Commit 5fabb01207 ("net: stmmac: Add initial XDP support") sets
PP_FLAG_DMA_SYNC_DEV flag for page_pool unconditionally,
page_pool_recycle_direct() will call page_pool_dma_sync_for_device()
on every page even the page is not going to be reused by XDP program.
When XDP is not enabled, the page which holds the received buffer
will be recycled once the buffer is copied into new SKB by
skb_copy_to_linear_data(), then the MAC core will never reuse this
page any longer. Always setting PP_FLAG_DMA_SYNC_DEV wastes CPU cycles
on unnecessary calling of page_pool_dma_sync_for_device().
After this patch, up to 9% noticeable performance improvement was observed
on certain platforms.
Fixes: 5fabb01207 ("net: stmmac: Add initial XDP support")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Link: https://patch.msgid.link/20240919121028.1348023-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, the virtio-net driver will perform a pre-dma-mapping for
small or mergeable RX buffer. But for small packets, a mismatched address
without VIRTNET_RX_PAD and xdp_headroom is used for unmapping.
That will result in unsynchronized buffers when SWIOTLB is enabled, for
example, when running as a TDX guest.
This patch unifies the address passed to the virtio core as the address of
the virtnet header and fixes the mismatched buffer address.
Changes from v2: unify the buf that passed to the virtio core in small
and merge mode.
Changes from v1: Use ctx to get xdp_headroom.
Fixes: 295525e29a ("virtio_net: merge dma operations when filling mergeable buffers")
Signed-off-by: Wenbo Li <liwenbo.martin@bytedance.com>
Signed-off-by: Jiahui Cen <cenjiahui@bytedance.com>
Signed-off-by: Ying Fang <fangying.tommy@bytedance.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Link: https://patch.msgid.link/20240919081351.51772-1-liwenbo.martin@bytedance.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
syzbot reported a WARNING in bond_xdp_get_xmit_slave. To reproduce
this[1], one bond device (bond1) has xdpdrv, which increases
bpf_master_redirect_enabled_key. Another bond device (bond0) which is
unsupported by XDP but its slave (veth3) has xdpgeneric that returns
XDP_TX. This triggers WARN_ON_ONCE() from the xdp_master_redirect().
To reduce unnecessary warnings and improve log management, we need to
delete the WARN_ON_ONCE() and add ratelimit to the netdev_err().
[1] Steps to reproduce:
# Needs tx_xdp with return XDP_TX;
ip l add veth0 type veth peer veth1
ip l add veth3 type veth peer veth4
ip l add bond0 type bond mode 6 # BOND_MODE_ALB, unsupported by XDP
ip l add bond1 type bond # BOND_MODE_ROUNDROBIN by default
ip l set veth0 master bond1
ip l set bond1 up
# Increases bpf_master_redirect_enabled_key
ip l set dev bond1 xdpdrv object tx_xdp.o section xdp_tx
ip l set veth3 master bond0
ip l set bond0 up
ip l set veth4 up
# Triggers WARN_ON_ONCE() from the xdp_master_redirect()
ip l set veth3 xdpgeneric object tx_xdp.o section xdp_tx
Reported-by: syzbot+c187823a52ed505b2257@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c187823a52ed505b2257
Fixes: 9e2ee5c7e7 ("net, bonding: Add XDP support to the bonding driver")
Signed-off-by: Jiwon Kim <jiwonaid0@gmail.com>
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20240918140602.18644-1-jiwonaid0@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The RX frame size limit should not be based on the current MTU setting.
Instead it should be based on the hardware capabilities.
While we're here, improve the description of the receive frame length
setting as suggested by Niklas.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The datasheets for all SoCs using the GbEth IP specify a maximum
transmission frame size of 1.5 kByte. I've confirmed through internal
discussions that support for 1522 byte frames has been validated, which
allows us to support the default MTU of 1500 bytes after reserving space
for the Ethernet header, frame checksums and an optional VLAN tag.
Fixes: 2e95e08ac0 ("ravb: Add rx_max_buf_size to struct ravb_hw_info")
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The commit b8c43360f6 ("net: stmmac: No need to calculate speed divider
when offload is disabled") allows the "port_transmit_rate_kbps" to be
set to a value of 0, which is then passed to the "div_s64" function when
tc-cbs is disabled. This leads to a zero-division error.
When tc-cbs is disabled, the idleslope, sendslope, and credit values the
credit values are not required to be configured. Therefore, adding a return
statement after setting the txQ mode to DCB when tc-cbs is disabled would
prevent a zero-division error.
Fixes: b8c43360f6 ("net: stmmac: No need to calculate speed divider when offload is disabled")
Cc: <stable@vger.kernel.org>
Co-developed-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: KhaiWenTan <khai.wen.tan@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240918061422.1589662-1-khai.wen.tan@linux.intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In the ether3_probe function, a timer is initialized with a callback
function ether3_ledoff, bound to &prev(dev)->timer. Once the timer is
started, there is a risk of a race condition if the module or device
is removed, triggering the ether3_remove function to perform cleanup.
