The stmmac platform drivers that do not open-code the clk_ptp_rate value
after having retrieved the default one from the device-tree can end up
with 0 in clk_ptp_rate (as clk_get_rate can return 0). It will
eventually propagate up to PTP initialization when bringing up the
interface, leading to a divide by 0:
Division by zero in kernel.
CPU: 1 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.30-00001-g48313bd5768a #22
Hardware name: STM32 (Device Tree Support)
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x6c/0x8c
dump_stack_lvl from Ldiv0_64+0x8/0x18
Ldiv0_64 from stmmac_init_tstamp_counter+0x190/0x1a4
stmmac_init_tstamp_counter from stmmac_hw_setup+0xc1c/0x111c
stmmac_hw_setup from __stmmac_open+0x18c/0x434
__stmmac_open from stmmac_open+0x3c/0xbc
stmmac_open from __dev_open+0xf4/0x1ac
__dev_open from __dev_change_flags+0x1cc/0x224
__dev_change_flags from dev_change_flags+0x24/0x60
dev_change_flags from ip_auto_config+0x2e8/0x11a0
ip_auto_config from do_one_initcall+0x84/0x33c
do_one_initcall from kernel_init_freeable+0x1b8/0x214
kernel_init_freeable from kernel_init+0x24/0x140
kernel_init from ret_from_fork+0x14/0x28
Exception stack(0xe0815fb0 to 0xe0815ff8)
Prevent this division by 0 by adding an explicit check and error log
about the actual issue. While at it, remove the same check from
stmmac_ptp_register, which then becomes duplicate
Fixes: 19d857c903 ("stmmac: Fix calculations for ptp counters when clock input = 50Mhz.")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250529-stmmac_tstamp_div-v4-1-d73340a794d5@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MANA driver's probe registers netdevice via the following call chain:
mana_probe()
register_netdev()
register_netdevice()
register_netdevice() calls notifier callback for netvsc driver,
holding the netdev mutex via netdev_lock_ops().
Further this netvsc notifier callback end up attempting to acquire the
same lock again in dev_xdp_propagate() leading to deadlock.
netvsc_netdev_event()
netvsc_vf_setxdp()
dev_xdp_propagate()
This deadlock was not observed so far because net_shaper_ops was never set,
and thus the lock was effectively a no-op in this case. Fix this by using
netif_xdp_propagate() instead of dev_xdp_propagate() to avoid recursive
locking in this path.
And, since no deadlock is observed on the other path which is via
netvsc_probe, add the lock exclusivly for that path.
Also, clean up the unregistration path by removing the unnecessary call to
netvsc_vf_setxdp(), since unregister_netdevice_many_notify() already
performs this cleanup via dev_xdp_uninstall().
Fixes: 97246d6d21 ("net: hold netdev instance lock during ndo_bpf")
Cc: stable@vger.kernel.org
Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Tested-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://patch.msgid.link/1748513910-23963-1-git-send-email-ssengar@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- hci_qca: move the SoC type check to the right place
- MGMT: reject malformed HCI_CMD_SYNC commands
- btnxpuart: Fix missing devm_request_irq() return value check
- L2CAP: Fix not responding with L2CAP_CR_LE_ENCRYPTION
* tag 'for-net-2025-05-30' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: L2CAP: Fix not responding with L2CAP_CR_LE_ENCRYPTION
Bluetooth: hci_qca: move the SoC type check to the right place
Bluetooth: btnxpuart: Fix missing devm_request_irq() return value check
Bluetooth: MGMT: reject malformed HCI_CMD_SYNC commands
====================
Link: https://patch.msgid.link/20250530174835.405726-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The default idle selection policy doesn't properly handle the case where
@prev_cpu is not part of the task's allowed CPUs.
In this situation, it may return an idle CPU that is not usable by the
task, breaking the assumption that the returned CPU must always be
within the allowed cpumask, causing inefficiencies or even stalls in
certain cases.
This issue can arise in the following cases:
- The task's affinity may have changed by the time the function is
invoked, especially now that the idle selection logic can be used
from multiple contexts (i.e., BPF test_run call).
- The BPF scheduler may provide a @prev_cpu that is not part of the
allowed mask, either unintentionally or as a placement hint. In fact
@prev_cpu may not necessarily refer to the CPU the task last ran on,
but it can also be considered as a target CPU that the scheduler
wishes to use for the task.
Therefore, enforce the right behavior by always checking whether
@prev_cpu is in the allowed mask, when using scx_bpf_select_cpu_and(),
and it's also usable by the task (@p->cpus_ptr). If it is not, try to
find a valid CPU nearby @prev_cpu, following the usual locality-aware
fallback path (SMT, LLC, node, allowed CPUs).
This ensures the returned CPU is always allowed, improving robustness to
affinity changes and invalid scheduler hints, while preserving locality
as much as possible.
Fixes: a730e3f7a4 ("sched_ext: idle: Consolidate default idle CPU selection kfuncs")
Signed-off-by: Andrea Righi <arighi@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Previously it was found that on uniprocessor machines the size of
raw_spinlock_t could be zero so a pre-processor conditional was used to
avoid the allocation of ss->rstat_ss_cpu_lock. The conditional did not take
into account cases where lock debugging features were enabled. Cover these
cases along with the original non-smp case by explicitly using the size of
size of the lock type as criteria for allocation/access where applicable.
Signed-off-by: JP Kobryn <inwardvessel@gmail.com>
Fixes: 748922dcfa "cgroup: use subsystem-specific rstat locks to avoid contention"
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202505281034.7ae1668d-lkp@intel.com
Reviewed-by: Shakeel Butt <shakeel.butt@linux.dev>
Reviewed-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When enabling PREEMPT_RT, the gpio_keys_irq_timer() callback runs in
hard irq context, but the input_event() takes a spin_lock, which isn't
allowed there as it is converted to a rt_spin_lock().
