Ensure the current pin frequency is always present in the list of
supported frequencies reported to userspace. Previously, if the
firmware node was missing or didn't include the current operating
frequency in the supported-frequencies-hz property, the pin would
report a frequency that wasn't in its supported list.
Get the current frequency early in zl3073x_pin_props_get():
- For input pins: use zl3073x_dev_ref_freq_get()
- For output pins: use zl3073x_dev_output_pin_freq_get()
Place the current frequency at index 0 of the supported frequencies
array, then append frequencies from the firmware node (if present),
skipping any duplicate of the current frequency.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260205154350.3180465-3-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce zl3073x_dev_output_pin_freq_get() helper function to compute
the output pin frequency based on synthesizer frequency, output divisor,
and signal format. For N-div signal formats, the N-pin frequency is
additionally divided by esync_n_period.
Add zl3073x_out_is_ndiv() helper to check if an output is configured
in N-div mode (2_NDIV or 2_NDIV_INV signal formats).
Refactor zl3073x_dpll_output_pin_frequency_get() callback to use the
new helper, reducing code duplication and enabling reuse of the
frequency calculation logic in other contexts.
This is a preparatory change for adding current frequency to the
supported frequencies list in pin properties.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260205154350.3180465-2-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The output pin phase adjustment functions incorrectly negate the phase
compensation value.
Per the ZL3073x datasheet, the output phase compensation register is
simply a signed two's complement integer where:
- Positive values move the phase later in time
- Negative values move the phase earlier in time
No negation is required. The erroneous negation caused phase adjustments
to be applied in the wrong direction.
Note that input pin phase adjustment correctly uses negation because the
hardware has an inverted convention for input references (positive moves
phase earlier, negative moves phase later).
Fixes: 6287262f76 ("dpll: zl3073x: Add support to adjust phase")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20260205181055.129768-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update existing DPLL drivers to utilize the DPLL reference count
tracking infrastructure.
Add dpll_tracker fields to the drivers' internal device and pin
structures. Pass pointers to these trackers when calling
dpll_device_get/put() and dpll_pin_get/put().
This allows developers to inspect the specific references held by this
driver via debugfs when CONFIG_DPLL_REFCNT_TRACKER is enabled, aiding
in the debugging of resource leaks.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Link: https://patch.msgid.link/20260203174002.705176-9-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for the REF_TRACKER infrastructure to the DPLL subsystem.
When enabled, this allows developers to track and debug reference counting
leaks or imbalances for dpll_device and dpll_pin objects. It records stack
traces for every get/put operation and exposes this information via
debugfs at:
/sys/kernel/debug/ref_tracker/dpll_device_*
/sys/kernel/debug/ref_tracker/dpll_pin_*
The following API changes are made to support this:
1. dpll_device_get() / dpll_device_put() now accept a 'dpll_tracker *'
(which is a typedef to 'struct ref_tracker *' when enabled, or an empty
struct otherwise).
2. dpll_pin_get() / dpll_pin_put() and fwnode_dpll_pin_find() similarly
accept the tracker argument.
3. Internal registration structures now hold a tracker to associate the
reference held by the registration with the specific owner.
All existing in-tree drivers (ice, mlx5, ptp_ocp, zl3073x) are updated
to pass NULL for the new tracker argument, maintaining current behavior
while enabling future debugging capabilities.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Co-developed-by: Petr Oros <poros@redhat.com>
Signed-off-by: Petr Oros <poros@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Link: https://patch.msgid.link/20260203174002.705176-8-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Refactor the reference counting mechanism for DPLL devices and pins to
improve consistency and prevent potential lifetime issues.
Introduce internal helpers __dpll_{device,pin}_{hold,put}() to
centralize reference management.
Update the internal XArray reference helpers (dpll_xa_ref_*) to
automatically grab a reference to the target object when it is added to
a list, and release it when removed. This ensures that objects linked
internally (e.g., pins referenced by parent pins) are properly kept
alive without relying on the caller to manually manage the count.
Consequently, remove the now redundant manual `refcount_inc/dec` calls
in dpll_pin_on_pin_{,un}register()`, as ownership is now correctly handled
by the dpll_xa_ref_* functions.
Additionally, ensure that dpll_device_{,un}register()` takes/releases
a reference to the device, ensuring the device object remains valid for
the duration of its registration.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Link: https://patch.msgid.link/20260203174002.705176-7-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Allow drivers to register DPLL pins without manually specifying a pin
index.
