsung,ms013g
arm64: dts: qcom: Add device tree for ASUS Vivobook S 15
dt-bindings: arm: qcom: Add ASUS Vivobook S 15
arm64: dts: qcom: qrb4210-rb2: Correct max current draw for VBUS
arm64: dts: qcom: msm8998: add venus node
arm64: dts: qcom: sa8775p-ride-r3: add new board file
arm64: dts: qcom: move common parts for sa8775p-ride variants into a .dtsi
dt-bindings: arm: qcom: add sa8775p-ride Rev 3
arm64: dts: qcom: sm8550-qrd: add port mapping to speakers
arm64: dts: qcom: sm8550-mtp: add port mapping to speakers
arm64: dts: qcom: sm8550-hdk: add port mapping to speakers
arm64: dts: qcom: sm8650-qrd: add port mapping to speakers
arm64: dts: qcom: sm8650-mtp: add port mapping to speakers
arm64: dts: qcom: sm8650-hdk: add port mapping to speakers
arm64: dts: qcom: sm7225-fairphone-fp4: Name the regulators
arm64: dts: qcom: pm8916: correct thermal zone name
arm64: dts: qcom: x1e80100: Add gpu support
arm64: dts: qcom: x1e80100: Fix USB HS PHY 0.8V supply
arm64: dts: qcom: qcs6490-rb3gen2: enable hdmi bridge
arm64: dts: qcom: sm6115: add resets for sdhc_1
...
Link: https://lore.kernel.org/r/20240706173140.18887-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mvebu dt64 for 6.11 (part 1)
armada-3720: align GPIO keys and LED node namee with bindings
Add description for solidrun cn9130 som and clearfog boards
* tag 'mvebu-dt64-6.11-1' of https://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: add description for solidrun cn9132 cex7 module and clearfog board
arm64: dts: add description for solidrun cn9131 solidwan board
arm64: dts: add description for solidrun cn9130 som and clearfog boards
dt-bindings: arm64: marvell: add solidrun cn9132 CEX-7 evaluation board
dt-bindings: arm64: marvell: add solidrun cn9130 som based boards
arm64: dts: armada-3720: align LED node name with bindings
arm64: dts: armada-3720: align GPIO keys node name with bindings
Link: https://lore.kernel.org/r/87wmlzixln.fsf@BLaptop.bootlin.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
STM32 DT for v6.11, round 1
Highlights:
----------
-MCU:
- Add syscfg missing clock on stm32f429.
- MPU:
- STM32MP13:
- Add camera support on stm32mp135f-dk bord using DCMIPP and
GC2145 sensor.
- Document PWM output for stm32mp135f-dk
- Add goodix touchscreen support on stm32mp135f-dk board.
- Add new DH DHCOR / DHSBC board (Som + carrier board) based on
STM32MP135F SoC.
SOM part contains: STM32MP135F SoC, 512MB DDR2L RAM and
eMMC/SDIO wifi module.
The carrier boards embedds 2 RGMII ETH ports, USB-A,USB-C
and an extansion connector.
- Add Ethernet controller support on stm32mp135f-dk.
It uses LAN8742A PHY based on RMII.
- STMP32MP15:
- Rework Octavo OSD32MP1 split for USB phy.
- Add OP-TEE IRQ for asynchronous notification support.
It allows OP-TEE to trig Linux.
- STM32MP25:
- Add OP-TEE IRQ for asynchronous notification support.
It allows OP-TEE to trig Linux.
- Enable firewall for RCC.
- Add all U(s)ART nodes for stm32mp25.
- Add 3 power domains for low power modes.
- Add HPDMA support.
- Add Ethernet controller (ETH2) support on stm32mp257f-ev1.
It uses Realtek PHY based on RGMII.
- Add and enable SCMI regulator support.
* tag 'stm32-dt-for-v6.11-1' of https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (31 commits)
arm64: dts: st: describe power supplies for stm32mp257f-ev1 board
arm64: dts: st: add scmi regulators on stm32mp25
regulator: Add STM32MP25 regulator bindings
ARM: dts: stm32: omit unused pinctrl groups from stm32mp13 dtb files
arm64: dts: st: enable Ethernet2 on stm32mp257f-ev1 board
arm64: dts: st: add eth2 pinctrl entries in stm32mp25-pinctrl.dtsi
arm64: dts: st: add ethernet1 and ethernet2 support on stm32mp25
arm64: dts: st: add HPDMA nodes on stm32mp251
ARM: dts: stm32: Add ethernet support for DH STM32MP13xx DHCOR DHSBC board
ARM: dts: stm32: order stm32mp13-pinctrl nodes
ARM: dts: stm32: add ethernet1 for STM32MP135F-DK board
ARM: dts: stm32: add ethernet1/2 RMII pins for STM32MP13F-DK board
ARM: dts: stm32: add ethernet1 and ethernet2 support on stm32mp13
ARM: dts: stm32: Document output pins for PWMs on stm32mp135f-dk
ARM: dts: stm32: OP-TEE async notif interrupt for ST STM32MP15x boards
ARM: dts: stm32: Missing clocks for stm32f429's syscfg.