The sequence of operations that may lead to a UAF bug is as follows:
CPU0 CPU1
| ether3_ledoff
ether3_remove |
free_netdev(dev); |
put_devic |
kfree(dev); |
| ether3_outw(priv(dev)->regs.config2 |= CFG2_CTRLO, REG_CONFIG2);
| // use dev
Fix it by ensuring that the timer is canceled before proceeding with
the cleanup in ether3_remove.
Fixes: 6fd9c53f71 ("net: seeq: Convert timers to use timer_setup()")
Signed-off-by: Kaixin Wang <kxwang23@m.fudan.edu.cn>
Link: https://patch.msgid.link/20240915144045.451-1-kxwang23@m.fudan.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
axienet_free_tx_chain returns the number of DMA descriptors it's
handled. However, axienet_tx_poll treats the return as the number of
packets. When scatter-gather SKBs are enabled, a single packet may use
multiple DMA descriptors, which causes incorrect packet counts. Fix this
by explicitly keepting track of the number of packets processed as
separate from the DMA descriptors.
Budget does not affect the number of Tx completions we can process for
NAPI, so we use the ring size as the limit instead of budget. As we no
longer return the number of descriptors processed to axienet_tx_poll, we
now update tx_bd_ci in axienet_free_tx_chain.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20240913145156.2283067-1-sean.anderson@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The author of the blamed commit apparently did not notice something
about aqr_wait_reset_complete(): it polls the exact same register -
MDIO_MMD_VEND1:VEND1_GLOBAL_FW_ID - as aqr_firmware_load().
Thus, the entire logic after the introduction of aqr_wait_reset_complete() is
now completely side-stepped, because if aqr_wait_reset_complete()
succeeds, MDIO_MMD_VEND1:VEND1_GLOBAL_FW_ID could have only been a
non-zero value. The handling of the case where the register reads as 0
is dead code, due to the previous -ETIMEDOUT having stopped execution
and returning a fatal error to the caller. We never attempt to load
new firmware if no firmware is present.
Based on static code analysis, I guess we should simply introduce a
switch/case statement based on the return code from aqr_wait_reset_complete(),
to determine whether to load firmware or not. I am not intending to
change the procedure through which the driver determines whether to load
firmware or not, as I am unaware of alternative possibilities.
At the same time, Russell King suggests that if aqr_wait_reset_complete()
is expected to return -ETIMEDOUT as part of normal operation and not
just catastrophic failure, the use of phy_read_mmd_poll_timeout() is
improper, since that has an embedded print inside. Just open-code a
call to read_poll_timeout() to avoid printing -ETIMEDOUT, but continue
printing actual read errors from the MDIO bus.
Fixes: ad649a1fac ("net: phy: aquantia: wait for FW reset before checking the vendor ID")
Reported-by: Clark Wang <xiaoning.wang@nxp.com>
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Closes: https://lore.kernel.org/netdev/8ac00a45-ac61-41b4-9f74-d18157b8b6bf@nvidia.com/
Reported-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Closes: https://lore.kernel.org/netdev/c7c1a3ae-be97-4929-8d89-04c8aa870209@gmx.net/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Link: https://patch.msgid.link/20240913121230.2620122-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The HSR stack allows to offload its Tx packet duplication functionality to
the hardware. Enable this offloading feature for ICSSG driver. Add support
to offload HSR Tx Tag Insertion and Rx Tag Removal and duplicate discard.
hsr tag insertion offload and hsr dup offload are tightly coupled in
firmware implementation. Both these features need to be enabled / disabled
together.
Duplicate discard is done as part of RX tag removal and it is
done by the firmware. When driver sends the r30 command
ICSSG_EMAC_HSR_RX_OFFLOAD_ENABLE, firmware does RX tag removal as well as
duplicate discard.
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://patch.msgid.link/20240911081603.2521729-5-danishanwar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for offloading HSR port-to-port frame forward to hardware.
When the slave interfaces are added to the HSR interface, the PRU cores
will be stopped and ICSSG HSR firmwares will be loaded to them.
Similarly, when HSR interface is deleted, the PRU cores will be
restarted and the last used firmwares will be reloaded. PRUeth
interfaces will be back to the last used mode.
This commit also renames some APIs that are common between switch and
hsr mode with '_fw_offload' suffix.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://patch.msgid.link/20240911081603.2521729-4-danishanwar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Display channel info in the RPM map debugfs output.
With this, cat /sys/kernel/debug/cn10k/rvu_pf_rpm_map
would display channel number for each device in addition to
the existing data.
Sample output:
PCI dev RVU PF Func NIX block rpm LMAC CHAN
0002:02:00.0 0x400 NIX0 rpm0 LMAC0 256
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Link: https://patch.msgid.link/20240912161450.164402-3-lcherian@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
pull-request: can-next 2024-09-11
The first patch is by Uwe Kleine-König targets all CAN platform driver
and switches back the remove function to struct
platform_driver::remove().
A patch by Stefan Mätje fixes the help text of the ESD USB driver.
Jake Hamby's patch masks an unneeded interrupt in the m_can driver.
The last 2 patches target the rockchip_canfd driver. Arnd Bergmann's
patch reworks the delay calculation for the timekeeping worker, a
patch by me fixes the decoding of the error code register.