Currently, drivers must provide a unique pin index when calling
dpll_pin_get(). This works well for hardware-mapped pins but creates
friction for drivers handling virtual pins or those without a strict
hardware indexing scheme.
Introduce DPLL_PIN_IDX_UNSPEC (U32_MAX). When a driver passes this
value as the pin index:
1. The core allocates a unique index using an IDA
2. The allocated index is mapped to a range starting above `INT_MAX`
This separation ensures that dynamically allocated indices never collide
with standard driver-provided hardware indices, which are assumed to be
within the `0` to `INT_MAX` range. The index is automatically freed when
the pin is released in dpll_pin_put().
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Link: https://patch.msgid.link/20260203174002.705176-5-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, the DPLL subsystem reports events (creation, deletion, changes)
to userspace via Netlink. However, there is no mechanism for other kernel
components to be notified of these events directly.
Add a raw notifier chain to the DPLL core protected by dpll_lock. This
allows other kernel subsystems or drivers to register callbacks and
receive notifications when DPLL devices or pins are created, deleted,
or modified.
Define the following:
- Registration helpers: {,un}register_dpll_notifier()
- Event types: DPLL_DEVICE_CREATED, DPLL_PIN_CREATED, etc.
- Context structures: dpll_{device,pin}_notifier_info to pass relevant
data to the listeners.
The notification chain is invoked alongside the existing Netlink event
generation to ensure in-kernel listeners are kept in sync with the
subsystem state.
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Co-developed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Link: https://patch.msgid.link/20260203174002.705176-4-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Extend the DPLL core to support associating a DPLL pin with a firmware
node. This association is required to allow other subsystems (such as
network drivers) to locate and request specific DPLL pins defined in
the Device Tree or ACPI.
* Add a .fwnode field to the struct dpll_pin
* Introduce dpll_pin_fwnode_set() helper to allow the provider driver
to associate a pin with a fwnode after the pin has been allocated
* Introduce fwnode_dpll_pin_find() helper to allow consumers to search
for a registered DPLL pin using its associated fwnode handle
* Ensure the fwnode reference is properly released in dpll_pin_put()
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Link: https://patch.msgid.link/20260203174002.705176-2-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, the dpll subsystem exports the fractional frequency offset
(FFO) in parts per million (ppm). This granularity is insufficient for
high-precision synchronization scenarios which often require parts per
trillion (ppt) resolution.
Add a new netlink attribute DPLL_A_PIN_FRACTIONAL_FREQUENCY_OFFSET_PPT
to expose the FFO in ppt.
Update the dpll netlink core to expect the driver-provided FFO value
to be in ppt. To maintain backward compatibility with existing userspace
tools, populate the legacy DPLL_A_PIN_FRACTIONAL_FREQUENCY_OFFSET
attribute by dividing the new ppt value by 1,000,000.
Update the zl3073x and mlx5 drivers to provide the FFO value in ppt:
- zl3073x: adjust the fixed-point calculation to produce ppt (10^12)
instead of ppm (10^6).
- mlx5: scale the existing ppm value by 1,000,000.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20260126162253.27890-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Modify the internal registration helpers dpll_xa_ref_{dpll,pin}_add()
to reject duplicate registration attempts.
Previously, if a caller attempted to register the same pin multiple
times (with the same ops, priv, and cookie) on the same device, the core
silently increments the reference count and return success. This behavior
is incorrect because if the caller makes these duplicate registrations
then for the first one dpll_pin_registration is allocated and for others
the associated dpll_pin_ref.refcount is incremented. During the first
unregistration the associated dpll_pin_registration is freed and for
others WARN is fired.
Fix this by updating the logic to return `-EEXIST` if a matching
registration is found to enforce a strict "register once" policy.
Fixes: 9431063ad3 ("dpll: core: Add DPLL framework base functions")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20260121130012.112606-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for .supported_modes_get() and .mode_set() callbacks
to enable switching between manual and automatic modes via netlink.
Implement .supported_modes_get() to report available modes based
on the current hardware configuration:
* manual mode is always supported
* automatic mode is supported unless the dpll channel is configured
in NCO (Numerically Controlled Oscillator) mode
Implement .mode_set() to handle the specific logic required when
transitioning between modes:
1) Transition to manual:
* If a valid reference is currently active, switch the hardware
to ref-lock mode (force lock to that reference).
* If no reference is valid and the DPLL is unlocked, switch to freerun.
* Otherwise, switch to Holdover.
2) Transition to automatic:
* If the currently selected reference pin was previously marked
as non-selectable (likely during a previous manual forcing
operation), restore its priority and selectability in the hardware.