[ 4054.289999] BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
[ 4054.290028] in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 0, name: swapper/0
...
[ 4054.290195] __might_resched+0x13c/0x1f4
[ 4054.290209] rt_spin_lock+0x54/0x11c
[ 4054.290219] input_event+0x48/0x80
[ 4054.290230] gpio_keys_irq_timer+0x4c/0x78
[ 4054.290243] __hrtimer_run_queues+0x1a4/0x438
[ 4054.290257] hrtimer_interrupt+0xe4/0x240
[ 4054.290269] arch_timer_handler_phys+0x2c/0x44
[ 4054.290283] handle_percpu_devid_irq+0x8c/0x14c
[ 4054.290297] handle_irq_desc+0x40/0x58
[ 4054.290307] generic_handle_domain_irq+0x1c/0x28
[ 4054.290316] gic_handle_irq+0x44/0xcc
Considering the gpio_keys_irq_isr() can run in any context, e.g. it can
be threaded, it seems there's no point in requesting the timer isr to
run in hard irq context.
Relax the hrtimer not to use the hard context.
Fixes: 019002f20c ("Input: gpio-keys - use hrtimer for release timer")
Suggested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Link: https://lore.kernel.org/r/20250528-gpio_keys_preempt_rt-v2-1-3fc55a9c3619@foss.st.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull automount updates from Al Viro:
"Automount wart removal
A bunch of odd boilerplate gone from instances - the reason for
those was the need to protect the yet-to-be-attched mount from
mark_mounts_for_expiry() deciding to take it out.
But that's easy to detect and take care of in mark_mounts_for_expiry()
itself; no need to have every instance simulate mount being busy by
grabbing an extra reference to it, with finish_automount() undoing
that once it attaches that mount.
Should've done it that way from the very beginning... This is a
flagday change, thankfully there are very few instances.
vfs_submount() is gone - its sole remaining user (trace_automount)
had been switched to saner primitives"
* tag 'pull-automount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
kill vfs_submount()
saner calling conventions for ->d_automount()
Pull UFS updates from Al Viro:
"The bulk of this is Eric's conversion of UFS to new mount API, with a
bit of cleanups from me. I hoped to get stricter sanity checks on
superblock flags into that pile, but... next cycle, hopefully"
* tag 'pull-ufs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ufs: convert ufs to the new mount API
ufs: reject multiple conflicting -o ufstype=... on mount
ufs: split ->s_mount_opt - don't mix flavour and on-error
Pull mount propagation fix from Al Viro:
"6.15 allowed mount propagation to destinations in detached trees;
unfortunately, that breaks existing userland, so the old behaviour
needs to be restored.
It's not exactly a revert - the original behaviour had a bug, where
existence of detached tree might disrupt propagation between locations
not in detached trees. Thankfully, userland did not depend upon that
bug, so we want to keep the fix"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Don't propagate mounts into detached trees
The XE driver can be built with or without VSEC support, but fails to link as
built-in if vsec is in a loadable module:
x86_64-linux-ld: vmlinux.o: in function `xe_vsec_init':
(.text+0x1e83e16): undefined reference to `intel_vsec_register'
The normal fix for this is to add a 'depends on INTEL_VSEC || !INTEL_VSEC',
forcing XE to be a loadable module as well, but that causes a circular
dependency:
symbol DRM_XE depends on INTEL_VSEC
symbol INTEL_VSEC depends on X86_PLATFORM_DEVICES
symbol X86_PLATFORM_DEVICES is selected by DRM_XE
The problem here is selecting a symbol from another subsystem, so change
that as well and rephrase the 'select' into the corresponding dependency.
Since X86_PLATFORM_DEVICES is 'default y', there is no change to
defconfig builds here.
Fixes: 0c45e76fcc ("drm/xe/vsec: Support BMG devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250529172355.2395634-2-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Mailbox operations are not possible while the driver is in reset.
Operations that require MBX exchange with the control plane will result
in long delays if executed while a reset is in progress:
ethtool -L <inf> combined 8& echo 1 > /sys/class/net/<inf>/device/reset
idpf 0000:83:00.0: HW reset detected
idpf 0000:83:00.0: Device HW Reset initiated
idpf 0000:83:00.0: Transaction timed-out (op:504 cookie:be00 vc_op:504 salt:be timeout:2000ms)
idpf 0000:83:00.0: Transaction timed-out (op:508 cookie:bf00 vc_op:508 salt:bf timeout:2000ms)
idpf 0000:83:00.0: Transaction timed-out (op:512 cookie:c000 vc_op:512 salt:c0 timeout:2000ms)
idpf 0000:83:00.0: Transaction timed-out (op:510 cookie:c100 vc_op:510 salt:c1 timeout:2000ms)
idpf 0000:83:00.0: Transaction timed-out (op:509 cookie:c200 vc_op:509 salt:c2 timeout:60000ms)
idpf 0000:83:00.0: Transaction timed-out (op:509 cookie:c300 vc_op:509 salt:c3 timeout:60000ms)
idpf 0000:83:00.0: Transaction timed-out (op:505 cookie:c400 vc_op:505 salt:c4 timeout:60000ms)
idpf 0000:83:00.0: Failed to configure queues for vport 0, -62
Disable mailbox communication in case of a reset, unless it's done during
a driver load, where the virtchnl operations are needed to configure the
device.
