The Cypress cy15b104q and cy15v104q are 4Mbit serial SPI F-RAM devices.
Add support for them to the spi-nor driver.
The actual Device ID of this chip is 7f 7f 7f 7f 7f 7f c2 2c 04. That is
six times the continuation code 7f followed by c2 for Ramtron.
Unfortunately the chip sends the Device ID in reversed order, so the
continuation code is not at the beginning, but instead at the end. Even
more unfortunate is that when reading further the chip sends more 7f
codes which means we are not even able to count the continuation codes.
We can only hope that this reversed Device ID will never match any other
devices ID.
Collisions are improbable as of now, the solution from above is good
enough. In case of future collisions one can introduce an INFO9 macro,
with the downsize that struct flash_info would grow and we have lots of
flashes. A more elegant solution would be to introduce dedicated
flash ID tables for each bank in JESP106BA.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[tudor.ambarus@microchip.com: amend commit description with possible
future solutions in case collisions occur.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
s25fs256s was identified as s25fl256s. Differentiate between them by
the Family ID using the INFO6 macro.
Fixes: b199489d37 ("mtd: spi-nor: add the framework for SPI NOR")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Add support for Cypress s25fs128s1 flash. Previously the flash is
decoded as s25fl129p1 by mistake.
Add it in the flash info list to correctly decode. The flash also
needs a fixup for s25fs-s family. Further capability of the flash will
be parsed from bfpt.
The flash has been tested under SPI/DUAL/QUAD mode on hisi-sfc-v3xx
controller, all the write/read/erase works well.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Spansion S25FS-S family has an issue in the Basic Flash Parameter Table
(BFPT): Dword-11 bits 7:4 specify a page size of 512 bytes. Actually
this is configurable in the vendor unique register (CR3V) and even the
factory default setting is to "wrap at 256 bytes", so blindly relying
on BFPT breaks the page writes on these chips. Add the post-BFPT fixup
which restores the default page size of 256 bytes -- to properly read
CR3V this early is quite intrusive and should better be done as a new
feature; Alexander Sverdlin had the patch doing that:
https://patchwork.ozlabs.org/project/linux-mtd/patch/20200227123657.26030-1-alexander.sverdlin@nokia.com/
Fixes: dfd2b74530 ("mtd: spi-nor: add Spansion S25FS512S ID")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add support for the hardware ECC BCH engine.
Please mind that this engine has an important limitation:
BCH implementation does not inform the user when an uncorrectable ECC
error occurs. To workaround this, we avoid using the hardware engine
in the read path and do the computation with the software BCH
implementation, which is faster than mixing hardware (for correction)
and software (for verification).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200519074549.23673-9-miquel.raynal@bootlin.com
It seems that several hardware ECC engine use a swapped representation
of bytes compared to software. This might having to do with how the
ECC engine is wired to the NAND controller or the order the bits are
passed to the hardware BCH logic.
This means that when the software BCH engine is working in conjunction
with data generated with hardware, sometimes we might need to swap the
bits inside bytes, eg:
0x0A = b0000_1010 -> b0101_0000 = 0x50
Make it possible by adding a boolean to the BCH initialization routine.
Regarding the implementation itself, this is a rather simple approach
that can probably be enhanced in the future by preparing the
->a_{mod,pow}_tab tables with the swapping in mind.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200519074549.23673-3-miquel.raynal@bootlin.com
There are controllers not able to just read data cycles on the
bus. There are controllers not able to do a change column.
If we want to support both, we need to check which operation is
supported first. This is the exact same mechanism that is in use for
parameter page reads (ONFI/JEDEC) as the same problem occurs.
Speed testing does not show any throughput penalty so we do not
optimize more than that. However it is likely that, in the future, a
more robust and exhaustive test will run at boot time to avoid
re-checking what is supported and what is not at every call.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200519130834.2918-1-miquel.raynal@bootlin.com
The current code checks that the whole OOB area is erased.
This is a problem when JFFS2 cleanmarkers are added to the OOB, since it will
fail due to the usable OOB bytes not being 0xff.
Correct this by only checking that data and ECC bytes aren't 0xff.
Fixes: 02b88eea9f ("mtd: brcmnand: Add check for erased page bitflips")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200512082451.771212-1-noltari@gmail.com
Pull MTD fixes from Richard Weinberger:
- Fix a PM regression in brcmnand driver
- Propagate ECC information correctly on SPI-NAND
- Make sure no MTD name is used multiple time in nvmem
* tag 'fixes-for-5.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd:rawnand: brcmnand: Fix PM resume crash
mtd: Fix mtd not registered due to nvmem name collision
mtd: spinand: Propagate ECC information to the MTD structure
Pull UBI and UBIFS fixes from Richard Weinberger:
- Correctly set next cursor for detailed_erase_block_info debugfs file
- Don't use crypto_shash_descsize() for digest size in UBIFS
- Remove broken lazytime support from UBIFS
* tag 'for-linus-5.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubi: Fix seq_file usage in detailed_erase_block_info debugfs file
ubifs: fix wrong use of crypto_shash_descsize()
ubifs: remove broken lazytime support
This change fixes crash observed on PM resume. This bug
was introduced in the change made for flash-edu support.
