Furong Xu says:
====================
net: stmmac: FPE via ethtool + tc
Move the Frame Preemption(FPE) over to the new standard API which uses
ethtool-mm/tc-mqprio/tc-taprio.
====================
Link: https://patch.msgid.link/cover.1725631883.git.0x1207@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop driver defined stmmac_fpe_state, and switch to common
ethtool_mm_verify_status for local TX verification status.
Local side and remote side verification processes are completely
independent. There is no reason at all to keep a local state and
a remote state.
Add a spinlock to avoid races among ISR, timer, link update
and register configuration.
This patch is based on Vladimir Oltean's proposal.
Vladimir Oltean says:
====================
In the INITIAL state, the timer sends MPACKET_VERIFY. Eventually the
stmmac_fpe_event_status() IRQ fires and advances the state to VERIFYING,
then rearms the timer after verify_time ms. If a subsequent IRQ comes in
and modifies the state to SUCCEEDED after getting MPACKET_RESPONSE, the
timer sees this. It must enable the EFPE bit now. Otherwise, it
decrements the verify_limit counter and tries again. Eventually it
moves the status to FAILED, from which the IRQ cannot move it anywhere
else, except for another stmmac_fpe_apply() call.
====================
Co-developed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/151f86c8428eba967039718c6bf90a7d841e703b.1725631883.git.0x1207@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Padding is not included in UDP and TCP checksums. Therefore, reduce the
length of the checksummed data to include only the data in the IP
payload. This fixes spurious reported checksum failures like
rx: pkt: sport=33000 len=26 csum=0xc850 verify=0xf9fe
pkt: bad csum
Technically it is possible for there to be trailing bytes after the UDP
data but before the Ethernet padding (e.g. if sizeof(ip) + sizeof(udp) +
udp.len < ip.len). However, we don't generate such packets.
Fixes: 91a7de8560 ("selftests/net: add csum offload test")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20240906210743.627413-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The probe() function is only used for DP83822 and DP83826 PHY,
leaving the private data pointer uninitialized for the DP83825 models
which causes a NULL pointer dereference in the recently introduced/changed
functions dp8382x_config_init() and dp83822_set_wol().
Add the dp8382x_probe() function, so all PHY models will have a valid
private data pointer to fix this issue and also prevent similar issues
in the future.
Fixes: 9ef9ecfa9e ("net: phy: dp8382x: keep WOL settings across suspends")
Signed-off-by: Tomas Paukrt <tomaspaukrt@email.cz>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/66w.ZbGt.65Ljx42yHo5.1csjxu@seznam.cz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch extends the same cs parser from JPEG v4.0.3 to
other JPEG versions (v2 and above).
Rename to more common name as jpeg_v2_dec_ring_parse_cs()
from jpeg_v4_0_3_dec_ring_parse_cs().
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: David (Ming Qiang) Wu <David.Wu3@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 88dcad2d07)
Cc: stable@vger.kernel.org
fix the pp_dpm_pcie issue on smu v14.0.2/3 as below:
0: 2.5GT/s, x4 250Mhz
1: 8.0GT/s, x4 616Mhz *
2: 8.0GT/s, x4 1143Mhz *
the middle level can be removed since it is always skipped on
smu v14.0.2/3
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit fedf6db3ea)
[Why]
drm_normalize_zpos will set the crtc_state->zpos_changed to 1 if any of
it's assigned planes changes zpos, or is removed/added from it.
To have amdgpu_dm request a plane reset on this is too broad. For
example, if only the cursor plane was moved from one crtc to another,
the crtc's zpos_changed will be set to true. But that does not mean that
the underlying primary plane requires a reset.
[How]
Narrow it down so that only the plane that has a change in zpos will
require a reset.
As a future TODO, we can further optimize this by only requiring a reset
on z-order change. Z-order is different from z-pos, since a zpos change
doesn't necessarily mean the z-ordering changed, and DC should only
require a reset if the z-ordering changed.
For example, the following zpos update does not change z-ordering:
Plane A: zpos 2 -> 3
Plane B: zpos 1 -> 2
=> Plane A is still on top of plane B: no reset needed
Whereas this one does change z-ordering:
Plane A: zpos 2 -> 1
Plane B: zpos 1 -> 2
=> Plane A changed from on top, to below plane B: reset needed
Fixes: 38e0c3df6d ("drm/amd/display: Move PRIMARY plane zpos higher")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3569
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 578aab4ecc)
dc_state_destruct() nulls the resource context of the DC state. The pipe
context passed to dcn35_set_drr() is a member of this resource context.