Fixes: 8077c72756 ("idpf: add controlq init and reset checks")
Co-developed-by: Joshua Hay <joshua.a.hay@intel.com>
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reviewed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a helper function to correctly handle the lockless
synchronization when the sender needs to block. The paradigm is
if (no_resources()) {
stop_queue();
barrier();
if (!no_resources())
restart_queue();
}
netif_subqueue_maybe_stop already handles the paradigm correctly, but
the code split the check for resources in three parts, the first one
(descriptors) followed the protocol, but the other two (completions and
tx_buf) were only doing the first part and so race prone.
Luckily netif_subqueue_maybe_stop macro already allows you to use a
function to evaluate the start/stop conditions so the fix only requires
the right helper function to evaluate all the conditions at once.
The patch removes idpf_tx_maybe_stop_common since it's no longer needed
and instead adjusts separately the conditions for singleq and splitq.
Note that idpf_tx_buf_hw_update doesn't need to check for resources
since that will be covered in idpf_tx_splitq_frame.
To reproduce:
Reduce the threshold for pending completions to increase the chances of
hitting this pause by changing your kernel:
drivers/net/ethernet/intel/idpf/idpf_txrx.h
-#define IDPF_TX_COMPLQ_OVERFLOW_THRESH(txcq) ((txcq)->desc_count >> 1)
+#define IDPF_TX_COMPLQ_OVERFLOW_THRESH(txcq) ((txcq)->desc_count >> 4)
Use pktgen to force the host to push small pkts very aggressively:
./pktgen_sample02_multiqueue.sh -i eth1 -s 100 -6 -d $IP -m $MAC \
-p 10000-10000 -t 16 -n 0 -v -x -c 64
Fixes: 6818c4d5b3 ("idpf: add splitq start_xmit")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Luigi Rizzo <lrizzo@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The current implementation of the Tx scheduler allows the tree to be
rebuilt as the user adds more Tx queues to the VSI. In such a case,
additional child nodes are added to the tree to support the new number
of queues.
Unfortunately, this algorithm does not take into account that the limit
of the VSI support node may be exceeded, so an additional node in the
VSI layer may be required to handle all the requested queues.
Such a scenario occurs when adding XDP Tx queues on machines with many
CPUs. Although the driver still respects the queue limit returned by
the FW, the Tx scheduler was unable to add those queues to its tree
and returned one of the errors below.
Such a scenario occurs when adding XDP Tx queues on machines with many
CPUs (e.g. at least 321 CPUs, if there is already 128 Tx/Rx queue pairs).
Although the driver still respects the queue limit returned by the FW,
the Tx scheduler was unable to add those queues to its tree and returned
the following errors:
Failed VSI LAN queue config for XDP, error: -5
or:
Failed to set LAN Tx queue context, error: -22
Fix this problem by extending the tree rebuild algorithm to check if the
current VSI node can support the requested number of queues. If it
cannot, create as many additional VSI support nodes as necessary to
handle all the required Tx queues. Symmetrically, adjust the VSI node
removal algorithm to remove all nodes associated with the given VSI.
Also, make the search for the next free VSI node more restrictive. That is,
add queue group nodes only to the VSI support nodes that have a matching
VSI handle.
Finally, fix the comment describing the tree update algorithm to better
reflect the current scenario.
Fixes: b0153fdd7e ("ice: update VSI config dynamically")
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Jesse Brandeburg <jbrandeburg@cloudflare.com>
Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The current implementation of the Tx scheduler tree attempts
to create nodes for all Tx queues, ignoring the fact that some
queues may already exist in the tree. For example, if the VSI
already has 128 Tx queues and the user requests for 16 new queues,
the Tx scheduler will compute the tree for 272 queues (128 existing
queues + 144 new queues), instead of 144 queues (128 existing queues
and 16 new queues).
Fix that by modifying the node count calculation algorithm to skip
the queues that already exist in the tree.
Fixes: 5513b920a4 ("ice: Update Tx scheduler tree for VSI multi-Tx queue support")
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Jesse Brandeburg <jbrandeburg@cloudflare.com>
Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the XDP program is loaded, the XDP callback adds new Tx queues.
This means that the callback must update the Tx scheduler with the new
queue number. In the event of a Tx scheduler failure, the XDP callback
should also fail and roll back any changes previously made for XDP
preparation.
The previous implementation had a bug that not all changes made by the
XDP callback were rolled back. This caused the crash with the following
call trace:
[ +9.549584] ice 0000:ca:00.0: Failed VSI LAN queue config for XDP, error: -5
[ +0.382335] Oops: general protection fault, probably for non-canonical address 0x50a2250a90495525: 0000 [#1] SMP NOPTI
[ +0.010710] CPU: 103 UID: 0 PID: 0 Comm: swapper/103 Not tainted 6.14.0-net-next-mar-31+ #14 PREEMPT(voluntary)
[ +0.010175] Hardware name: Intel Corporation M50CYP2SBSTD/M50CYP2SBSTD, BIOS SE5C620.86B.01.01.0005.2202160810 02/16/2022
[ +0.010946] RIP: 0010:__ice_update_sample+0x39/0xe0 [ice]
[...]
[ +0.002715] Call Trace:
[ +0.002452] <IRQ>
[ +0.002021] ? __die_body.cold+0x19/0x29
[ +0.003922] ? die_addr+0x3c/0x60
[ +0.003319] ? exc_general_protection+0x17c/0x400
[ +0.004707] ? asm_exc_general_protection+0x26/0x30
[ +0.004879] ? __ice_update_sample+0x39/0xe0 [ice]
[ +0.004835] ice_napi_poll+0x665/0x680 [ice]
[ +0.004320] __napi_poll+0x28/0x190
[ +0.003500] net_rx_action+0x198/0x360
[ +0.003752] ? update_rq_clock+0x39/0x220
[ +0.004013] handle_softirqs+0xf1/0x340
[ +0.003840] ? sched_clock_cpu+0xf/0x1f0
[ +0.003925] __irq_exit_rcu+0xc2/0xe0
[ +0.003665] common_interrupt+0x85/0xa0
[ +0.003839] </IRQ>
[ +0.002098] <TASK>
[ +0.002106] asm_common_interrupt+0x26/0x40
[ +0.004184] RIP: 0010:cpuidle_enter_state+0xd3/0x690
Fix this by performing the missing unmapping of XDP queues from
q_vectors and setting the XDP rings pointer back to NULL after all those
queues are released.
