Since DP 1.3, it's been possible for DP receivers to specify an
additional set of DPCD capabilities, which can take precedence over the
capabilities reported at DP_DPCD_REV.
Basically any device supporting DP is going to need to read these in an
identical manner, in particular nouveau, so let's go ahead and just move
this code out of i915 into a shared DRM DP helper that we can use in
other drivers.
v2:
* Remove redundant dpcd[DP_DPCD_REV] == 0 check
* Fix drm_dp_dpcd_read() ret checks
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-20-lyude@redhat.com
Currently in nouveau_connector_ddc_detect() and
nouveau_connector_detect_lvds(), we start the connector probing process
by releasing the previous EDID and informing DRM of the change. However,
since commit 5186421cbf ("drm: Introduce epoch counter to
drm_connector") drm_connector_update_edid_property() actually checks
whether the new EDID we've specified is different from the previous one,
and updates the connector's epoch accordingly if it is. But, because we
always set the EDID to NULL first in nouveau_connector_ddc_detect() and
nouveau_connector_detect_lvds() we end up making DRM think that the EDID
changes every single time we do a connector probe - which isn't needed.
So, let's fix this by not clearing the EDID at the start of the
connector probing process, and instead simply changing or removing it
once near the end of the probing process. This will help prevent us from
sending unneeded hotplug events to userspace when nothing has actually
changed.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-19-lyude@redhat.com
This is another bit that we never implemented for nouveau: dongle
detection. When a "dongle", e.g. an active display adaptor, is hooked up
to the system and causes an HPD to be fired, we don't actually know
whether or not there's anything plugged into the dongle without checking
the sink count. As a result, plugging in a dongle without anything
plugged into it currently results in a bogus EDID retrieval error in the kernel log.
Additionally, most dongles won't send another long HPD signal if the
user suddenly plugs something in, they'll only send a short HPD IRQ with
the expectation that the source will check the sink count and reprobe
the connector if it's changed - something we don't actually do. As a
result, nothing will happen if the user plugs the dongle in before
plugging something into the dongle.
So, let's fix this by checking the sink count in both
nouveau_dp_probe_dpcd() and nouveau_dp_irq(), and reprobing the
connector if things change.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-18-lyude@redhat.com
And of course, we'll also need to read the sink count from other drivers
as well if we're checking whether or not it's supported. So, let's
extract the code for this into another helper.
v2:
* Fix drm_dp_dpcd_readb() ret check
* Add back comment and move back sink_count assignment in intel_dp_get_dpcd()
v5:
* Change name from drm_dp_get_sink_count() to drm_dp_read_sink_count()
* Also, add "See also:" section to kdocs
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-17-lyude@redhat.com
Since other drivers are also going to need to be aware of the sink count
in order to do proper dongle detection, we might as well steal i915's
DP_SINK_COUNT helpers and move them into DRM helpers so that other
dirvers can use them as well.
Note that this also starts using intel_dp_has_sink_count() in
intel_dp_detect_dpcd(), which is a functional change.
v5:
* Change name from drm_dp_has_sink_count() to
drm_dp_read_sink_count_cap()
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-16-lyude@redhat.com
This adds support for querying the maximum clock rate of a downstream
port on a DisplayPort connection. Generally, downstream ports refer to
active dongles which can have their own pixel clock limits.
Note as well, we also start marking the connector as disconnected if we
can't read the DPCD, since we wouldn't be able to do anything without
DPCD access anyway.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-15-lyude@redhat.com
We're going to be doing the same probing process in nouveau for
determining downstream DP port capabilities, so let's deduplicate the
work by moving i915's code for handling this into a shared helper:
drm_dp_read_downstream_info().
Note that when we do this, we also do make some functional changes while
we're at it:
* We always clear the downstream port info before trying to read it,
just to make things easier for the caller
* We skip reading downstream port info if the DPCD indicates that we
don't support downstream port info
* We only read as many bytes as needed for the reported number of
downstream ports, no sense in reading the whole thing every time
v2:
* Fixup logic for calculating the downstream port length to account for
the fact that downstream port caps can be either 1 byte or 4 bytes
long. We can actually skip fixing the max_clock/max_bpc helpers here
since they all check for DP_DETAILED_CAP_INFO_AVAILABLE anyway.