ARM: dts: stm32: Add support for STM32MP13xx DHCOR SoM and DHSBC board
ARM: dts: stm32: Add pinmux nodes for DH electronics STM32MP13xx DHCOR SoM and DHSBC board
dt-bindings: arm: stm32: Add compatible string for DH electronics STM32MP13xx DHCOR DHSBC board
ARM: dts: stm32: osd32: move pwr_regulators to common
...
Link: https://lore.kernel.org/r/8f10bd29-d067-4060-89ff-2e1a605f3141@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Allwinner SoC device tree changes for 6.11
This includes a commit shared with the clk tree. This commit adds clock
and reset indices to the device tree binding, and thus is needed for
both the device tree and driver changes.
ARM64 device tree and binding-only changes
- Add LRADC (low resolution ADC for resistor network based keys) for H616 SoC
- Add cache information for A64, H6, and H616 SoCs
- Correct model names and descriptions for Pine64 boards
- Add GPADC (general purpose ADC) for H616 SoC
- Add ADC joysticks based on GPADC for anbernic-rg35xx-h board
- Add additional CPU OPPs for the H700 on top of existing H616 ones
- Enable DVFS for rg35xx boards
- Add IOMMU for H616 SoC
RISC-V device tree changes
- Add system LDOs to D1s/T113 SoC
- Add ClockworkPi and DevTerm device trees
* tag 'sunxi-dt-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
riscv: dts: allwinner: Add ClockworkPi and DevTerm devicetrees
riscv: dts: allwinner: d1s-t113: Add system LDOs
arm64: dts: allwinner: h616: add IOMMU node
arm64: dts: allwinner: rg35xx: Enable DVFS CPU frequency scaling
arm64: dts: allwinner: h616: add additional CPU OPPs for the H700
arm64: dts: allwinner: anbernic-rg35xx-h: Add ADC joysticks
arm64: dts: allwinner: h616: Add GPADC device node
dt-bindings: clock: sun50i-h616-ccu: Add GPADC clocks
ARM: dts: sunxi: remove duplicated entries in makefile
arm64: dts: allwinner: Add cache information to the SoC dtsi for H616
arm64: dts: allwinner: Add cache information to the SoC dtsi for A64
arm64: dts: allwinner: Correct the model names for Pine64 boards
dt-bindings: arm: sunxi: Correct the descriptions for Pine64 boards
arm64: dts: allwinner: Add cache information to the SoC dtsi for H6
ARM: dts: sun50i: Add LRADC node
dt-bindings: input: sun4i-lradc-keys: Add H616 compatible
Link: https://lore.kernel.org/r/ZoQa8r1N8yi7FlPV@wens.tw
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX DT bindings for 6.11:
- Add compatible string for various new boards
- Drop Li Yang as maintainer for bindings as his email bounces
* tag 'imx-bindings-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: arm: fsl: document Kontron SMARC-sAMX6i boards
dt-bindings: arm: add MBa8MP-RAS314 SBC
dt-bindings: arm: fsl: add i.MX93 9x9 QSB board
dt-bindings: arm: fsl: add i.MX95 19x19 EVK board
dt-bindings: arm: fsl: Document Compulab IOT-GATE-iMX8
dt-bindings: Drop Li Yang as maintainer for all bindings
Link: https://lore.kernel.org/r/20240702142153.413061-2-shawnguo2@yeah.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add bindings for the SolidRun CN9132 COM-Express Type 7 evaluation board.
The CEX is based on CN9130 SoC and includes two southbridges.
Because CN9132 and 9131 are just names for different designs around the
same SoC, no soc compatibles beside marvell,cn9130 are needed.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add bindings for SolidRun boards based on CN9130 SoM.
Three boards are added in total:
- Clearfog Base
- Clearfog Pro
- SolidWAN
The Clearfog boards are identical to the older Armada 388 based boards,
upgraded with a new SoM and SoC.
However the feature set and performance characteristics are different,
therefore compatible strings from armada 388 versions are not included.
SolidWAN uses the same SoM adding a southbridge on the carrier.
Since 2019 there are bindings in-tree for two boards based on cn9130 and
9131. These are extremely verbose by listing cn9132, cn9131, cn9130,
ap807-quad, ap807 for the SoC alone.