Fixes: a5d53ad26a ("mtd: rawnand: brcmnand: Add support for flash-edu for dma transfers")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
When the nvmem framework is enabled, a nvmem device is created per mtd
device/partition.
It is not uncommon that a device can have multiple mtd devices with
partitions that have the same name. Eg, when there DT overlay is allowed
and the same device with mtd is attached twice.
Under that circumstances, the mtd fails to register due to a name
duplication on the nvmem framework.
With this patch we use the mtdX name instead of the partition name,
which is unique.
[ 8.948991] sysfs: cannot create duplicate filename '/bus/nvmem/devices/Production Data'
[ 8.948992] CPU: 7 PID: 246 Comm: systemd-udevd Not tainted 5.5.0-qtec-standard #13
[ 8.948993] Hardware name: AMD Dibbler/Dibbler, BIOS 05.22.04.0019 10/26/2019
[ 8.948994] Call Trace:
[ 8.948996] dump_stack+0x50/0x70
[ 8.948998] sysfs_warn_dup.cold+0x17/0x2d
[ 8.949000] sysfs_do_create_link_sd.isra.0+0xc2/0xd0
[ 8.949002] bus_add_device+0x74/0x140
[ 8.949004] device_add+0x34b/0x850
[ 8.949006] nvmem_register.part.0+0x1bf/0x640
...
[ 8.948926] mtd mtd8: Failed to register NVMEM device
Fixes: c4dfa25ab3 ("mtd: add support for reading MTD devices via the nvmem API")
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
This is done by default in the raw NAND core (nand_base.c) but was
missing in the SPI-NAND core. Without these two lines the ecc_strength
and ecc_step_size values are not exported to the user through sysfs.
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
3bfa7e141b ("fs/seq_file.c: seq_read(): add info message about buggy .next functions")
showed that we don't use seq_file correctly.
So make sure that our ->next function always updates the position.
Fixes: 7bccd12d27 ("ubi: Add debugfs file for tracking PEB state")
Signed-off-by: Richard Weinberger <richard@nod.at>
This patch removes the constant FMC2_TIMEOUT_US.
FMC2_TIMEOUT_MS will be used each time that we need to wait (except
when the timeout value is set by the framework).
It was seen, during stress tests with the sequencer in an overloaded
system, that we could be close to 1 second, even if we never met this
value. To be safe, FMC2_TIMEOUT_MS is set to 5 seconds.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1588756279-17289-4-git-send-email-christophe.kerello@st.com
Implement exec_op() so we can later get rid of the legacy
implementation.
It's worth noting that the new implementation assert/deassert the CE
pin on each operation, which might not be necessary. We also dropped
the extra reset done at chip selection time on DOC2001plus. If it's
needed we really should do something smarter, because having a reset
everytime we access the chip is not that great perf-wise.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200501143917.1388957-5-boris.brezillon@collabora.com
We already know that there are controllers not able to read the three
copies of the parameter page in one go. The workaround was to first
request the controller to assert command and address cycles on the
NAND bus to trigger a parameter page read, and then do a read
operation for each page.
But there are also controllers which are not able to split the
parameter page read between the command/address cycles and the actual
data operation.
Let's use a regular PARAMETER PAGE READ operation for the first
iteration and use eithe a CHANGE READ COLUMN or a simple DATA READ
operation for the following copies, depending on what the controller
supports. The default for non-exec-op compliant drivers remains
unchanged: use a SIMPLE READ.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-11-miquel.raynal@bootlin.com
We already know that there are controllers not able to read the three
copies of the parameter page in one go. The workaround was to first
request the controller to assert command and address cycles on the
NAND bus to trigger a parameter page read, and then do a simple read
operation for each page.
But there are also controllers which are not able to split the
parameter page read between the command/address cycles and the actual
data operation.
Let's use a regular PARAMETER PAGE READ operation for the first
iteration and use either a CHANGE READ COLUMN or a simple DATA READ
operation for the following copies, depending on what the controller
supports. The default behavior for non-exec-op compliant drivers
remains the same: DATA READ.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-10-miquel.raynal@bootlin.com
The logic in nand_do_read_ops() is to use a bufpoi variable, either
set to the original buffer, or set to a bounce buffer which in the end
happens to be chip->data_buf depending on the value of the
use_bounce_buf boolean. This is not a reason to call chip->data_buf
directly when we know that we are using the bounce buffer. Let's use
bufpoi instead to be consistent.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-7-miquel.raynal@bootlin.com