* Switch the hardware to Automatic selection mode.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Link: https://patch.msgid.link/20260114122726.120303-4-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, userspace can retrieve the DPLL working mode but cannot
configure it. This prevents changing the device operation, such as
switching from manual to automatic mode and vice versa.
Add a new callback .mode_set() to struct dpll_device_ops. Extend
the netlink policy and device-set command handling to process
the DPLL_A_MODE attribute. Update the netlink YAML specification
to include the mode attribute in the device-set operation.
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260114122726.120303-3-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the DPLL subsystem assumes that the only supported mode is
the one currently active on the device. When dpll_msg_add_mode_supported()
is called, it relies on ops->mode_get() and reports that single mode
to userspace. This prevents users from discovering other modes the device
might be capable of.
Add a new callback .supported_modes_get() to struct dpll_device_ops. This
allows drivers to populate a bitmap indicating all modes supported by
the hardware.
Update dpll_msg_add_mode_supported() to utilize this new callback:
* if ops->supported_modes_get is defined, use it to retrieve the full
bitmap of supported modes.
* if not defined, fall back to the existing behavior: retrieve
the current mode via ops->mode_get and set the corresponding bit
in the bitmap.
Finally, iterate over the bitmap and add a DPLL_A_MODE_SUPPORTED netlink
attribute for every set bit, accurately reporting the device's capabilities
to userspace.
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260114122726.120303-2-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove several zl3073x_dev_... inline wrapper functions from core.h
as they are no longer used by any callers.
Removed functions:
* zl3073x_dev_ref_ffo_get
* zl3073x_dev_ref_is_enabled
* zl3073x_dev_synth_dpll_get
* zl3073x_dev_synth_is_enabled
* zl3073x_dev_out_signal_format_get
This is a cleanup after recent refactoring, as the remaining callers
now fetch the state object and use the base helpers directly.
Reviewed-by: Petr Oros <poros@redhat.com>
Tested-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251113074105.141379-7-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Expand the zl3073x_out structure to cache all output-related
hardware registers, including divisors, widths, embedded-sync
parameters and phase compensation.
Modify zl3073x_out_state_fetch() to read and populate all these
new fields at once, including zero-divisor checks. Refactor all
dpll "getter" functions in dpll.c to read from this new
cached state instead of performing direct register access.
Introduce a new function, zl3073x_out_state_set(), to handle
writing changes back to the hardware. This function compares the
provided state with the current cached state and writes *only* the
modified register values via a single mailbox sequence before
updating the local cache.
Refactor all dpll "setter" functions to modify a local copy of
the output state and then call zl3073x_out_state_set() to
commit the changes.
This change centralizes all output-related register I/O into
out.c, significantly reduces bus traffic, and simplifies the logic
in dpll.c.
Reviewed-by: Petr Oros <poros@redhat.com>
Tested-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251113074105.141379-6-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Expand the zl3073x_ref structure to cache all reference-related
hardware registers, including frequency components, embedded-sync
settings and phase compensation. Previously, these registers were
read on-demand from various functions in dpll.c leading to frequent
mailbox operations.
Modify zl3073x_ref_state_fetch() to read and populate all these new
fields at once. Refactor all "getter" functions in dpll.c to read
from this new cached state instead of performing direct register
access.
Remove the standalone zl3073x_dpll_input_ref_frequency_get() helper,
as its functionality is now replaced by zl3073x_ref_freq_get() which
operates on the cached state and add a corresponding zl3073x_dev_...
wrapper.
Introduce a new function, zl3073x_ref_state_set(), to handle
writing changes back to the hardware. This function compares the
provided state with the current cached state and writes *only* the
modified register values to the device via a single mailbox sequence
before updating the local cache.
Refactor all dpll "setter" functions to modify a local copy of the
ref state and then call zl3073x_ref_state_set() to commit the changes.
As a cleanup, update callers in dpll.c that already have
a struct zl3073x_ref * to use the direct helpers instead of the
zl3073x_dev_... wrappers.
This change centralizes all reference-related register I/O into ref.c,
significantly reduces bus traffic, and simplifies the logic in dpll.c.
Reviewed-by: Petr Oros <poros@redhat.com>
Tested-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251113074105.141379-5-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of reading the ZL_REG_REF_MON_STATUS register every time
the reference status is needed, cache this value in the zl3073x_ref
struct.