CN9130 SoC combines an application processor (ap807) and a
communication processor (cp115) in a single package.
The communication processor (short CP) is also available separately as a
southbridge. It only functions in combination with the CN9130 SoC.
Complete systems adding one or two southbridges are by convention called
CN9131 and CN9132 respectively.
Despite different naming all systems are built around the same SoC.
Therefore marvell,cn9131 and marvell,cn9132 can be omitted. The number
of CPs is part of a board's BoM and can be reflected in the board
compatible string instead.
Existing bindings also describe cn9130 as a specialisation of
ap807-quad. Usually board-level compatibles stop at the SoC without
going into silicon versions or individual dies.
There is no programming model at this layer, and in particular not for
parts of an SoC. Therefore the ap compatibles can also be omitted.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
New boards, the Radxa ROCK S0, Radxa ZERO 3W/3E, CM3588 NAS solution
and Neardi LBA3368.
Interesting core changes: dropping of the rk3399pro dtsi - Dragan dug
through available information, boards and found out that the pcie-stuff
described in the existing rk3399pro dtsi is actually not true and the
file can go away.
And also a bit of reorganizing of rk3588 dtsi files. There are number
of rk3588 variants in existence that select between two sets of
peripherals and also multiple sets of operating points. So the change
sorts it differently so that we stop including one soc-variant into
others and also make room for the operating points.
The rk3308 got io domains, a number of additions to the rk3308-rock-pi-s
board (wifi, io-domains, otp, ethernet, uart, sdmmc).
And then there are of course the usual set of new additions like
rk3588 pcie endpoint support and individual peripherals for boards.
* tag 'v6.11-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (42 commits)
arm64: dts: rockchip: Delete the SoC variant dtsi for RK3399Pro
arm64: dts: rockchip: Fix mic-in-differential usage on rk3568-evb1-v10
arm64: dts: rockchip: Fix mic-in-differential usage on rk3566-roc-pc
arm64: dts: rockchip: Drop invalid mic-in-differential on rk3568-rock-3a
arm64: dts: rockchip: Add rock5b overlays for PCIe endpoint mode
arm64: dts: rockchip: Add PCIe endpoint mode support
arm64: dts: rockchip: Increase VOP clk rate on RK3328
arm64: dts: rockchip: add gpio-line-names to radxa-zero-3
arm64: dts: rockchip: Split GPU OPPs of RK3588 and RK3588j
arm64: dts: rockchip: Add OPP data for CPU cores on RK3588j
arm64: dts: rockchip: Add OPP data for CPU cores on RK3588
arm64: dts: rockchip: Add CPU/memory regulator coupling for 2 RK3588 boards
arm64: dts: rockchip: fix mmc aliases for Radxa ZERO 3E/3W
arm64: dts: rockchip: Add Neardi LBA3368 board
dt-bindings: arm: rockchip: Add Neardi LBA3368
dt-bindings: vendor-prefixes: Add Neardi Technology
arm64: dts: rockchip: Enable PinePhone Pro vibrator
arm64: dts: rockchip: Enable PinePhone Pro IMU sensor
arm64: dts: rockchip: Add Pinephone Pro support for GPIO LEDs
arm64: dts: rockchip: Enable SPI flash on PinePhone Pro
...
Link: https://lore.kernel.org/r/4901395.GXAFRqVoOG@diego
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
MediaTek ARM64 DTS updates for v6.11
This introduces the new Airoha (MediaTek) EN7581 home networking
platform (routers) in early stages, but with support for its
Evaluation Board, a few more MediaTek based machines, and
improvements for existing ones.
For the MT7981 router SoC we get pinctrl support, along with the
enablement of its watchdog, eFuse/nvmem, I2C and integrated WiFi
controller, other than the introduction of new machines based on
this chip: the Cudy WR3000 V1 router and the OpenWRT One.
MT7986 gets a new machine: the BananaPi R3 Mini.
Some advancements have been done also on the MT7988 SoC, which
gains support for its I2C, PWM and USB XHCI controllers.
MediaTek Genio SoCs also get attention, with the introduction of a
basic device tree for the MT8390 Genio 700-EVK board, and for the
MT8395 Genio 1200 powered Kontron 3.5"-SBC-i1200.
Additionally, the Genio 1200 Radxa NIO12L board gets support for
USB Role Switching and proper PCI-Express controller PM suspend
and resume, other than finally enabling CPU and GPU frequency
and voltage scaling for improved efficiency.
