The main change is to adjust RX calibration groups from {0,1,2,3} to {0,2}
in 5 GHz, so reduce elements from 4 to 2, and use index to iterate them.
Meanwhile, always do RX narrowband calibration (ID_NBRXK) for each group.
NCTL is used to assist IQK, so also update NCTL to 0x6 along with internal
tag HALRF_029_00_103.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-5-pkshih@realtek.com
Without this patch, firmware only track beacons for port 0 and since
we will always start AP on port 0, this results in misbehavior of
power saving mode on other ports after AP stops.
The "default port" H2C command is used to notify which port should
firmware track. Update the correct settings to firmware so power
saving mode can work properly.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616125540.36877-7-pkshih@realtek.com
Broadcast and multicast packets in high queue should be transmitted
all at once during DTIM. But without proper settings, hardware fails
to recognize that there are multiple packets and fetches only one.
Fix this by signaling hardware with more data bit set when there are
packets in the high queue.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616125540.36877-3-pkshih@realtek.com
In the wpa_supplicant rekey flow, it sends an EAPOL packet 4/4 through
nl80211_tx_control_port() and triggers wake_tx_queue() in the driver.
Then, it sends nl80211_new_key() to configure a new key in mac80211.
However, in wake_tx_queue(), a workqueue is used to process the tx packet,
which might cause the driver to process the EAPOL packet later than
nl80211_new_key(). As a result, the EAPOL 4/4 packet is dropped by mac80211
due to the rekey configuration being finished. The EAPOL packets belongs to
VO packets that need high priority. Therefore, we process VO packets
directly without workqueue to ensure that packets can process immediately.
VO is normally used by voice application that is low traffic load and low
latency, that doesn't affect user experience.
We test iperf with VO packets(iperf3 -P4 -u -b 10000M -S 0xdf)
before after
TX throughput 162M 162M
ping RTT 3.8ms 3.7ms
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616031713.16769-1-pkshih@realtek.com
For combo chips, antennas were controlled by bluetooth only during
power on. If WiFi wish to do transmission, notification to the coexistence
module are required. Previously we only do this before authentication.
To allow transmission before auth, such as management TX, now we start
the initiation of coexistence earlier so antennas are shared between
WiFi and bluetooth after set_channel(), and frames could then be sent.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615114348.7193-1-pkshih@realtek.com
We currently allow to create perf link for program with
expected_attach_type == BPF_TRACE_KPROBE_MULTI.
This will cause crash when we call helpers like get_attach_cookie or
get_func_ip in such program, because it will call the kprobe_multi's
version (current->bpf_ctx context setup) of those helpers while it
expects perf_link's current->bpf_ctx context setup.
Making sure that we use BPF_TRACE_KPROBE_MULTI expected_attach_type
only for programs attaching through kprobe_multi link.
Fixes: ca74823c6e ("bpf: Add cookie support to programs attached with kprobe multi link")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230618131414.75649-1-jolsa@kernel.org
When building a kernel with LLVM=1, LLVM_IAS=0 and CONFIG_KASAN=y, LLVM
leaves DWARF tags for the "asan.module_ctor" & co symbols. In turn,
pahole creates BTF_KIND_FUNC entries for these and this makes the BTF
metadata validation fail because they contain a dot.
In a dramatic turn of event, this BTF verification failure can cause
the netfilter_bpf initialization to fail, causing netfilter_core to
free the netfilter_helper hashmap and netfilter_ftp to trigger a
use-after-free. The risk of u-a-f in netfilter will be addressed
separately but the existence of "asan.module_ctor" debug info under some
build conditions sounds like a good enough reason to accept functions
that contain dots in BTF.
Although using only LLVM=1 is the recommended way to compile clang-based
kernels, users can certainly do LLVM=1, LLVM_IAS=0 as well and we still
try to support that combination according to Nick. To clarify:
- > v5.10 kernel, LLVM=1 (LLVM_IAS=0 is not the default) is recommended,
but user can still have LLVM=1, LLVM_IAS=0 to trigger the issue
- <= 5.10 kernel, LLVM=1 (LLVM_IAS=0 is the default) is recommended in
which case GNU as will be used
Fixes: 1dc9285184 ("bpf: kernel side support for BTF Var and DataSec")
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Cc: Yonghong Song <yhs@meta.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/bpf/20230615145607.3469985-1-revest@chromium.org
This reverts commit 07b679f70d.
This change appears to have broken things...
We now see applications hanging during disk accesses.
e.g.
multi-port virtio-blk device running in h/w (FPGA)
Host running a simple 'fio' test.
[global]
thread=1
direct=1
ioengine=libaio
norandommap=1
group_reporting=1
bs=4K
rw=read
iodepth=128
runtime=1
numjobs=4
time_based
[job0]
filename=/dev/vda
[job1]
filename=/dev/vdb
[job2]
filename=/dev/vdc
...