* Fix ret code check for drm_dp_dpcd_read
v5:
* Change name from drm_dp_downstream_read_info() to
drm_dp_read_downstream_info()
* Also, add "See Also" sections for the various downstream info
functions (drm_dp_read_downstream_info(), drm_dp_downstream_max_clock(),
drm_dp_downstream_max_bpc())
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-14-lyude@redhat.com
Currently we perform both short IRQ handling for DP, and connector
reprobing in the HPD IRQ handler. However since we need to grab
connection_mutex in order to reprobe a connector, in theory we could
accidentally block ourselves from handling any short IRQs until after a
modeset completes if a connector hotplug happens to occur in parallel
with a modeset.
I haven't seen this actually happen yet, but since we're cleaning up
nouveau's hotplug handling code anyway and we already have a hpd worker,
we can simply fix this by only relying on the HPD worker to actually
reprobe connectors when we receive a HPD IRQ. We also add a mask to
nouveau_drm to keep track of which connectors are waiting to be reprobed
in response to an HPD IRQ.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-13-lyude@redhat.com
For whatever reason we currently unset the EDID for DP CEC support when
responding to the connector being unplugged, instead of just doing it in
nouveau_connector_detect() where we set the CEC EDID. This isn't really
needed and could even potentially cause us to forget to unset the EDID
if the connector is removed without a corresponding hpd event, so let's
fix that.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-12-lyude@redhat.com
First some backstory here: Currently, we keep track of whether or not
we've enabled MST or not by trying to piggy-back off the MST helpers.
This means that in order to check whether MST is enabled or not, we
actually need to grab drm_dp_mst_topology_mgr.lock.
Back when I originally wrote this, I did this piggy-backing with the
intention that I'd eventually be teaching our MST helpers how to recover
when an MST device has stopped responding, which in turn would require
the MST helpers having a way of disabling MST independently of the
driver. Note that this was before I reworked locking in the MST helpers,
so at the time we were sticking random things under &mgr->lock - which
grabbing this lock was meant to protect against.
This never came to fruition because doing such a reset safely turned out
to be a lot more painful and impossible then it sounds, and also just
risks us working around issues with our MST handlers that should be
properly fixed instead. Even if it did though, simply calling
drm_dp_mst_topology_mgr_set_mst() from the MST helpers (with the
exception of when we're tearing down our MST managers, that's always OK)
wouldn't have been a bad idea, since drivers like nouveau and i915 need
to do their own book keeping immediately after disabling MST.
So-implementing that would likely require adding a hook for
helper-triggered MST disables anyway.
So, fast forward to now - we want to start adding support for all of the
miscellaneous bits of the DP protocol (for both SST and MST) we're
missing before moving on to supporting more complicated features like
supporting different BPP values on MST, DSC, etc. Since many of these
features only exist on SST and make use of DP HPD IRQs, we want to be
able to atomically check whether we're servicing an MST IRQ or SST IRQ
in nouveau_connector_hotplug(). Currently we literally don't do this at
all, and just handle any kind of possible DP IRQ we could get including
ESIs - even if MST isn't actually enabled.
This would be very complicated and difficult to fix if we need to hold
&mgr->lock while handling SST IRQs to ensure that the MST topology
state doesn't change under us. What we really want here is to do our own
tracking of whether MST is enabled or not, similar to drivers like i915,
and define our own locking order to decomplicate things and avoid
hitting locking issues in the future.
So, let's do this by refactoring our MST probing/enabling code to use
our own MST bookkeeping, along with adding a lock for protecting DP
state that needs to be checked outside of our connector probing
functions. While we're at it, we also remove a bunch of unneeded steps
we perform when probing/enabling MST:
* Enabling bits in MSTM_CTRL before calling drm_dp_mst_topology_mgr_set_mst().
I don't think these ever actually did anything, since the nvif methods
for enabling MST don't actually do anything DPCD related and merely
indicate to nvkm that we've turned on MST.
* Checking the MSTM_CTRL bit is intact when checking the state of an
enabled MST topology in nv50_mstm_detect(). I just added this to be safe
originally, but now that we try reading the DPCD when probing DP
connectors it shouldn't be needed as that will abort our hotplug probing
if the device was removed well before we start checking for MST..
* All of the duplicate DPCD version checks.