Speaking of MediaTek Kompanio SoCs (Chromebooks) instead, thanks
to community interest and help in testing, there comes support for
the MT8195-powered HP Chromebook X360 13b-ca0002sa, while Google
contributed support for the MT8186-powered Acer Chromebook 311.
Moreover, MT8188 gets support for its integrated power domains,
other than its Global Command Engine (GCE) mailboxes, initial
basic support for the VDO0/1 blocks for multimedia, and its GPU
(ARM Mali G57-MC3, Valhall-JM) with Panfrost.
Besides that, this also adds a few other cleanups and improvements
for all machines using the MT8183, MT8192, MT8195/MT8395 SoCs and
adds generation of symbols on base devicetrees of machines using
Device Tree Overlay(s) (DTBO).
In particular:
- The MediaTek Smart Voltage Scaling (SVS) is now fully working
those SoCs, bringing further power efficiency improvements;
- Thermal zones were refactored on MT8183 for consistency with
the other MediaTek SoCs and for readability
- Sound DAI links are now consistently specified in device tree
on MT8195 and MT8186 machines
- Newly supported machines/boards
- EN7581: EVK
- MT7981: Cudy WR3000 V1, OpenWRT One
- MT7986: BananaPi R3 Mini
- MT8186: Acer Chromebook 311 (Corsola Voltorb)
- MT8195: HP Chromebook X360 13b-ca0002sa (Cherry Dojo)
- MT8390/8188: Genio 700 EVK
- Some cleanups for unused/legacy devicetree properties
* tag 'mtk-dts64-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux: (58 commits)
arm64: dts: mediatek: Declare drive-strength numerically
arm64: dts: mt7622: fix switch probe on bananapi-r64
arm64: dts: mediatek: Add MT8186 Voltorb Chromebooks
dt-bindings: arm: mediatek: Add MT8186 Voltorb Chromebooks
arm64: dts: mediatek: Makefile: Generate symbols for DTBO support
arm64: dts: mediatek: mt8183-kukui-jacuzzi: Add ports node for anx7625
arm64: dts: mediatek: mt8183-pico6: Fix wake-on-X event node names
arm64: dts: mt8173: Add G2Touch touchscreen node
arm64: dts: mediatek: mt8183-kukui: Fix the value of `dlg,jack-det-rate` mismatch
arm64: dts: mediatek: mt8188: Add support for Mali GPU on Panfrost
arm64: dts: mediatek: mt8188: Add support for SoC power domains
arm64: dts: mediatek: mt8188: Add VDOSYS0/1 support for multimedia
arm64: dts: mediatek: mt8188: Add Global Command Engine mailboxes
arm64: dts: mediatek: mt8173-elm: drop PMIC's syscon node
arm64: dts: mediatek: mt8365: use a specific SCPSYS compatible
arm64: dts: mediatek: mt8365: drop incorrect power-domain-cells
arm64: dts: mediatek: mt7981: add I2C controller
arm64: dts: mediatek: mt7622: fix "emmc" pinctrl mux
arm64: dts: mediatek: mt7988: add I2C controllers
arm64: dts: mediatek: mt7988: add PWM controller
...
Link: https://lore.kernel.org/r/20240628093801.126013-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arm Vexpress updates for v6.11
Remove obsolete RTSM DCSCB support which was only ever implemented
on a software model which is neither available to download nor
maintained. It predates the very first bL cluster based platforms.
Other change include addition of the missing MODULE_DESCRIPTION
macro in vexpress config bus driver.
* tag 'vexpress-updates-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
bus: vexpress-config: Add missing MODULE_DESCRIPTION() macro
dt-bindings: arm: Remove obsolete RTSM DCSCB binding
arm: vexpress: Remove obsolete RTSM DCSCB support
Link: https://lore.kernel.org/r/20240620093924.375244-4-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arm Juno updates for v6.11
Addition of dedicated FPGA syscon compatible for Juno platforms. Also
enablement of GPU device node now that the panfrost driver is already
enabled as a module in defconfig.
* tag 'juno-updates-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: Enable GPU
arm64: dts: juno: add dedicated FPGA syscon compatible
dt-bindings: arm: arm,juno-fpga-apb-regs: document FPGA syscon
Link: https://lore.kernel.org/r/20240620093924.375244-2-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Kontron SMARC-sAMX6i is just a module. There was no device tree for
an actual board for now. Document the binding to use the module on the
evaluation carrier.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
MBa8MP-RAS314 is an SBC based on the embedded module TQMa8MPxL.
All relevant interfaces integrated in the CPU have been implemented on
the MBa8MP-RAS314 for (an) industrial usage. Due to the numerous interfaces
and the small size of this SBC the use in different applications
is possible without the need of a [special,custom] design.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