Also, add an immediate exit from the XDP callback in case of ring
preparation failure.
Fixes: efc2214b60 ("ice: Add support for XDP")
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Jesse Brandeburg <jbrandeburg@cloudflare.com>
Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Pull EFI updates from Ard Biesheuvel:
"Not a lot going on in the EFI tree this cycle. The only thing that
stands out is the new support for SBAT metadata, which was a bit
contentious when it was first proposed, because in the initial
incarnation, it would have required us to maintain a revocation index,
and bump it each time a vulnerability affecting UEFI secure boot got
fixed. This was shot down for obvious reasons.
This time, only the changes needed to emit the SBAT section into the
PE/COFF image are being carried upstream, and it is up to the distros
to decide what to put in there when creating and signing the build.
This only has the EFI zboot bits (which the distros will be using for
arm64); the x86 bzImage changes should be arriving next cycle,
presumably via the -tip tree.
Summary:
- Add support for emitting a .sbat section into the EFI zboot image,
so that downstreams can easily include revocation metadata in the
signed EFI images
- Align PE symbolic constant names with other projects
- Bug fix for the efi_test module
- Log the physical address and size of the EFI memory map when
failing to map it
- A kerneldoc fix for the EFI stub code"
* tag 'efi-next-for-v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
include: pe.h: Fix PE definitions
efi/efi_test: Fix missing pending status update in getwakeuptime
efi: zboot specific mechanism for embedding SBAT section
efi/libstub: Describe missing 'out' parameter in efi_load_initrd
efi: Improve logging around memmap init
Pull ACPI fixes from Rafael Wysocki:
"These address issues introduced by recent ACPI changes merged
previously:
- Unbreak acpi_ut_safe_strncpy() by restoring its previous behavior
changed incorrectly by a recent update (Ahmed Salem)
- Make a new static checker warning in the recently introduced ACPI
MRRM table parser go away (Dan Carpenter)
- Fix ACPI table referece leak in error path of einj_probe() (Dan
Carpenter)"
* tag 'acpi-6.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: Switch back to using strncpy() in acpi_ut_safe_strncpy()
ACPI: MRRM: Silence error code static checker warning
ACPI: APEI: EINJ: Clean up on error in einj_probe()
Pull more power management updates from Rafael Wysocki:
"These revert an x86 commit that introduced a nasty power regression on
some systems, fix PSCI cpuidle driver and ACPI cpufreq driver
regressions, add Rust abstractions for cpufreq, OPP, clk, and
cpumasks, add a Rust-based cpufreq-dt driver, and do a minor SCMI
cpufreq driver cleanup:
- Revert an x86 commit that went into 6.15 and caused idle power,
including power in suspend-to-idle, to rise rather dramatically on
systems booting with "nosmt" in the kernel command line (Rafael
Wysocki)
- Prevent freeing an uninitialized pointer in error path of
dt_idle_state_present() in the PSCI cpuidle driver (Dan Carpenter)
- Use KHz as the nominal_freq units in get_max_boost_ratio() in the
ACPI cpufreq driver (iGautham Shenoy)
- Add Rust abstractions for CPUFreq framework (Viresh Kumar)
- Add Rust abstractions for OPP framework (Viresh Kumar)
- Add basic Rust abstractions for Clk and Cpumask frameworks (Viresh
Kumar)
- Clean up the SCMI cpufreq driver somewhat (Mike Tipton)"
* tag 'pm-6.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (21 commits)
Revert "x86/smp: Eliminate mwait_play_dead_cpuid_hint()"
acpi-cpufreq: Fix nominal_freq units to KHz in get_max_boost_ratio()
rust: opp: Move `cfg(CONFIG_OF)` attribute to the top of doc test
cpuidle: psci: Fix uninitialized variable in dt_idle_state_present()
rust: opp: Make the doctest example depend on CONFIG_OF
cpufreq: scmi: Skip SCMI devices that aren't used by the CPUs
cpufreq: Add Rust-based cpufreq-dt driver
rust: opp: Extend OPP abstractions with cpufreq support
rust: cpufreq: Extend abstractions for driver registration
rust: cpufreq: Extend abstractions for policy and driver ops
rust: cpufreq: Add initial abstractions for cpufreq framework
rust: opp: Add abstractions for the configuration options
rust: opp: Add abstractions for the OPP table
rust: opp: Add initial abstractions for OPP framework
rust: cpu: Add from_cpu()
rust: macros: enable use of hyphens in module names
rust: clk: Add initial abstractions
rust: clk: Add helpers for Rust code
MAINTAINERS: Add entry for Rust cpumask API
rust: cpumask: Add initial abstractions
...
Fix an issue in the PSCI cpuidle driver introduced recently and a nasty
x86 power regression introduced in 6.15:
- Prevent freeing an uninitialized pointer in error path of
dt_idle_state_present() in the PSCI cpuidle driver (Dan Carpenter).
- Revert an x86 commit that went into 6.15 and caused idle power,
including power in suspend-to-idle, to rise rather dramatically on
systems booting with "nosmt" in the kernel command line (Rafael Wysocki).
* pm-cpuidle:
Revert "x86/smp: Eliminate mwait_play_dead_cpuid_hint()"
cpuidle: psci: Fix uninitialized variable in dt_idle_state_present()
Merge Rust support for cpufreq and OPP, a new Rust-based cpufreq-dt
driver, an SCMI cpufreq driver cleanup, and an ACPI cpufreq driver
regression fix:
- Add Rust abstractions for CPUFreq framework (Viresh Kumar).