This leaves us with much nicer looking code, a much more sensible
locking scheme, and an easy way of checking whether MST is enabled or
not for handling DP HPD IRQs.
v2:
* Get rid of accidental newlines
v4:
* Fix uninitialized usage of mstm in nv50_mstm_detect() - thanks kernel
bot!
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-9-lyude@redhat.com
While the way we find the associated connector for an encoder is just
fine for legacy modesetting, it's not correct for nv50+ since that uses
atomic modesetting. For reference, see the drm_encoder kdocs.
Fix this by removing nouveau_encoder_connector_get(), and replacing it
with nv04_encoder_get_connector(), nv50_outp_get_old_connector(), and
nv50_outp_get_new_connector().
v2:
* Don't line-wrap for_each_(old|new)_connector_in_state in
nv50_outp_get_(old|new)_connector() - sravn
v3:
* Fix potential uninitialized usage of nv_connector (needs to be
initialized to NULL at the start). Thanks kernel test robot!
v4:
* Actually fix uninitialized nv_connector usage in
nv50_audio_component_get_eld(). The previous fix wouldn't have worked
since we would have started out with nv_connector == NULL, but
wouldn't clear it after a single drm_for_each_encoder() iteration.
Thanks again Kernel bot!
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-7-lyude@redhat.com
Add support for reporting GPU reset events through SMI. KFD
would report both pre and post GPU reset events.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Even if support for the IPU was compiled in, we may run on a device
(e.g. the Qi LB60) where the IPU is not available, or simply with an old
devicetree without the IPU node. In that case the ingenic-drm refused to
probe.
Fix the driver so that it will probe even if the IPU node is not present
in devicetree (but then IPU support is disabled of course).
v2: Take a different approach
Fixes: fc1acf317b ("drm/ingenic: Add support for the IPU")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200827114404.36748-2-paul@crapouillou.net
The VKMS blend function was ignoring the alpha channel and just
overwriting vaddr_src with vaddr_dst. This XRGB approach triggers a
warning when running the kms_cursor_crc/cursor-alpha-transparent test
case. In IGT, cairo_format_argb32 uses premultiplied alpha (according to
documentation). Also current DRM assumption is that alpha is
premultiplied. Therefore, this patch considers premultiplied alpha
blending eq to compose vaddr_src with vaddr_dst.
This change removes the following cursor-alpha-transparent warning:
"Suspicious CRC: All values are 0."
V2:
- static for local functions
- const for the read-only variable argb_src
- replaces variable names
- drops unnecessary comment
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Cc: Haneen Mohammed <hamohammed.sa@gmail.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200825114532.abzdooluny2ekzvm@smtp.gmail.com
Clang warns:
drivers/gpu/drm/i915/display/intel_combo_phy.c:268:3: warning: variable
'ret' is uninitialized when used here [-Wuninitialized]
ret &= check_phy_reg(dev_priv, phy, ICL_PORT_TX_DW8_LN0(phy),
^~~
drivers/gpu/drm/i915/display/intel_combo_phy.c:261:10: note: initialize
the variable 'ret' to silence this warning
bool ret;
^
= 0
1 warning generated.
In practice, the bug this warning appears to be concerned with would not
actually matter because ret gets initialized to the return value of
cnl_verify_procmon_ref_values. However, that does appear to be a bug
since it means the first hunk of the patch this fixes won't actually do
anything (since the values of check_phy_reg won't factor into the final
ret value). Initialize ret to true then make all of the assignments a
bitwise AND with itself so that the function always does what it should
do.
Fixes: 239bef676d ("drm/i915/display: Implement new combo phy initialization step")
Link: https://github.com/ClangBuiltLinux/linux/issues/1094
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200828202830.7165-1-jose.souza@intel.com
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Fixes below compiler warnings:
CC [M] drivers/gpu/drm/amd/amdgpu/amdgpu_device.o
drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:381:1: warning: ‘static’ is not at beginning of declaration [-Wold-style-declaration]
381 | void static inline amdgpu_mm_wreg_mmio(struct amdgpu_device *adev, uint32_t reg, uint32_t v, uint32_t acc_flags)
| ^~~~
drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:381:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
drivers/gpu/drm/amd/amdgpu/amdgpu_device.c: In function ‘amdgpu_device_fini’:
drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:3381:6: warning: variable ‘r’ set but not used [-Wunused-but-set-variable]
3381 | int r;
| ^
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