If dc_state_destruct() is called parallel to the IRQ processing (which
calls dcn35_set_drr() at some point), we can end up using already nulled
function callback fields of struct stream_resource.
The logic in dcn35_set_drr() already tries to avoid this, by checking tg
against NULL. But if the nulling happens exactly after the NULL check and
before the next access, then we get a race.
Avoid this by copying tg first to a local variable, and then use this
variable for all the operations. This should work, as long as nobody
frees the resource pool where the timing generators live.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3142
Fixes: 06ad7e1642 ("drm/amd/display: Destroy DC context while keeping DML and DML2")
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 0607a50c00)
Cc: stable@vger.kernel.org
dc_state_destruct() nulls the resource context of the DC state. The pipe
context passed to dcn10_set_drr() is a member of this resource context.
If dc_state_destruct() is called parallel to the IRQ processing (which
calls dcn10_set_drr() at some point), we can end up using already nulled
function callback fields of struct stream_resource.
The logic in dcn10_set_drr() already tries to avoid this, by checking tg
against NULL. But if the nulling happens exactly after the NULL check and
before the next access, then we get a race.
Avoid this by copying tg first to a local variable, and then use this
variable for all the operations. This should work, as long as nobody
frees the resource pool where the timing generators live.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3142
Fixes: 06ad7e1642 ("drm/amd/display: Destroy DC context while keeping DML and DML2")
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Tested-by: Raoul van Rüschen <raoul.van.rueschen@gmail.com>
Tested-by: Christopher Snowhill <chris@kode54.net>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Tested-by: Sefa Eyeoglu <contact@scrumplex.net>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit a3cc326a43)
Cc: stable@vger.kernel.org
Commit af28141498 ("block: freeze the queue in queue_attr_store")
changed queue_attr_store() to always freeze a sysfs attribute queue
before calling the attribute store() method, to ensure that no IOs are
in-flight when an attribute value is being updated.
However, this change created a potential deadlock situation for the
scheduler queue attribute as changing the queue elevator with
elv_iosched_store() can result in a call to request_module() if the user
requested module is not already registered. If the file of the requested
module is stored on the block device of the frozen queue, a deadlock
will happen as the read operations triggered by request_module() will
wait for the queue freeze to end.
Solve this issue by introducing the load_module method in struct
queue_sysfs_entry, and to calling this method function in
queue_attr_store() before freezing the attribute queue.
The macro definition QUEUE_RW_LOAD_MODULE_ENTRY() is added to define a
queue sysfs attribute that needs loading a module.
The definition of the scheduler atrribute is changed to using
QUEUE_RW_LOAD_MODULE_ENTRY(), with the function
elv_iosched_load_module() defined as the load_module method.
elv_iosched_store() can then be simplified to remove the call to
request_module().
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Reported-by: Jiri Jaburek <jjaburek@redhat.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219166
Fixes: af28141498 ("block: freeze the queue in queue_attr_store")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Link: https://lore.kernel.org/r/20240908000704.414538-1-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit <17de3f5fdd35> ("iommu: Retire bus ops") removes iommu ops from
the bus structure. The iommu subsystem no longer relies on bus for
operations. So iommu_domain_alloc() interface is no longer relevant.
Replace iommu_domain_alloc() with iommu_paging_domain_alloc() which takes
the physical device from which the host1x_device virtual device was
instantiated. This physical device is a common parent to all physical
devices that are part of the virtual device.
Suggested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240902014700.66095-4-baolu.lu@linux.intel.com
This ignores errors from HCI_OP_REMOTE_NAME_REQ_CANCEL since it
shouldn't interfere with the stopping of discovery and in certain
conditions it seems to be failing.
Link: https://github.com/bluez/bluez/issues/575
Fixes: d0b137062b ("Bluetooth: hci_sync: Rework init stages")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If HCI_CONN_MGMT_CONNECTED has been set then the event shall be
HCI_CONN_MGMT_DISCONNECTED.
Fixes: b644ba3369 ("Bluetooth: Update device_connected and device_found events to latest API")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For tracking multiple devices concurrently with a condition.
The patch enables the HCI_QUIRK_USE_MSFT_EXT_ADDRESS_FILTER quirk
on RTL8852B controller.