This is achieved by:
* Adding a mon_status field to struct zl3073x_ref
* Introducing zl3073x_dev_ref_status_update() to read the status for
all references into this new cache field
* Calling this update function from the periodic work handler
* Adding zl3073x_ref_is_status_ok() and zl3073x_dev_ref_is_status_ok()
helpers to check the cached value
* Refactoring all callers in dpll.c to use the new
zl3073x_dev_ref_is_status_ok() helper, removing direct register reads
This change consolidates all status register reads into a single periodic
function and reduces I/O bus traffic in dpll callbacks.
Reviewed-by: Petr Oros <poros@redhat.com>
Tested-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251113074105.141379-4-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor the zl3073x driver by splitting the logic for input
references, outputs and synthesizers out of the monolithic
core.[ch] files.
Move the logic for each functional block into its own dedicated files:
ref.[ch], out.[ch] and synth.[ch].
Specifically:
- Move state structures (zl3073x_ref, zl3073x_out, zl3073x_synth)
from core.h into their respective new headers
- Move state-fetching functions (..._state_fetch) from core.c to their
new .c files
- Move the zl3073x_ref_freq_factorize helper from core.c to ref.c
- Introduce a new helper layer to decouple the core device logic from
the state-parsing logic:
1. Move the original inline helpers (e.g., zl3073x_ref_is_enabled)
to the new headers (ref.h, etc.) and make them operate on a
const struct ... * pointer.
2. Create new zl3073x_dev_... prefixed functions in core.h
(e.g., zl3073x_dev_ref_is_enabled) and Implement these _dev_ functions
to fetch state using a new ..._state_get() helper and then call
the non-prefixed helper.
3. Update all driver-internal callers (in dpll.c, prop.c, etc.) to use
the new zl3073x_dev_... functions.
Reviewed-by: Petr Oros <poros@redhat.com>
Tested-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251113074105.141379-3-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The zl3073x_ref, zl3073x_out and zl3073x_synth structures
previously stored state that was parsed from register reads. This
included values like boolean 'enabled' flags, synthesizer selections,
and pre-calculated frequencies.
This commit refactors the state management to store the raw register
values directly in these structures. The various inline helper functions
are updated to parse these raw values on-demand using FIELD_GET.
Reviewed-by: Petr Oros <poros@redhat.com>
Tested-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251113074105.141379-2-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Documentation build reported:
Warning: drivers/dpll/zl3073x/fw.c:365 function parameter 'comp' not described in 'zl3073x_fw_component_flash'
Warning: drivers/dpll/zl3073x/fw.c:365 expecting prototype for zl3073x_flash_bundle_flash(). Prototype was for zl3073x_fw_component_flash() instead
Warning: drivers/dpll/zl3073x/fw.c:365 No description found for return value of 'zl3073x_fw_component_flash'
The kernel-doc comment above `zl3073x_fw_component_flash()` used
the wrong function name (`zl3073x_flash_bundle_flash`) and omitted
the `@comp` parameter. Update the comment to correctly document
the `zl3073x_fw_component_flash()` function and its arguments.
Signed-off-by: Kriish Sharma <kriish.sharma2006@gmail.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251112055642.2597450-1-kriish.sharma2006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the signal format of an associated output is not considered
during output pin registration. As a result, the driver registers output
pins that are disabled by the signal format configuration.
Fix this by calling zl3073x_output_pin_is_enabled() to check whether
a given output pin should be registered or not.
Fixes: 75a71ecc24 ("dpll: zl3073x: Register DPLL devices and pins")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251027140912.233152-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The device-id-get and pin-id-get handlers were ignoring errors from
the find functions and sending empty replies instead of returning
error codes to userspace.
When dpll_device_find_from_nlattr() or dpll_pin_find_from_nlattr()
returned an error (e.g., -EINVAL for "multiple matches" or -ENODEV
for "not found"), the handlers checked `if (!IS_ERR(ptr))` and
skipped adding the device/pin handle to the message, but then still
sent the empty message as a successful reply.
This caused userspace tools to receive empty responses with id=0
instead of proper netlink errors with extack messages like
"multiple matches".
The bug is visible via strace, which shows the kernel sending TWO
netlink messages in response to a single request:
1. Empty reply (20 bytes, just header, no attributes):
recvfrom(3, [{nlmsg_len=20, nlmsg_type=dpll, nlmsg_flags=0, ...},
{cmd=0x7, version=1}], ...)