- Add Rust abstractions for OPP framework (Viresh Kumar).
- Add basic Rust abstractions for Clk and Cpumask frameworks (Viresh
Kumar).
- Clean up the SCMI cpufreq driver somewhat (Mike Tipton).
- Use KHz as the nominal_freq units in get_max_boost_ratio() in the
ACPI cpufreq driver (iGautham Shenoy).
* pm-cpufreq:
acpi-cpufreq: Fix nominal_freq units to KHz in get_max_boost_ratio()
rust: opp: Move `cfg(CONFIG_OF)` attribute to the top of doc test
rust: opp: Make the doctest example depend on CONFIG_OF
cpufreq: scmi: Skip SCMI devices that aren't used by the CPUs
cpufreq: Add Rust-based cpufreq-dt driver
rust: opp: Extend OPP abstractions with cpufreq support
rust: cpufreq: Extend abstractions for driver registration
rust: cpufreq: Extend abstractions for policy and driver ops
rust: cpufreq: Add initial abstractions for cpufreq framework
rust: opp: Add abstractions for the configuration options
rust: opp: Add abstractions for the OPP table
rust: opp: Add initial abstractions for OPP framework
rust: cpu: Add from_cpu()
rust: macros: enable use of hyphens in module names
rust: clk: Add initial abstractions
rust: clk: Add helpers for Rust code
MAINTAINERS: Add entry for Rust cpumask API
rust: cpumask: Add initial abstractions
rust: cpumask: Add few more helpers
Merge fixes for issues introduced by recent ACPI changes merged
previously:
- Unbreak acpi_ut_safe_strncpy() by restoring its previous behavior
changed incorrectly by a recent update (Ahmed Salem).
- Make a new static checker warning in the recently introduced ACPI
MRRM table parser go away (Dan Carpenter).
- Fix ACPI table referece leak in error path of einj_probe() (Dan
Carpenter).
* acpica:
ACPICA: Switch back to using strncpy() in acpi_ut_safe_strncpy()
* acpi-tables:
ACPI: MRRM: Silence error code static checker warning
* acpi-apei:
ACPI: APEI: EINJ: Clean up on error in einj_probe()
Pull iommu updates from Joerg Roedel:
"Core:
- Introduction of iommu-pages infrastructure to consolitate
page-table allocation code among hardware drivers. This is
ground-work for more generalization in the future
- Remove IOMMU_DEV_FEAT_SVA and IOMMU_DEV_FEAT_IOPF feature flags
- Convert virtio-iommu to domain_alloc_paging()
- KConfig cleanups
- Some small fixes for possible overflows and race conditions
Intel VT-d driver:
- Restore WO permissions on second-level paging entries
- Use ida to manage domain id
- Miscellaneous cleanups
AMD-Vi:
- Make sure notifiers finish running before module unload
- Add support for HTRangeIgnore feature
- Allow matching ACPI HID devices without matching UIDs
ARM-SMMU:
- SMMUv2:
- Recognise the compatible string for SAR2130P MDSS in the
Qualcomm driver, as this device requires an identity domain
- Fix Adreno stall handling so that GPU debugging is more robust
and doesn't e.g. result in deadlock
- SMMUv3:
- Fix ->attach_dev() error reporting for unrecognised domains
- IO-pgtable:
- Allow clients (notably, drivers that process requests from
userspace) to silence warnings when mapping an already-mapped
IOVA
S390:
- Add support for additional table regions
Mediatek:
- Add support for MT6893 MM IOMMU
And some smaller fixes and improvements in various other drivers"
* tag 'iommu-updates-v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux: (75 commits)
iommu/vt-d: Restore context entry setup order for aliased devices
iommu/mediatek: Fix compatible typo for mediatek,mt6893-iommu-mm
iommu/arm-smmu-qcom: Make set_stall work when the device is on
iommu/arm-smmu: Move handing of RESUME to the context fault handler
iommu/arm-smmu-qcom: Enable threaded IRQ for Adreno SMMUv2/MMU500
iommu/io-pgtable-arm: Add quirk to quiet WARN_ON()
iommu: Clear the freelist after iommu_put_pages_list()
iommu/vt-d: Change dmar_ats_supported() to return boolean
iommu/vt-d: Eliminate pci_physfn() in dmar_find_matched_satc_unit()
iommu/vt-d: Replace spin_lock with mutex to protect domain ida
iommu/vt-d: Use ida to manage domain id
iommu/vt-d: Restore WO permissions on second-level paging entries
iommu/amd: Allow matching ACPI HID devices without matching UIDs
iommu: make inclusion of arm/arm-smmu-v3 directory conditional
iommu: make inclusion of riscv directory conditional
iommu: make inclusion of amd directory conditional
iommu: make inclusion of intel directory conditional
iommu: remove duplicate selection of DMAR_TABLE
iommu/fsl_pamu: remove trailing space after \n
iommu/arm-smmu-qcom: Add SAR2130P MDSS compatible
...
Depending on the security set the response to L2CAP_LE_CONN_REQ shall be
just L2CAP_CR_LE_ENCRYPTION if only encryption when BT_SECURITY_MEDIUM
is selected since that means security mode 2 which doesn't require
authentication which is something that is covered in the qualification
test L2CAP/LE/CFC/BV-25-C.