[job15]
filename=/dev/vdp
i.e. 16 disks; 4 queues per disk; simple burst of 4KB reads
This is repeatedly run in a loop.
After a few, normally <10 seconds, fio hangs.
With 64 queues (16 disks), failure occurs within a few seconds; with 8 queues (2 disks) it may take ~hour before hanging.
Last message:
fio-3.19
Starting 8 threads
Jobs: 1 (f=1): [_(7),R(1)][68.3%][eta 03h:11m:06s]
I think this means at the end of the run 1 queue was left incomplete.
'diskstats' (run while fio is hung) shows no outstanding transactions.
e.g.
$ cat /proc/diskstats
...
252 0 vda 1843140071 0 14745120568 712568645 0 0 0 0 0 3117947 712568645 0 0 0 0 0 0
252 16 vdb 1816291511 0 14530332088 704905623 0 0 0 0 0 3117711 704905623 0 0 0 0 0 0
...
Other stats (in the h/w, and added to the virtio-blk driver ([a]virtio_queue_rq(), [b]virtblk_handle_req(), [c]virtblk_request_done()) all agree, and show every request had a completion, and that virtblk_request_done() never gets called.
e.g.
PF= 0 vq=0 1 2 3
[a]request_count - 839416590 813148916 105586179 84988123
[b]completion1_count - 839416590 813148916 105586179 84988123
[c]completion2_count - 0 0 0 0
PF= 1 vq=0 1 2 3
[a]request_count - 823335887 812516140 104582672 75856549
[b]completion1_count - 823335887 812516140 104582672 75856549
[c]completion2_count - 0 0 0 0
i.e. the issue is after the virtio-blk driver.
This change was introduced in kernel 6.3.0.
I am seeing this using 6.3.3.
If I run with an earlier kernel (5.15), it does not occur.
If I make a simple patch to the 6.3.3 virtio-blk driver, to skip the blk_mq_add_to_batch()call, it does not fail.
e.g.
kernel 5.15 - this is OK
virtio_blk.c,virtblk_done() [irq handler]
if (likely(!blk_should_fake_timeout(req->q))) {
blk_mq_complete_request(req);
}
kernel 6.3.3 - this fails
virtio_blk.c,virtblk_handle_req() [irq handler]
if (likely(!blk_should_fake_timeout(req->q))) {
if (!blk_mq_complete_request_remote(req)) {
if (!blk_mq_add_to_batch(req, iob, virtblk_vbr_status(vbr), virtblk_complete_batch)) {
virtblk_request_done(req); //this never gets called... so blk_mq_add_to_batch() must always succeed
}
}
}
If I do, kernel 6.3.3 - this is OK
virtio_blk.c,virtblk_handle_req() [irq handler]
if (likely(!blk_should_fake_timeout(req->q))) {
if (!blk_mq_complete_request_remote(req)) {
virtblk_request_done(req); //force this here...
if (!blk_mq_add_to_batch(req, iob, virtblk_vbr_status(vbr), virtblk_complete_batch)) {
virtblk_request_done(req); //this never gets called... so blk_mq_add_to_batch() must always succeed
}
}
}
Perhaps you might like to fix/test/revert this change...
Martin
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306090826.C1fZmdMe-lkp@intel.com/
Cc: Suwan Kim <suwan.kim027@gmail.com>
Tested-by: edliaw@google.com
Reported-by: "Roberts, Martin" <martin.roberts@intel.com>
Message-Id: <336455b4f630f329380a8f53ee8cad3868764d5c.1686295549.git.mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
sa8775p uses EMAC version 4, add the relevant defines, rename the
has_emac3 switch to has_emac_ge_3 (has emac greater-or-equal than 3)
and add the new compatible.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the compatible for the MAC controller on sa8775p platforms. This MAC
works with a single interrupt so add minItems to the interrupts property.
The fourth clock's name is different here so change it. Enable relevant
PHY properties. Add the relevant compatibles to the binding document for
snps,dwmac as well.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On some platforms, the PCS can be integrated in the MAC so the driver
will not see any PCS link activity. Add a switch that allows the platform
drivers to let the core code know.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On sa8775p the MAC is connected to the external PHY over SGMII so add
support for it to the driver.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for supporting SGMII, let's make the code a bit more
generic. Add a new callback for MAC configuration so that we can assign
a different variant of it in the future.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On sa8775p, the EMAC revision is 4 and we use SGMII instead of RGMII.
There's no "rgmii" clock but there's a fourth clock under a different
name: "phyaux". Add a new field to the chip data struct that specifies
the link clock name. Default to "rgmii" for backward compatibility.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On sa8775p platforms, there's a SGMII SerDes PHY between the MAC and
external PHY that we need to enable and configure.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