2. NLMSG_ERROR ACK with extack (because of NLM_F_ACK flag):
recvfrom(3, [{nlmsg_len=60, nlmsg_type=NLMSG_ERROR,
nlmsg_flags=NLM_F_CAPPED|NLM_F_ACK_TLVS, ...},
[{error=0, msg={...}},
[{nla_type=NLMSGERR_ATTR_MSG}, "multiple matches"]]], ...)
The C YNL library parses the first message, sees an empty response,
and creates a result object with calloc() which zero-initializes all
fields, resulting in id=0.
The Python YNL library parses both messages and displays the extack
from the second NLMSG_ERROR message.
Fix by checking `if (IS_ERR(ptr))` first and returning the error
code immediately, so that netlink properly sends only NLMSG_ERROR with
the extack message to userspace. After this fix, both C and Python
YNL tools receive only the NLMSG_ERROR and behave consistently.
This affects:
- DPLL_CMD_DEVICE_ID_GET: now properly returns error when multiple
devices match the criteria (e.g., same module-name + clock-id)
- DPLL_CMD_PIN_ID_GET: now properly returns error when multiple pins
match the criteria (e.g., same module-name)
Before fix:
$ dpll pin id-get module-name ice
0 (wrong - should be error, there are 17 pins with module-name "ice")
After fix:
$ dpll pin id-get module-name ice
Error: multiple matches
(correct - kernel reports the ambiguity via extack)
Fixes: 9d71b54b65 ("dpll: netlink: Add DPLL framework base functions")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251024190733.364101-1-poros@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the internal flash contains missing or corrupted configuration,
basic communication over the bus still functions, but the device
is not capable of normal operation (for example, using mailboxes).
This condition is indicated in the info register by the ready bit.
If this bit is cleared, the probe procedure times out while fetching
the device state.
Handle this case by checking the ready bit value in zl3073x_dev_start()
and skipping DPLL device and pin registration if it is cleared.
Do not report this condition as an error, allowing the devlink device
to be registered and enabling the user to flash the correct configuration.
Prior this patch:
[ 31.112299] zl3073x-i2c 1-0070: Failed to fetch input state: -ETIMEDOUT
[ 31.116332] zl3073x-i2c 1-0070: error -ETIMEDOUT: Failed to start device
[ 31.136881] zl3073x-i2c 1-0070: probe with driver zl3073x-i2c failed with error -110
After this patch:
[ 41.011438] zl3073x-i2c 1-0070: FW not fully ready - missing or corrupted config
Fixes: 75a71ecc24 ("dpll: zl3073x: Register DPLL devices and pins")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251008141445.841113-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Newer firmware bundles contain a flash utility whose size exceeds
the currently allowed limit. Increase the maximum allowed size
to accommodate the newer utility version.
Without this patch:
# devlink dev flash i2c/1-0070 file fw_nosplit_v3.hex
Failed to load firmware
Flashing failed
Error: zl3073x: FW load failed: [utility] component is too big (11000 bytes)
Fixes: ca017409da ("dpll: zl3073x: Add firmware loading functionality")
Suggested-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251008141418.841053-1-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The DPLL phase measurement block uses an exponential moving average with
a configurable averaging factor. Measurements are taken at approximately
40 Hz or at the reference frequency, whichever is lower.
Currently, factor=2 is used to prioritize fast response for dynamic
phase changes. For applications needing a stable, precise average phase
offset where rapid changes are unlikely, a higher factor is recommended.
Implement the .phase_offset_avg_factor_get/set callbacks to allow a user
to adjust this factor.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250927084912.2343597-4-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add new callback operations for a dpll device:
- phase_offset_avg_factor_get(...) - to obtain current phase offset
averaging factor from dpll device,
- phase_offset_avg_factor_set(...) - to set phase offset averaging factor
Obtain the factor value using the get callback and provide it to the user
if the device driver implement this callback. Execute the set callback upon
user requests, if the driver implement it.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
v2:
* do not require 'set' callback to retrieve current value
* always call 'set' callback regardless of current value
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250927084912.2343597-3-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR (net-6.17-rc7).
No conflicts.
Adjacent changes:
drivers/net/ethernet/mellanox/mlx5/core/en/fs.h
9536fbe10c ("net/mlx5e: Add PSP steering in local NIC RX")
7601a0a462 ("net/mlx5e: Add a miss level for ipsec crypto offload")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor DPLL initialization and move DPLL (de)registration, monitoring
control, fetching device invariant parameters and phase offset
measurement block setup to separate functions.
Use these new functions during device probe and teardown functions and
during changes to the clock_id devlink parameter.