Link: https://github.com/bluez/bluez/issues/1270
Fixes: 27e2d4c8d2 ("Bluetooth: Add basic LE L2CAP connect request receiving support")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit 3d05fc8223 ("Bluetooth: qca: set power_ctrl_enabled on NULL
returned by gpiod_get_optional()") accidentally changed the prevous
behavior where power control would be disabled without the BT_EN GPIO
only on QCA_WCN6750 and QCA_WCN6855 while also getting the error check
wrong. We should treat every IS_ERR() return value from
devm_gpiod_get_optional() as a reason to bail-out while we should only
set power_ctrl_enabled to false on the two models mentioned above. While
at it: use dev_err_probe() to save a LOC.
Cc: stable@vger.kernel.org
Fixes: 3d05fc8223 ("Bluetooth: qca: set power_ctrl_enabled on NULL returned by gpiod_get_optional()")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Hsin-chen Chuang <chharry@chromium.org>
Reviewed-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Return value of devm_request_irq() must be checked (function is even
annotated) and without it clang W=1 complains:
btnxpuart.c:494:6: error: unused variable 'ret' [-Werror,-Wunused-variable]
Setting up wakeup IRQ handler is not really critical, because the
handler is empty, so just log the informational message so user could
submit proper bug report and silences the clang warning.
Fixes: c50b56664e ("Bluetooth: btnxpuart: Implement host-wakeup feature")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In 'mgmt_hci_cmd_sync()', check whether the size of parameters passed
in 'struct mgmt_cp_hci_cmd_sync' matches the total size of the data
(i.e. 'sizeof(struct mgmt_cp_hci_cmd_sync)' plus trailing bytes).
Otherwise, large invalid 'params_len' will cause 'hci_cmd_sync_alloc()'
to do 'skb_put_data()' from an area beyond the one actually passed to
'mgmt_hci_cmd_sync()'.
Reported-by: syzbot+5fe2d5bfbfbec0b675a0@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=5fe2d5bfbfbec0b675a0
Fixes: 827af4787e ("Bluetooth: MGMT: Add initial implementation of MGMT_OP_HCI_CMD_SYNC")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When gfs2_sys_fs_add() fails, it sets sb->s_fs_info to NULL on its error
path (see commit 0d515210b6 ("GFS2: Add kobject release method")).
The intention seems to be to prevent dereferencing sb->s_fs_info once
the object pointed to has been deallocated, but that would be better
achieved by setting the pointer to NULL in free_sbd().
As a consequence, when the call to gfs2_sys_fs_add() fails in
gfs2_fill_super(), sdp = GFS2_SB(inode) will evaluate to NULL in iput()
-> gfs2_drop_inode(), and accessing sdp->sd_flags will be a NULL pointer
dereference.
Fix that by only setting sb->s_fs_info to NULL when actually freeing the
object pointed to in free_sbd().
Fixes: ae9f3bd825 ("gfs2: replace sd_aspace with sd_inode")
Reported-by: syzbot+b12826218502df019f9d@syzkaller.appspotmail.com
Signed-off-by: Andrew Price <anprice@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Pull rdma updates from Jason Gunthorpe:
"Usual collection of driver fixes:
- Small bug fixes and cleansup in hfi, hns, rxe, mlx5, mana siw
- Further ODP functionality in rxe
- Remote access MRs in mana, along with more page sizes
- Improve CM scalability with a rwlock around the agent
- More trace points for hns
- ODP hmm conversion to the new two step dma API
- Support the ethernet HW device in mana as well as the RNIC
- Cleanups:
- Use secs_to_jiffies() when appropriate
- Use ERR_CAST() instead of naked casts
- Don't use %pK in printk
- Unusued functions removed
- Allocation type matching"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (57 commits)
RDMA/cma: Fix hang when cma_netevent_callback fails to queue_work
RDMA/bnxt_re: Support extended stats for Thor2 VF
RDMA/hns: Fix endian issue in trace events
RDMA/mlx5: Avoid flexible array warning
IB/cm: Remove dead code and adjust naming
RDMA/core: Avoid hmm_dma_map_alloc() for virtual DMA devices
RDMA/rxe: Break endless pagefault loop for RO pages
RDMA/bnxt_re: Fix return code of bnxt_re_configure_cc
RDMA/bnxt_re: Fix missing error handling for tx_queue
RDMA/bnxt_re: Fix incorrect display of inactivity_cp in debugfs output
RDMA/mlx5: Add support for 200Gbps per lane speeds
RDMA/mlx5: Remove the redundant MLX5_IB_STAGE_UAR stage
RDMA/iwcm: Fix use-after-free of work objects after cm_id destruction
net: mana: Add support for auxiliary device servicing events
RDMA/mana_ib: unify mana_ib functions to support any gdma device
RDMA/mana_ib: Add support of mana_ib for RNIC and ETH nic
net: mana: Probe rdma device in mana driver
RDMA/siw: replace redundant ternary operator with just rv
RDMA/umem: Separate implicit ODP initialization from explicit ODP
RDMA/core: Convert UMEM ODP DMA mapping to caching IOVA and page linkage
...