The quirk setting is based on commit 9e14606d8f ("Bluetooth: msft:
Extended monitor tracking by address filter")
With this setting, when a pattern monitor detects a device, this
feature issues an address monitor for tracking that device. Let the
original pattern monitor keep monitor new devices.
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A LED trigger's activate() callback gets called when the LED trigger
gets activated for a specific LED, so that the trigger code can ensure
the LED state matches the current state of the trigger condition
(LED_FULL when HCI_UP is set in this case).
led_trigger_event() is intended for trigger condition state changes and
iterates over _all_ LEDs which are controlled by this trigger changing
the brightness of each of them.
In the activate() case only the brightness of the LED which is being
activated needs to change and that LED is passed as an argument to
activate(), switch to led_set_brightness() to only change the brightness
of the LED being activated.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use kvmemdup instead of kvmalloc() + memcpy() to simplify the code.
No functional change intended.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Starting a BCM UART controller not defined as a platform device or
a serdev with "btattach -B /dev/ttyS1 -P bcm -S 3000000" works fine
but the serial port remains at the init_speed, i.e. 115200.
The oper_speed is only set if a device is declared in ACPI, device
tree or as a platform device.
This commit copies the serial port speed fixed by hciattach to the
oper_speed on line discipline opening.
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Since kzalloc already zeroes the allocated memory, the subsequent
memset call is unnecessary. This patch removes the redundant memset to
clean up the code and enhance efficiency.
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Describe the inputs from the PMU that the Bluetooth module on wcn6855
consumes and drop the ones from the host. This breaks the current
contract but the only two users of wcn6855 upstream - sc8280xp based
boards - will be updated in DTS patches sent separately while the
hci_qca driver will remain backwards compatible with older DT sources.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This enables btnxpuart driver to handle ISO RX packet when DUT is
configured as audio sink.
Tested IW612 on iMX8MMini platform and BlueZ-5.77 as follows:
1) Configured DUT with bap_bcast_sink role in pipewire configuration file.
2) Started pipewire and DUT is able to sync with Broadcast source through
pipewire.
3) ISO data RX is seen in btmon.
4) Audio/Music is heard on audio jack.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Tested-by: Sarveshwar Bajaj <sarveshwar.bajaj@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds ISO packet support in h4_recv.h, which was created before ISO
packet handling was added to hci_h4.c and hci_uart.c
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This inverts the LE State flag so by default we assume the controllers
would report valid states rather than invalid so it is inline with the
respective quirk (HCI_QUIRK_BROKEN_LE_STATES).
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add Amlogic Bluetooth entry to MAINTAINERS to clarify the maintainers
Signed-off-by: Yang Li <yang.li@amlogic.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add a new HCI protocol HCI_UART_AML for the Amlogic Bluetooth
controller. It works on the standard H4 protocol via a 4-wire UART
interface, with baud rates up to 4 Mbps.
The controller supports two types of commands: the TCI commands and the
vendor command. The former is for initial setup including setting baud
rates, downloading fw, starting chip and etc, while the latter is for
dumping firmware versions and setting public address after firmware
updates and normal startup.
It was verified on board of T602 (S905X4 + W265S2).
dmesg:
..
[ 5.313450] Bluetooth: HCI UART protocol AML registered
[ 6.506052] Bluetooth: hci0: fw_version: date = 42.28, number = 0xb2fd
...
Co-developed-by: Ye He <ye.he@amlogic.com>
Signed-off-by: Ye He <ye.he@amlogic.com>
Signed-off-by: Yang Li <yang.li@amlogic.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add a helper function hci_iso_hdr() to extract iso header from skb.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Pull tracing fixes from Steven Rostedt:
- Move declaration of interface_lock outside of CONFIG_TIMERLAT_TRACER
The fix to some locking races moved the declaration of the
interface_lock up in the file, but also moved it into the
CONFIG_TIMERLAT_TRACER #ifdef block, breaking the build when that
wasn't set. Move it further up and out of that #ifdef block.
- Remove unused function run_tracer_selftest() stub
When CONFIG_FTRACE_STARTUP_TEST is not set the stub function
run_tracer_selftest() is not used and clang is warning about it.
Remove the function stub as it is not needed.
* tag 'trace-v6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Drop unused helper function to fix the build
tracing/osnoise: Fix build when timerlat is not enabled