These functions will also be used in the next patch implementing devlink
flash, where this functionality is likewise required.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20250909091532.11790-5-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add functionality for loading firmware files provided by the vendor
to be flashed into the device's internal flash memory. The firmware
consists of several components, such as the firmware executable itself,
chip-specific customizations, and configuration files.
The firmware file contains at least a flash utility, which is executed
on the device side, and one or more flashable components. Each component
has its own specific properties, such as the address where it should be
loaded during flashing, one or more destination flash pages, and
the flashing method that should be used.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20250909091532.11790-4-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To implement the devlink device flash functionality, the driver needs
to access both the device memory and the internal flash memory. The flash
memory is accessed using a device-specific program (called the flash
utility). This flash utility must be downloaded by the driver into
the device memory and then executed by the device CPU. Once running,
the flash utility provides a flash API to access the flash memory itself.
During this operation, the normal functionality provided by the standard
firmware is not available. Therefore, the driver must ensure that DPLL
callbacks and monitoring functions are not executed during the flash
operation.
Add all necessary functions for downloading the utility to device memory,
entering and exiting flash mode, and performing flash operations.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20250909091532.11790-3-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Besides the device host registers that are directly accessible, there
are also hardware registers that can be accessed indirectly via specific
host registers.
Add register definitions for accessing hardware registers and provide
helper functions for working with them. Additionally, extend the number
of pages in the regmap configuration to 256, as the host registers used
for accessing hardware registers are located on page 255.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20250909091532.11790-2-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The DPLL_CLOCK_QUALITY_LEVEL_ITU_OPT1_EPRC is not reported via netlink
due to bug in dpll_msg_add_clock_quality_level(). The usage of
DPLL_CLOCK_QUALITY_LEVEL_MAX for both DECLARE_BITMAP() and
for_each_set_bit() is not correct because these macros requires bitmap
size and not the highest valid bit in the bitmap.
Use correct bitmap size to fix this issue.
Fixes: a1afb959ad ("dpll: add clock quality level attribute and op")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Link: https://patch.msgid.link/20250912093331.862333-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the user is always asked about the Microchip Azurite
DPLL/PTP/SyncE core driver, even when I2C and SPI are disabled, and thus
the driver cannot be used at all.
Fix this by making the Kconfig symbol for the core driver invisible
(unless compile-testing), and selecting it by the bus glue sub-drivers.
Drop the modular defaults, as drivers should not default to enabled.
Fixes: 2df8e64e01 ("dpll: Add basic Microchip ZL3073x support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/97804163aeb262f0e0706d00c29d9bb751844454.1753874405.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If CONFIG_ZL3073X is enabled but both CONFIG_ZL3073X_I2C and
CONFIG_ZL3073X_SPI are disabled, the compilation may fail because
CONFIG_REGMAP is not enabled.
Fix the issue by selecting CONFIG_REGMAP when CONFIG_ZL3073X is enabled.
Fixes: 2df8e64e01 ("dpll: Add basic Microchip ZL3073x support")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20250726184145.25769-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement phase offset monitor feature to allow a user to monitor
phase offsets across all available inputs.
The device firmware periodically performs phase offsets measurements for
all available DPLL channels and input references. The driver can ask
the firmware to fill appropriate latch registers with measured values.
There are 2 sets of latch registers for phase offsets reporting:
1) DPLL-to-connected-ref: up to 5 registers that contain values for
phase offset between particular DPLL channel and its connected input
reference.
2) selected-DPLL-to-ref: 10 registers that contain values for phase
offsets between selected DPLL channel and all available input
references.
Both are filled with single read request so the driver can read
DPLL-to-connected-ref phase offset for all DPLL channels at once.
This was implemented in the previous patch.
To read selected-DPLL-to-ref registers for all DPLLs a separate read
request has to be sent to device firmware for each DPLL channel.
To implement phase offset monitor feature:
* Extend zl3073x_ref_phase_offsets_update() to select given DPLL channel
in phase offset read request. The caller can set channel==-1 if it
will not read Type2 registers.
* Use this extended function to update phase offset latch registers
during zl3073x_dpll_changes_check() call if phase monitor is enabled
* Extend zl3073x_dpll_pin_phase_offset_check() to check phase offset
changes for all available input references
* Extend zl3073x_dpll_input_pin_phase_offset_get() to report phase
offset values for all available input references
* Implement phase offset monitor callbacks to enable/disable this
feature
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Tested-by: Prathosh Satish <prathosh.satish@microchip.com>
Co-developed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20250715144633.149156-4-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