Pull i2c updates from Wolfram Sang:
"Core updates:
- move towards using the 'fwnode' handle instead of 'of_node'
(meaning 'of_node' even gets removed from i2c_board_info)
- add support for Write Disable-aware SPD eeproms
- minor stuff (use new helpers, typo fixes)
i2c-atr (address translator) updates:
- support per-channel alias pools
- added support for dynamic address translation (also adds FPC202
driver as its user)
- add 'static' and 'passthrough' flags
Cleanups and refactorings
- Many drivers switched to dev_err_probe()
- Generic cleanups applied to designware, iproc, ismt, mlxbf,
npcm7xx, qcom-geni, pasemi, and thunderx
- davinci: declare I2C mangling support among I2C features
- designware: clean up DTS handling
- designware: fix PM runtime on driver unregister
- imx: improve error logging during probe
- lpc2k: improve checks in probe error path
- xgene-slimpro: improve PCC shared memory handling
- pasemi: improve error handling in reset, smbus clear, timeouts
- tegra: validate buffer length during transfers
- wmt: convert binding to YAML format
Improvements and extended support:
- microchip-core: add SMBus support
- mlxbf: add support for repeated start in block transfers
- mlxbf: improve timer configuration
- npcm: attempt clock toggle recovery before failing init
- octeon: add support for block mode operations
- pasemi: add support for unjam device feature
- riic: add support for bus recovery
New device support:
- MediaTek Dimensity 1200 (MT6893)
- Sophgo SG2044
- Renesas RZ/V2N (R9A09G056)
- Rockchip RK3528
- AMD ISP (new driver)"
* tag 'i2c-for-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (89 commits)
i2c: Use str_read_write() helper
i2c: mlxbf: avoid 64-bit division
i2c: viai2c-wmt: Replace dev_err() with dev_err_probe() in probe function
i2c: designware: Don't warn about missing get_clk_rate_khz
i2c: designware: Invoke runtime suspend on quick slave re-registration
i2c-mlxbf: Improve I2C bus timing configuration
i2c-mlxbf: Add repeated start condition support
i2c: xgene-slimpro: Replace dev_err() with dev_err_probe() in probe function
dt-bindings: i2c: i2c-wmt: Convert to YAML
i2c: microchip-corei2c: add smbus support
i2c: mlxbf: Allow build with COMPILE_TEST
i2c: I2C_DESIGNWARE_AMDISP should depend on DRM_AMD_ISP
i2c: atr: add passthrough flag
i2c: atr: add static flag
i2c: atr: allow replacing mappings in attach_addr()
i2c: atr: deduplicate logic in attach_addr()
i2c: atr: do not create mapping in detach_addr()
i2c: atr: split up i2c_atr_get_mapping_by_addr()
i2c: atr: find_mapping() -> get_mapping()
i2c: atr: Fix lockdep for nested ATRs
...
Pull pin control updates from Linus Walleij:
"An especially linear and sparse improvement and new drivers release.
Nothing exciting. The biggest change in Bartosz changes to make
gpiochip set/get calls return error codes (something we should have
fixed ages ago but is now finally getting fixed.)
Core changes:
- Add the devres devm_pinctrl_register_mappings() call that can
register some pin control machine mappings and have them go away
with the associated device
New drivers:
- Support for the Mediatek MT6893 and MT8196 SoCs
- Support for the Renesas RZ/V2N SoC
- Support for the NXP Freescale i.MX943 SoC
Improvements:
- Per-SoC suspend/resume callbacks in the Samsung drivers
- Set all pins as input (High-Z) at probe in the MCP23S08 driver
- Switch most GPIO chips to use the setters/getters with a return
value
- EGPIO support in the Qualcomm QCM2290 driver
- Fix up the number of available GPIO lines in Qualcomm QCS8300 and
QCS615"
* tag 'pinctrl-v6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: freescale: Add support for imx943 pinctrl
pinctrl: core: add devm_pinctrl_register_mappings()
pinctrl: remove extern specifier for functions in machine.h
pinctrl: mediatek: eint: Fix invalid pointer dereference for v1 platforms
pinctrl: freescale: Enable driver if platform is enabled.
pinctrl: freescale: Depend imx-scu driver on OF
pinctrl: armada-37xx: propagate error from armada_37xx_pmx_set_by_name()
pinctrl: armada-37xx: propagate error from armada_37xx_gpio_get_direction()
pinctrl: armada-37xx: propagate error from armada_37xx_pmx_gpio_set_direction()
pinctrl: armada-37xx: propagate error from armada_37xx_gpio_get()
pinctrl: armada-37xx: propagate error from armada_37xx_gpio_direction_output()
pinctrl: armada-37xx: set GPIO output value before setting direction
pinctrl: armada-37xx: use correct OUTPUT_VAL register for GPIOs > 31
pinctrl: meson: Drop unused aml_pctl_find_group_by_name()
pinctrl: at91: Fix possible out-of-boundary access
pinctrl: add stubs for OF-specific pinconf functions
pinctrl: qcom: correct the ngpios entry for QCS8300
pinctrl: qcom: correct the ngpios entry for QCS615
dt-bindings: pinctrl: qcom: correct gpio-ranges in examples for qcs8300
dt-bindings: pinctrl: qcom: correct gpio-ranges in examples for qcs615
...
Pull clk updates from Stephen Boyd:
"This has been a semi-quiet cycle. The core framework remains unchanged
this time around.
In terms of shiny new code though, we have support for the SpacemiT K1
SoC, Sophgo SG2044, and T-HEAD TH1520 VO clk drivers joining the usual
silicon players like Qualcomm, Samsung, Allwinner, and Renesas.
Surprisingly, the Qualcomm pile was smaller than usual but that is
likely because they put one SoC support inside a driver for a
different SoC that is very similar.
Other than all those new clk drivers there are the usual clk data
updates to fix parents, frequency tables, and add missing clks along
with some Kconfig changes to make compile testing simpler and even
more DT binding conversions to boot.
The exciting part is still the new SoC support like SpacemiT and
Sophgo support though, which really dominate the diffstat because they
introduce a whole new silicon vendor clk driver.