* tag 'linux-can-next-for-6.12-20240911' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: rockchip_canfd: rkcanfd_handle_error_int_reg_ec(): fix decoding of error code register
can: rockchip_canfd: rkcanfd_timestamp_init(): rework delay calculation
can: m_can: m_can_chip_config(): mask timestamp wraparound IRQ
can: usb: Kconfig: Fix list of devices for esd_usb driver
can: Switch back to struct platform_driver::remove()
====================
Link: https://patch.msgid.link/20240912080438.2826895-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
pull-request: can 2024-09-12
Kuniyuki Iwashima's patch fixes an incomplete bug fix in the CAN BCM
protocol, which was introduced during v6.11.
A patch by Stefan Mätje removes the unsupported CAN_CTRLMODE_3_SAMPLES
mode for CAN-USB/3-FD devices in the esd_usb driver.
The next patch is by Martin Jocic and enables 64-bit DMA addressing
for the kvaser_pciefd driver.
The last two patches both affect the m_can driver. Jake Hamby's patch
activates NAPI before interrupts are activated, a patch by me moves
the stopping of the clock after the device has been shut down.
* tag 'linux-can-fixes-for-6.11-20240912' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: m_can: m_can_close(): stop clocks after device has been shut down
can: m_can: enable NAPI before enabling interrupts
can: kvaser_pciefd: Enable 64-bit DMA addressing
can: esd_usb: Remove CAN_CTRLMODE_3_SAMPLES for CAN-USB/3-FD
can: bcm: Clear bo->bcm_proc_read after remove_proc_entry().
====================
Link: https://patch.msgid.link/20240912075804.2825408-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The enetc driver uses ifdefs when checking whether
CONFIG_FSL_ENETC_PTP_CLOCK is enabled in a number of places. This works
if the driver is built-in but fails if the driver is available as a
kernel module. Replace the instances of ifdef with use of the IS_ENABLED
macro, that will evaluate as true when this feature is built as a kernel
module and follows the kernel's coding style.
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240912173742.484549-1-martyn.welch@collabora.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver calls netif_napi_set_irq() and then calls netif_napi_add(),
which calls netif_napi_add_weight(). At the end of
netif_napi_add_weight() is a call to netif_napi_set_irq(napi, -1), which
clears the previously set napi->irq value. Fix this by calling
netif_napi_set_irq() after calling netif_napi_add().
This was found when reviewing another patch and I have no way to test
this, but the fix seemed relatively straight forward.
Fixes: bc6107771b ("eth: fbnic: Allocate a netdevice and napi vectors with queues")
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20240912174922.10550-1-brett.creeley@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
En-Wei reported that traffic breaks if cable is unplugged for more
than 3s and then re-plugged. This was supposed to be fixed by
621735f590 ("r8169: fix rare issue with broken rx after link-down on
RTL8125"). But apparently this didn't fix the issue for everybody.
The 3s threshold rang a bell, as this is the delay after which ALDPS
kicks in. And indeed disabling ALDPS fixes the issue for this user.
Maybe this fixes the issue in general. In a follow-up step we could
remove the first fix attempt and see whether anybody complains.
Fixes: f1bce4ad2f ("r8169: add support for RTL8125")
Tested-by: En-Wei WU <en-wei.wu@canonical.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/778b9d86-05c4-4856-be59-cde4487b9e52@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During the introduction of struct bpf_net_context handling for
XDP-redirect, the netkit driver has been missed, which also requires it
because NETKIT_REDIRECT invokes skb_do_redirect() which is accessing the
per-CPU variables. Otherwise we see the following crash:
BUG: kernel NULL pointer dereference, address: 0000000000000038
bpf_redirect()
netkit_xmit()
dev_hard_start_xmit()
Set the bpf_net_context before invoking netkit_xmit() program within the
netkit driver.
Fixes: 401cb7dae8 ("net: Reference bpf_redirect_info via task_struct on PREEMPT_RT.")
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Acked-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20240912155620.1334587-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that we support multiple RX queues, enable default priority
to flow mapping so that higher priority packets come on higher
channels (flows).
The Classifier checks for PCP/DSCP priority in the packet and
routes them to the appropriate flow.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Policer registers in the ALE register space are just shadow registers
and use an index field in the policer table control register to read/write
to the actual Polier registers.
Add helper functions to Read and Write to Policer registers.
Also add a helper function to set the thread value to classifier/policer
mapping. Any packet that first matches the classifier will be sent to the
thread (flow) that is set in the classifier to thread mapping table.
If not set then it goes to the default flow.
Default behaviour is to have 8 classifiers to map 8 DSCP/PCP
priorities to N receive threads (flows). N depends on number of
RX channels enabled for the port.
As per the standard [1] User prioritie 1 (Background) and 2 (Spare) have
lower priority than the user priority 0 (default). User priority 1 being
of the lowest priority.
[1] IEEE802.1D-2004, IEEE Standard for Local and metropolitan area networks
Table G-2 - Traffic type acronyms
Table G-3 - Defining traffic types
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