New Drivers:
- Camera clock controller driver for Qualcomm QCS8300
- DE (display engine) 3.3 clocks on Allwinner H616
- Samsung ExynosAutov920 CPU cluster CL0, CL1 and CL2 clock controllers
- Video Output (VO) subsystem clk controller in the T-HEAD TH1520 SoC
- Clock driver for Sophgo SG2044
- Clock driver for SpacemiT K1 SoC
- Renesas RZ/V2N (R9A09G056) SoC clk driver
Updates:
- Correct data in various SoC clk drivers
- Allow clkaN to be optional in the Qualcomm RPMh clock controller
driver if command db doesn't define it
- Change Kconfig options to not enable by default during compile
testing
- Add missing clks in various SoC clk drivers
- Remove some duplicate clk DT bindings and convert some more to
YAML"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (93 commits)
clk: qcom: gcc-x1e80100: Set FORCE MEM CORE for UFS clocks
clk: qcom: gcc: Set FORCE_MEM_CORE_ON for gcc_ufs_axi_clk for 8650/8750
clk: qcom: rpmh: make clkaN optional
clk: qcom: Add support for Camera Clock Controller on QCS8300
clk: rockchip: rk3528: add slab.h header include
clk: rockchip: rk3576: add missing slab.h include
clk: meson: Do not enable by default during compile testing
clk: meson-g12a: add missing fclk_div2 to spicc
clk: qcom: gcc-msm8939: Fix mclk0 & mclk1 for 24 MHz
clk: rockchip: rename gate-grf clk file
clk: rockchip: rename branch_muxgrf to branch_grf_mux
clk: sunxi-ng: ccu: add Display Engine 3.3 (DE33) support
dt-bindings: allwinner: add H616 DE33 clock binding
clk: samsung: correct clock summary for hsi1 block
dt-bindings: clock: add SM6350 QCOM video clock bindings
clk: rockchip: Pass NULL as reg pointer when registering GRF MMC clocks
clk: sunxi-ng: h616: Add LVDS reset for LCD TCON
dt-bindings: clock: sun50i-h616-ccu: Add LVDS reset
clk: rockchip: rk3036: mark ddrphy as critical
clk: rockchip: rk3036: fix implementation of usb480m clock mux
...
Pull f2fs updates from Jaegeuk Kim:
"In this round, Matthew converted most of page operations to using
folio. Beyond the work, we've applied some performance tunings such as
GC and linear lookup, in addition to enhancing fault injection and
sanity checks.
Enhancements:
- large number of folio conversions
- add a control to turn on/off the linear lookup for performance
- tune GC logics for zoned block device
- improve fault injection and sanity checks
Bug fixes:
- handle error cases of memory donation
- fix to correct check conditions in f2fs_cross_rename
- fix to skip f2fs_balance_fs() if checkpoint is disabled
- don't over-report free space or inodes in statvfs
- prevent the current section from being selected as a victim during GC
- fix to calculate first_zoned_segno correctly
- fix to avoid inconsistence between SIT and SSA for zoned block device
As usual, there are several debugging patches and clean-ups as well"
* tag 'f2fs-for-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (195 commits)
f2fs: fix to correct check conditions in f2fs_cross_rename
f2fs: use d_inode(dentry) cleanup dentry->d_inode
f2fs: fix to skip f2fs_balance_fs() if checkpoint is disabled
f2fs: clean up to check bi_status w/ BLK_STS_OK
f2fs: introduce is_{meta,node}_folio
f2fs: add ckpt_valid_blocks to the section entry
f2fs: add a method for calculating the remaining blocks in the current segment in LFS mode.
f2fs: introduce FAULT_VMALLOC
f2fs: use vmalloc instead of kvmalloc in .init_{,de}compress_ctx
f2fs: add f2fs_bug_on() in f2fs_quota_read()
f2fs: add f2fs_bug_on() to detect potential bug
f2fs: remove unused sbi argument from checksum functions
f2fs: fix 32-bits hexademical number in fault injection doc
f2fs: don't over-report free space or inodes in statvfs
f2fs: return bool from __write_node_folio
f2fs: simplify return value handling in f2fs_fsync_node_pages
f2fs: always unlock the page in f2fs_write_single_data_page
f2fs: remove wbc->for_reclaim handling
f2fs: return bool from __f2fs_write_meta_folio
f2fs: fix to return correct error number in f2fs_sync_node_pages()
...
Read card and package energy status using pmt apis instead
of xe_mmio for supported platforms.
Enable Battlemage to read energy from PMT.
v2:
- Remove unused has_pmt_energy field. (Badal)
- Use GENMASK to extract energy data. (Badal)
v3:
- Move PMT energy register offset and GENMASK to xe_pmt.h
- Address review comments. (Jani)
v4:
- Remove unnecessary debug print. (Badal)
v5:
- Resolve an unused variable warning.
- Add a return value check.
Signed-off-by: Karthik Poosa <karthik.poosa@intel.com>
Reviewed-by: Badal Nilawar <badal.nilawar@intel.com>
Link: https://lore.kernel.org/r/20250529163458.2354509-6-karthik.poosa@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Add support to manage power limit PL2 (burst limit) through
pcode mailbox commands.
v2:
- Update power1_cap definition in hwmon documentation. (Badal)
- Clamp PL2 power limit to GPU firmware default value.
v3:
- Activate the power label when either the PL1 or PL2 power
limit is enabled.
v4:
- Update description of pl2_on_boot variable to fix kernel-doc
error.
v5:
- Remove unnecessary drm_warn.
- Rectify powerX_label permission to read-only on platforms
without mailbox power limits support.
- Expose powerX_cap entries only on platforms with mailbox
support.
v6:
- Improve commit message, refer to BIOS as GPU firmware.
- Refer to card firmware as GPU firmware in code.
- Remove unnecessary drm_dbg.
- Print supported and unsupported power limits. (Rodrigo)
- Enable powerN_cap/max_xxx entries only when power limits
supported in GPU firmware.
Signed-off-by: Karthik Poosa <karthik.poosa@intel.com>
Reviewed-by: Badal Nilawar <badal.nilawar@intel.com>
Link: https://lore.kernel.org/r/20250529163458.2354509-4-karthik.poosa@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
